Add the DT nodes required to probe the CFI compatible parallel monitor
flash found on the Malta development board, and remove the platform
code that was previously doing it. Delete the now-empty malta-platform.c
file. Adjust the Malta defconfigs that enable MTD & the pflash/CFI
driver to enable CONFIG_MTD_PHYSMAP_OF rather than CONFIG_MTD_PHYSMAP in
order to preserve their behaviour.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14278/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the CPU, GIC & i8259 interrupt controllers present in the Malta
system using device tree. This enables interrupts to be provided to
devices using device tree as they are moved over to being probed using
it.
Since Malta is very configurable it's unknown whether a GIC will be
present at compile time. In order to support both cases the
malta_dt_shim code is added in order to detect whether a GIC is present,
adjusting the DT to route interrupts correctly and nop out the GIC node
if no GIC is found.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14274/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Malta boards can have more than 256MB DDR available, but we have
previously only made use of up to 256MB (ie. the DDR accessible via
kseg0) by default, without the user manually specifying mem= kernel
parameters. This patch causes all available DDR, as reported by the
bootloader via the ememsize or memsize environment variables or
optionally on the command line, to be used when possible without the
user needing to manually provide the memory ranges.
Malta now has 2 subtly different memory maps which have to be taken into
account when setting this up. The original memory map (referred to by
the code as v1) has up to 2GB of DDR aliased in both the upper & lower
halves of the 32 bit physical address space, with a 256MB I/O region
obscuring 0x10000000-0x1fffffff only in the lower alias. The revised v2
memory map is flat with up to 4GB DDR starting from 0x0, and the I/O
region obscures 256MB of DDR which becomes inacessible. The memory map
in use is indicated by a register provided by the rocit2 system
controller, which is checked in order to set up the kernels memory
ranges accordingly.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14273/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Set the PCI_BAR0 register in all configurations such that PCI devices
can perform DMA to all of the bottom 2GB of the physical address space.
This is imperfect if we make use of the legacy Malta memory map, but it
is an improvement on the inconsistent values setup before.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14272/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The i8259A_irq_pending function is unused. Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14271/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The default i8259 polling function (i8259_irq) is nicely generic but is
fairly costly. Platforms often provide an alternative means of polling
for an i8259 interrupt, and when using the i8259 without device tree
have typically just chained its parent interrupt to their own handler
function. In order to allow for platform-specific polling functions to
be used in cases where the driver is probed via device tree, provide an
i8259_set_poll function that accepts a pointer to an alternative poll
function that will override the default.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14270/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SEAD3 board defines a custom implementation of read_persistent_clock
which does exactly the same dummy operation as the generic weak version.
Remove the not really implemented custom version.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14064/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the img-ascii-lcd driver using device tree in order to display a
message on the SEAD3 board's LCD display, and remove the platform code
that was formerly performing this function. This removes more platform
code and moves SEAD3 further towards being entirely DT-based.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14063/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 2 line * 16 character LCD display on the SEAD3 board has no real use
as a framebuffer device. It's far too small to produce any meaningful
output if used as the kernel console, SEAD3 is a development board that
will essentially always have a far more useful UART connection & the
code in sead3-display.c will overwrite whatever's on the display every
second anyway. Remove this unused code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14059/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
more victims of indirect include chains - au1200fb
lasat/picvue_proc and watchdog/ath79_wdt
... as well as tb0219, spotted by Sudip Mukherjee
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Parse the memsize argument provided by the bootloader in the DT shim
code, allowing the user to override it on the command line. This places
all of the DT manipulation code into sead3-dtshim.c.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14058/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove the custom platform code to restart when instructed to power off,
instead relying upon the generic restart-poweroff driver probed via DT
to do the same thing.
Remove also the halt implementation, which is incorrect. The generic
MIPS version will hang the system as halt should.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14057/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe a driver for the PLED & FLED LEDs found on the SEAD3 board using
the register-bit-led driver via device tree, rather than a custom driver
via platform code. Enable support for the register-bit-led driver & its
prerequisite syscon in sead3_defconfig.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14054/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the SEAD3 EHCI controller using the generic-ehci driver & device
tree rather than platform code, in order to reduce the amount of the
latter.
Now that no devices probed from platform code require interrupts, remove
the retrieval of the IRQ domain & sead3int.h.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14051/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Stop selecting SYS_HAS_EARLY_PRINTK & remove the custom support for
early output to the ns16550a UARTs, instead relying upon generic
ns16550a earlycon support. This reduces the amount of platform code
required for SEAD3 without losing any functionality.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14049/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the UARTs on SEAD3 boards using device tree rather than platform
code, in order to reduce the amount of the latter. This requires that
CONFIG_SERIAL_OF_PLATFORM be enabled, so enable it in sead3_defconfig.
The SEAD3 DT shim code is extended to read bootloader environment
variables to determine the appropriate UART & mode for kernel console
output & set the stdout-path property of the chosen node accordingly.
In contrast to the old platform code, which appears to have only ever
set "console=ttyS0,38400n8r" with the code in console_config never
having an effect, this will honor the "yamontty" environment variable to
select between the 2 UARTs on the board and then check the "modetty0" or
"modetty1" variable as appropriate to determine the UART configuration.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14048/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Probe the CPU interrupt controller & optional Global Interrupt
Controller (GIC) using devicetree rather than platform code. Because the
bootloader on SEAD3 does not provide a device tree to the kernel & the
device tree is always built in, we patch out the GIC node during boot if
we detect that a GIC is not present in the system.
The appropriate IRQ domain is discovered by platform code setting up
device IRQ numbers temporarily. It will be removed by further patches
which move the devices towards being probed via device tree.
No behavioural change is intended by this patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14047/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split the obj-y entries for SEAD3 onto a line each, so that they're more
independent & can be modified more clearly by later commits.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14046/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS Coherent Processing System (CPS) power management code has
previously generated code used to enter low power idle states once
during boot for all CPUs. This has the drawback that if a CPU is present
in the system but not being used (for example due to the maxcpus kernel
parameter) then we encounter problems due to not having probed that CPU
for information about its type & properties. The result of this is that
we generate entry code which is both unused, potentially entirely
invalid & likely to be unsuitable for the CPU in question anyway.
Avoid this by generating idle state entry code only when a CPU is
brought online. This way we only ever generate code for CPUs that we
know we've probed the properties of, and that will actually be used.
[ralf@linux-mips.org: Resolve merge conflict.]
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14259/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. In the case of
kvm where it is modular, we can extend that to also include files
that are building basic support functionality but not related
to loading or registering the final module; such files also have
no need whatsoever for module.h
The advantage in removing such instances is that module.h itself
sources about 15 other headers; adding significantly to what we feed
cpp, and it can obscure what headers we are effectively using.
Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each instance for the
presence of either and replace as needed. In this case, we did
not need to add either to any files.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: kvm@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14036/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. The advantage
in doing so is that module.h itself sources about 15 other headers;
adding significantly to what we feed cpp, and it can obscure what
headers we are effectively using.
Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each obj-y/bool instance
for the presence of either and replace as needed.
We also needed to remove the no-op MODULE_DEVICE_TABLE usage in
several instances to permit removal of the module.h include. The
files in these instances were all controlled by bool Kconfig.
In one instance, module_param was being used so we transition the
module.h include onto a moduleparam.h include.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14035/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. The advantage
in doing so is that module.h itself sources about 15 other headers;
adding significantly to what we feed cpp, and it can obscure what
headers we are effectively using.
Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each obj-y/bool instance
for the presence of either and replace as needed.
The compiler.h additions are for an implict presence of the
"notrace" which module.h brought in but export.h does not.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14034/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. The advantage
in doing so is that module.h itself sources about 15 other headers;
adding significantly to what we feed cpp, and it can obscure what
headers we are effectively using.
Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each obj-y/bool instance
for the presence of either and replace as needed.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14033/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Historically a lot of these existed because we did not have
a distinction between what was modular code and what was providing
support to modules via EXPORT_SYMBOL and friends. That changed
when we forked out support for the latter into the export.h file.
This means we should be able to reduce the usage of module.h
in code that is obj-y Makefile or bool Kconfig. The advantage
in doing so is that module.h itself sources about 15 other headers;
adding significantly to what we feed cpp, and it can obscure what
headers we are effectively using.
Since module.h was the source for init.h (for __init) and for
export.h (for EXPORT_SYMBOL) we consider each obj-y/bool instance
for the presence of either and replace as needed.
In the case of the n32/o32 files, we have to get rid of a couple
no-op MODULE_ tags to facilitate the module.h removal. They piggy
back off the fs/ elf binary support, which is also a bool Kconfig.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14032/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the MIPS remote processor implementation, we need additional IPIs to
talk to the remote processor. Since MIPS GIC reserves exactly the right
number of IPI IRQs required by Linux for the number of VPs in the
system, this is not possible without releasing some recources.
This commit introduces mips_smp_ipi_allocate() which allocates IPIs to a
given cpumask. It is called as normal with the cpu_possible_mask at
bootup to initialise IPIs to all CPUs. mips_smp_ipi_free() may then be
used to free IPIs to a subset of those CPUs so that their hardware
resources can be reused.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Lisa Parratt <Lisa.Parratt@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-remoteproc@vger.kernel.org
Cc: lisa.parratt@imgtec.com
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14285/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When adding a wired entry to the TLB via add_wired_entry, the tlb is
flushed with local_flush_tlb_all, which on CPUs with TLBINV results in
the new wired entry being flushed again.
Behavior of the TLBINV instruction applies to all applicable TLB entries
and is unaffected by the setting of the Wired register. Therefore if
the TLB has any wired entries, fall back to iterating over the entries
rather than blasting them all using TLBINVF.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: lisa.parratt@imgtec.com
Cc: Hugh Dickins <hughd@google.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-remoteproc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14283/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
flush_icache_range() flushes icache lines in a protected fashion for
kernel addresses, however this isn't correct with EVA where protected
cache ops only operate on user addresses, making flush_icache_range()
ineffective.
Split the implementations of __flush_icache_user_range() from
flush_icache_range(), changing the normal flush_icache_range() to use
unprotected normal cache ops.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14156/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert KVM dynamic translation of guest instructions to flush icache
for guest mapped addresses using the new
__local_flush_icache_user_range() API to allow the more generic
flush_icache_range() to be changed to work on kernel addresses only.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14155/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Update arch_uprobe_copy_ixol() to use the kmap_atomic() based kernel
address to flush the icache with flush_icache_range(), rather than the
user mapping. We have the kernel mapping available anyway and this
avoids having to switch to using the new __flush_icache_user_range() for
the sake of Enhanced Virtual Addressing (EVA) where flush_icache_range()
will become ineffective on user addresses.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14154/
Patchwork: https://patchwork.linux-mips.org/patch/14308/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cacheflush(2) system call uses flush_icache_range() to flush a range
of usermode addresses from the icache, so change it to utilise the new
__flush_icache_user_range() API to allow the more generic
flush_icache_range() to be changed to work on kernel addresses only.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14153/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
flush_icache_range() is used for both user addresses (i.e.
cacheflush(2)), and kernel addresses (as the API documentation
describes).
This isn't really suitable however for Enhanced Virtual Addressing (EVA)
where cache operations on usermode addresses must use a different
instruction, and the protected cache ops assume user addresses, making
flush_icache_range() ineffective on kernel addresses.
Split out a new __flush_icache_user_range() and
__local_flush_icache_user_range() for users which actually want to flush
usermode addresses (note that flush_icache_user_range() already exists
on various architectures but with different arguments).
The implementation of flush_icache_range() will be changed in an
upcoming commit to use unprotected normal cache ops so as to always work
on the kernel mode address space.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14152/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The EVA conditional bc_wback_inv() at the end of flush_icache_range() to
flush the modified code all the way back to RAM was apparently there for
debug purposes and to accommodate the Malta EVA configuration which
makes use of a physical alias, and didn't use the CP0_EBase.WG (Write
Gate) bit to put the exception vector in the same physical alias where
the exception vector code is written and is being flushed.
Now that CP0_EBase.WG is used, lets drop this flush.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14151/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On CPUs which support the EBase WG (write gate) flag, the most
significant bits of the exception base can be changed. Firmware running
on a VP(E) using MIPS rproc may change EBase to point into the user
segment where the firmware is located such that it can service
interrupts. When control is transferred back to the kernel the EBase
must be switched back into the kernel segment, such that the kernel's
exception vectors are used.
