Commit f98a8bf9ee ("KVM: PPC: Book3S HV: Allow KVM_PPC_ALLOCATE_HTAB
ioctl() to change HPT size", 2016-12-20) changed the behaviour of
the KVM_PPC_ALLOCATE_HTAB ioctl so that it now allocates a new HPT
and new revmap array if there was a previously-allocated HPT of a
different size from the size being requested. In this case, we need
to reset the rmap arrays of the memslots, because the rmap arrays
will contain references to HPTEs which are no longer valid. Worse,
these references are also references to slots in the new revmap
array (which parallels the HPT), and the new revmap array contains
random contents, since it doesn't get zeroed on allocation.
The effect of having these stale references to slots in the revmap
array that contain random contents is that subsequent calls to
functions such as kvmppc_add_revmap_chain will crash because they
will interpret the non-zero contents of the revmap array as HPTE
indexes and thus index outside of the revmap array. This leads to
host crashes such as the following.
[ 7072.862122] Unable to handle kernel paging request for data at address 0xd000000c250c00f8
[ 7072.862218] Faulting instruction address: 0xc0000000000e1c78
[ 7072.862233] Oops: Kernel access of bad area, sig: 11 [#1]
[ 7072.862286] SMP NR_CPUS=1024
[ 7072.862286] NUMA
[ 7072.862325] PowerNV
[ 7072.862378] Modules linked in: kvm_hv vhost_net vhost tap xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 nf_conntrack_ipv6 nf_defrag_ipv6 xt_conntrack ip_set nfnetlink ebtable_nat ebtable_broute bridge stp llc ip6table_mangle ip6table_security ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw ebtable_filter ebtables ip6table_filter ip6_tables rpcrdma ib_isert iscsi_target_mod ib_iser libiscsi scsi_transport_iscsi ib_srpt target_core_mod ib_srp scsi_transport_srp ib_ipoib rdma_ucm ib_ucm ib_uverbs ib_umad rdma_cm ib_cm iw_cm iw_cxgb3 mlx5_ib ib_core ses enclosure scsi_transport_sas ipmi_powernv ipmi_devintf ipmi_msghandler powernv_op_panel i2c_opal nfsd auth_rpcgss oid_registry
[ 7072.863085] nfs_acl lockd grace sunrpc kvm_pr kvm xfs libcrc32c scsi_dh_alua dm_service_time radeon lpfc nvme_fc nvme_fabrics nvme_core scsi_transport_fc i2c_algo_bit tg3 drm_kms_helper ptp pps_core syscopyarea sysfillrect sysimgblt fb_sys_fops ttm drm dm_multipath i2c_core cxgb3 mlx5_core mdio [last unloaded: kvm_hv]
[ 7072.863381] CPU: 72 PID: 56929 Comm: qemu-system-ppc Not tainted 4.12.0-kvm+ #59
[ 7072.863457] task: c000000fe29e7600 task.stack: c000001e3ffec000
[ 7072.863520] NIP: c0000000000e1c78 LR: c0000000000e2e3c CTR: c0000000000e25f0
[ 7072.863596] REGS: c000001e3ffef560 TRAP: 0300 Not tainted (4.12.0-kvm+)
[ 7072.863658] MSR: 9000000100009033 <SF,HV,EE,ME,IR,DR,RI,LE,TM[E]>
[ 7072.863667] CR: 44082882 XER: 20000000
[ 7072.863767] CFAR: c0000000000e2e38 DAR: d000000c250c00f8 DSISR: 42000000 SOFTE: 1
GPR00: c0000000000e2e3c c000001e3ffef7e0 c000000001407d00 d000000c250c00f0
GPR04: d00000006509fb70 d00000000b3d2048 0000000003ffdfb7 0000000000000000
GPR08: 00000001007fdfb7 00000000c000000f d0000000250c0000 000000000070f7bf
GPR12: 0000000000000008 c00000000fdad000 0000000010879478 00000000105a0d78
GPR16: 00007ffaf4080000 0000000000001190 0000000000000000 0000000000010000
GPR20: 4001ffffff000415 d00000006509fb70 0000000004091190 0000000ee1881190
GPR24: 0000000003ffdfb7 0000000003ffdfb7 00000000007fdfb7 c000000f5c958000
GPR28: d00000002d09fb70 0000000003ffdfb7 d00000006509fb70 d00000000b3d2048
[ 7072.864439] NIP [c0000000000e1c78] kvmppc_add_revmap_chain+0x88/0x130
[ 7072.864503] LR [c0000000000e2e3c] kvmppc_do_h_enter+0x84c/0x9e0
[ 7072.864566] Call Trace:
[ 7072.864594] [c000001e3ffef7e0] [c000001e3ffef830] 0xc000001e3ffef830 (unreliable)
