Use kmem_cache_free() to free a buffer allocated with kmem_cache_alloc().
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The 24x7 counters are continuously running and not updated on an
interrupt. So we record the event counts when stopping the event or
deleting it.
But to "read" a single counter in 24x7, we allocate a page and pass it
into the hypervisor (The HV returns the page full of counters from which
we extract the specific counter for this event).
We allocate a page using GFP_USER and when deleting the event, we end up
with the following warning because we are blocking in interrupt context.
[ 698.641709] BUG: scheduling while atomic: swapper/0/0/0x10010000
We could use GFP_ATOMIC but that could result in failures. Pre-allocate
a buffer so we don't have to allocate in interrupt context. Further as
Michael Ellerman suggested, use Per-CPU buffer so we only need to
allocate once per CPU.
Cc: stable@vger.kernel.org
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This still has not been merged and now powerpc is the only arch that does
not have this change. Sorry about missing linuxppc-dev before.
V2->V2
- Fix up to work against 3.18-rc1
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
[mpe: Fix build errors caused by set/or_softirq_pending(), and rework
assignment in __set_breakpoint() to use memcpy().]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Andy reported that the current state of event_idx is rather confused.
So remove all but the x86_pmu implementation and change the default to
return 0 (the safe option).
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Cody P Schafer <dev@codyps.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Himangi Saraogi <himangi774@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: sukadev@linux.vnet.ibm.com <sukadev@linux.vnet.ibm.com>
Cc: Thomas Huth <thuth@linux.vnet.ibm.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux390@de.ibm.com
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
catalog_read() implements the read interface for the sysfs file
/sys/bus/event_source/devices/hv_24x7/interface/catalog
It essentially takes a buffer, an offset and count as parameters
to the read() call. It makes a hypervisor call to read a specific
page from the catalog and copy the required bytes into the given
buffer. Each call to catalog_read() returns at most one 4K page.
Given these requirements, we should be able to simplify the
catalog_read().
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Ian pointed out the use of __aligned(4096) caused rather large stack
consumption in single_24x7_request(), so use the kmem_cache
hv_page_cache (which we've already got set up for other allocations)
insead of allocating locally.
CC: Haren Myneni <hbabu@us.ibm.com>
Reported-by: Ian Munsie <imunsie@au1.ibm.com>
Signed-off-by: Cody P Schafer <dev@codyps.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
ABIv2 kernels are failing to backtrace through the kernel. An example:
39.30% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
__GI___libc_read
The problem is in valid_next_sp() where we check that the new stack
pointer is at least STACK_FRAME_OVERHEAD below the previous one.
ABIv1 has a minimum stack frame size of 112 bytes consisting of 48 bytes
and 64 bytes of parameter save area. ABIv2 changes that to 32 bytes
with no paramter save area.
STACK_FRAME_OVERHEAD is in theory the minimum stack frame size,
but we over 240 uses of it, some of which assume that it includes
space for the parameter area.
We need to work through all our stack defines and rationalise them
but let's fix perf now by creating STACK_FRAME_MIN_SIZE and using
in valid_next_sp(). This fixes the issue:
30.64% readseek2_proce [kernel.kallsyms] [k] find_get_entry
|
--- find_get_entry
pagecache_get_page
generic_file_read_iter
new_sync_read
vfs_read
sys_read
syscall_exit
__GI___libc_read
Cc: stable@vger.kernel.org # 3.16+
Reported-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Free memory allocated using kmem_cache_zalloc using kmem_cache_free
rather than kfree.
The Coccinelle semantic patch that makes this change is as follows:
// <smpl>
@@
expression x,E,c;
@@
x = \(kmem_cache_alloc\|kmem_cache_zalloc\|kmem_cache_alloc_node\)(c,...)
... when != x = E
when != &x
?-kfree(x)
+kmem_cache_free(c,x)
// </smpl>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc updates from Ben Herrenschmidt:
"This is the powerpc new goodies for 3.17. The short story:
The biggest bit is Michael removing all of pre-POWER4 processor
support from the 64-bit kernel. POWER3 and rs64. This gets rid of a
ton of old cruft that has been bitrotting in a long while. It was
broken for quite a few versions already and nobody noticed. Nobody
uses those machines anymore. While at it, he cleaned up a bunch of
old dusty cabinets, getting rid of a skeletton or two.