Similarly when vectored interrupts (vint) or vectored external interrupt
controllers (veic) are enabled an exception vector is allocated from
bootmem, and written to the EBase register. Due to the WG flag being
clear, only bits 29:12 will be written. Asside from the rproc case above
this is normally fine (as it will usually be a low allocation within the
KSeg0 range, however when Enhanced Virtual Addressing (EVA) is enabled
the allocation may be outside of the traditional KSeg0/KSeg1 address
range, resulting in the wrong EBase being written.
Correct both cases (configure_exception_vector() for the boot CPU, and
per_cpu_trap_init() for secondary CPUs) to write EBase with the WG flag
first if supported.
On the Malta EVA configuration, KSeg0 is mapped to physical address 0,
and memory is allocated from the KUSeg segment which is mapped to
physical address 0x80000000, which physically aliases the RAM at 0. This
only worked due to the exception base address aliasing the same
underlying RAM that was written to & cache flushed, and due to
flush_icache_range() going beyond the call of duty and flushing from the
L2 cache too (due to the differing physical addresses).
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14150/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When allocating boot memory for the exception vector when vectored
interrupts (vint) or vectored external interrupt controllers (veic) are
enabled, try to ensure that the virtual address resides in KSeg0 (and
WARN should that not be possible).
This will be helpful on MIPS64 cores supporting the CP0_EBase Write Gate
(WG) bit once we start using the WG bit to write the full ebase into
CP0_EBase, as we ideally need to avoid hitting the architecturally
poorly defined exception base for Cache Errors when CP0_EBase is in
XKPhys.
An exception is made for Enhanced Virtual Addressing (EVA) kernels which
allow segments to be rearranged and to become uncached during cache
error handling, making it valid for ebase to be elsewhere.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14149/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When reading the CP0_EBase register containing the WG (write gate) bit,
the ebase variable should be set to the full value of the register, i.e.
on a 64-bit kernel the full 64-bit width of the register via
read_cp0_ebase_64(), and on a 32-bit kernel the full 32-bit width
including bits 31:30 which may be writeable.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14148/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All calls to mips_cpc_lock_other should be wrapped in
mips_cm_lock_other. This only matters if the system has CM3 and is using
cpu idle, since otherwise a) the CPC lock is sufficent for CM < 3 and b)
any systems with CM > 3 have not been able to use cpu idle until now.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/14227/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS CM3 changed the management of coherence. Instead of a coherence
control register with a bitmask of coherent domains, CM3 simply has a
coherence enable register with a single bit to enable coherence of the
local core. Support this by clearing and setting this single bit to
disable / enable coherence.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14226/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for CPUs implementing the MIPSr6 ISA to the CPS
power management code. Three changes are necessary:
1. In MIPSr6, coupled coherence is necessary when CPUS implement multiple
Virtual Processors (VPs).
2. MIPSr6 virtual processors are more like real cores and cannot yield
to other VPs on the same core, so drop the MT ASE yield instruction.
3. To halt a MIPSr6 VP, the CPC VP_STOP register is used rather than the
MT ASE TCHalt CP0 register.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14225/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of selecting an implementation or vendor specific sync type for
the required sync operations, always use the architecturally mandated
sync types which previous patches have put in place. The selection of
special sync types is now redundant an can be removed.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14223/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
SYNC type 0 is defined in the MIPS architecture as a completion barrier
where all loads/stores in the pipeline before the sync instruction must
complete before any loads/stores subsequent to the sync instruction.
In places where we require loads / stores be globally completed, use the
standard completion sync stype.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14224/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since R2 of the MIPS architecture, SYNC(0x10) has been an optional but
architecturally defined ordering barrier. If a CPU does not implement it,
the arch specifies that it must fall back to SYNC(0).
In places where we require that the instruction stream not be reordered,
but do not require that loads / stores are gloablly completed, use the
defined standard sync stype.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14221/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the definitions of sync stype 0 (global completion barrier) and sync
stype 0x10 (local ordering barrier) to barrier.h for use with the sync
instruction.
These types are defined by the MIPS Instruction Set since R2 of the
architecture and are documented in document MD00087 table 6.5.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14222/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This code makes large use of barriers, which had quite vague
descriptions. Update the comments to make the choice of barrier and
reason for it more clear.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14220/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The check for whether a CPU required the FSB flush workaround
previously required every CPU not requiring it to be whitelisted. That
approach does not scale well as new CPUs are introduced so change the
default from a WARN and returning an error to just returning 0. Any CPUs
requiring the workaround can then be added to the blacklist.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14218/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MIPS CM version 3 removed the CPC_CL_OTHER register and instead the
CM_CL_OTHER register is used to redirect the CPC_OTHER region. As such,
we should not write the unimplmented register and can avoid the
spinlock as well.
These lock functions should aleady be called within the context of a
mips_cm_{lock,unlock}_other pair ensuring the correct CPC_OTHER region
will be accessed.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14219/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
PHY access through the board helper is impossible with the
current drivers, so delete this code.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14205/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Delete legacy hack for broken bootloaders. The warning has been in kernel
for several years, and if there are still users using such bootloaders,
they can fix the boot by supplying a proper DTB.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14201/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes creating a fake pci device in MIPS early config
access and instead just uses the pci bus to get the same functionality.
The struct pci_dev is too large to allocate on the stack, and was relying
on compiler optimizations to remove its usage.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14253/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the custom minimal clock implementation for Toshiba TXx9 by a
basic implementation using the Common Clock Framework.
The only clocks that are provided are those needed by TXx9-specific
drivers ("imbus" and "spi" (TX4938 only)), and their common parent
clock "gbus". Other clocks can be added when needed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-clk@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-watchdog@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14239/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
txx9_gpio_init() calls gpiochip_add_data(), which fails with -ENOMEM as
it is called too early in the boot process. This causes all subsequent
GPIO operations to fail silently (before commit 54d77198fd ("gpio:
bail out silently on NULL descriptors") it printed the error message
"gpiod_direction_output_raw: invalid GPIO" on RBTX49[23]7).
Postpone all GPIO setup to .arch_init() time to fix this.
Suggested-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14237/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
txx9_gpio_init() calls gpiochip_add_data(), which fails with -ENOMEM as
it is called too early in the boot process. This causes all subsequent
GPIO operations to fail silently.
Postpone all GPIO setup to .arch_init() time to fix this.
Suggested-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: linux-gpio@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13967/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
In the case of traps.c we can't dump the module.h include since it is
also used to provide "print_modules".
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13934/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Kconfig currently controlling compilation of this code is:
arch/mips/lantiq/Kconfig:config XRX200_PHY_FW
arch/mips/lantiq/Kconfig: bool "XRX200 PHY firmware loader"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We don't replace module.h with init.h since the file doesn't need that.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13932/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Makefile entry controlling compilation of this code is:
arch/mips/lantiq/xway/vmmc.o
---> arch/mips/lantiq/xway/Makefile:obj-y += vmmc.o
...meaning that it currently is not being built as a module by anyone.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We replace module.h with export.h since the file does actually use
EXPORT_SYMBOL.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13930/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Makefile entry controlling compilation of this code is "obj-y"
meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13931/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Makefile entry controlling compilation of this code is "obj-y"
meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: "Rafał Miłecki" <zajec5@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13933/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 7eb8c99db2 ("MIPS: Delete smp-gic.c") removed the file from the
Makefile and the option to build it from KConfig, but left the file
itself floating in the tree.
Remove the unused source file.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: paul.burton@imgtec.com
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13883/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The addition of VPE information to /proc/cpuinfo used to be in smp-mt.c.
This file is not used by MIPS r6 kernels, so the Virtual Processor
information was not present for these CPU types.
Move the code to print VPE information into proc.c, add a case for MIPS
r6 CPUS, and remove the block from smp-mt.c.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Zubair Lutfullah Kakakhel <Zubair.Kakakhel@imgtec.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Take all memory into use by default, instead of limiting to 512 MB.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Sivasubramanian Palanisamy <sivasubramanian.palanisamy@nokia.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13353/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Only one defconfig has a STACKPROTECTOR value. And it asks for
the strong variant, which isn't supported by older toolchains.
Due to the nature of MIPS having more platform specific code than say
x86, the allyesconfig and allmodconfig aren't as effective for build
coverage. So, in addition, I like to use a trivial script to walk all
the defconfigs and build each one.
However I will get false positives on unsupported stackprotector values
with an older toolchain like gcc-4.6.3. As in this instance I am just
using the compiler as a glorified syntax checker on a machine where I
build a bunch of other arch for the same reason, there is no real
motivation to get a newer toolchain for improved optimization etc.
Since there is only one of them, and there is nothing about these
settings that are board/platform specific, I propose we just eliminate
the existing instance and take the default.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: James Hartley <james.hartley@imgtec.com>
Cc: Ionela Voinescu <ionela.voinescu@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull CPU hotplug updates from Thomas Gleixner:
"Yet another batch of cpu hotplug core updates and conversions:
- Provide core infrastructure for multi instance drivers so the
drivers do not have to keep custom lists.
- Convert custom lists to the new infrastructure. The block-mq custom
list conversion comes through the block tree and makes the diffstat
tip over to more lines removed than added.
- Handle unbalanced hotplug enable/disable calls more gracefully.
- Remove the obsolete CPU_STARTING/DYING notifier support.
- Convert another batch of notifier users.
The relayfs changes which conflicted with the conversion have been
shipped to me by Andrew.
The remaining lot is targeted for 4.10 so that we finally can remove
the rest of the notifiers"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (46 commits)
cpufreq: Fix up conversion to hotplug state machine
blk/mq: Reserve hotplug states for block multiqueue
x86/apic/uv: Convert to hotplug state machine
s390/mm/pfault: Convert to hotplug state machine
mips/loongson/smp: Convert to hotplug state machine
mips/octeon/smp: Convert to hotplug state machine
fault-injection/cpu: Convert to hotplug state machine
padata: Convert to hotplug state machine
cpufreq: Convert to hotplug state machine
ACPI/processor: Convert to hotplug state machine
virtio scsi: Convert to hotplug state machine
oprofile/timer: Convert to hotplug state machine
block/softirq: Convert to hotplug state machine
lib/irq_poll: Convert to hotplug state machine
x86/microcode: Convert to hotplug state machine
sh/SH-X3 SMP: Convert to hotplug state machine
ia64/mca: Convert to hotplug state machine
ARM/OMAP/wakeupgen: Convert to hotplug state machine
ARM/shmobile: Convert to hotplug state machine
arm64/FP/SIMD: Convert to hotplug state machine
...
Pull low-level x86 updates from Ingo Molnar:
"In this cycle this topic tree has become one of those 'super topics'
that accumulated a lot of changes:
- Add CONFIG_VMAP_STACK=y support to the core kernel and enable it on
x86 - preceded by an array of changes. v4.8 saw preparatory changes
in this area already - this is the rest of the work. Includes the
thread stack caching performance optimization. (Andy Lutomirski)
- switch_to() cleanups and all around enhancements. (Brian Gerst)
- A large number of dumpstack infrastructure enhancements and an
unwinder abstraction. The secret long term plan is safe(r) live
patching plus maybe another attempt at debuginfo based unwinding -
but all these current bits are standalone enhancements in a frame
pointer based debug environment as well. (Josh Poimboeuf)
- More __ro_after_init and const annotations. (Kees Cook)
- Enable KASLR for the vmemmap memory region. (Thomas Garnier)"
[ The virtually mapped stack changes are pretty fundamental, and not
x86-specific per se, even if they are only used on x86 right now. ]
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
x86/asm: Get rid of __read_cr4_safe()
thread_info: Use unsigned long for flags
x86/alternatives: Add stack frame dependency to alternative_call_2()
x86/dumpstack: Fix show_stack() task pointer regression
x86/dumpstack: Remove dump_trace() and related callbacks
x86/dumpstack: Convert show_trace_log_lvl() to use the new unwinder
oprofile/x86: Convert x86_backtrace() to use the new unwinder
x86/stacktrace: Convert save_stack_trace_*() to use the new unwinder
perf/x86: Convert perf_callchain_kernel() to use the new unwinder
x86/unwind: Add new unwind interface and implementations
x86/dumpstack: Remove NULL task pointer convention
fork: Optimize task creation by caching two thread stacks per CPU if CONFIG_VMAP_STACK=y
sched/core: Free the stack early if CONFIG_THREAD_INFO_IN_TASK
lib/syscall: Pin the task stack in collect_syscall()
x86/process: Pin the target stack in get_wchan()
x86/dumpstack: Pin the target stack when dumping it
kthread: Pin the stack via try_get_task_stack()/put_task_stack() in to_live_kthread() function
sched/core: Add try_get_task_stack() and put_task_stack()
x86/entry/64: Fix a minor comment rebase error
iommu/amd: Don't put completion-wait semaphore on stack
...