[ 7072.864671] [c000001e3ffef830] [c0000000000e2e3c] kvmppc_do_h_enter+0x84c/0x9e0
[ 7072.864751] [c000001e3ffef920] [d00000000b38d878] kvmppc_map_vrma+0x168/0x200 [kvm_hv]
[ 7072.864831] [c000001e3ffef9e0] [d00000000b38a684] kvmppc_vcpu_run_hv+0x1284/0x1300 [kvm_hv]
[ 7072.864914] [c000001e3ffefb30] [d00000000f465664] kvmppc_vcpu_run+0x44/0x60 [kvm]
[ 7072.865008] [c000001e3ffefb60] [d00000000f461864] kvm_arch_vcpu_ioctl_run+0x114/0x290 [kvm]
[ 7072.865152] [c000001e3ffefbe0] [d00000000f453c98] kvm_vcpu_ioctl+0x598/0x7a0 [kvm]
[ 7072.865292] [c000001e3ffefd40] [c000000000389328] do_vfs_ioctl+0xd8/0x8c0
[ 7072.865410] [c000001e3ffefde0] [c000000000389be4] SyS_ioctl+0xd4/0x130
[ 7072.865526] [c000001e3ffefe30] [c00000000000b760] system_call+0x58/0x6c
[ 7072.865644] Instruction dump:
[ 7072.865715] e95b2110 793a0020 7b4926e4 7f8a4a14 409e0098 807c000c 786326e4 7c6a1a14
[ 7072.865857] 935e0008 7bbd0020 813c000c 913e000c <93a30008> 93bc000c 48000038 60000000
[ 7072.866001] ---[ end trace 627b6e4bf8080edc ]---
Note that to trigger this, it is necessary to use a recent upstream
QEMU (or other userspace that resizes the HPT at CAS time), specify
a maximum memory size substantially larger than the current memory
size, and boot a guest kernel that does not support HPT resizing.
This fixes the problem by resetting the rmap arrays when the old HPT
is freed.
Fixes: f98a8bf9ee ("KVM: PPC: Book3S HV: Allow KVM_PPC_ALLOCATE_HTAB ioctl() to change HPT size")
Cc: stable@vger.kernel.org # v4.11+
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Commit dc6416f1d7 ("xen/x86: Call
cpu_startup_entry(CPUHP_AP_ONLINE_IDLE) from xen_play_dead()")
introduced an error leading to a stack overflow of the idle task when
a cpu was brought offline/online many times: by calling
cpu_startup_entry() instead of returning at the end of xen_play_dead()
do_idle() would be entered again and again.
Don't use cpu_startup_entry(), but cpuhp_online_idle() instead allowing
to return from xen_play_dead().
Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
CONFIG_BOOTPARAM_HOTPLUG_CPU0 allows to offline CPU0 but Xen HVM guests
BUG() in xen_teardown_timer(). Remove the BUG_ON(), this is probably a
leftover from ancient times when CPU0 hotplug was impossible, it works
just fine for HVM.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Here are some small tty and serial driver fixes for 4.13-rc2. Nothing
huge at all, a revert of a patch that turned out to break things, a fix
up for a new tty ioctl we added in 4.13-rc1 to get the uapi definition
correct, and a few minor serial driver fixes for reported issues.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWXMebA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn9MgCdGsIEQlTvTeG4QikxUPB7dkEJQacAoLWOKJzQ
A65mBAeOfiJztczi8uo4
=KEXp
-----END PGP SIGNATURE-----
Merge tag 'tty-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some small tty and serial driver fixes for 4.13-rc2. Nothing
huge at all, a revert of a patch that turned out to break things, a
fix up for a new tty ioctl we added in 4.13-rc1 to get the uapi
definition correct, and a few minor serial driver fixes for reported
issues.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix TIOCGPTPEER ioctl definition
tty: hide unused pty_get_peer function
tty: serial: lpuart: Fix the logic for detecting the 32-bit type UART
serial: imx: Prevent TX buffer PIO write when a DMA has been started
Revert "serial: imx-serial - move DMA buffer configuration to DT"
serial: sh-sci: Uninitialized variables in sysfs files
serial: st-asc: Potential error pointer dereference
A bunch of small fixes for x86.
