We get the insertion event before the jack is fully inserted at which point
the second ring on a TRRS connector may short the 2nd ring and sleeve
contacts. Testing has shown that this short-circuit may happen as late
as 500ms after the insertion event, but it never lasts longer then 300ms.
This commit changes the detection algorithm to require 5 identical OVCD
values in a row at 100 ms intervals to fix the jack-type sometimes getting
mis-detected.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt5651_jack_inserted() helper to get the jack-detect switch status,
This is a preparation patch for rewriting the jack type-detection to
make it more reliable.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using RCCLK instead of MCLK / PLL1 the OVCD status often gets stuck
at its last value, which breaks jack-type detection.
This commit fixes this by force-enabling the platform clock when doing
jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the mic-gnd contacts are short-circuited by a headphones plug, the
hardware periodically retries if it can apply the bias-current leading to
the OVCD status flip-flopping 1-0-1 with it being 0 about 10% of the time.
This commit enables the sticky bit for the OVCD status to deal with this.
This commit also introduces 2 helper functions to deal with the OVCD
status bit, this may seem a bit overkill now, but these will also be
used in future patches.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect if
an inserted jack is a headset or headphones (mic shorted to ground).
The threshold for at which current the OVCD triggers on the rt5651 is not
only controlled by setting the absolute current limit, but also by setting
a scale factor which applies to the limit. Testing has shown that we need
to set both (depending on the board).
This commit adds support for the sofar unused OVCD scale-factor register
and adds support for specifying non-default values for it through the
"realtek,over-current-scale-factor" device-property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect
if an inserted jack is a headset or headphones (mic shorted to ground).
Some boards may need different values for the OVCD current threshold
because of a resistor on the board in serial with or parallel to the
jack mic contact.
This commit adds support for configuring the OCVD current threshold
through the "realtek,over-current-threshold-microamp" device-property.
Note this commit changes the default value from 600uA to 2000uA,
because testing has shown 600uA to be a poor default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Configure the jack-detect source through a device-property which can be
set by code outside of the codec driver. Rather then putting platform
specific DMI quirks inside the generic codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The idea behind exporting rt5651_apply_properties(), was for it to be used
on platforms where the platform code may need to add device-properties,
rather then relying only on properties set by the firmware. The platform
code could then call rt5651_apply_properties() after adding properties to
make sure that the codec driver was aware of the new properties.
But this is not necessary, as long as we do all property parsing from
the codec component-driver's probe function (or later) then the machine
driver can attach properties before calling snd_soc_register_card and
calling rt5651_apply_properties() for ordering reasons is not necessary.
This commit makes rt5651_apply_properties() private and adds 2 comments
documenting that all property parsing must be done from the codec
component-driver's probe function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVCD is not only useful for jack-type detection, but is also useful
to protect against over-current faults in general, so always keep
OVCD enabled, instead of only enabling it for jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only configure OVCD once at set_jack time, rather then configuring
it on every jack-insertion event and switch to using bit field defines
instead of hardcoding a magic value.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To determine if a plugged in jack is a headset (speakers + mic) or
headphones (mic contact shorted to ground) we use the micbias1 OVer Current
Detect (OVCD) functionality.
For this to work we need to have a micbias current to actually cause an
overcurrent condition when headphones are plugged in, so jack-type
detection requires both the LDO and micbias1 supplies to be on.
Before this commit there were 2 issues with the handling of this:
1) The LDO supply was force-enabled twice and never disabled again even
though it only needs to be forced on when doing jack-type detection
2) micbias1 was not force-enabled, and thus may be off when doing jack-type
detection
This commit fixes both by force-enabling the LDO and micbias1 supplies
before checking for an overcurrent condition and disabling them afterwards.
Note that both supplies will still get turned on normally (and OVCD will
protect against overcurrent) when the micbias1 is enabled normally because
the user has activated a sound stream recording from the mic.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the "JD power" dapm supply which gets force-enabled once when
using jack-detect and never gets disabled again.
Since the PWR_JD_M bit simply needs to be always on when using jack-detect
there is no need to have it tracked by dapm, instead we can simply set it
to 1 once when initializing the jack-detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that rt5651_set_bias_level(BIAS_OFF) no longer modifies the LDO
voltage selection bits, there is no need to set them each time we move
to standby. Instead configure them once at component-probe() time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the setup of the PWR_ANLG1 reg which was done directly before
calling snd_soc_component_force_bias_level(SND_SOC_BIAS_OFF), as the
latter will override any settings done to PWR_ANLG1 immediately anyways.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, including the jack-detect and PLL power bits. When jack-detection
support was introduced a special case for jack-detect was added which
hard-codes a register value to keep both on.