When discovering the number of VPEs per core, smp_num_siblings will be
incorrect for kernels built without support for the MIPS MultiThreading
(MT) ASE running on systems which implement said ASE. This leads to
accesses to VPEs in secondary cores being performed incorrectly since
mips_cm_vp_id calculates the wrong ID to write to the local "other"
registers. Fix this by examining the number of VPEs in the core as
reported by the CM.
This patch presumes that the number of VPEs will be the same in each
core of the system. As this path only applies to systems with CM version
2.5 or lower, and this property is true of all such known systems, this
is likely to be fine but is described in a comment for good measure.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14338/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The paging_init() function contains code which detects that highmem is
in use but unsupported due to dcache aliasing. However this code was
ineffective because it was being run before the caches are probed,
meaning that cpu_has_dc_aliases would always evaluate to false (unless a
platform overrides it to a compile-time constant) and the detection of
the unsupported case is never triggered. The kernel would then go on to
attempt to use highmem & either hit coherency issues or trigger the
BUG_ON in flush_kernel_dcache_page().
Fix this by running paging_init() later than cpu_cache_init(), such that
the cpu_has_dc_aliases macro will evaluate correctly & the unsupported
highmem case will be detected successfully.
This then leads to a formerly hidden issue in that
mem_init_free_highmem() will attempt to free all highmem pages, even
though we're avoiding use of them & don't have valid page structs for
them. This leads to an invalid pointer dereference & a TLB exception.
Avoid this by skipping the loop in mem_init_free_highmem() if
cpu_has_dc_aliases evaluates true.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Rabin Vincent <rabinv@axis.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14184/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Malta boards used with CPU emulators feature a switch to disable use of
an IOCU. Software has to check this switch & ignore any present IOCU if
the switch is closed. The read used to do this was unsafe for 64 bit
kernels, as it simply casted the address 0xbf403000 to a pointer &
dereferenced it. Whilst in a 32 bit kernel this would access kseg1, in a
64 bit kernel this attempts to access xuseg & results in an address
error exception.
Fix by accessing a correctly formed ckseg1 address generated using the
CKSEG1ADDR macro.
Whilst modifying this code, define the name of the register and the bit
we care about within it, which indicates whether PCI DMA is routed to
the IOCU or straight to DRAM. The code previously checked that bit 0 was
also set, but the least significant 7 bits of the CONFIG_GEN0 register
contain the value of the MReqInfo signal provided to the IOCU OCP bus,
so singling out bit 0 makes little sense & that part of the check is
dropped.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: b6d92b4a6b ("MIPS: Add option to disable software I/O coherency.")
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14187/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When the kernel is built for microMIPS, branches targets need to be
known to be microMIPS code in order to result in bit 0 of the PC being
set. The branch target in the BUILD_ROLLBACK_PROLOGUE macro was simply
the end of the macro, which may be pointing at padding rather than at
code. This results in recent enough GNU linkers complaining like so:
mips-img-linux-gnu-ld: arch/mips/built-in.o: .text+0x3e3c: Unsupported branch between ISA modes.
mips-img-linux-gnu-ld: final link failed: Bad value
Makefile:936: recipe for target 'vmlinux' failed
make: *** [vmlinux] Error 1
Fix this by changing the branch target to be the start of the
appropriate handler, skipping over any padding.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14019/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On current P-series cores from Imagination the FTLB can be enabled or
disabled via a bit in the Config6 register, and an execution hazard is
created by changing the value of bit. The ftlb_disable function already
cleared that hazard but that does no good for other callers. Clear the
hazard in the set_ftlb_enable function that creates it, and only for the
cores where it applies.
This has the effect of reverting c982c6d6c4 ("MIPS: cpu-probe: Remove
cp0 hazard barrier when enabling the FTLB") which was incorrect.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: c982c6d6c4 ("MIPS: cpu-probe: Remove cp0 hazard barrier when enabling the FTLB")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14023/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On some cores (proAptiv, P5600) we make use of the sizes of the TLBs
to determine the desired FTLB:VTLB write ratio. However set_ftlb_enable
& thus calculate_ftlb_probability is called before decode_config4. This
results in us calculating a probability based on zero sizes, and we end
up setting FTLBP=3 for a 3:1 FTLB:VTLB write ratio in all cases. This
will make abysmal use of the available FTLB resources in the affected
cores.
Fix this by configuring the FTLB probability after having decoded
config4. However we do need to have enabled the FTLB before that point
such that fields in config4 actually reflect that an FTLB is present. So
set_ftlb_enable is now called twice, with flags indicating that it
should configure the write probability only the second time.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: cf0a8aa022 ("MIPS: cpu-probe: Set the FTLB probability bit on supported cores")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14022/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The FTLBP field in Config7 for the I6400 is intended as chicken bits for
debugging rather than as a field that software actually makes use of.
For best performance, FTLBP should be left at its default value of 0
with all TLB writes hitting the FTLB by default.
Additionally, since set_ftlb_enable is called from decode_configs before
decode_config4 which determines the size of the TLBs, this was
previously always setting FTLBP=3 for a 3:1 FTLB:VTLB write ratio which
makes abysmal use of the available FTLB resources.
This effectively reverts b0c4e1b79d8a ("MIPS: Set up FTLB probability
for I6400").
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: b0c4e1b79d8a ("MIPS: Set up FTLB probability for I6400")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14021/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When expanding the la or dla pseudo-instruction in a delay slot the GNU
assembler will complain should the pseudo-instruction expand to multiple
actual instructions, since only the first of them will be in the delay
slot leading to the pseudo-instruction being only partially executed if
the branch is taken. Use of PTR_LA in the dec int-handler.S leads to
such warnings:
arch/mips/dec/int-handler.S: Assembler messages:
arch/mips/dec/int-handler.S:149: Warning: macro instruction expanded into multiple instructions in a branch delay slot
arch/mips/dec/int-handler.S:198: Warning: macro instruction expanded into multiple instructions in a branch delay slot
Avoid this by open coding the PTR_LA macros.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We clear the OF_POPULATED flag for the GPIO controller node on Octeon
processors. Otherwise, none of the devices hanging on the GPIO lines
are probed. The 'gpio-leds' driver on OCTEON failed to probe in addition
to other devices on Cavium 71xx and 78xx development boards.
Fixes: 15cc2ed6dc ("of/irq: Mark initialised interrupt controllers as populated")
Signed-off-by: Steven J. Hill <steven.hill@cavium.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: David Daney <david.daney@cavium.com>
Cc: Rob Herring <robh@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14091/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch_uprobe_pre_xol needs to emulate a branch if a branch instruction
has been replaced with a breakpoint, but in fact an uninitialised local
variable was passed to the emulator routine instead of the original
instruction
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Fixes: 40e084a506 ('MIPS: Add uprobes support.')
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14300/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Generic kernel code implements a weak version of set_orig_insn that
moves cached 'insn' from arch_uprobe to the original code location when
the trap is removed.
MIPS variant used arch_uprobe->orig_inst which was never initialised
properly, so this code only inserted a nop instead of the original
instruction. With that change orig_inst can also be safely removed.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Fixes: 40e084a506 ('MIPS: Add uprobes support.')
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14299/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch_uretprobe_hijack_return_addr should replace the return address for
a call with a trampoline address.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Fixes: 40e084a506 ('MIPS: Add uprobes support.')
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14298/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 0d2808f338 ("MIPS: smp-cps: Add support for CPU hotplug of
MIPSr6 processors") added a call to mips_cm_lock_other in order to lock
the CPC in CPUs containing a version 3 or higher Coherence Manager,
which use the general CM core other register, where previous CMs had a
dedicated core other register for the CPC.
A kernel BUG() is triggered, however, if mips_cm_lock_other is called
with a VP other than 0 on a CPU with CM < 3, a condition introduced by
0d2808f338.
Avoid the BUG() by always locking VP0 when locking the CPC, since the
required register, cpc_stat_conf, is shared by all vps in a core.
Fixes: 0d2808f338 ("MIPS: smp-cps: Add support for CPU hotplug...)
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Qais Yousef <qsyousef@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14297/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There exists a slightly dubious optimisation in the implementation of
the MIPS KVM EntryHi emulation which skips TLB invalidation if the
EntryHi points to an address in the guest KSeg0 region, intended to
catch guest TLB invalidations where the ASID is almost immediately
restored to the previous value.
Now that we perform lazy host ASID regeneration for guest user mode when
the guest ASID changes we should be able to drop the optimisation
without a significant impact (only the extra TLB refills for the small
amount of code while the TLB is being invalidated).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Invalidate host TLB mappings when the guest ASID is changed by
regenerating ASIDs, rather than flushing the entire host TLB except
entries in the guest KSeg0 range.
For the guest kernel mode ASID we regenerate on the spot when the guest
ASID is changed, as that will always take place while the guest is in
kernel mode.
However when the guest invalidates TLB entries the ASID will often by
changed temporarily as part of writing EntryHi without the guest
returning to user mode in between. We therefore regenerate the user mode
ASID lazily before entering the guest in user mode, if and only if the
guest ASID has actually changed since the last guest user mode entry.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
The host ASIDs for guest kernel and user mode are regenerated together
if the ASID for guest kernel mode is out of date. That is fine as the
ASID for guest kernel mode is always generated first, however it doesn't
allow the ASIDs to be regenerated or invalidated individually instead of
linearly flushing the entire host TLB.
Therefore separate the regeneration code so that the ASIDs are checked
and regenerated separately.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
When a guest TLB entry is replaced by TLBWI or TLBWR, we only invalidate
TLB entries on the local CPU. This doesn't work correctly on an SMP host
when the guest is migrated to a different physical CPU, as it could pick
up stale TLB mappings from the last time the vCPU ran on that physical
CPU.
Therefore invalidate both user and kernel host ASIDs on other CPUs,
which will cause new ASIDs to be generated when it next runs on those
CPUs.
We're careful only to do this if the TLB entry was already valid, and
only for the kernel ASID where the virtual address it mapped is outside
of the guest user address range.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Commit 432c6bacbd ("MIPS: Use per-mm page to execute branch delay slot
instructions") accidentally removed use of the MIPS_FPU_EMU_INC_STATS
macro from do_dsemulret, leading to the ds_emul file in debugfs always
returning zero even though we perform delay slot emulations.
Fix this by re-adding the use of the MIPS_FPU_EMU_INC_STATS macro.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: 432c6bacbd ("MIPS: Use per-mm page to execute branch delay slot instructions")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14301/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the possibility of a deadlock when bringing up
secondary CPUs.
The deadlock occurs because the set_cpu_online() is called before
synchronise_count_slave(). This can cause a deadlock if the boot CPU,
having scheduled another thread, attempts to send an IPI to the
secondary CPU, which it sees has been marked online. The secondary is
blocked in synchronise_count_slave() waiting for the boot CPU to enter
synchronise_count_master(), but the boot cpu is blocked in
smp_call_function_many() waiting for the secondary to respond to it's
IPI request.
Fix this by marking the CPU online in cpu_callin_map and synchronising
counters before declaring the CPU online and calculating the maps for
IPIs.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reported-by: Justin Chen <justinpopo6@gmail.com>
Tested-by: Justin Chen <justinpopo6@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: stable@vger.kernel.org # v4.1+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14302/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the mipsr2_decoder() function, used to emulate pre-MIPSr6
instructions that were removed in MIPSr6, the init_fpu() function is
called if a removed pre-MIPSr6 floating point instruction is the first
floating point instruction used by the task. However, init_fpu()
performs varous actions that rely upon not being migrated. For example
in the most basic case it sets the coprocessor 0 Status.CU1 bit to
enable the FPU & then loads FP register context into the FPU registers.