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJZcjkKAAoJEED/6hsPKofoo10H/3G0pYtaeKuEtD31hykSMyww
LaZG8+361eY3FD0X5SXJqWMuQXYXGOlbWcOSnArTRgdMIOaeHC50onJAD9sIX7T9
AywGO2RST3Gt83UfvCco47S8gJYs+gHzf5RaFTyvlSmJvDjPGmehjwyVwDWFcVkq
Pdry5jeQ2HvUgvJzphBb/UZHxb82v4haanReHzwRyvexdpApOp5WumgMPFBKMEc4
dVyJ0icgt9o+blSeNRInYezSwi98p0MHPP5xsD1gROXJxb7Hpu7iO3u1r3Z2dKaL
lil0999WCfCMl110ro57L7eC1izfa2B/klhpwo0Q/BJ+tniMfUQWJ54frXRw8XA=
=RzFO
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"A bunch of small fixes for x86"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm: x86: hyperv: avoid livelock in oneshot SynIC timers
KVM: VMX: Fix invalid guest state detection after task-switch emulation
x86: add MULTIUSER dependency for KVM
KVM: nVMX: Disallow VM-entry in MOV-SS shadow
KVM: nVMX: track NMI blocking state separately for each VMCS
KVM: x86: masking out upper bits
A handful of fixes, mostly for new code.
Some reworking of the new STRICT_KERNEL_RWX support to make sure we also remove
executable permission from __init memory before it's freed.
A fix to some recent optimisations to the hypercall entry where we were
clobbering r12, this was breaking nested guests (PR KVM).
A fix for the recent patch to opal_configure_cores(). This could break booting
on bare metal Power8 boxes if the kernel was built without
CONFIG_JUMP_LABEL_FEATURE_CHECK_DEBUG.
And finally a workaround for spurious PMU interrupts on Power9 DD2.
Thanks to:
Nicholas Piggin, Anton Blanchard, Balbir Singh.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Oy4/
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"A handful of fixes, mostly for new code:
- some reworking of the new STRICT_KERNEL_RWX support to make sure we
also remove executable permission from __init memory before it's
freed.
- a fix to some recent optimisations to the hypercall entry where we
were clobbering r12, this was breaking nested guests (PR KVM).
- a fix for the recent patch to opal_configure_cores(). This could
break booting on bare metal Power8 boxes if the kernel was built
without CONFIG_JUMP_LABEL_FEATURE_CHECK_DEBUG.
- .. and finally a workaround for spurious PMU interrupts on Power9
DD2.
Thanks to: Nicholas Piggin, Anton Blanchard, Balbir Singh"
* tag 'powerpc-4.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Mark __init memory no-execute when STRICT_KERNEL_RWX=y
powerpc/mm/hash: Refactor hash__mark_rodata_ro()
powerpc/mm/radix: Refactor radix__mark_rodata_ro()
powerpc/64s: Fix hypercall entry clobbering r12 input
powerpc/perf: Avoid spurious PMU interrupts after idle
powerpc/powernv: Fix boot on Power8 bare metal due to opal_configure_cores()
Pull x86 fixes from Ingo Molnar:
"Half of the fixes are for various build time warnings triggered by
randconfig builds. Most (but not all...) were harmless.
