Commit Graph

44 Commits

Author SHA1 Message Date
Archit Taneja
1f5e6247ca ARM: OMAP2/3: VENC hwmods: Remove OCPIF_SWSUP_IDLE flag from VENC slave interface
The clocks for all DSS slave interfaces were recently changed to "dss_ick" on
OMAP2 and OMAP3, this clock can be autoidled by PRCM. The VENC interface
previously had "dss_54m_fck" as it's clock which couldn't be autoidled, and
hence the OCPIF_SWSUP_IDLE flag was needed.

Remove the OCPIF_SWSUP_IDLE flag from VENC interfaces as it's clock is
now "dss_ick".  This allows the PRCM hardware to autoidle the VENC
interface clocks when they are not active, rather than relying on the
software to do it, which can keep the interface clocks active
unnecessarily.

Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: add a short description of the fix to the commit log]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2012-04-13 05:28:34 -06:00
Archit Taneja
b923d40dd4 ARM: OMAP2PLUS: DSS: Ensure DSS works correctly if display is enabled in bootloader
Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.

Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.

Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.

This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.

Thanks to Tomi and Sricharan for some additional testing.

Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: R, Sricharan <r.sricharan@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
 cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-11-08 03:16:46 -07:00
Tomi Valkeinen
b8ac10d8b7 ARM: OMAP2xxx: HWMOD: fix DSS clock data
The OMAP2xxx HWMOD data currently contains two errors with DSS clocks:

- dss_rfbi is missing ick opt-clock, which is needed for RFBI to
  calculate timings

- dss_venc's interface and main clocks are wrong, causing VENC to fail
  to start

These problems were temporarily fixed with a DSS patch
9ede365aa6 ("HACK: OMAP: DSS2: clk hack
for OMAP2/3"), which can be reverted after this patch (and the similar
patches for other OMAPs).

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-11-08 03:16:09 -07:00
Tomi Valkeinen
1258ea596f ARM: OMAP2xxx: HWMOD: Fix DSS reset
DSS needs all DSS clocks to be enabled to be able to finish reset
properly. Before v3.1-rc1 the omapdss driver was managing clocks and
resets correctly. However, when omapdss started using runtime PM at
v3.1-rc1, the responsibility for the reset moved to HWMOD framework.

HWMOD framework does not currently enable all the DSS clocks when
resetting the DSS hardware. This hasn't caused any problems so far, but
we may just have been lucky.

This patch sets HWMOD_CONTROL_OPT_CLKS_IN_RESET for dss_core in OMAP2xxx
HWMOD data, fixing the issue.

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: merged duplicate .flags fields]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-11-08 03:16:09 -07:00
Tarun Kanti DebBarma
c345c8b09d ARM: OMAP2+: dmtimer: convert to platform devices
Add routines to converts dmtimers to platform devices. The device data
is obtained from hwmod database of respective platform and is registered
to device model after successful binding to driver.
In addition, capability attribute of each of the timers is added in
hwmod database.

Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Thara Gopinath <thara@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-09-21 15:50:31 -07:00
Paul Walmsley
d6504acd21 OMAP2+: hwmod: remove OMAP_CHIP*
At Tony's request, remove the OMAP_CHIP* flags from the hwmod data, and
replace it instead with chip family, variant, and ES level-specific lists
of hwmods to register.

Thanks to Gražvydas Ignotas <notasas@gmail.com> for finding a bug in the
AM3517/3505 support, and for other review comments.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Gražvydas Ignotas <notasas@gmail.com>
2011-09-14 17:23:19 -06:00
Avinash.H.M
6d3c55fd4f OMAP: hwmod: fix the i2c-reset timeout during bootup
The sequence of _ocp_softreset doesn't work for i2c. The i2c module has a
special sequence to reset the module. The sequence is
 - Disable the I2C.
 - Write to SOFTRESET bit.
 - Enable the I2C.
 - Poll on the RESETDONE bit.
The sequence is implemented as a function and the i2c_class is updated with
the correct 'reset' pointer.  omap_hwmod_softreset function is implemented
which triggers the softreset by writing into sysconfig register. On following
this sequence, i2c module resets properly and timeouts are not seen.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
[paul@pwsan.com: combined this patch with a patch to remove
 HWMOD_INIT_NO_RESET from the 44xx hwmod flags; change register
 offset conditional code to use the IP block revision; minor code
 cleanup]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-10 05:27:16 -06:00
Andy Green
4d4441a622 I2C: OMAP2+: add correct functionality flags to all omap2plus i2c dev_attr
This adds the new functionality flags for omap i2c unit to all OMAP2
hwmod definitions