If the task were to migrate during this time, it may end up attempting
to load FP register context on a different CPU where it hasn't set the
CU1 bit, leading to errors such as:
do_cpu invoked from kernel context![#2]:
CPU: 2 PID: 7338 Comm: fp-prctl Tainted: G D 4.7.0-00424-g49b0c82 #2
task: 838e4000 ti: 88d38000 task.ti: 88d38000
$ 0 : 00000000 00000001 ffffffff 88d3fef8
$ 4 : 838e4000 88d38004 00000000 00000001
$ 8 : 3400fc01 801f8020 808e9100 24000000
$12 : dbffffff 807b69d8 807b0000 00000000
$16 : 00000000 80786150 00400fc4 809c0398
$20 : 809c0338 0040273c 88d3ff28 808e9d30
$24 : 808e9d30 00400fb4
$28 : 88d38000 88d3fe88 00000000 8011a2ac
Hi : 0040273c
Lo : 88d3ff28
epc : 80114178 _restore_fp+0x10/0xa0
ra : 8011a2ac mipsr2_decoder+0xd5c/0x1660
Status: 1400fc03 KERNEL EXL IE
Cause : 1080002c (ExcCode 0b)
PrId : 0001a920 (MIPS I6400)
Modules linked in:
Process fp-prctl (pid: 7338, threadinfo=88d38000, task=838e4000, tls=766527d0)
Stack : 00000000 00000000 00000000 88d3fe98 00000000 00000000 809c0398 809c0338
808e9100 00000000 88d3ff28 00400fc4 00400fc4 0040273c 7fb69e18 004a0000
004a0000 004a0000 7664add0 8010de18 00000000 00000000 88d3fef8 88d3ff28
808e9100 00000000 766527d0 8010e534 000c0000 85755000 8181d580 00000000
00000000 00000000 004a0000 00000000 766527d0 7fb69e18 004a0000 80105c20
...
Call Trace:
[<80114178>] _restore_fp+0x10/0xa0
[<8011a2ac>] mipsr2_decoder+0xd5c/0x1660
[<8010de18>] do_ri+0x90/0x6b8
[<80105c20>] ret_from_exception+0x0/0x10
Fix this by disabling preemption around the call to init_fpu(), ensuring
that it starts & completes on one CPU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Fixes: b0a668fb20 ("MIPS: kernel: mips-r2-to-r6-emul: Add R2 emulator for MIPS R6")
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.0+
Patchwork: https://patchwork.linux-mips.org/patch/14305/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The page structures associated with the vDSO pages in the kernel image
are calculated using virt_to_page(), which uses __pa() under the hood to
find the pfn associated with the virtual address. The vDSO data pointers
however point to kernel symbols, so __pa_symbol() should really be used
instead.
Since there is no equivalent to virt_to_page() which uses __pa_symbol(),
fix init_vdso_image() to work directly with pfns, calculated with
__phys_to_pfn(__pa_symbol(...)).
This issue broke the Malta Enhanced Virtual Addressing (EVA)
configuration which has a non-default implementation of __pa_symbol().
This is because it uses a physical alias so that the kernel executes
from KSeg0 (VA 0x80000000 -> PA 0x00000000), while RAM is provided to
the kernel in the KUSeg range (VA 0x00000000 -> PA 0x80000000) which
uses the same underlying RAM.
Since there are no page structures associated with the low physical
address region, some arbitrary kernel memory would be interpreted as a
page structure for the vDSO pages and badness ensues.
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: <stable@vger.kernel.org> # 4.4.x-
Patchwork: https://patchwork.linux-mips.org/patch/14229/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Install the callbacks via the state machine.
[ tglx: Renamed the state to MIPS_SOC_PREPARE so it can be reused by other
SOCs ]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160906170457.32393-16-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add lost Kconfig symbol. This should have been part of 40e084a506
('MIPS: Add uprobes support.').
Fixes: 40e084a506 ('MIPS: Add uprobes support.')
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 44a7185c2a ("of/platform: Add common method to populate
default bus") added new arch_initcall of_platform_default_populate_init()
that will override device_initcall octeon_publish_devices(). This broke
many OCTEON boards as important devices are not getting probed anymore
(e.g. on EdgeRouter Lite the USB mass storage/rootfs is missing).
Fix by changing octeon_publish_devices() to arch_initcall.
Fixes: 44a7185c2a ("of/platform: Add common method to populate default bus")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Rob Herring <robh@kernel.org>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14041/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 1685ddbe35 ("MIPS: Octeon: Changes to support readq()/writeq()
usage.") added bitwise shift operations that assume that unsigned long
is always 64-bits. This broke the build of VDSO code, as it gets compiled
also in "faked" 32-bit mode. Althought the failing inline functions are
never executed in 32-bit mode, they still need to pass the compilation.
Fix by using 64-bit types explicitly.
The patch fixes the following build failure:
CC arch/mips/vdso/gettimeofday-o32.o
In file included from los/git/devel/linux/arch/mips/include/asm/io.h:32:0,
from los/git/devel/linux/arch/mips/include/asm/page.h:194,
from los/git/devel/linux/arch/mips/vdso/vdso.h:26,
from los/git/devel/linux/arch/mips/vdso/gettimeofday.c:11:
los/git/devel/linux/arch/mips/include/asm/mach-cavium-octeon/mangle-port.h: In function '__should_swizzle_bits':
los/git/devel/linux/arch/mips/include/asm/mach-cavium-octeon/mangle-port.h:19:40: error: right shift count >= width of type [-Werror=shift-count-overflow]
unsigned long did = ((unsigned long)a >> 40) & 0xff;
^~
Fixes: 1685ddbe35 ("MIPS: Octeon: Changes to support readq()/writeq() usage.")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <ddaney@caviumnetworks.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Steven J. Hill <steven.hill@cavium.com>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14039/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
cpu_has_fpu macro uses smp_processor_id() and is currently executed
with preemption enabled, that triggers the warning at runtime.
It is assumed throughout the kernel that if any CPU has an FPU, then all
CPUs would have an FPU as well, so it is safe to perform the check with
preemption enabled - change the code to use raw_ variant of the check to
avoid the warning.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 4.0+
Patchwork: https://patchwork.linux-mips.org/patch/14125/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Two stubs are added:
o kvm_arch_has_vcpu_debugfs(): must return true if the arch
supports creating debugfs entries in the vcpu debugfs dir
(which will be implemented by the next commit)
o kvm_arch_create_vcpu_debugfs(): code that creates debugfs
entries in the vcpu debugfs dir
For x86, this commit introduces a new file to avoid growing
arch/x86/kvm/x86.c even more.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull uaccess fixes from Al Viro:
"Fixes for broken uaccess primitives - mostly lack of proper zeroing
in copy_from_user()/get_user()/__get_user(), but for several
architectures there's more (broken clear_user() on frv and
strncpy_from_user() on hexagon)"
* 'uaccess-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (28 commits)
avr32: fix copy_from_user()
microblaze: fix __get_user()
microblaze: fix copy_from_user()
m32r: fix __get_user()
blackfin: fix copy_from_user()
sparc32: fix copy_from_user()
sh: fix copy_from_user()
sh64: failing __get_user() should zero
score: fix copy_from_user() and friends
score: fix __get_user/get_user
s390: get_user() should zero on failure
ppc32: fix copy_from_user()
parisc: fix copy_from_user()
openrisc: fix copy_from_user()
nios2: fix __get_user()
nios2: copy_from_user() should zero the tail of destination
mn10300: copy_from_user() should zero on access_ok() failure...
mn10300: failing __get_user() and get_user() should zero
mips: copy_from_user() must zero the destination on access_ok() failure
ARC: uaccess: get_user to zero out dest in cause of fault
...
Commit f70ddc07b6 ("MIPS: c-r4k: Avoid small flush_icache_range SMP
calls") adds checks to force use of hit-type cache ops for small icache
flushes where they are globalised & index-type cache ops aren't, in
order to avoid the overhead of IPIs in those cases. However it
calculated the size of the region being flushed incorrectly, subtracting
the end address from the start address rather than the reverse. This
would have led to an overflow with size wrapping round to some large
value, and likely to the special case for avoiding IPIs not actually
being hit.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Fixes: f70ddc07b6 ("MIPS: c-r4k: Avoid small flush_icache_range SMP calls")
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14211/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If the paravirt machine is compiles without CONFIG_SMP, the following
linker error occurs
arch/mips/kernel/head.o: In function `kernel_entry':
(.ref.text+0x10): undefined reference to `smp_bootstrap'
due to the kernel entry macro always including SMP startup code.
Wrap this code in CONFIG_SMP to fix the error.
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: stable@vger.kernel.org # 3.16+
Patchwork: https://patchwork.linux-mips.org/patch/14212/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Paul Mackerras writes:
The highlights are:
* Reduced latency for interrupts from PCI pass-through devices, from
Suresh Warrier and me.
* Halt-polling implementation from Suraj Jitindar Singh.
* 64-bit VCPU statistics, also from Suraj.
* Various other minor fixes and improvements.
Commit c1a0e9bc88 ("MIPS: Allow compact branch policy to be changed")
added Kconfig entries allowing for the compact branch policy used by the
compiler for MIPSr6 kernels to be specified. This can be useful for
debugging, particularly in systems where compact branches have recently
been introduced.
Unfortunately mainline gcc 5.x supports MIPSr6 but not the
-mcompact-branches compiler flag, leading to MIPSr6 kernels failing to
build with gcc 5.x with errors such as:
mipsel-linux-gnu-gcc: error: unrecognized command line option '-mcompact-branches=optimal'
make[2]: *** [kernel/bounds.s] Error 1
Fixing this by hiding the Kconfig entry behind another seems to be more
hassle than it's worth, as MIPSr6 & compact branches have been around
for a while now and if policy does need to be set for debug it can be
done easily enough with KCFLAGS. Therefore remove the compact branch
policy Kconfig entries & their handling in the Makefile.
This reverts commit c1a0e9bc88 ("MIPS: Allow compact branch policy to
be changed").
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: c1a0e9bc88 ("MIPS: Allow compact branch policy to be changed")
Cc: stable <stable@vger.kernel.org> # v4.4+
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14241/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The alignment of MIPS MAAR region addresses isn't quite right.
- It rounds an already 64 KiB aligned start address up to the next
64 KiB boundary, e.g. 0x80000000 is rounded up to 0x80010000.
- It assumes the end address is already on a 64 KiB boundary and doesn't
round it down. Should that not be the case it will hit the second
BUG_ON() in write_maar_pair().
Both cases are addressed by rounding up and down to 64 KiB boundaries in
the more traditional way of adding 0xffff (for rounding up) and masking
off the low 16 bits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13858/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Memory regions added with add_memory_region() at the top of the physical
address space will have their end address overflow to 0. This causes
them to be rejected as invalid, and would cause various other issues
later on.
This causes issues on Malta and Boston platforms when wanting to use all
2GB of RAM on a 32-bit kernel, either via highmem (using physical
addresses 0x90000000..0xFFFFFFFF), or with the Malta Enhanced Virtual
Addressing (EVA) layout which exposes the whole 0x80000000..0xFFFFFFFF
physical address range to kernel mode at 0x00000000..0x7FFFFFFF.
Due to the abundance of these non-overflow assumptions and the fact that
memblock already avoids the arithmetic overflow by limiting the size of
new memory regions without the arch code knowing it (in particular
mem_init_free_highmem() will trigger a page dump due to nonzero mapcount
on the last page), it is simpler and safer to just limit the size of the
region in a similar way to memblock but at the arch level to allow most
of the RAM to be used without arithmetic overflows.
Therefore we detect this case specifically and reduce the size of the
region slightly to avoid the arithmetic overflows and cause the last
page to be ignored.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13857/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a uprobe-replacement breakpoint instruction is handled, a notifier
is called with DIE_UPROBE argument, but a corresponding exception notify
handler for MIPS attempts to handle DIE_BREAK instead. As a result
the breakpoint instruction isn't handled by the uprobe code and the probed
application terminates with SIGTRAP.
Fix this by changing arch_uprobe_exception_notify code to handle
DIE_UPROBE as a pre-singlestep condition instead of DIE_BREAK.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
clk_register_fixed_factor returns an ERR_PTR in case of an error and
should have an IS_ERR check instead of a null check.
The Coccinelle semantic patch used to find this issue is as follows:
@@
expression e;
statement S;
@@
*e = clk_register_fixed_factor(...);
if (!e) S
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Cc: julia.lawall@lip6.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13894/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds two new system calls:
int pkey_alloc(unsigned long flags, unsigned long init_access_rights)
int pkey_free(int pkey);
These implement an "allocator" for the protection keys
themselves, which can be thought of as analogous to the allocator
that the kernel has for file descriptors. The kernel tracks
which numbers are in use, and only allows operations on keys that
are valid. A key which was not obtained by pkey_alloc() may not,
for instance, be passed to pkey_mprotect().
These system calls are also very important given the kernel's use
of pkeys to implement execute-only support. These help ensure
that userspace can never assume that it has control of a key
unless it first asks the kernel. The kernel does not promise to
preserve PKRU (right register) contents except for allocated
pkeys.
The 'init_access_rights' argument to pkey_alloc() specifies the
rights that will be established for the returned pkey. For
instance:
pkey = pkey_alloc(flags, PKEY_DENY_WRITE);
will allocate 'pkey', but also sets the bits in PKRU[1] such that
writing to 'pkey' is already denied.