Then, we have some base VFIO support for KVM, which allows assigning
of PCI devices to KVM guests, support for large 64-bit BARs on
"powernv" platforms, support for HMI (Hardware Management Interrupts)
on those same platforms, some sparse-vmemmap improvements (for memory
hotplug),
There is the usual batch of Freescale embedded updates (summary in the
merge commit) and fixes here or there, I think that's it for the
highlights"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (102 commits)
powerpc/eeh: Export eeh_iommu_group_to_pe()
powerpc/eeh: Add missing #ifdef CONFIG_IOMMU_API
powerpc: Reduce scariness of interrupt frames in stack traces
powerpc: start loop at section start of start in vmemmap_populated()
powerpc: implement vmemmap_free()
powerpc: implement vmemmap_remove_mapping() for BOOK3S
powerpc: implement vmemmap_list_free()
powerpc: Fail remap_4k_pfn() if PFN doesn't fit inside PTE
powerpc/book3s: Fix endianess issue for HMI handling on napping cpus.
powerpc/book3s: handle HMIs for cpus in nap mode.
powerpc/powernv: Invoke opal call to handle hmi.
powerpc/book3s: Add basic infrastructure to handle HMI in Linux.
powerpc/iommu: Fix comments with it_page_shift
powerpc/powernv: Handle compound PE in config accessors
powerpc/powernv: Handle compound PE for EEH
powerpc/powernv: Handle compound PE
powerpc/powernv: Split ioda_eeh_get_state()
powerpc/powernv: Allow to freeze PE
powerpc/powernv: Enable M64 aperatus for PHB3
powerpc/eeh: Aux PE data for error log
...
Pull perf changes from Ingo Molnar:
"Kernel side changes:
- Consolidate the PMU interrupt-disabled code amongst architectures
(Vince Weaver)
- misc fixes
Tooling changes (new features, user visible changes):
- Add support for pagefault tracing in 'trace', please see multiple
examples in the changeset messages (Stanislav Fomichev).
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add header for columns in 'top' and 'report' TUI browsers (Jiri
Olsa)
- Add pagefault statistics in 'trace' (Stanislav Fomichev)
- Add IO mode into timechart command (Stanislav Fomichev)
- Fallback to syscalls:* when raw_syscalls:* is not available in the
perl and python perf scripts. (Daniel Bristot de Oliveira)
- Add --repeat global option to 'perf bench' to be used in benchmarks
such as the existing 'futex' one, that was modified to use it
instead of a local option. (Davidlohr Bueso)
- Fix fd -> pathname resolution in 'trace', be it using /proc or a
vfs_getname probe point. (Arnaldo Carvalho de Melo)
- Add suggestion of how to set perf_event_paranoid sysctl, to help
non-root users trying tools like 'trace' to get a working
environment. (Arnaldo Carvalho de Melo)
- Updates from trace-cmd for traceevent plugin_kvm plus args cleanup
(Steven Rostedt, Jan Kiszka)
- Support S/390 in 'perf kvm stat' (Alexander Yarygin)
Tooling infrastructure changes:
- Allow reserving a row for header purposes in the hists browser
(Arnaldo Carvalho de Melo)
- Various fixes and prep work related to supporting Intel PT (Adrian
Hunter)
- Introduce multiple debug variables control (Jiri Olsa)
- Add callchain and additional sample information for python scripts
(Joseph Schuchart)
- More prep work to support Intel PT: (Adrian Hunter)
- Polishing 'script' BTS output
- 'inject' can specify --kallsym
- VDSO is per machine, not a global var
- Expose data addr lookup functions previously private to 'script'
- Large mmap fixes in events processing
- Include standard stringify macros in power pc code (Sukadev
Bhattiprolu)
Tooling cleanups:
- Convert open coded equivalents to asprintf() (Andy Shevchenko)
- Remove needless reassignments in 'trace' (Arnaldo Carvalho de Melo)
- Cache the is_exit syscall test in 'trace) (Arnaldo Carvalho de
Melo)
- No need to reimplement err() in 'perf bench sched-messaging', drop
barf(). (Davidlohr Bueso).
- Remove ev_name argument from perf_evsel__hists_browse, can be
obtained from the other parameters. (Jiri Olsa)
Tooling fixes:
- Fix memory leak in the 'sched-messaging' perf bench test.