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-10 05:27:16 -06:00
Andy Green
db791a7529 I2C: OMAP2+: Tag all OMAP2+ hwmod defintions with I2C IP revision
Since we cannot trust (or even reliably find) the OMAP I2C
peripheral unit's own revision register, we must inform the
OMAP i2c driver of which IP version it is running on.  We
do this by tagging the omap_hwmod_class for i2c on all the
OMAP2+ platform / cpu specific hwmod init and passing it up
to the driver (next patches).

Cc: patches@linaro.org
Cc: Ben Dooks <ben-linux@fluff.org>
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Andy Green <andy.green@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-10 05:27:15 -06:00
Paul Walmsley
273b9465bc omap_hwmod: share identical omap_hwmod_class, omap_hwmod_class_sysconfig arrays
To reduce kernel source file data duplication, share struct
omap_hwmod_class and omap_hwmod_class_sysconfig arrays across OMAP2xxx
and 3xxx hwmod data files.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-09 19:14:08 -06:00
Paul Walmsley
d826ebfa49 omap_hwmod: share identical omap_hwmod_dma_info arrays
To reduce kernel source file data duplication, share struct
omap_hwmod_dma_info arrays across OMAP2xxx and 3xxx hwmod data files.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-09 19:14:07 -06:00
Paul Walmsley
bc6149587b omap_hwmod: use a terminator record with omap_hwmod_dma_info arrays
Previously, struct omap_hwmod_dma_info arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_dma_info
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-09 19:14:07 -06:00
Paul Walmsley
0d619a8999 omap_hwmod: share identical omap_hwmod_mpu_irqs arrays
To reduce kernel source file data duplication, share struct
omap_hwmod_mpu_irqs arrays across OMAP2xxx and 3xxx hwmod data files.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-09 19:14:07 -06:00
Paul Walmsley
212738a449 omap_hwmod: use a terminator record with omap_hwmod_mpu_irqs arrays
Previously, struct omap_hwmod_mpu_irqs arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_mpu_irqs
arrays and uses a sentinel value (irq == -1) as the array terminator
instead.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-09 19:14:06 -06:00
Paul Walmsley
ded11383fc omap_hwmod: share identical omap_hwmod_addr_space arrays
To reduce kernel source file data duplication, share struct
omap_hwmod_addr_space arrays across OMAP2xxx and 3xxx hwmod data
files.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-09 19:14:06 -06:00
Paul Walmsley
78183f3fdf omap_hwmod: use a null structure record to terminate omap_hwmod_addr_space arrays
Previously, struct omap_hwmod_addr_space arrays were unterminated; and
users of these arrays used the ARRAY_SIZE() macro to determine the
length of the array.  However, ARRAY_SIZE() only works when the array
is in the same scope as the macro user.

So far this hasn't been a problem.  However, to reduce duplicated
data, a subsequent patch will move common data to a separate, shared
file.  When this is done, ARRAY_SIZE() will no longer be usable.

This patch removes ARRAY_SIZE() usage for struct omap_hwmod_addr_space
arrays and uses a null structure member as the array terminator
instead.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-07-09 19:14:05 -06:00
Avinash.H.M
f95440ca5b OMAP2/3: hwmod: fix gpio-reset timeouts seen during bootup.
GPIO module expects the debounce clocks to be enabled during reset. It doesn't
reset properly and timeouts are seen, if this clock isn't enabled during
reset. Add the HWMOD_CONTROL_OPT_CLKS_IN_RESET flags to the GPIO HWMODs, with
which the debounce clocks are enabled during reset.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-04-20 12:43:56 -06:00
Benoit Cousson
1286eeb2fd OMAP2+: hwmod data: Fix wrong dma_system end address
OMAP2420, 2430 and 3xxx were using the OMAP4 end address
that unfortunately is not located at the same base address.
Moreover the OMAP4 size was set to 256 instead of 4096.