The kernel does not prevent pkey_free() from successfully freeing
in-use pkeys (those still assigned to a memory range by
pkey_mprotect()). It would be expensive to implement the checks
for this, so we instead say, "Just don't do it" since sane
software will never do it anyway.
Any piece of userspace calling pkey_alloc() needs to be prepared
for it to fail. Why? pkey_alloc() returns the same error code
(ENOSPC) when there are no pkeys and when pkeys are unsupported.
They can be unsupported for a whole host of reasons, so apps must
be prepared for this. Also, libraries or LD_PRELOADs might steal
keys before an application gets access to them.
This allocation mechanism could be implemented in userspace.
Even if we did it in userspace, we would still need additional
user/kernel interfaces to tell userspace which keys are being
used by the kernel internally (such as for execute-only
mappings). Having the kernel provide this facility completely
removes the need for these additional interfaces, or having an
implementation of this in userspace at all.
Note that we have to make changes to all of the architectures
that do not use mman-common.h because we use the new
PKEY_DENY_ACCESS/WRITE macros in arch-independent code.
1. PKRU is the Protection Key Rights User register. It is a
usermode-accessible register that controls whether writes
and/or access to each individual pkey is allowed or denied.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Mel Gorman <mgorman@techsingularity.net>
Cc: linux-arch@vger.kernel.org
Cc: Dave Hansen <dave@sr71.net>
Cc: arnd@arndb.de
Cc: linux-api@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: luto@kernel.org
Cc: akpm@linux-foundation.org
Cc: torvalds@linux-foundation.org
Link: http://lkml.kernel.org/r/20160729163015.444FE75F@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
MIPS Enhanced Virtual Addressing (EVA) allows the virtual memory
segments to be rearranged such that the KSeg0/KSeg1 segments are
accessible TLB mapped to user mode, which would trigger a TLB Miss
exception (due to lack of TLB mappings) instead of an Address Error
exception.
Update the TLB Miss handling similar to Address Error handling for guest
MMIO emulation.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
MIPS Enhanced Virtual Addressing (EVA) allows the user mode and kernel
mode address spaces to overlap, breaking the assumption that PAGE_OFFSET
is an appropriate KVM HVA error value, since PAGE_OFFSET may be as low
as zero.
Fix this in the same way that s390 does in commit bf640876e2 ("KVM:
s390: Make KVM_HVA_ERR_BAD usable on s390"), by overriding
KVM_HVA_ERR_[RO_]BAD and kvm_is_error_hva() in asm/kvm_host.h.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
vms and vcpus have statistics associated with them which can be viewed
within the debugfs. Currently it is assumed within the vcpu_stat_get() and
vm_stat_get() functions that all of these statistics are represented as
u32s, however the next patch adds some u64 vcpu statistics.
Change all vcpu statistics to u64 and modify vcpu_stat_get() accordingly.
Since vcpu statistics are per vcpu, they will only be updated by a single
vcpu at a time so this shouldn't present a problem on 32-bit machines
which can't atomically increment 64-bit numbers. However vm statistics
could potentially be updated by multiple vcpus from that vm at a time.
To avoid the overhead of atomics make all vm statistics ulong such that
they are 64-bit on 64-bit systems where they can be atomically incremented
and are 32-bit on 32-bit systems which may not be able to atomically
increment 64-bit numbers. Modify vm_stat_get() to expect ulongs.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
** fixes for ITS init issues, error handling, IRQ leakage, race conditions
** An erratum workaround for timers
** Some removal of misleading use of errors and comments
** A fix for GICv3 on 32-bit guests
* MIPS fix where the guest could wrongly map the first page of physical memory
* x86 nested virtualization fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXtyfVAAoJEL/70l94x66Dhe4IAIOGI/OYVWU5IfUQ01oeRgD3
7wN222OmyC/K0/hSZc7ndRdcQfr5ombgM9XsS/EbkcRacWxAUHDX2FaYMpKgjT2M
Dnh2tJHuPz/4VtByGQ2fZ4hziK7amn18/MtPFCee+mIj0ya2fcWZ4qHVU8pKC6Ps
mVVZ0kxXsdV4pw9y6XgBLz/4bTLeASKvhFZrWOnjJoa+GeH2MFwocS0xaEI0HwxP
HVwcgoRdGXJuKUB9jE9FDWmWOgdoLnCG1bNUOvXKPcE0ZaFQDT4I4dImkBys3rqz
jbqnhLrpGEY2ZC3Rj+VyD2MOXbYOOSi59GRwYmCkqD96ZarHxSu3PdyCxmIFWzM=
=+4WK
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"ARM:
- fixes for ITS init issues, error handling, IRQ leakage, race
conditions
- an erratum workaround for timers
- some removal of misleading use of errors and comments
- a fix for GICv3 on 32-bit guests
MIPS:
- fix for where the guest could wrongly map the first page of
physical memory
x86:
- nested virtualization fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
MIPS: KVM: Check for pfn noslot case
kvm: nVMX: fix nested tsc scaling
KVM: nVMX: postpone VMCS changes on MSR_IA32_APICBASE write
KVM: nVMX: fix msr bitmaps to prevent L2 from accessing L0 x2APIC
arm64: KVM: report configured SRE value to 32-bit world
arm64: KVM: remove misleading comment on pmu status
KVM: arm/arm64: timer: Workaround misconfigured timer interrupt
arm64: Document workaround for Cortex-A72 erratum #853709
KVM: arm/arm64: Change misleading use of is_error_pfn
KVM: arm64: ITS: avoid re-mapping LPIs
KVM: arm64: check for ITS device on MSI injection
KVM: arm64: ITS: move ITS registration into first VCPU run
KVM: arm64: vgic-its: Make updates to propbaser/pendbaser atomic
KVM: arm64: vgic-its: Plug race in vgic_put_irq
KVM: arm64: vgic-its: Handle errors from vgic_add_lpi
KVM: arm64: ITS: return 1 on successful MSI injection
Commit 97f2645f35 ("tree-wide: replace config_enabled() with
IS_ENABLED()") mostly killed config_enabled(), but some new users have
appeared for v4.8-rc1. They are all used for a boolean option, so can
be replaced with IS_ENABLED() safely.
Link: http://lkml.kernel.org/r/1471970749-24867-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Acked-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Storing this value will help prevent unwinders from getting out of sync
with the function graph tracer ret_stack. Now instead of needing a
stateful iterator, they can compare the return address pointer to find
the right ret_stack entry.
Note that an array of 50 ftrace_ret_stack structs is allocated for every
task. So when an arch implements this, it will add either 200 or 400
bytes of memory usage per task (depending on whether it's a 32-bit or
64-bit platform).
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Byungchul Park <byungchul.park@lge.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Nilay Vaish <nilayvaish@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/a95cfcc39e8f26b89a430c56926af0bb217bc0a1.1471607358.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When mapping a page into the guest we error check using is_error_pfn(),
however this doesn't detect a value of KVM_PFN_NOSLOT, indicating an
error HVA for the page. This can only happen on MIPS right now due to
unusual memslot management (e.g. being moved / removed / resized), or
with an Enhanced Virtual Memory (EVA) configuration where the default
KVM_HVA_ERR_* and kvm_is_error_hva() definitions are unsuitable (fixed
in a later patch). This case will be treated as a pfn of zero, mapping
the first page of physical memory into the guest.
It would appear the MIPS KVM port wasn't updated prior to being merged
(in v3.10) to take commit 81c52c56e2 ("KVM: do not treat noslot pfn as
a error pfn") into account (merged v3.8), which converted a bunch of
is_error_pfn() calls to is_error_noslot_pfn(). Switch to using
is_error_noslot_pfn() instead to catch this case properly.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.y-
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Propagate errors from kvm_mips_handle_kseg0_tlb_fault() and
kvm_mips_handle_mapped_seg_tlb_fault(), usually triggering an internal
error since they normally indicate the guest accessed bad physical
memory or the commpage in an unexpected way.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Fixes: e685c689f3 ("KVM/MIPS32: Privileged instruction/target branch emulation.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Two consecutive gfns are loaded into host TLB, so ensure the range check
isn't off by one if guest_pmap_npages is odd.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
kvm_mips_handle_mapped_seg_tlb_fault() calculates the guest frame number
based on the guest TLB EntryLo values, however it is not range checked
to ensure it lies within the guest_pmap. If the physical memory the
guest refers to is out of range then dump the guest TLB and emit an
internal error.
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
kvm_mips_handle_mapped_seg_tlb_fault() appears to map the guest page at
virtual address 0 to PFN 0 if the guest has created its own mapping
there. The intention is unclear, but it may have been an attempt to
protect the zero page from being mapped to anything but the comm page in
code paths you wouldn't expect from genuine commpage accesses (guest
kernel mode cache instructions on that address, hitting trapping
instructions when executing from that address with a coincidental TLB
eviction during the KVM handling, and guest user mode accesses to that
address).
Fix this to check for mappings exactly at KVM_GUEST_COMMPAGE_ADDR (it
may not be at address 0 since commit 42aa12e74e ("MIPS: KVM: Move
commpage so 0x0 is unmapped")), and set the corresponding EntryLo to be
interpreted as 0 (invalid).
Fixes: 858dd5d457 ("KVM/MIPS32: MMU/TLB operations for the Guest.")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # 3.10.x-
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for MIPS for 4.8. Also includes is a
minor SSB cleanup as SSB code traditionally is merged through the MIPS
tree:
ATH25:
- MIPS: Add default configuration for ath25
Boot:
- For zboot, copy appended dtb to the end of the kernel
- store the appended dtb address in a variable
BPF:
- Fix off by one error in offset allocation
Cobalt code:
- Fix typos
Core code:
- debugfs_create_file returns NULL on error, so don't use IS_ERR for
testing for errors.
- Fix double locking issue in RM7000 S-cache code. This would only
affect RM7000 ARC systems on reboot.
- Fix page table corruption on THP permission changes.
- Use compat_sys_keyctl for 32 bit userspace on 64 bit kernels.
David says, there are no compatibility issues raised by this fix.
- Move some signal code around.
- Rewrite r4k count/compare clockevent device registration such that
min_delta_ticks/max_delta_ticks files are guaranteed to be
initialized.
- Only register r4k count/compare as clockevent device if we can
assume the clock to be constant.
- Fix MSA asm warnings in control reg accessors
- uasm and tlbex fixes and tweaking.
- Print segment physical address when EU=1.
- Define AT_VECTOR_SIZE_ARCH for ARCH_DLINFO.
- CP: Allow booting by VP other than VP 0
- Cache handling fixes and optimizations for r4k class caches
- Add hotplug support for R6 processors
- Cleanup hotplug bits in kconfig
- traps: return correct si code for accessing nonmapped addresses
- Remove cpu_has_safe_index_cacheops
Lantiq:
- Register IRQ handler for virtual IRQ number
- Fix EIU interrupt loading code
- Use the real EXIN count
- Fix build error.
Loongson 3:
- Increase HPET_MIN_PROG_DELTA and decrease HPET_MIN_CYCLES
Octeon:
- Delete built-in DTB pruning code for D-Link DSR-1000N.
- Clean up GPIO definitions in dlink_dsr-1000n.dts.
- Add more LEDs to the DSR-100n DTS
- Fix off by one in octeon_irq_gpio_map()
- Typo fixes
- Enable SATA by default in cavium_octeon_defconfig
- Support readq/writeq()
- Remove forced mappings of USB interrupts.
- Ensure DMA descriptors are always in the low 4GB
- Improve USB reset code for OCTEON II.
Pistachio:
- Add maintainers entry for pistachio SoC Support
- Remove plat_setup_iocoherency
Ralink:
- Fix pwm UART in spis group pinmux.
SSB:
- Change bare unsigned to unsigned int to suit coding style
Tools:
- Fix reloc tool compiler warnings.
Other:
- Delete use of ARCH_WANT_OPTIONAL_GPIOLIB"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (61 commits)
MIPS: mm: Fix definition of R6 cache instruction
MIPS: tools: Fix relocs tool compiler warnings
MIPS: Cobalt: Fix typo
MIPS: Octeon: Fix typo
MIPS: Lantiq: Fix build failure
MIPS: Use CPHYSADDR to implement mips32 __pa
MIPS: Octeon: Dlink_dsr-1000n.dts: add more leds.
MIPS: Octeon: Clean up GPIO definitions in dlink_dsr-1000n.dts.
MIPS: Octeon: Delete built-in DTB pruning code for D-Link DSR-1000N.