(Davidlohr Bueso)
- The -o and -n 'perf bench mem' options are mutually exclusive, emit
error when both are specified. (Davidlohr Bueso)
- Fix scrollbar refresh row index in the ui browser, problem exposed
now that headers will be added and will be allowed to be switched
on/off. (Jiri Olsa)
- Handle the num array type in python properly (Sebastian Andrzej
Siewior)
- Fix wrong condition for allocation failure (Jiri Olsa)
- Adjust callchain based on DWARF debug info on powerpc (Sukadev
Bhattiprolu)
- Fix a risk for doing free on uninitialized pointer in traceevent
lib (Rickard Strandqvist)
- Update attr test with PERF_FLAG_FD_CLOEXEC flag (Jiri Olsa)
- Enable close-on-exec flag on perf file descriptor (Yann Droneaud)
- Fix build on gcc 4.4.7 (Arnaldo Carvalho de Melo)
- Event ordering fixes (Jiri Olsa)"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (123 commits)
Revert "perf tools: Fix jump label always changing during tracing"
perf tools: Fix perf usage string leftover
perf: Check permission only for parent tracepoint event
perf record: Store PERF_RECORD_FINISHED_ROUND only for nonempty rounds
perf record: Always force PERF_RECORD_FINISHED_ROUND event
perf inject: Add --kallsyms parameter
perf tools: Expose 'addr' functions so they can be reused
perf session: Fix accounting of ordered samples queue
perf powerpc: Include util/util.h and remove stringify macros
perf tools: Fix build on gcc 4.4.7
perf tools: Add thread parameter to vdso__dso_findnew()
perf tools: Add dso__type()
perf tools: Separate the VDSO map name from the VDSO dso name
perf tools: Add vdso__new()
perf machine: Fix the lifetime of the VDSO temporary file
perf tools: Group VDSO global variables into a structure
perf session: Add ability to skip 4GiB or more
perf session: Add ability to 'skip' a non-piped event stream
perf tools: Pass machine to vdso__dso_findnew()
perf tools: Add dso__data_size()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJT1VYNAAoJEHm+PkMAQRiGQJwIAKSYp1Uqz5O/e5r0V1TlZKT4
1B4Njopl57PwSrJQWcGEuH2yHyM896vfPO4L6BJIOfyWzh8kwpQqclDt6uhXoF/v
OsO1zb/7/j+n/pDZsePqP9AyIgErsHEBgUbhecDqzjN++ITPcZjQ6TIMPglZaumN
jFAdAZuAaEwqAk8jqN2wlm689Fh9MuUEarHXbXLCqu5RgLrWhFGhp/cTWY62aqnZ
XfEeQ9KtpRZmlR/IYjerbb1eRH7ZdJsZ88WngLX9dj/JdNxHWBkWQBXGAusXk5Fk
y6LsIV3TjyBdrRKJ1Ifyg/2EIXHNBs8HxTFGXpjtp2HPuMLDxZOWOWikb9URtNg=
=Fjf4
-----END PGP SIGNATURE-----
Merge tag 'v3.16-rc7' into perf/core, to merge in the latest fixes before applying new changes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Power8 has a new register (MMCR2), which contains individual freeze bits
for each counter. This is an improvement on previous chips as it means
we can have multiple events on the PMU at the same time with different
exclude_{user,kernel,hv} settings. Previously we had to ensure all
events on the PMU had the same exclude settings.
The core of the patch is fairly simple. We use the 207S feature flag to
indicate that the PMU backend supports per-event excludes, if it's set
we skip the generic logic that enforces the equality of excludes between
events. We also use that flag to skip setting the freeze bits in MMCR0,
the PMU backend is expected to have handled setting them in MMCR2.
The complication arises with EBB. The FCxP bits in MMCR2 are accessible
R/W to a task using EBB. Which means a task using EBB will be able to
see that we are using MMCR2 for freezing, whereas the old logic which
used MMCR0 is not user visible.
The task can not see or affect exclude_kernel & exclude_hv, so we only
need to consider exclude_user.