There's also:
- ACPI boundary condition fixes
- UV platform fixes
- defconfig updates
- an AMD K6 CPU init fix
- a %pOF printk format related preparatory change
- .. and a warning fix related to the tlb/PCID changes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/devicetree: Convert to using %pOF instead of ->full_name
x86/platform/uv/BAU: Disable BAU on single hub configurations
x86/platform/intel-mid: Fix a format string overflow warning
x86/platform: Add PCI dependency for PUNIT_ATOM_DEBUG
x86/build: Silence the build with "make -s"
x86/io: Add "memory" clobber to insb/insw/insl/outsb/outsw/outsl
x86/fpu/math-emu: Avoid bogus -Wint-in-bool-context warning
x86/fpu/math-emu: Fix possible uninitialized variable use
perf/x86: Shut up false-positive -Wmaybe-uninitialized warning
x86/defconfig: Remove stale, old Kconfig options
x86/ioapic: Pass the correct data to unmask_ioapic_irq()
x86/acpi: Prevent out of bound access caused by broken ACPI tables
x86/mm, KVM: Fix warning when !CONFIG_PREEMPT_COUNT
x86/platform/uv/BAU: Fix congested_response_us not taking effect
x86/cpu: Use indirect call to measure performance in init_amd_k6()
Pull perf fixes from Ingo Molnar:
"Two hw-enablement patches, two race fixes, three fixes for regressions
of semantics, plus a number of tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/intel: Add proper condition to run sched_task callbacks
perf/core: Fix locking for children siblings group read
perf/core: Fix scheduling regression of pinned groups
perf/x86/intel: Fix debug_store reset field for freq events
perf/x86/intel: Add Goldmont Plus CPU PMU support
perf/x86/intel: Enable C-state residency events for Apollo Lake
perf symbols: Accept zero as the kernel base address
Revert "perf/core: Drop kernel samples even though :u is specified"
perf annotate: Fix broken arrow at row 0 connecting jmp instruction to its target
perf evsel: State in the default event name if attr.exclude_kernel is set
perf evsel: Fix attr.exclude_kernel setting for default cycles:p
Pull core fixes from Ingo Molnar:
"A fix to WARN_ON_ONCE() done by modules, plus a MAINTAINERS update"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
debug: Fix WARN_ON_ONCE() for modules
MAINTAINERS: Update the PTRACE entry
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each device node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: devicetree@vger.kernel.org
Link: http://lkml.kernel.org/r/20170718214339.7774-7-robh@kernel.org
[ Clarify the error message while at it, as 'node' is ambiguous. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have 2 functions using the same sched_task callback:
- PEBS drain for free running counters
- LBR save/store
Both of them are called from intel_pmu_sched_task() and
either of them can be unwillingly triggered when the
other one is configured to run.
Let's say there's PEBS drain configured in sched_task
callback for the event, but in the callback itself
(intel_pmu_sched_task()) we will also run the code for
LBR save/restore, which we did not ask for, but the
code in intel_pmu_sched_task() does not check for that.
This can lead to extra cycles in some perf monitoring,
like when we monitor PEBS event without LBR data.
# perf record --no-timestamp -c 10000 -e cycles:p ./perf bench sched pipe -l 1000000
(We need PEBS, non freq/non timestamp event to enable
the sched_task callback)
The perf stat of cycles and msr:write_msr for above
command before the change:
...
Performance counter stats for './perf record --no-timestamp -c 10000 -e cycles:p \
./perf bench sched pipe -l 1000000' (5 runs):
18,519,557,441 cycles:k
91,195,527 msr:write_msr
29.334476406 seconds time elapsed
And after the change:
...
Performance counter stats for './perf record --no-timestamp -c 10000 -e cycles:p \
./perf bench sched pipe -l 1000000' (5 runs):
18,704,973,540 cycles:k
27,184,720 msr:write_msr
16.977875900 seconds time elapsed
There's no affect on cycles:k because the sched_task happens
with events switched off, however the msr:write_msr tracepoint
counter together with almost 50% of time speedup show the
improvement.
Monitoring LBR event and having extra PEBS drain processing
in sched_task callback showed just a little speedup, because
the drain function does not do much extra work in case there
is no PEBS data.
Adding conditions to recognize the configured work that needs
to be done in the x86_pmu's sched_task callback.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20170719075247.GA27506@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The BAU confers no benefit to a UV system running with only one hub/socket.
Permanently disable the BAU driver if there are less than two hubs online
to avoid BAU overhead. We have observed failed boots on single-socket UV4
systems caused by BAU that are avoided with this patch.
Also, while at it, consolidate initialization error blocks and fix a
memory leak.
Signed-off-by: Andrew Banman <abanman@hpe.com>
Acked-by: Russ Anderson <rja@hpe.com>
Acked-by: Mike Travis <mike.travis@hpe.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: tony.ernst@hpe.com
Link: http://lkml.kernel.org/r/1500588351-78016-1-git-send-email-abanman@hpe.com
[ Minor cleanups. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
They really are, and the "take the address of a single character" makes
the string fortification code unhappy (it believes that you can now only
acccess one byte, rather than a byte range, and then raises errors for
the memory copies going on in there).
We could now remove a few 'addressof' operators (since arrays naturally
degrade to pointers), but this is the minimal patch that just changes
the C prototypes of those template arrays (the templates themselves are
defined in inline asm).