MIPS: store the appended dtb address in a variable
MIPS: ZBOOT: copy appended dtb to the end of the kernel
MIPS: ralink: fix spis group pinmux
MIPS: Factor o32 specific code into signal_o32.c
MIPS: non-exec stack & heap when non-exec PT_GNU_STACK is present
MIPS: Use per-mm page to execute branch delay slot instructions
MIPS: Modify error handling
MIPS: c-r4k: Use SMP calls for CM indexed cache ops
MIPS: c-r4k: Avoid small flush_icache_range SMP calls
MIPS: c-r4k: Local flush_icache_range cache op override
MIPS: c-r4k: Split r4k_flush_kernel_vmap_range()
...
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup rtc-cmos,
rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after shutdown for QNAP
TS-41x
- s3c: clock fixes
-----BEGIN PGP SIGNATURE-----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=rpGB
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
The dma-mapping core and the implementations do not change the DMA
attributes passed by pointer. Thus the pointer can point to const data.
However the attributes do not have to be a bitfield. Instead unsigned
long will do fine:
1. This is just simpler. Both in terms of reading the code and setting
attributes. Instead of initializing local attributes on the stack
and passing pointer to it to dma_set_attr(), just set the bits.
2. It brings safeness and checking for const correctness because the
attributes are passed by value.
Semantic patches for this change (at least most of them):
virtual patch
virtual context
@r@
identifier f, attrs;
@@
f(...,
- struct dma_attrs *attrs
+ unsigned long attrs
, ...)
{
...
}
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
and
// Options: --all-includes
virtual patch
virtual context
@r@
identifier f, attrs;
type t;
@@
t f(..., struct dma_attrs *attrs);
@@
identifier r.f;
@@
f(...,
- NULL
+ 0
)
Link: http://lkml.kernel.org/r/1468399300-5399-2-git-send-email-k.kozlowski@samsung.com
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no>
Acked-by: Mark Salter <msalter@redhat.com> [c6x]
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com> [cris]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> [drm]
Reviewed-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Fabien Dessenne <fabien.dessenne@st.com> [bdisp]
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> [vb2-core]
Acked-by: David Vrabel <david.vrabel@citrix.com> [xen]
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [xen swiotlb]
Acked-by: Joerg Roedel <jroedel@suse.de> [iommu]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Gerald Schaefer <gerald.schaefer@de.ibm.com> [s390]
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Hans-Christian Noren Egtvedt <egtvedt@samfundet.no> [avr32]
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arc]
Acked-by: Robin Murphy <robin.murphy@arm.com> [arm64 and dma-iommu]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The use of config_enabled() against config options is ambiguous. In
practical terms, config_enabled() is equivalent to IS_BUILTIN(), but the
author might have used it for the meaning of IS_ENABLED(). Using
IS_ENABLED(), IS_BUILTIN(), IS_MODULE() etc. makes the intention
clearer.
This commit replaces config_enabled() with IS_ENABLED() where possible.
This commit is only touching bool config options.
I noticed two cases where config_enabled() is used against a tristate
option:
- config_enabled(CONFIG_HWMON)
[ drivers/net/wireless/ath/ath10k/thermal.c ]
- config_enabled(CONFIG_BACKLIGHT_CLASS_DEVICE)
[ drivers/gpu/drm/gma500/opregion.c ]
I did not touch them because they should be converted to IS_BUILTIN()
in order to keep the logic, but I was not sure it was the authors'
intention.
Link: http://lkml.kernel.org/r/1465215656-20569-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: Stas Sergeev <stsp@list.ru>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: "Dmitry V. Levin" <ldv@altlinux.org>
Cc: yu-cheng yu <yu-cheng.yu@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Will Drewry <wad@chromium.org>
Cc: Nikolay Martynov <mar.kolya@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Rafal Milecki <zajec5@gmail.com>
Cc: James Cowgill <James.Cowgill@imgtec.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Alex Smith <alex.smith@imgtec.com>
Cc: Adam Buchbinder <adam.buchbinder@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Hidehiro Kawai <hidehiro.kawai.ez@hitachi.com>
Cc: "Luis R. Rodriguez" <mcgrof@do-not-panic.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Roland McGrath <roland@hack.frob.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tony Wu <tung7970@gmail.com>
Cc: Huaitong Han <huaitong.han@intel.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Andrea Gelmini <andrea.gelmini@gelma.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: "Maciej W. Rozycki" <macro@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When using clang as HOSTCC, the following warnings appear:
In file included from arch/mips/boot/tools/relocs_64.c:27:0:
arch/mips/boot/tools/relocs.c: In function ‘read_relocs’:
arch/mips/boot/tools/relocs.c:397:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
ELF_R_SYM(rel->r_info) = elf32_to_cpu(ELF_R_SYM(rel->r_info));
^~~~~~~~~
arch/mips/boot/tools/relocs.c:397:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
arch/mips/boot/tools/relocs.c: In function ‘walk_relocs’:
arch/mips/boot/tools/relocs.c:491:4: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Elf_Sym *sym = &sh_symtab[ELF_R_SYM(rel->r_info)];
^~~~~~~
arch/mips/boot/tools/relocs.c: In function ‘do_reloc’:
arch/mips/boot/tools/relocs.c:502:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
unsigned r_type = ELF_R_TYPE(rel->r_info);
^~~~~~~~
arch/mips/boot/tools/relocs.c: In function ‘do_reloc_info’:
arch/mips/boot/tools/relocs.c:641:3: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
rel_type(ELF_R_TYPE(rel->r_info)),
^~~~~~~~
Fix them by making Elf64_Mips_Rela a union
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Acked-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13683/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some configs of mips like xway_defconffig are failing with the error:
arch/mips/lantiq/irq.c:209:2: error: initialization from incompatible
pointer type [-Werror]
"icu",
^
arch/mips/lantiq/irq.c:209:2: error: (near initialization for
'ltq_irq_type.parent_device') [-Werror]
arch/mips/lantiq/irq.c:219:2: error: initialization from incompatible
pointer type [-Werror]
"eiu",
^
arch/mips/lantiq/irq.c:219:2: error: (near initialization for
'ltq_eiu_type.parent_device') [-Werror]
The first member of the "struct irq" is no longer a pointer for the
name.
Fixes: be45beb2df ("genirq: Add runtime power management support for IRQ chips")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: John Crispin <john@phrozen.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13684/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge yet more updates from Andrew Morton:
- the rest of ocfs2
- various hotfixes, mainly MM
- quite a bit of misc stuff - drivers, fork, exec, signals, etc.
- printk updates
- firmware
- checkpatch
- nilfs2
- more kexec stuff than usual
- rapidio updates
- w1 things
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (111 commits)
ipc: delete "nr_ipc_ns"
kcov: allow more fine-grained coverage instrumentation
init/Kconfig: add clarification for out-of-tree modules
config: add android config fragments
init/Kconfig: ban CONFIG_LOCALVERSION_AUTO with allmodconfig
relay: add global mode support for buffer-only channels
init: allow blacklisting of module_init functions
w1:omap_hdq: fix regression
w1: add helper macro module_w1_family
w1: remove need for ida and use PLATFORM_DEVID_AUTO
rapidio/switches: add driver for IDT gen3 switches
powerpc/fsl_rio: apply changes for RIO spec rev 3
rapidio: modify for rev.3 specification changes
rapidio: change inbound window size type to u64
rapidio/idt_gen2: fix locking warning
rapidio: fix error handling in mbox request/release functions
rapidio/tsi721_dma: advance queue processing from transfer submit call
rapidio/tsi721: add messaging mbox selector parameter
rapidio/tsi721: add PCIe MRRS override parameter
rapidio/tsi721_dma: add channel mask and queue size parameters
...
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
VGIC implementation.
- s390: support for trapping software breakpoints, nested virtualization
(vSIE), the STHYI opcode, initial extensions for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots of cleanups,
preliminary to this and the upcoming support for hardware virtualization
extensions.
- x86: support for execute-only mappings in nested EPT; reduced vmexit
latency for TSC deadline timer (by about 30%) on Intel hosts; support for
more than 255 vCPUs.
- PPC: bugfixes.
The ugly bit is the conflicts. A couple of them are simple conflicts due
to 4.7 fixes, but most of them are with other trees. There was definitely
too much reliance on Acked-by here. Some conflicts are for KVM patches
where _I_ gave my Acked-by, but the worst are for this pull request's
patches that touch files outside arch/*/kvm. KVM submaintainers should
probably learn to synchronize better with arch maintainers, with the
latter providing topic branches whenever possible instead of Acked-by.
This is what we do with arch/x86. And I should learn to refuse pull
requests when linux-next sends scary signals, even if that means that
submaintainers have to rebase their branches.
Anyhow, here's the list:
- arch/x86/kvm/vmx.c: handle_pcommit and EXIT_REASON_PCOMMIT was removed
by the nvdimm tree. This tree adds handle_preemption_timer and
EXIT_REASON_PREEMPTION_TIMER at the same place. In general all mentions
of pcommit have to go.
There is also a conflict between a stable fix and this patch, where the
stable fix removed the vmx_create_pml_buffer function and its call.
- virt/kvm/kvm_main.c: kvm_cpu_notifier was removed by the hotplug tree.
This tree adds kvm_io_bus_get_dev at the same place.
- virt/kvm/arm/vgic.c: a few final bugfixes went into 4.7 before the
file was completely removed for 4.8.
- include/linux/irqchip/arm-gic-v3.h: this one is entirely our fault;
this is a change that should have gone in through the irqchip tree and
pulled by kvm-arm. I think I would have rejected this kvm-arm pull
request. The KVM version is the right one, except that it lacks
GITS_BASER_PAGES_SHIFT.
- arch/powerpc: what a mess. For the idle_book3s.S conflict, the KVM
tree is the right one; everything else is trivial. In this case I am
not quite sure what went wrong. The commit that is causing the mess
(fd7bacbca4, "KVM: PPC: Book3S HV: Fix TB corruption in guest exit
path on HMI interrupt", 2016-05-15) touches both arch/powerpc/kernel/
and arch/powerpc/kvm/. It's large, but at 396 insertions/5 deletions
I guessed that it wasn't really possible to split it and that the 5
deletions wouldn't conflict. That wasn't the case.
- arch/s390: also messy. First is hypfs_diag.c where the KVM tree
moved some code and the s390 tree patched it. You have to reapply the
relevant part of commits 6c22c98637, plus all of e030c1125e, to
arch/s390/kernel/diag.c. Or pick the linux-next conflict
resolution from http://marc.info/?l=kvm&m=146717549531603&w=2.
Second, there is a conflict in gmap.c between a stable fix and 4.8.
The KVM version here is the correct one.
I have pushed my resolution at refs/heads/merge-20160802 (commit
3d1f53419842) at git://git.kernel.org/pub/scm/virt/kvm/kvm.git.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJXoGm7AAoJEL/70l94x66DugQIAIj703ePAFepB/fCrKHkZZia
SGrsBdvAtNsOhr7FQ5qvvjLxiv/cv7CymeuJivX8H+4kuUHUllDzey+RPHYHD9X7
U6n1PdCH9F15a3IXc8tDjlDdOMNIKJixYuq1UyNZMU6NFwl00+TZf9JF8A2US65b
x/41W98ilL6nNBAsoDVmCLtPNWAqQ3lajaZELGfcqRQ9ZGKcAYOaLFXHv2YHf2XC
qIDMf+slBGSQ66UoATnYV2gAopNlWbZ7n0vO6tE2KyvhHZ1m399aBX1+k8la/0JI
69r+Tz7ZHUSFtmlmyByi5IAB87myy2WQHyAPwj+4vwJkDGPcl0TrupzbG7+T05Y=
=42ti
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
- ARM: GICv3 ITS emulation and various fixes. Removal of the
old VGIC implementation.
- s390: support for trapping software breakpoints, nested
virtualization (vSIE), the STHYI opcode, initial extensions
for CPU model support.
- MIPS: support for MIPS64 hosts (32-bit guests only) and lots
of cleanups, preliminary to this and the upcoming support for
hardware virtualization extensions.
- x86: support for execute-only mappings in nested EPT; reduced
vmexit latency for TSC deadline timer (by about 30%) on Intel
hosts; support for more than 255 vCPUs.