Change all .pa_end to set them to .pa_start + 0xfff

Cc: "G, Manjunath Kondaiah" <manjugk@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Reported-by: Michael Fillinger <m-fillinger@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-04-19 10:15:36 -06:00
Paul Mundt
da49252fb0 Merge branch 'for-paul' of git://gitorious.org/linux-omap-dss2/linux
Conflicts:
	arch/arm/mach-omap2/board-overo.c

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2011-03-22 14:27:36 +09:00
archit taneja
affe360d13 OMAP: DSS2: Have separate irq handlers for DISPC and DSI
Currently, the core DSS platform device requests for an irq line for OMAP2 and
OMAP3. Make DISPC and DSI platform devices request for a shared IRQ line.

On OMAP3, the logical OR of DSI and DISPC interrupt lines goes to the MPU. There
is a register DSS_IRQSTATUS which tells if the interrupt came from DISPC or DSI.

On OMAP2, there is no DSI, only DISPC interrupts goto the MPU. There is no
DSS_IRQSTATUS register.

Hence, it makes more sense to have separate irq handlers corresponding to the
DSS sub modules instead of having a common handler.

Since on OMAP3 the logical OR of the lines goes to MPU, the irq line is shared
among the IRQ handlers.

The hwmod irq info has been removed for DSS to DISPC and DSI for OMAP2 and OMAP3
hwmod databases. The Probes of DISPC and DSI now request for irq handlers.

Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-03-11 15:46:24 +02:00
Paul Walmsley
2d403fe030 Merge remote branch 'remotes/origin/hwmod_a_2.6.39' into tmp-integration-2.6.39-20110310-024
Conflicts:
	arch/arm/mach-omap2/omap_hwmod_2430_data.c
	arch/arm/mach-omap2/omap_hwmod_3xxx_data.c
	arch/arm/plat-omap/include/plat/omap_hwmod.h
2011-03-10 22:43:05 -07:00
Avinash.H.M
d73d65fab1 omap: hwmod: add syss reset done flags to omap2, omap3 hwmods
Some of the omap2, omap3 peripherals support software reset. This
can be done through the softreset bit in sysconfig register.
The reset status can be checked through resetdone bit of
sysstatus register. syss_has_reset_status is added to the hwmod
database of peripherals which have resetdone bit in sysstatus register.

Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Reviewed-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Avinash.H.M <avinashhm@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2011-03-10 03:23:55 -07:00
Paul Walmsley
c39bee8ac4 OMAP2/3: VENC hwmod: add OCPIF_SWSUP_IDLE flag to interface
According to the hwmod interface data, the DSS submodule "VENC" uses a
clock, "dss_54m_fck"/"dss_tv_fck", which the PRCM cannot autoidle.  By
default, the hwmod code assumes that interface clocks can be autoidled
by the PRCM.  When the interface clock can't be autoidled by the PRCM,
those interfaces must be marked with the OCPIF_SWSUP_IDLE flag.
Otherwise, the "interface clock" will always have a non-zero use
count, and the device won't enter idle.  This problem was observed on
N8x0.

Fix the immediate problem by marking the VENC interface with the
OCPIF_SWSUP_IDLE flag.  But it's not clear that
"dss_54m_fck"/"dss_tv_fck" is really the correct interface clock for
VENC.  It may be that the VENC interface should use a
hardware-autoidling interface clock.  This is the situation on OMAP4,
which uses "l3_div_ck" as the VENC interface clock, which can be
autoidled by the PRCM.  Clarification from TI is needed.

Problem found and patch tested on N8x0 by Tony Lindgren
<tony@atomide.com>.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Senthilvadivu Guruswamy <svadivu@ti.com>
Cc: Sumit Semwal <sumit.semwal@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-03-09 13:03:15 -08:00
Tony Lindgren
b2833a0578 Merge branches 'devel-iommu-mailbox', 'devel-mcbsp', 'devel-board' and 'devel-hsmmc' into omap-for-linus
Conflicts:
	arch/arm/mach-omap2/omap_hwmod_44xx_data.c
2011-03-02 17:11:18 -08:00
Paul Walmsley
550c8092c5 OMAP2+: hwmod: rename some init functions
Rename omap_hwmod_init() to omap_hwmod_register().  Rename
omap_hwmod_late_init() to omap_hwmod_setup_all().  Also change all of
the callers to reflect the new names.  While here, update some
copyrights.