This commit removes the jack-detect special case, instead simply leaving
these bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PWR_ANLG1 reg not only contains various power on/off bits, it also
contains 2 bits which select if the LDO generates 1.0, 1.1 or 1.2V. Note
there is a separate on/off bit for the LDO.
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, when jack-detection support was introduced a special case for
jack-detect was added which hard-codes a register value to keep the LDO
voltage at 1.2 volt.
This commit removes the jack-detect special case, instead simply always
leaving the LDO voltage control bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5651_set_bias_level() function was turning everything off at
SND_SOC_BIAS_STANDBY, rather then at SND_SOC_BIAS_OFF, requiring the bias-
level to be raised to SND_SOC_BIAS_PREPARE before turning anything on.
This is not how the bias-levels are supposed to work, this commit fixes
this by turning everything off at the SND_SOC_BIAS_OFF level and enabling
the pwr-bits needed for minimum functionality at SND_SOC_BIAS_STANDBY.
This fixes the minimum set of pwr-bits not getting enabled when
force-enabling some dapm-supplies (e.g. for jack type detection),
which raises the bias-level to standby.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5651_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.
RT5651_GBL_CLK is changed by rt5651_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.
This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.
This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5651_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the applying of the differential input and dmic properties to a new
rt5651_apply_properties() helper function. This new function can be called
by platform code which attaches properties after probe() has run to apply
these new properties.
Note this also moves the time when we apply these properties for DT
platforms from i2c-probe to snd-component-probe time, this should not
result in any functional difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the standard component set_jack callback instead of defining a codec
private API for this.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move 2 functions higher up in rt5651.c, this is a preparation patch
to avoid needing forward declarations when moving over from a codec
private function to the standard snd_soc_component_set_jack().
This commit purely moves these 2 functions up, not a single line is
changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all jack-detect initialization to rt5651_set_jack_detect. The main
reason to do this is so that platform code can setup jack-detect properties
after the device has been probed, which unfortunately is necessary on some
platforms.
This has 2 additional advantages:
1) Grouping all jack-detect init together makes it easier to follow what
is happening and results in a small reduction in the number of loc.
2) Before we would register the irq handler before rt5651->hp_jack was
assigned, leading to a potential NULL deref if the jack_detect work runs
before the machine driver has called set_jack.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no in tree users of platform-data for the rt5651 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One of the recently introduced commits hadn't been build tested, fix
that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In usecases like hot plug-unplug DP panel or modeset during a playback,
sometimes we observe no audio after codec resets. During no audio
condition, we have noticed that the power state of the pin or the
connector is D3. Optimizing the way we set the power mitigates the
issue. With this changes the verb is sent to set the power state and
waits until actual state reaches target state. Thus ensuring power
state is set.
Signed-off-by: Abhijeet Kumar <abhijeet.kumar@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges wm5102_compr_platform into soc_codec_dev_wm5102
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges rt5514_spi_dai_component into rt5514_spi_component
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
This patch merges cs47l24_compr_platform into soc_codec_dev_cs47l24
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the merge window having been delayed for another week here's
another batch of updates that came in during that week. There's a few
important fixes in here, mainly a fix for I/O on a number of devices
caused by some of the component rework and a fix for a potential issue
if more than one component in a link provides compressed operations.
The I/O fixes are particularly important as the problem causes a power
regression on a number of OMAP platforms.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlp65E4THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0Oy1B/9XQd6twiSRfNKtbdujOyvjc8lpZ01n
JYHVySXyL9ZqAnIblM7Or/iXVEtsAVcXgFegF3SLHAY6VF7DQ1pDolnxUtuXOxOj
j+/2Y4wnDGCjXEr0tMoxrbNUIqlVZLCpPwsPo3vvVbr6sLLmQYVposNp2A2sK2bz
uWm9E3Nr26Q0UctzjWQM5+AFHSouyL7zDPfBCoWkEToP7163w6r4JDr991KdNGwP
Ac+5qjRUSldsn8WB2ngm8ioqbq+aOvsz2THYjG8gxrlQK+BWsyCDqF7f1d9GWse2
7k+xZLrdJrVkBMOnpvOx/Y4KRfe9BAFZBZ3KRbi2IR++7TD3902xEX27
=aIRm
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound
Pull more ASoC updates from Mark Brown:
"With the merge window having been delayed for another week here's
another batch of updates that came in during that week.