Reported-by: kernel test robot <xiaolong.ye@intel.com>
Acked-and-tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Daniel Micay <danielmicay@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If the SynIC timer message delivery fails due to SINT message slot being
busy, there's no point to attempt starting the timer again until we're
notified of the slot being released by the guest (via EOM or EOI).
Even worse, when a oneshot timer fails to deliver its message, its
re-arming with an expiration time in the past leads to immediate retry
of the delivery, and so on, without ever letting the guest vcpu to run
and release the slot, which results in a livelock.
To avoid that, only start the timer when there's no timer message
pending delivery. When there is, meaning the slot is busy, the
processing will be restarted upon notification from the guest that the
slot is released.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
This can be reproduced by EPT=1, unrestricted_guest=N, emulate_invalid_state=Y
or EPT=0, the trace of kvm-unit-tests/taskswitch2.flat is like below, it tries
to emulate invalid guest state task-switch:
kvm_exit: reason TASK_SWITCH rip 0x0 info 40000058 0
kvm_emulate_insn: 42000:0:0f 0b (0x2)
kvm_emulate_insn: 42000:0:0f 0b (0x2) failed
kvm_inj_exception: #UD (0x0)
kvm_entry: vcpu 0
kvm_exit: reason TASK_SWITCH rip 0x0 info 40000058 0
kvm_emulate_insn: 42000:0:0f 0b (0x2)
kvm_emulate_insn: 42000:0:0f 0b (0x2) failed
kvm_inj_exception: #UD (0x0)
......................
It appears that the task-switch emulation updates rflags (and vm86
flag) only after the segments are loaded, causing vmx->emulation_required
to be set, when in fact invalid guest state emulation is not needed.
This patch fixes it by updating vmx->emulation_required after the
rflags (and vm86 flag) is updated in task-switch emulation.
Thanks Radim for moving the update to vmx__set_flags and adding Paolo's
suggestion for the check.
Suggested-by: Nadav Amit <nadav.amit@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Mike Galbraith reported a situation where a WARN_ON_ONCE() call in DRM
code turned into an oops. As it turns out, WARN_ON_ONCE() seems to be
completely broken when called from a module.
The bug was introduced with the following commit:
19d436268d ("debug: Add _ONCE() logic to report_bug()")
That commit changed WARN_ON_ONCE() to move its 'once' logic into the bug
trap handler. It requires a writable bug table so that the BUGFLAG_DONE
bit can be written to the flags to indicate the first warning has
occurred.
The bug table was made writable for vmlinux, which relies on
vmlinux.lds.S and vmlinux.lds.h for laying out the sections. However,
it wasn't made writable for modules, which rely on the ELF section
header flags.
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 19d436268d ("debug: Add _ONCE() logic to report_bug()")
Link: http://lkml.kernel.org/r/a53b04235a65478dd9afc51f5b329fdc65c84364.1500095401.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have space for exactly three characters for the index in "max7315_%d_base",
but as GCC points out having more would cause an string overflow:
arch/x86/platform/intel-mid/device_libs/platform_max7315.c: In function 'max7315_platform_data':
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:26: error: '%d' directive writing between 1 and 11 bytes into a region of size 9 [-Werror=format-overflow=]
sprintf(base_pin_name, "max7315_%d_base", nr);
^~~~~~~~~~~~~~~~~
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:26: note: directive argument in the range [-2147483647, 2147483647]
arch/x86/platform/intel-mid/device_libs/platform_max7315.c:41:3: note: 'sprintf' output between 15 and 25 bytes into a destination of size 17
sprintf(base_pin_name, "max7315_%d_base", nr);
This makes it use an snprintf() to truncate the string if that happened
rather than overflowing the stack. In practice, this is safe, because
there won't be a large number of max7315 devices in the systems, and
both the format and the length are defined by the firmware interface.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-9-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The IOSF_MBI option requires PCI support, without it we get a harmless
Kconfig warning when it gets selected by PUNIT_ATOM_DEBUG:
warning: (X86_INTEL_LPSS && SND_SST_IPC_ACPI && MMC_SDHCI_ACPI && PUNIT_ATOM_DEBUG) selects IOSF_MBI which has unmet direct dependencies (PCI)
This adds another dependency to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-8-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Every kernel build on x86 will result in some output:
Setup is 13084 bytes (padded to 13312 bytes).