Suggested by Tony Lindgren <tony@atomide.com>.

N.B. The comment in mach-omap2/serial.c may no longer be correct, given
     recent changes in init order.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
2011-02-28 12:04:35 -07:00
Thara Gopinath
eddb12624d OMAP2420: hwmod data: add dmtimer
Add dmtimer data.

Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
2011-02-27 19:11:08 -07:00
Charulatha V
3cb72fa4fe OMAP2420: hwmod data: Add McBSP
Add McBSP hwmod data for OMAP2420.

Also add macros in prcm-common.h for idlest bit of OMAP24XX McBSP devices

Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-02-24 12:51:46 -08:00
Omar Ramirez Luna
fca1ab55f9 OMAP2: hwmod data: add mailbox data
Mailbox hwmod data for omap2430 and 2420.

Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-02-24 12:51:32 -08:00
Senthilvadivu Guruswamy
996746ca12 OMAP2420: hwmod data: add DSS DISPC RFBI VENC
Hwmod needs database of all IPs in a system. This patch generates the hwmod
database for OMAP2420 Display Sub System,. Since DSS is also considered as an
IP as DISPC, RFBI, name it as dss_core.

Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Sumit Semwal <sumit.semwal@ti.com>
Signed-off-by: Senthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
2011-02-23 09:19:06 +02:00
Charulatha V
617871deac OMAP2420: hwmod data: Add McSPI
Update the omap2420 hwmod data with the McSPI info.
Add a device attribute structure which will be used
for passing number of chipselects from hwmod data.
Add revision macros to be passed from rev field from
hwmod.

Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2011-02-17 09:53:09 -08:00
Paul Walmsley
ff2516fbef OMAP2+: wd_timer: disable on boot via hwmod postsetup mechanism
The OMAP watchdog timer IP blocks require a specific set of register
writes to occur before they will be disabled[1], even if the device
clocks appear to be disabled in the CM_*CLKEN registers.  In the MPU
watchdog case, failure to execute this reset sequence will eventually
cause the watchdog to reset the OMAP unexpectedly.

Previously, the code to disable this watchdog was manually called from
mach-omap2/devices.c during device initialization.  This causes the
watchdog to be unconditionally disabled for a portion of kernel
initialization.  This should be controllable by the board-*.c files,
since some system integrators will want full watchdog coverage of
kernel initialization.  Also, the watchdog disable code was not
connected to the hwmod shutdown code.  This means that calling
omap_hwmod_shutdown() will not, in fact, disable the watchdog, and the
goal of omap_hwmod_shutdown() is to be able to shutdown any on-chip
OMAP device.

To resolve the latter problem, populate the pre_shutdown pointer in
the watchdog timer hwmod classes with a function that executes the
watchdog shutdown sequence.  This allows the hwmod code to fully
disable the watchdog.

Then, to allow some board files to support watchdog coverage
throughout kernel initialization, add common code to mach-omap2/io.c
to cause the MPU watchdog to be disabled on boot unless a board file
specifically requests it to remain enabled.  Board files can do this
by changing the watchdog timer hwmod's postsetup state between the
omap2_init_common_infrastructure() and omap2_init_common_devices()
function calls.

1. OMAP34xx Multimedia Device Silicon Revision 3.1.x Rev. ZH
   [SWPU222H], Section 16.4.3.6, "Start/Stop Sequence for WDTs (Using
   WDTi.WSPR Register)"

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Charulatha Varadarajan <charu@ti.com>
2010-12-21 19:57:40 -07:00
G, Manjunath Kondaiah
745685df95 OMAP2420: hwmod data: add system DMA
Add OMAP2420 DMA hwmod data and also add required
DMA device attributes.

Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-12-20 18:38:29 -08:00
Varadarajan, Charulatha
59c348c38f OMAP2420: hwmod data: Add GPIO
Add GPIO hwmod data for OMAP2420 and add the required
GPIO device attributes in the gpio header file

Also remove "omap24xx.h" header file as it is not required
anymore.

Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-12-07 16:26:56 -08:00
Paul Walmsley
2004290f55 OMAP2xxx: hwmod: add I2C hwmods for OMAP2420, 2430
Add hwmod structures for I2C controllers on OMAP2420/2430.

NOTE: I2C module on OMAP2420 has 16bit registers and causes imprecise
aborts if 32bits are read/written to it.  Use the HWMOD_16BIT_REG flag
to notify the hmwod framework of this hard requirement so that
__raw_writew/readw is used to read /write the mdoule registers.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-11-09 09:26:08 -08:00
Kevin Hilman
69758ab7a1 manual merge for pm-hwmod-uart due to conflicts 2010-10-01 13:24:10 -07:00
Kevin Hilman
046465b76a OMAP2/3: UART: add omap_hwmod data for UARTs 1-4
This patch adds omap_hwmod data for UARTs on OMAP2 and OMAP3
platforms.

UART4 support for 3630 and OMAP2 hwmod data added by Govindraj R.

Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-09-29 12:42:42 -07:00
Varadarajan, Charulatha
a714b9cfab OMAP2420: hwmod data: Add watchdog timer
Add watchdog timer hwmod data for OMAP2420 chip

Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
2010-09-29 12:21:57 -07:00
Paul Walmsley
08072acf3a OMAP2: hwmod data: add IVA1 (2420), IVA2 (2430) hwmods
Add IVA1 hwmod data for OMAP2420 and IVA2 hwmod data for 2430.  The data
is based on Benoît Cousson's hwmod data for the OMAP3 IVA blocks.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
2010-07-26 16:34:33 -06:00
Kevin Hilman
4a7cf90a01 OMAP2&3: hwmod: Replace l3 -> l3_main
Replace all the struct that contain l3 with l3_main in order
to be consistent with the OMAP4 naming convention.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-07-26 16:34:32 -06:00
Benoit Cousson
fa98347ebf OMAP2&3: hwmod: Remove _hwmod prefix in name string
In the lastest OMAP4 hwmod data file, the _hwmod was removed
in order to save some memory space and because it does not
bring a lot.
Align OMAP2420, 2430 and 3430 data files with the same convention.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-07-26 16:34:29 -06:00
Kevin Hilman
2eb1875d2b OMAP2/3: hwmod: L3 and L4 CORE/PER/WKUP hwmods don't have IDLEST
Since these hwmods do not have IDLEST, set the HWMOD_NO_IDLEST flag,
otherwise _enable() will fail due to failing _wait_target_ready().

Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
2010-07-26 16:34:28 -06:00
Benoit Cousson
5c2c02961e OMAP: hwmod: Rename hwmod name for the MPU
In the lastest OMAP4 hwmod data file, the _hwmod was removed
in order to save some memory space and because it does not
bring a lot.

The same cleanup will be have to done for other hwmods in
OMAP2 & 3 data files.

Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
2010-05-20 12:31:10 -06:00
Paul Walmsley
43b40992ce OMAP hwmod: add hwmod class support
Add support for categorizing and iterating over hardware IP blocks by
the "class" of the IP block.  The class is the type of the IP block:
e.g., "timer", "timer1ms", etc.  Move the OCP_SYSCONFIG/SYSSTATUS data
from the struct omap_hwmod into the struct omap_hwmod_class, since
it's expected to stay consistent for each class.  While here, fix some
comments.

The hwmod_class structures in this patch were designed and proposed by
Benoît Cousson <b-cousson@ti.com> and were refined in a discussion
between Thara Gopinath <thara@ti.com>, Kevin Hilman
<khilman@deeprootsystems.com>, and myself.

This patch uses WARN() lines that are longer than 80 characters, as
Kevin noted a broader lkml consensus to increase greppability by
keeping the messages all on one line.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Cc: Thara Gopinath <thara@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
2010-02-24 17:45:14 -07:00
Paul Walmsley
7359154e94 OMAP hwmod: convert header files with static allocations into C files
Code should be able to #include any header file without the fear that
the header file will go allocating memory.  This is a coding style
issue, similar to commit 82e9bd5885.
Move the existing hwmod data from .h files to .c files.

While here, convert "omap34xx" to "omap3xxx" in the hwmod files, since
most of these structures should be reusable across all OMAP3 chips.

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
2010-02-24 12:29:45 -07:00