There's a few important fixes in here, mainly a fix for I/O on a
number of devices caused by some of the component rework and a fix for
a potential issue if more than one component in a link provides
compressed operations. The I/O fixes are particularly important as the
problem causes a power regression on a number of OMAP platforms"
* tag 'asoc-v4.16-5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound: (22 commits)
ASoC: stm32: add of dependency for stm32 drivers
ASoC: mt8173-rt5650: fix child-node lookup
ASoC: dapm: fix debugfs read using path->connected
ASoC: compress: Fixup error messages
ASoC: compress: Remove some extraneous blank lines
ASoC: compress: Correct handling of copy callback
ASoC: Intel: kbl: Enable mclk and ssp sclk early
ASoC: Intel: Skylake: Add extended I2S config blob support in Clock driver
ASoC: Intel: Skylake: Add ssp clock driver
ASoC: Fix twl4030 and 6040 regression by adding back read and write
ASoC: sun8i-codec: Add ADC support for a33
ASoC: rockchip: Use dummy_dai for rt5514 dsp dailink
ASoC: soc-pcm: rename .pmdown_time to .use_pmdown_time for Component
ASoC: ak4613: call dummy write for PW_MGMT1/3 when Playback
ASoC: soc-pcm: don't call flush_delayed_work() many times in soc_pcm_private_free()
ASoC: soc-core: snd_soc_rtdcom_lookup() cares component driver name
ASoC: sam9x5_wm8731: Drop 'ASoC' prefix from error messages
ASoC: sam9g20_wm8731: use dev_*() logging functions
ASoC: max98373 Changed SPDX header in C++ comments style
ASoC: dmic: Fix check of return value from read of 'num-channels'
...
Commit 3bb0f7c31b ("ASoC: don't use snd_soc_write/read on twl4030")
caused regressions for both twl4030 and twl6040 as it assumes the
ASoC driver is using regmap. As a side effect, this also causes a
considerable increase in idle power consumption omap3 boards using
twl4030 as the PMIC.
This is because the removal of read and write function pointers
causes some of the ASoC IO functions to not do anything. For example,
snd_soc_register_card() calls snd_soc_dapm_new_widgets() that calls
snd_soc_codec_drv_read() that now does nothing.
A long term solution suggested by Mark Brown <broonie@kernel.org>
is to make the twl drivers use regmap by adding a call to
snd_soc_codec_set_regmap(). This however needs more consideration
as currently the driver internal reads do caching and we would have
both regmap access and internal read/write access accessing the same
hardware registers.
So to fix the regression, let's just do a partial revert adding back
the read and write function pointers. Note that other non-regmap
ASoC drivers may need similar patches.
Fixes: 3bb0f7c31b ("ASoC: don't use snd_soc_write/read on twl4030")
Fixes: 93a00c467f ("ASoC: don't use snd_soc_write/read on twl6040")
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Power Down Release Command (PMVR, PMDAC, RSTN, PMDA1-PMDA6)
which are located on PW_MGMT1 / PW_MGMT3 register must be
write again after at least 5 LRCK cycle or later on each command.
Otherwise, Playback volume will be 0dB.
Basically, it should be
1. PowerDownRelease by Power Management1 <= call 1.x after 5LRCK
1.x Dummy write to Power Management1
2. PowerDownRelease by Power Management3 <= call 2.x after 5LRCK
2.x Dummy write to Power Management3
To avoid too many dummy write, this patch is merging these.
1. PowerDownRelease by Power Management1
2. PowerDownRelease by Power Management3 <= call after 5LRCK
2.x Dummy write to Power Management1/3 <= merge dummy write
This patch adds dummy write when Playback Start timing.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 7fb59e940f ("ASoC: codecs: dmic: Make number of channels
configurable") introduces an optional property to the device tree
to specify the number of DMIC channels. dmic_codec_probe() uses
of_property_read_u32() to read the DT value, and expects a return
value of -ENOENT when the property does not exist. This expectation
is incorrect, the actual value returned in this case is -EINVAL (see
of_find_property_value_of_size(), which is called under the hood).
Check for -EINVAL instead.
Fixes: 7fb59e940f ("ASoC: codecs: dmic: Make number of channels configurable")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "check ER1" message is not very clear about its meaning.
Improve it a bit by referring to it as "ER1 erratum" so that it
becomes clearer that ER1 references to a SGTL5000 erratum.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