The table below summarises the behaviour both before and after this
commit is applied:
exclude_user true false
------------------------------------
| User visible | N N
Before | Can freeze | Y Y
| Can unfreeze | N Y
------------------------------------
| User visible | Y Y
After | Can freeze | Y Y
| Can unfreeze | Y/N Y
------------------------------------
So firstly I assert that the simple visibility of the exclude_user
setting in MMCR2 is a non-issue. The event belongs to the task, and
was most likely created by the task. So the exclude_user setting is not
privileged information in any way.
Secondly, the behaviour in the exclude_user = false case is unchanged.
This is important as it is the case that is actually useful, ie. the
event is created with no exclude setting and the task uses MMCR2 to
implement exclusion manually.
For exclude_user = true there is no meaningful change to freezing the
event. Previously the task could use MMCR2 to freeze the event, though
it was already frozen with MMCR0. With the new code the task can use
MMCR2 to freeze the event, though it was already frozen with MMCR2.
The only real change is when exclude_user = true and the task tries to
use MMCR2 to unfreeze the event. Previously this had no effect, because
the event was already frozen in MMCR0. With the new code the task can
unfreeze the event in MMCR2, but at some indeterminate time in the
future the kernel will overwrite its setting and refreeze the event.
Therefore my final assertion is that any task using exclude_user = true
and also fiddling with MMCR2 was deeply confused before this change, and
remains so after it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To support per-event exclude settings on Power8 we need access to the
struct perf_events in compute_mmcr().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Because we reuse cpuhw->mmcr on each call to compute_mmcr() there's a
risk that we could forget to set one of the values and use whatever
value was in there previously.
Currently all the implementations are careful to set all the values, but
it's safer to clear them all before we call compute_mmcr().
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the recent commit b50a6c584b "Clear MMCR2 when enabling PMU", I
screwed up the handling of MMCR2 for tasks using EBB.
We must make sure we set MMCR2 *before* ebb_switch_in(), otherwise we
overwrite the value of MMCR2 that userspace may have written. That
potentially breaks a task that uses EBB and manually uses MMCR2 for
event freezing.
Fixes: b50a6c584b ("powerpc/perf: Clear MMCR2 when enabling PMU")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are seeing a lot of PMU warnings on POWER8:
Can't find PMC that caused IRQ
Looking closer, the active PMC is 0 at this point and we took a PMU
exception on the transition from negative to 0. Some versions of POWER8
have an issue where they edge detect and not level detect PMC overflows.
A number of places program the PMC with (0x80000000 - period_left),
where period_left can be negative. We can either fix all of these or
just ensure that period_left is always >= 1.
This patch takes the second option.
Cc: <stable@vger.kernel.org>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
On POWER8 when switching to a KVM guest we set bits in MMCR2 to freeze
the PMU counters. Aside from on boot they are then never reset,
resulting in stuck perf counters for any user in the guest or host.
We now set MMCR2 to 0 whenever enabling the PMU, which provides a sane
state for perf to use the PMU counters under either the guest or the
host.
This was manifesting as a bug with ppc64_cpu --frequency:
$ sudo ppc64_cpu --frequency
WARNING: couldn't run on cpu 0
WARNING: couldn't run on cpu 8
...
WARNING: couldn't run on cpu 144
WARNING: couldn't run on cpu 152
min: 18446744073.710 GHz (cpu -1)
max: 0.000 GHz (cpu -1)
avg: 0.000 GHz
The command uses a perf counter to measure CPU cycles over a fixed
amount of time, in order to approximate the frequency of the machine.
The counters were returning zero once a guest was started, regardless of
weather it was still running or had been shut down.
By dumping the value of MMCR2, it was observed that once a guest is
running MMCR2 is set to 1s - which stops counters from running:
$ sudo sh -c 'echo p > /proc/sysrq-trigger'
CPU: 0 PMU registers, ppmu = POWER8 n_counters = 6
PMC1: 5b635e38 PMC2: 00000000 PMC3: 00000000 PMC4: 00000000
PMC5: 1bf5a646 PMC6: 5793d378 PMC7: deadbeef PMC8: deadbeef
MMCR0: 0000000080000000 MMCR1: 000000001e000000 MMCRA: 0000040000000000
MMCR2: fffffffffffffc00 EBBHR: 0000000000000000
EBBRR: 0000000000000000 BESCR: 0000000000000000
SIAR: 00000000000a51cc SDAR: c00000000fc40000 SIER: 0000000001000000
This is done unconditionally in book3s_hv_interrupts.S upon entering the
guest, and the original value is only save/restored if the host has
indicated it was using the PMU. This is okay, however the user of the
PMU needs to ensure that it is in a defined state when it starts using
it.