- PPC: bugfixes.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (302 commits)
KVM: PPC: Introduce KVM_CAP_PPC_HTM
MIPS: Select HAVE_KVM for MIPS64_R{2,6}
MIPS: KVM: Reset CP0_PageMask during host TLB flush
MIPS: KVM: Fix ptr->int cast via KVM_GUEST_KSEGX()
MIPS: KVM: Sign extend MFC0/RDHWR results
MIPS: KVM: Fix 64-bit big endian dynamic translation
MIPS: KVM: Fail if ebase doesn't fit in CP0_EBase
MIPS: KVM: Use 64-bit CP0_EBase when appropriate
MIPS: KVM: Set CP0_Status.KX on MIPS64
MIPS: KVM: Make entry code MIPS64 friendly
MIPS: KVM: Use kmap instead of CKSEG0ADDR()
MIPS: KVM: Use virt_to_phys() to get commpage PFN
MIPS: Fix definition of KSEGX() for 64-bit
KVM: VMX: Add VMCS to CPU's loaded VMCSs before VMPTRLD
kvm: x86: nVMX: maintain internal copy of current VMCS
KVM: PPC: Book3S HV: Save/restore TM state in H_CEDE
KVM: PPC: Book3S HV: Pull out TM state save/restore into separate procedures
KVM: arm64: vgic-its: Simplify MAPI error handling
KVM: arm64: vgic-its: Make vgic_its_cmd_handle_mapi similar to other handlers
KVM: arm64: vgic-its: Turn device_id validation into generic ID validation
...
Use CPHYSADDR to implement the __pa macro converting from a virtual to a
physical address for MIPS32, much as is already done for MIPS64 (though
without the complication of having both compatibility & XKPHYS
segments).
This allows for __pa to work regardless of whether the address being
translated is in kseg0 or kseg1, unlike the previous subtraction based
approach which only worked for addresses in kseg0. Working for kseg1
addresses is important if __pa is used on addresses allocated by
dma_alloc_coherent, where on systems with non-coherent I/O we provide
addresses in kseg1. If this address is then used with
dma_map_single_attrs then it is provided to virt_to_page, which in turn
calls virt_to_phys which is a wrapper around __pa. The result is that we
end up with a physical address 0x20000000 bytes (ie. the size of kseg0)
too high.
In addition to providing consistency with MIPS64 & fixing the kseg1 case
above this has the added bonus of generating smaller code for systems
implementing MIPS32r2 & beyond, where a single ext instruction can
extract the physical address rather than needing to load an immediate
into a temp register & subtract it. This results in ~1.3KB savings for a
boston_defconfig kernel adjusted to set CONFIG_32BIT=y.
This patch does not change the EVA case, which may or may not have
similar issues around handling both cached & uncached addresses but is
beyond the scope of this patch.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13836/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of rewriting the arguments to match the UHI spec, store the
address of a appended or UHI supplied dtb in fw_supplied_dtb.
That way the original bootloader arugments are kept intact while still
making the use of an appended dtb invisible for mach code.
Mach code can still find out if it is an appended dtb by comparing
fw_arg1 with fw_supplied_dtb.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13699/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of rewriting the arguments, just move the appended dtb to where
the decompressed kernel expects it. This eliminates the need for special
casing vmlinuz.bin appended dtb files.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: John Crispin <john@phrozen.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Alban Bedel <albeu@free.fr>
Cc: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13698/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The commit ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
caused building a 64 bit kernel with support for n32 and not o32
to produce a build error:
arch/mips/kernel/signal32.c:415:11: error: ‘vdso_image_o32’ undeclared here (not in a function)
.vdso = &vdso_image_o32,
Fix this by moving the o32 specific code into signal_o32.c and
updating the Makefile accordingly.
Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Alex Smith <alex@alex-smith.me.uk>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13690/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The stack and heap have both been executable by default on MIPS until
now. This patch changes the default to be non-executable, but only for
ELF binaries with a non-executable PT_GNU_STACK header present. This
does apply to both the heap & the stack, despite the name PT_GNU_STACK,
and this matches the behaviour of other architectures like ARM & x86.
Current MIPS toolchains do not produce the PT_GNU_STACK header, which
means that we can rely upon this patch not changing the behaviour of
existing binaries. The new default will only take effect for newly
compiled binaries once toolchains are updated to support PT_GNU_STACK,
and since those binaries are newly compiled they can be compiled
expecting the change in default behaviour. Again this matches the way in
which the ARM & x86 architectures handled their implementations of
non-executable memory.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Maciej Rozycki <maciej.rozycki@imgtec.com>
Cc: Faraz Shahbazker <faraz.shahbazker@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13765/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In some cases the kernel needs to execute an instruction from the delay
slot of an emulated branch instruction. These cases include:
- Emulated floating point branch instructions (bc1[ft]l?) for systems
which don't include an FPU, or upon which the kernel is run with the
"nofpu" parameter.
- MIPSr6 systems running binaries targeting older revisions of the
architecture, which may include branch instructions whose encodings
are no longer valid in MIPSr6.
Executing instructions from such delay slots is done by writing the
instruction to memory followed by a trap, as part of an "emuframe", and
executing it. This avoids the requirement of an emulator for the entire
MIPS instruction set. Prior to this patch such emuframes are written to
the user stack and executed from there.
This patch moves FP branch delay emuframes off of the user stack and
into a per-mm page. Allocating a page per-mm leaves userland with access
to only what it had access to previously, and compared to other
solutions is relatively simple.
When a thread requires a delay slot emulation, it is allocated a frame.
A thread may only have one frame allocated at any one time, since it may
only ever be executing one instruction at any one time. In order to
ensure that we can free up allocated frame later, its index is recorded
in struct thread_struct. In the typical case, after executing the delay
slot instruction we'll execute a break instruction with the BRK_MEMU
code. This traps back to the kernel & leads to a call to do_dsemulret
which frees the allocated frame & moves the user PC back to the
instruction that would have executed following the emulated branch.
In some cases the delay slot instruction may be invalid, such as a
branch, or may trigger an exception. In these cases the BRK_MEMU break
instruction will not be hit. In order to ensure that frames are freed
this patch introduces dsemul_thread_cleanup() and calls it to free any
allocated frame upon thread exit. If the instruction generated an
exception & leads to a signal being delivered to the thread, or indeed
if a signal simply happens to be delivered to the thread whilst it is
executing from the struct emuframe, then we need to take care to exit
the frame appropriately. This is done by either rolling back the user PC
to the branch or advancing it to the continuation PC prior to signal
delivery, using dsemul_thread_rollback(). If this were not done then a
sigreturn would return to the struct emuframe, and if that frame had
meanwhile been used in response to an emulated branch instruction within
the signal handler then we would execute the wrong user code.
Whilst a user could theoretically place something like a compact branch
to self in a delay slot and cause their thread to become stuck in an
infinite loop with the frame never being deallocated, this would:
- Only affect the users single process.
- Be architecturally invalid since there would be a branch in the
delay slot, which is forbidden.
- Be extremely unlikely to happen by mistake, and provide a program
with no more ability to harm the system than a simple infinite loop
would.
If a thread requires a delay slot emulation & no frame is available to
it (ie. the process has enough other threads that all frames are
currently in use) then the thread joins a waitqueue. It will sleep until
a frame is freed by another thread in the process.
Since we now know whether a thread has an allocated frame due to our
tracking of its index, the cookie field of struct emuframe is removed as
we can be more certain whether we have a valid frame. Since a thread may
only ever have a single frame at any given time, the epc field of struct
emuframe is also removed & the PC to continue from is instead stored in
struct thread_struct. Together these changes simplify & shrink struct
emuframe somewhat, allowing twice as many frames to fit into the page
allocated for them.
The primary benefit of this patch is that we are now free to mark the
user stack non-executable where that is possible.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Maciej Rozycki <maciej.rozycki@imgtec.com>
Cc: Faraz Shahbazker <faraz.shahbazker@imgtec.com>
Cc: Raghu Gandham <raghu.gandham@imgtec.com>
Cc: Matthew Fortune <matthew.fortune@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13764/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
debugfs_create_file returns NULL on error so an IS_ERR test is
incorrect here and a NULL check is required.
The Coccinelle semantic patch used to make this change is as follows:
@@
expression e;
@@
e = debugfs_create_file(...);
if(
- IS_ERR(e)
+ !e
)
{
<+...
return
- PTR_ERR(e)
+ -ENOMEM
;
...+>
}
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Cc: julia.lawall@lip6.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/13834/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are now able to support KVM T&E with MIPS32 guests on some MIPS64r2
and MIPS64r6 hosts, so select HAVE_KVM so it can be enabled.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM sometimes flushes host TLB entries, reading each one to check if it
corresponds to a guest KSeg0 address. In the absence of EntryHi.EHInv
bits to invalidate the whole entry, the entries will be set to unique
virtual addresses in KSeg0 (which is not TLB mapped), spaced 2*PAGE_SIZE
apart.
The TLB read however will clobber the CP0_PageMask register with
whatever page size that TLB entry had, and that same page size will be
written back into the TLB entry along with the unique address.
This would cause breakage when transparent huge pages are enabled on
64-bit host kernels, since huge page entries will overlap other nearby
entries when separated by only 2*PAGE_SIZE, causing a machine check
exception.
Fix this by restoring the old CP0_PageMask value (which should be set to
the normal page size) after reading the TLB entry if we're going to go
ahead and invalidate it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_mips_trans_replace() passes a pointer to KVM_GUEST_KSEGX(). This
breaks on 64-bit builds due to the cast of that 64-bit pointer to a
different sized 32-bit int. Cast the pointer argument to an unsigned
long to work around the warning.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When emulating MFC0 instructions to load 32-bit values from guest COP0
registers and the RDHWR instruction to read the CC (Count) register,
sign extend the result to comply with the MIPS64 architecture. The
result must be in canonical 32-bit form or the guest may malfunction.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MFC0 and MTC0 instructions in the guest which cause traps can be
replaced with 32-bit loads and stores to the commpage, however on big
endian 64-bit builds the offset needs to have 4 added so as to
load/store the least significant half of the long instead of the most
significant half.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Fail if the address of the allocated exception base doesn't fit into the
CP0_EBase register. This can happen on MIPS64 if CP0_EBase.WG isn't
implemented but RAM is available outside of the range of KSeg0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the KVM entry point to write CP0_EBase as a 64-bit register when
it is 64-bits wide, and to set the WG (write gate) bit if it exists in
order to write bits 63:30 (or 31:30 on MIPS32).
Prior to MIPS64r6 it was UNDEFINED to perform a 64-bit read or write of
a 32-bit COP0 register. Since this is dynamically generated code,
generate the right type of access depending on whether the kernel is
64-bit and cpu_has_ebase_wg.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Update the KVM entry code to set the CP0_Entry.KX bit on 64-bit kernels.
This is important to allow the entry code, running in kernel mode, to
access the full 64-bit address space right up to the point of entering
the guest, and immediately after exiting the guest, so it can safely
restore & save the guest context from 64-bit segments.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The MIPS KVM entry code (originally kvm_locore.S, later locore.S, and
now entry.c) has never quite been right when built for 64-bit, using
32-bit instructions when 64-bit instructions were needed for handling
64-bit registers and pointers. Fix several cases of this now.
The changes roughly fall into the following categories.
- COP0 scratch registers contain guest register values and the VCPU
pointer, and are themselves full width. Similarly CP0_EPC and
CP0_BadVAddr registers are full width (even though technically we
don't support 64-bit guest address spaces with trap & emulate KVM).
Use MFC0/MTC0 for accessing them.
- Handling of stack pointers and the VCPU pointer must match the pointer
size of the kernel ABI (always o32 or n64), so use ADDIU.
- The CPU number in thread_info, and the guest_{user,kernel}_asid arrays
in kvm_vcpu_arch are all 32 bit integers, so use lw (instead of LW) to
load them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There are several unportable uses of CKSEG0ADDR() in MIPS KVM, which
implicitly assume that a host physical address will be in the low 512MB
of the physical address space (accessible in KSeg0). These assumptions
don't hold for highmem or on 64-bit kernels.
When interpreting the guest physical address when reading or overwriting
a trapping instruction, use kmap_atomic() to get a usable virtual
address to access guest memory, which is portable to 64-bit and highmem
kernels.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Calculate the PFN of the commpage using virt_to_phys() instead of
CPHYSADDR(). This is more portable as kzalloc() may allocate from XKPhys
instead of KSeg0 on 64-bit kernels, which CPHYSADDR() doesn't handle.
This is sufficient for highmem kernels too since kzalloc() will allocate
from lowmem in KSeg0.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Radim Krčmář" <rkrcmar@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KSEGX() macro is defined to 32-bit sign extend the address argument
and logically AND the result with 0xe0000000, with the final result
usually compared against one of the CKSEG macros. However the literal
0xe0000000 is unsigned as the high bit is set, and is therefore
zero-extended on 64-bit kernels, resulting in the sign extension bits of
the argument being masked to zero. This results in the odd situation
where:
KSEGX(CKSEG) != CKSEG
(0xffffffff80000000 & 0x00000000e0000000) != 0xffffffff80000000)
Fix this by 32-bit sign extending the 0xe0000000 literal using
_ACAST32_.