System is 4833 kB
CRC 6d35fa35
Kernel: arch/x86/boot/bzImage is ready (#2)
This shuts it up, so that 'make -s' is truely silent as long as
everything works. Building without '-s' should produce unchanged
output.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-6-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The x86 version of insb/insw/insl uses an inline assembly that does
not have the target buffer listed as an output. This can confuse
the compiler, leading it to think that a subsequent access of the
buffer is uninitialized:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_mgmt_scan_confirm’:
drivers/net/wireless/wl3501_cs.c:665:9: error: ‘sig.status’ is used uninitialized in this function [-Werror=uninitialized]
drivers/net/wireless/wl3501_cs.c:668:12: error: ‘sig.cap_info’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c: In function 'sb1000_rx':
drivers/net/sb1000.c:775:9: error: 'st[0]' is used uninitialized in this function [-Werror=uninitialized]
drivers/net/sb1000.c:776:10: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/sb1000.c:784:11: error: 'st[1]' may be used uninitialized in this function [-Werror=maybe-uninitialized]
I tried to mark the exact input buffer as an output here, but couldn't
figure it out. As suggested by Linus, marking all memory as clobbered
however is good enough too. For the outs operations, I also add the
memory clobber, to force the input to be written to local variables.
This is probably already guaranteed by the "asm volatile", but it can't
hurt to do this for symmetry.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Link: http://lkml.kernel.org/r/20170719125310.2487451-5-arnd@arndb.de
Link: https://lkml.org/lkml/2017/7/12/605
Signed-off-by: Ingo Molnar <mingo@kernel.org>
gcc-7.1.1 produces this warning:
arch/x86/math-emu/reg_add_sub.c: In function 'FPU_add':
arch/x86/math-emu/reg_add_sub.c:80:48: error: ?: using integer constants in boolean context [-Werror=int-in-bool-context]
This appears to be a bug in gcc-7.1.1, and I have reported it as
PR81484. The compiler suggests that code written as
if (a & b ? c : d)
is usually incorrect and should have been
if (a & (b ? c : d))
However, in this case, we correctly write
if ((a & b) ? c : d)
and should not get a warning for it.
This adds a dirty workaround for the problem, adding a comparison with
zero inside of the macro. The warning is currently disabled in the kernel,
so we may decide not to apply the patch, and instead wait for future gcc
releases to fix the problem. On the other hand, it seems to be the
only instance of this particular problem.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Bill Metzenthen <billm@melbpc.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-4-arnd@arndb.de
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=81484
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When building the kernel with "make EXTRA_CFLAGS=...", this overrides
the "PARANOID" preprocessor macro defined in arch/x86/math-emu/Makefile,
and we run into a build warning:
arch/x86/math-emu/reg_compare.c: In function ‘compare_i_st_st’:
arch/x86/math-emu/reg_compare.c:254:6: error: ‘f’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
This fixes the implementation to work correctly even without the PARANOID
flag, and also fixes the Makefile to not use the EXTRA_CFLAGS variable
but instead use the ccflags-y variable in the Makefile that is meant
for this purpose.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Bill Metzenthen <billm@melbpc.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-3-arnd@arndb.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The intialization function checks for various failure scenarios, but
unfortunately the compiler gets a little confused about the possible
combinations, leading to a false-positive build warning when
-Wmaybe-uninitialized is set:
arch/x86/events/core.c: In function ‘init_hw_perf_events’:
arch/x86/events/core.c:264:3: warning: ‘reg_fail’ may be used uninitialized in this function [-Wmaybe-uninitialized]
arch/x86/events/core.c:264:3: warning: ‘val_fail’ may be used uninitialized in this function [-Wmaybe-uninitialized]
pr_err(FW_BUG "the BIOS has corrupted hw-PMU resources (MSR %x is %Lx)\n",
We can't actually run into this case, so this shuts up the warning
by initializing the variables to a known-invalid state.
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170719125310.2487451-2-arnd@arndb.de
Link: https://patchwork.kernel.org/patch/9392595/
Signed-off-by: Ingo Molnar <mingo@kernel.org>
One of the rarely executed code pathes in check_timer() calls
unmask_ioapic_irq() passing irq_get_chip_data(0) as argument.
That's wrong as unmask_ioapic_irq() expects a pointer to the irq data of
interrupt 0. irq_get_chip_data(0) returns NULL, so the following
dereference in unmask_ioapic_irq() causes a kernel panic.