Fixes: e05b9b9e5c ("powerpc/perf: Power8 PMU support")
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instead of separate bits for every POWER8 PMU feature, have a single one
for v2.07 of the architecture.
This saves us adding a MMCR2 define for a future patch.
Cc: stable@vger.kernel.org
Signed-off-by: Joel Stanley <joel@jms.id.au>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Transition to using the new generic PERF_PMU_CAP_NO_INTERRUPT method for
failing a sampling event when no PMU interrupt is available.
Signed-off-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1406191435440.27913@vincent-weaver-1.umelst.maine.edu
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Cody P Schafer <cody@linux.vnet.ibm.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The catalog version number was changed from a be32 (with proceeding
32bits of padding) to a be64, update the code to treat it as a be64
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
fixup for "powerpc/perf: Add support for the hv gpci (get performance
counter info) interface".
Makes the "not enabled" message less awful (and hidden unless
debugging).
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
fixup for "powerpc/perf: Add support for the hv 24x7 interface"
Makes the "not enabled" message less awful (and hides it in most cases).
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we reject events which have the L3 bank == 1, such as
0x000084918F, because the cache field is non-zero.
However that is incorrect, because although the bank is non-zero, the
value we would write into MMCRC is zero, and so we can count the event.
So fix the check to ignore the bank selector when checking whether the
cache selector is non-zero.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The commit adds a Kconfig option which allows the hv_gpci and hv_24x7
PMUs, added in the preceeding commits, to be built.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This provides a basic interface between hv_24x7 and perf. Similar to
the one provided for gpci, it lacks transaction support and does not
list any events.
Example usage via perf tool:
perf stat -e 'hv_24x7/domain=2,offset=8,starting_index=0,lpar=0xffffffff/' -r 0 -C 0 -x ' ' sleep 0.1
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This provides a basic link between perf and hv_gpci. Notably, it does
not yet support transactions and does not list any events (they can
still be manually composed).
Example usage via perf tool:
perf stat -e 'hv_gpci/counter_info_version=3,offset=0,length=8,secondary_index=0,starting_index=0xffffffff,request=0x10/' -r 0 -C 0 -x ' ' sleep 0.1
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add two macros which generate functions to extract the relevent bits
from event->attr.config{,1,2}.
EVENT_DEFINE_RANGE() defines an accessor for a range of bits in the
event, as well as a "max" function that gives the maximum value of the
field based on the bit width.
EVENT_DEFINE_RANGE_FORMAT() defines the accessor & max routine and also
a format attribute for use in the PMU's attr_groups.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
[mpe: move to powerpc, ugly but descriptive macro names]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This exposes a simple way to grab the firmware provided
collect_priveliged, ga, expanded, and lab capability bits. All of these
bits come in from the same gpci request, so we've exposed all of them.
Only the collect_priveliged bit is really used by the hv-gpci/hv-24x7
code, the other bits are simply exposed in sysfs to inform the user.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
24x7 (also called hv_24x7 or H_24X7) is an interface to obtain
performance counters from the hypervisor. These counters do not have a
fixed format/possition and are instead documented in a "24x7 Catalog",
which is provided by the hypervisor (that interface is also documented
paritialy in the included hv-24x7-catalog.h and fully in at
https://raw.githubusercontent.com/jmesmon/catalog-24x7/master/hv-24x7-catalog.h ).
The 24x7 data access is simply a copy operation into a 4 dimentional
array of 64bit counters (from hypervisor to kernel memory). There is no
interupt triggered on overflow, these are completely disjoint from the
typical power pmu.
This method of obtaining performance counters from the hypervisor is
intended to paritialy replace the gpci interface.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
"H_GetPerformanceCounterInfo" (refered to as hv_gpci or just gpci from
here on) is an interface to retrieve specific performance counters and
other data from the hypervisor. All outputs have a fixed format. This
header only describes the portions of the interface that we plan on
using in linux at this time.
Signed-off-by: Cody P Schafer <cody@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The previous commit added constraint and register handling to allow
processes using EBB (Event Based Branches) to request access to the BHRB
(Branch History Rolling Buffer).