This will help some MIPS KVM code handling 32-bit guest addresses to
work on 64-bit host kernels, but will also affect KSEGX in
dec_kn01_be_backend() on a 64-bit DECstation kernel, and the SiByte DMA
page ops KSEGX check in clear_page() and copy_page() on 64-bit SB1
kernels, neither of which appear to be designed with 64-bit segments in
mind anyway.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
Pull security subsystem updates from James Morris:
"Highlights:
- TPM core and driver updates/fixes
- IPv6 security labeling (CALIPSO)
- Lots of Apparmor fixes
- Seccomp: remove 2-phase API, close hole where ptrace can change
syscall #"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (156 commits)
apparmor: fix SECURITY_APPARMOR_HASH_DEFAULT parameter handling
tpm: Add TPM 2.0 support to the Nuvoton i2c driver (NPCT6xx family)
tpm: Factor out common startup code
tpm: use devm_add_action_or_reset
tpm2_i2c_nuvoton: add irq validity check
tpm: read burstcount from TPM_STS in one 32-bit transaction
tpm: fix byte-order for the value read by tpm2_get_tpm_pt
tpm_tis_core: convert max timeouts from msec to jiffies
apparmor: fix arg_size computation for when setprocattr is null terminated
apparmor: fix oops, validate buffer size in apparmor_setprocattr()
apparmor: do not expose kernel stack
apparmor: fix module parameters can be changed after policy is locked
apparmor: fix oops in profile_unpack() when policy_db is not present
apparmor: don't check for vmalloc_addr if kvzalloc() failed
apparmor: add missing id bounds check on dfa verification
apparmor: allow SYS_CAP_RESOURCE to be sufficient to prlimit another task
apparmor: use list_next_entry instead of list_entry_next
apparmor: fix refcount race when finding a child profile
apparmor: fix ref count leak when profile sha1 hash is read
apparmor: check that xindex is in trans_table bounds
...
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
The MIPS Coherence Manager (CM) can propagate address-based ("hit")
cache operations to other cores in the coherent system, alleviating
software of the need to use SMP calls, however indexed cache operations
are not propagated by hardware since doing so makes no sense for
separate caches.
Update r4k_op_needs_ipi() to report that only hit cache operations are
globalized by the CM, requiring indexed cache operations to be
globalized by software via an SMP call.
r4k_on_each_cpu() previously had a special case for CONFIG_MIPS_MT_SMP,
intended to avoid the SMP calls when the only other CPUs in the system
were other VPEs in the same core, and hence sharing the same caches.
This was changed by commit cccf34e941 ("MIPS: c-r4k: Fix cache
flushing for MT cores") to apparently handle multi-core multi-VPE
systems, but it focussed mainly on hit cache ops, so the SMP calls were
still disabled entirely for CM systems.
This doesn't normally cause problems, but tests can be written to hit
these corner cases by using multiple threads, or changing task
affinities to force the process to migrate cores. For example the
failure of mprotect RW->RX to globally sync icaches (via
flush_cache_range) can be detected by modifying and mprotecting a code
page on one core, and migrating to a different core to execute from it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13807/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Avoid SMP calls for flushing small icache ranges. On non-CM platforms,
and CM platforms too after we make r4k_on_each_cpu() take the cache op
type into account, it will be called on multiple CPUs due to the
possibility that local_r4k_flush_icache_range_ipi() could do
non-globalized indexed cache ops. This rougly copies the range size
check out into r4k_flush_icache_range(), which can disallow indexed
cache ops and allow r4k_on_each_cpu() to skip the SMP call.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13805/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Allow the permitted cache op types used by
local_r4k_flush_icache_range_ipi() to be overridden by the SMP caller.
This will allow SMP calls to be avoided under certain circumstances,
falling back to a single CPU performing globalized hit cache ops only.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13803/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split the operation of r4k_flush_kernel_vmap_range() into separate
SMP callbacks for the indexed cache flush and hit cache flush cases,
since the logic to determine which to use can be determined by the
initiating CPU prior to doing any SMP calls.
This will help when we change r4k_on_each_cpu() to distinguish indexed
and hit cache ops in a later patch, preventing globalized hit cache ops
being performed redundantly on multiple CPUs.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13806/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When performing SMP calls to foreign cores, exclude sibling CPUs from
the provided map, as we already handle the local core on the current
CPU. This prevents an SMP call from for example core 0, VPE 1 to VPE 0
on the same core.
In the process the cpu_foreign_map cpumask is turned into an array of
cpumasks, so that each CPU has its own version of it which excludes
sibling CPUs. r4k_op_needs_ipi() is also updated to reflect that cache
management SMP calls are not needed when all CPUs are siblings (i.e.
there are no foreign CPUs according to the new cpu_foreign_map[]
semantics which exclude siblings).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Jayachandran C. <jchandra@broadcom.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several cache operations are optimised to return early from the SMP call
handler if the memory map in question has no valid ASID on the current
CPU, or any online CPU in the case of MIPS_MT_SMP. The idea is that if a
memory map has never been used on a CPU it shouldn't have cache lines in
need of flushing.
However this doesn't cover all cases when ASIDs for other CPUs need to
be checked:
- Offline VPEs may have recently been online and brought lines into the
(shared) cache, so they should also be checked, rather than only
online CPUs.
- SMP systems with a Coherence Manager (CM), but with MT disabled still
have globalized hit cache ops, but don't use SMP calls, so all present
CPUs should be taken into account.
- R6 systems have a different multithreading implementation, so
MIPS_MT_SMP won't be set, but as above may still have a CM which
globalizes hit cache ops.
Additionally for non-globalized cache operations where an SMP call to a
single VPE in each foreign core is used, it is not necessary to check
every CPU in the system, only sibling CPUs sharing the same first level
cache.
Fix this by making has_valid_asid() take a cache op type argument like
r4k_on_each_cpu(), so it can determine whether r4k_on_each_cpu() will
have done SMP calls to other cores. It can then determine which set of
CPUs to check the ASIDs of based on that, excluding foreign CPUs if an
SMP call will have been performed.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The r4k_on_each_cpu() function calls the specified cache flush helper on
other CPUs if deemed necessary due to the cache ops not being
globalized by hardware. However this really depends on the cache op
addressing type, as the MIPS Coherence Manager (CM) if present will
globalize "hit" cache ops (addressed by virtual address), but not
"index" cache ops (addressed by cache index). This results in index
cache ops only being performed on a single CPU when CM is present.
Most (but not all) of the functions called by r4k_on_each_cpu() perform
cache operations exclusively with a single cache op type, so add a type
argument and modify the callers to pass in some combination of R4K_HIT
(global kernel virtual addressing or user virtual addressing
conditional upon matching active_mm) and R4K_INDEX (index into cache).
This will allow r4k_on_each_cpu() to later distinguish these cases and
decide whether to perform an SMP call based on it.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13798/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Avoid the dcache and scache flush in local_r4k_flush_cache_sigtramp() if
the icache fills straight from the dcache.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13802/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix r4k_flush_cache_sigtramp() and local_r4k_flush_cache_sigtramp() to
flush the delay slot emulation trampoline cacheline through a kmap
rather than directly when the active_mm doesn't match that of the task
initiating the flush, a bit like local_r4k_flush_cache_page() does.
This would fix a corner case on SMP systems without hardware globalized
hit cache ops, where a migration to another CPU after the flush, where
that CPU did not have the same mm active at the time of the flush, could
result in stale icache content being executed instead of the trampoline,
e.g. from a previous delay slot emulation with a similar stack pointer.
This case was artificially triggered by replacing the icache flush with
a full indexed flush (not globalized on CM systems) and forcing the SMP
call to take place, with a test program that alternated two FPU delay
slots with a parent process repeatedly changing scheduler affinity.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13797/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The protected_writeback_scache_line() function is used by
local_r4k_flush_cache_sigtramp() to flush an FPU delay slot emulation
trampoline on the userland stack from the caches so it is visible to
subsequent instruction fetches.
Commit de8974e3f7 ("MIPS: asm: r4kcache: Add EVA cache flushing
functions") updated some protected_ cache flush functions to use EVA
CACHEE instructions via protected_cachee_op(), and commit 83fd43449b
("MIPS: r4kcache: Add EVA case for protected_writeback_dcache_line") did
the same thing for protected_writeback_dcache_line(), but
protected_writeback_scache_line() never got updated. Lets fix that now
to flush the right user address from the secondary cache rather than
some arbitrary kernel unmapped address.
This issue was spotted through code inspection, and it seems unlikely to
be possible to hit this in practice. It theoretically affect EVA kernels
on EVA capable cores with an L2 cache, where the icache fetches straight
from RAM (cpu_icache_snoops_remote_store == 0), running a hard float
userland with FPU disabled (nofpu). That both Malta and Boston platforms
override cpu_icache_snoops_remote_store to 1 suggests that all MIPS
cores fetch instructions into icache straight from L2 rather than RAM.
Fixes: de8974e3f7 ("MIPS: asm: r4kcache: Add EVA cache flushing functions")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13800/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit cccf34e941 ("MIPS: c-r4k: Fix cache flushing for MT cores")
added the cpu_foreign_map cpumask containing a single VPE from each
online core, and recalculated it when secondary CPUs are brought up.
stop_this_cpu() was also updated to recalculate cpu_foreign_map, but
with an additional hack before marking the CPU as offline to copy
cpu_online_mask into cpu_foreign_map and perform an SMP memory barrier.
This appears to have been intended to prevent cache management IPIs
being missed when the VPE representing the core in cpu_foreign_map is
taken offline while other VPEs remain online. Unfortunately there is
nothing in this hack to prevent r4k_on_each_cpu() from reading the old
cpu_foreign_map, and smp_call_function_many() from reading that new
cpu_online_mask with the core's representative VPE marked offline. It
then wouldn't send an IPI to any online VPEs of that core.
stop_this_cpu() is only actually called in panic and system shutdown /
halt / reboot situations, in which case all CPUs are going down and we
don't really need to care about cache management, so drop this hack.
Note that the __cpu_disable() case for CPU hotplug is handled in the
previous commit, and no synchronisation is needed there due to the use
of stop_machine() which prevents hotplug from taking place while any CPU
has disabled preemption (as r4k_on_each_cpu() does).
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13796/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When a CPU is disabled via CPU hotplug, cpu_foreign_map is not updated.
This could result in cache management SMP calls being sent to offline
CPUs instead of online siblings in the same core.
Add a call to calculate_cpu_foreign_map() in the various MIPS cpu
disable callbacks after set_cpu_online(). All cases are updated for
consistency and to keep cpu_foreign_map strictly up to date, not just
those which may support hardware multithreading.
Fixes: cccf34e941 ("MIPS: c-r4k: Fix cache flushing for MT cores")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Hongliang Tao <taohl@lemote.com>
Cc: Hua Yan <yanh@lemote.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13799/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SMP flush_tlb_*() functions may clear the memory map's ASIDs for
other CPUs if the mm has only a single user (the current CPU) in order
to avoid SMP calls. However this makes it appear to has_valid_asid(),
which is used by various cache flush functions, as if the CPUs have
never run in the mm, and therefore can't have cached any of its memory.
For flush_tlb_mm() this doesn't sound unreasonable.
flush_tlb_range() corresponds to flush_cache_range() which does do full
indexed cache flushes, but only on the icache if the specified mapping
is executable, otherwise it doesn't guarantee that there are no cache
contents left for the mm.
flush_tlb_page() corresponds to flush_cache_page(), which will perform
address based cache ops on the specified page only, and also only
touches the icache if the page is executable. It does not guarantee that
there are no cache contents left for the mm.
For example, this affects flush_cache_range() which uses the
has_valid_asid() optimisation. It is required to flush the icache when
mappings are made executable (e.g. using mprotect) so they are
immediately usable. If some code is changed to non executable in order
to be modified then it will not be flushed from the icache during that
time, but the ASID on other CPUs may still be cleared for TLB flushing.
When the code is changed back to executable, flush_cache_range() will
assume the code hasn't run on those other CPUs due to the zero ASID, and
won't invalidate the icache on them.
This is fixed by clearing the other CPUs ASIDs to 1 instead of 0 for the
above two flush_tlb_*() functions when the corresponding cache flushes
are likely to be incomplete (non executable range flush, or any page
flush). This ASID appears valid to has_valid_asid(), but still triggers
ASID regeneration due to the upper ASID version bits being 0, which is
less than the minimum ASID version of 1 and so always treated as stale.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Leonid Yegoshin <leonid.yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/13795/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