The issue went unnoticed in the first place because irq_get_chip_data()
returns a void pointer so the compiler cannot do a type check on the
argument. The code path was added for machines with broken configuration,
but it seems that those machines are either not running current kernels or
simply do not longer exist.
Hand in irq_get_irq_data(0) as argument which provides the correct data.
[ tglx: Rewrote changelog ]
Fixes: 4467715a44 ("x86/irq: Move irq_cfg.irq_2_pin into io_apic.c")
Signed-off-by: Seunghun Han <kkamagui@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1500369644-45767-1-git-send-email-kkamagui@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The bus_irq argument of mp_override_legacy_irq() is used as the index into
the isa_irq_to_gsi[] array. The bus_irq argument originates from
ACPI_MADT_TYPE_IO_APIC and ACPI_MADT_TYPE_INTERRUPT items in the ACPI
tables, but is nowhere sanity checked.
That allows broken or malicious ACPI tables to overwrite memory, which
might cause malfunction, panic or arbitrary code execution.
Add a sanity check and emit a warning when that triggers.
[ tglx: Added warning and rewrote changelog ]
Signed-off-by: Seunghun Han <kkamagui@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: security@kernel.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: stable@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
randstruct plugin, including the task_struct.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=ngAW
-----END PGP SIGNATURE-----
Merge tag 'gcc-plugins-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull structure randomization updates from Kees Cook:
"Now that IPC and other changes have landed, enable manual markings for
randstruct plugin, including the task_struct.
This is the rest of what was staged in -next for the gcc-plugins, and
comes in three patches, largest first:
- mark "easy" structs with __randomize_layout
- mark task_struct with an optional anonymous struct to isolate the
__randomize_layout section
- mark structs to opt _out_ of automated marking (which will come
later)
And, FWIW, this continues to pass allmodconfig (normal and patched to
enable gcc-plugins) builds of x86_64, i386, arm64, arm, powerpc, and
s390 for me"
* tag 'gcc-plugins-v4.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
randstruct: opt-out externally exposed function pointer structs
task_struct: Allow randomized layout
randstruct: Mark various structs for randomization
KVM tries to select 'TASKSTATS', which had additional dependencies:
warning: (KVM) selects TASKSTATS which has unmet direct dependencies (NET && MULTIUSER)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Immediately following MOV-to-SS/POP-to-SS, VM-entry is
disallowed. This check comes after the check for a valid VMCS. When
this check fails, the instruction pointer should fall through to the
next instruction, the ALU flags should be set to indicate VMfailValid,
and the VM-instruction error should be set to 26 ("VM entry with
events blocked by MOV SS").
Signed-off-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
vmx_recover_nmi_blocking is using a cached value of the guest
interruptibility info, which is stored in vmx->nmi_known_unmasked.
vmx_recover_nmi_blocking is run for both normal and nested guests,
so the cached value must be per-VMCS.
This fixes eventinj.flat in a nested non-EPT environment. With EPT it
works, because the EPT violation handler doesn't have the
vmx->nmi_known_unmasked optimization (it is unnecessary because, unlike
vmx_recover_nmi_blocking, it can just look at the exit qualification).
Thanks to Wanpeng Li for debugging the testcase and providing an initial
patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
kvm_read_cr3() returns an unsigned long and gfn is a u64. We intended
to mask out the bottom 5 bits but because of the type issue we mask the
top 32 bits as well. I don't know if this is a real problem, but it
causes static checker warnings.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
There's a bug in PEBs event enabling code, that prevents PEBS
freq events to work properly after non freq PEBS event was run.
freq events - perf_event_attr::freq set
-F <freq> option of perf record
PEBS events - perf_event_attr::precise_ip > 0
default for perf record
Like in following example with CPU 0 busy, we expect ~10000 samples
for following perf tool run:
# perf record -F 10000 -C 0 sleep 1
[ perf record: Woken up 2 times to write data ]
[ perf record: Captured and wrote 0.640 MB perf.data (10031 samples) ]
Everything's fine, but once we run non freq PEBS event like:
# perf record -c 10000 -C 0 sleep 1
[ perf record: Woken up 4 times to write data ]
[ perf record: Captured and wrote 1.053 MB perf.data (20061 samples) ]
the freq events start to fail like this:
# perf record -F 10000 -C 0 sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.185 MB perf.data (40 samples) ]
The issue is in non freq PEBs event initialization of debug_store reset
field, which value is used to auto-reload the counter value after PEBS
event drain. This value is not being used for PEBS freq events, but once
we run non freq event it stays in debug_store data and screws the
sample_freq counting for PEBS freq events.