With that in place we can allow processes using EBB to access the BHRB.
This is achieved by setting BHRBA in MMCR0 when we enable EBB access. We
must also clear BHRBA when we are disabling.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We want a way for users of EBB (Event Based Branches) to also access the
BHRB (Branch History Rolling Buffer). EBB does not interoperate with our
existing BHRB support, which is wired into the generic Linux branch
stack sampling support.
To support EBB & BHRB we add three new bits to the event code. The first
bit indicates that the event wants access to the BHRB, and the other two
bits indicate the desired IFM (Instruction Filtering Mode).
We allow multiple events to request access to the BHRB, but they must
agree on the IFM value. Events which are not interested in the BHRB can
also interoperate with events which do.
Finally we program the desired IFM value into MMCRA. Although we do this
for every event, we know that the value will be identical for all events
that request BHRB access.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We only need to mask the EBB bit out of the event for the check of the
special PMC 5 & 6 events. So use a local to do it just for that code,
rather than changing the event value for the life of the function.
While we're there move the set of mask and value after all the checks.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Rather than using PERF_EVENT_CONFIG_EBB_SHIFT everywhere, add an
EVENT_EBB_SHIFT like every other event and use that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Although we already block EBB events which request sampling using
sample_period, technically it's possible for an event to set sample_type
but not sample_period.
Nothing terrible will happen if an EBB event does specify sample_type,
but it signals a major confusion on the part of userspace, and so we do
them the favor of rejecting it.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some power8 revisions have a hardware bug where we can lose a PMU
exception, this commit adds a workaround to detect the bad condition and
rectify the situation.
See the comment in the commit for a full description.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently the sysrq ShowRegs command does not print any PMU registers as
we have an empty definition for perf_event_print_debug(). This patch
defines perf_event_print_debug() to print various PMU registers.
Example output:
CPU: 0 PMU registers, ppmu = POWER7 n_counters = 6
PMC1: 00000000 PMC2: 00000000 PMC3: 00000000 PMC4: 00000000
PMC5: 00000000 PMC6: 00000000 PMC7: deadbeef PMC8: deadbeef
MMCR0: 0000000080000000 MMCR1: 0000000000000000 MMCRA: 0f00000001000000
SIAR: 0000000000000000 SDAR: 0000000000000000 SIER: 0000000000000000
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Fix 32 bit build and rework formatting for compactness]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patchset adds some missing event list for POWER7 PMU raw
events which are exported through sysfs interface. Also updates
the ABI documentation to add all the sysfs exported raw events.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now the config_bhrb() PMU specific call happens after
write_mmcr0(), which actually enables the PMU for event counting and
interrupts. So there is a small window of time where the PMU and BHRB
runs without the required HW branch filter (if any) enabled in BHRB.
This can cause some of the branch samples to be collected through BHRB
without any filter applied and hence affects the correctness of
the results. This patch moves the BHRB config function call before
enabling interrupts.
Here are some data points captured via trace prints which depicts how we
could get PMU interrupts with BHRB filter NOT enabled with a standard
perf record command line (asking for branch record information as well).
$ perf record -j any_call ls
Before the patch:-
ls-1962 [003] d... 2065.299590: .perf_event_interrupt: MMCRA: 40000000000
ls-1962 [003] d... 2065.299603: .perf_event_interrupt: MMCRA: 40000000000
...
All the PMU interrupts before this point did not have the requested
HW branch filter enabled in the MMCRA.
ls-1962 [003] d... 2065.299647: .perf_event_interrupt: MMCRA: 40040000000
ls-1962 [003] d... 2065.299662: .perf_event_interrupt: MMCRA: 40040000000
After the patch:-
ls-1850 [008] d... 190.311828: .perf_event_interrupt: MMCRA: 40040000000
ls-1850 [008] d... 190.311848: .perf_event_interrupt: MMCRA: 40040000000
All the PMU interrupts have the requested HW BHRB branch filter
enabled in MMCRA.
Signed-off-by: Anshuman Khandual <khandual@linux.vnet.ibm.com>
[mpe: Fixed up whitespace and cleaned up changelog]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4df4899 "Add power8 EBB support" included a bug in the handling
of the FAB_CRESP_MATCH and FAB_TYPE_MATCH fields.
These values are pulled out of the event code using EVENT_THR_CTL_SHIFT,
however we were then or'ing that value directly into MMCR1.
This meant we were failing to set the FAB fields correctly, and also
potentially corrupting the value for PMC4SEL. Leading to no counts for
the FAB events and incorrect counts for PMC4.
The fix is simply to shift left the FAB value correctly before or'ing it
with MMCR1.
Reported-by: Sooraj Ravindran Nair <soonair3@in.ibm.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Cc: <stable@vger.kernel.org> # 3.10+
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Pull powerpc updates from Ben Herrenschmidt:
"Here's the powerpc batch for this merge window. Some of the
highlights are:
- A bunch of endian fixes ! We don't have full LE support yet in that
release but this contains a lot of fixes all over arch/powerpc to
use the proper accessors, call the firmware with the right endian
mode, etc...
- A few updates to our "powernv" platform (non-virtualized, the one
to run KVM on), among other, support for bridging the P8 LPC bus
for UARTs, support and some EEH fixes.
- Some mpc51xx clock API cleanups in preparation for a clock API
overhaul
- A pile of cleanups of our old math emulation code, including better
support for using it to emulate optional FP instructions on
embedded chips that otherwise have a HW FPU.
- Some infrastructure in selftest, for powerpc now, but could be
generalized, initially used by some tests for our perf instruction
counting code.
- A pile of fixes for hotplug on pseries (that was seriously
bitrotting)
- The usual slew of freescale embedded updates, new boards, 64-bit
hiberation support, e6500 core PMU support, etc..."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc: Correct FSCR bit definitions
powerpc/xmon: Fix printing of set of CPUs in xmon
powerpc/pseries: Move lparcfg.c to platforms/pseries
powerpc/powernv: Return secondary CPUs to firmware on kexec
powerpc/btext: Fix CONFIG_PPC_EARLY_DEBUG_BOOTX on ppc32
powerpc: Cleanup handling of the DSCR bit in the FSCR register
powerpc/pseries: Child nodes are not detached by dlpar_detach_node
powerpc/pseries: Add mising of_node_put in delete_dt_node
powerpc/pseries: Make dlpar_configure_connector parent node aware
powerpc/pseries: Do all node initialization in dlpar_parse_cc_node
powerpc/pseries: Fix parsing of initial node path in update_dt_node
powerpc/pseries: Pack update_props_workarea to map correctly to rtas buffer header
powerpc/pseries: Fix over writing of rtas return code in update_dt_node
powerpc/pseries: Fix creation of loop in device node property list
powerpc: Skip emulating & leave interrupts off for kernel program checks
powerpc: Add more exception trampolines for hypervisor exceptions
powerpc: Fix location and rename exception trampolines
powerpc: Add more trap names to xmon
powerpc/pseries: Add a warning in the case of cross-cpu VPA registration
powerpc: Update the 00-Index in Documentation/powerpc
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSCDSjAAoJEHm+PkMAQRiGDXMIAI7Loae0Oqb1eoeJkvjyZsBS
OJDeeEcn+k58VbxVHyRdc7hGo4yI4tUZm172SpnOaM8sZ/ehPU7zBrwJK2lzX334
/jAM3uvVPfxA2nu0I4paNpkED/NQ8NRRsYE1iTE8dzHXOH6dA3mgp5qfco50rQvx
rvseXpME4KIAJEq4jnyFZF5+nuHiPueM9JftPmSSmJJ3/KY9kY1LESovyWd7ttg1
jYSVPFal9J0E+tl2UQY5g9H16GqhhjYn+39Iei6Q5P4bL4ZubQgTRQTN9nyDc06Z
ezQtGoqZ8kEz/2SyRlkda6PzjSEhgXlc8mCL5J7AW+dMhTHHx2IrosjiCA80kG8=
=c0rK
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rc5' into perf/core
Merge Linux 3.11-rc5, to sync up with the latest upstream fixes since -rc1.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Address some of the trivial sparse warnings in arch/powerpc.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
e6500 core performance monitors has the following features:
- 6 performance monitor counters
- 512 events supported
- no threshold events
e6500 PMU has more specific events (Data L1 cache misses, Instruction L1
cache misses, etc ) than e500 PMU (which only had Data L1 cache reloads,
etc). Where available, the more specific events have been used which will
produce slightly different results than e500 PMU equivalents.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