Setting the reset field to 0 for freq events.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170714163551.19459-1-jolsa@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add perf core PMU support for Intel Goldmont Plus CPU cores:
- The init code is based on Goldmont.
- There is a new cache event list, based on the Goldmont cache event
list.
- All four general-purpose performance counters support PEBS.
- The first general-purpose performance counter is for reduced skid
PEBS mechanism. Using :ppp to indicate the event which want to do
reduced skid PEBS.
- Goldmont Plus has 4-wide pipeline for Topdown
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Link: http://lkml.kernel.org/r/20170712134423.17766-1-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Goldmont microarchitecture supports C1/C3/C6, PC2/PC3/PC6/PC10 state
residency counters, the patch enables them for Apollo Lake platform.
The MSR information is based on Intel Software Developers' Manual,
Vol. 4, Order No. 335592, Table 2-6 and 2-12.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: bp@suse.de
Cc: davidcc@google.com
Cc: gs0622@gmail.com
Cc: lukasz.odzioba@intel.com
Cc: piotr.luc@intel.com
Cc: srinivas.pandruvada@linux.intel.com
Link: http://lkml.kernel.org/r/20170717103749.24337-1-harry.pan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently even with STRICT_KERNEL_RWX we leave the __init text marked
executable after init, which is bad.
Add a hook to mark it NX (no-execute) before we free it, and implement
it for radix and hash.
Note that we use __init_end as the end address, not _einittext,
because overlaps_kernel_text() uses __init_end, because there are
additional executable sections other than .init.text between
__init_begin and __init_end.
Tested on radix and hash with:
0:mon> p $__init_begin
*** 400 exception occurred
Fixes: 1e0fc9d1eb ("powerpc/Kconfig: Enable STRICT_KERNEL_RWX for some configs")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the core logic into a helper, so we can use it for changing other
permissions.
We also change the logic to align start down, and end up. This means
calling the function with a range will expand that range to be at
least 1 mmu_linear_psize page in size. We need that so we can use it
on __init_begin ... __init_end which is not a full page in size.
This should always work for _stext/__init_begin, because we align
__init_begin to _stext + 16M in the linker script.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Move the core logic into a helper, so we can use it for changing permissions
other than _PAGE_WRITE.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
A recent commit:
d6e41f1151 ("x86/mm, KVM: Teach KVM's VMX code that CR3 isn't a constant")
introduced a VM_WARN_ON(!in_atomic()) which generates false positives
on every VM entry on !CONFIG_PREEMPT_COUNT kernels.
Replace it with a test for preemptible(), which appears to match the
original intent and works across different CONFIG_PREEMPT* variations.
Signed-off-by: Roman Kagan <rkagan@virtuozzo.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Nadav Amit <nadav.amit@gmail.com>
Cc: Nadav Amit <namit@vmware.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Cc: linux-mm@kvack.org
Fixes: d6e41f1151 ("x86/mm, KVM: Teach KVM's VMX code that CR3 isn't a constant")
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A previous optimisation incorrectly assumed the PAPR hcall does
not use r12, and clobbers it upon entry. In fact it is used as
an input. This can result in KVM guests crashing (observed with
PR KVM).
Instead of using r12 to save r13, tihs patch saves r13 in ctr.
This is more costly, but not as slow as using the SPRG.
Fixes: acd7d8cef0 ("powerpc/64s: Optimize hypercall/syscall entry")
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
POWER9 DD2 can see spurious PMU interrupts after state-loss idle in
some conditions.
A solution is to save and reload MMCR0 over state-loss idle.
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Acked-by: Madhavan Srinivasan <maddy@linux.vnet.ibm.com>
Tested-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Pull sparc fixes from David Miller:
- Fix DMA regression in 4.13 merge window, only certain chips can do
64-bit DMA. From Dave Dushar.
- Correct cpu cross-call algorithm to correctly detect stalled or stuck
remote cpus, from Jane Chu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Measure receiver forward progress to avoid send mondo timeout
SPARC64: Fix sun4v DMA panic
Several variables had their types changed from unsigned long to u32,
but the printk()-style format to print them wasn't updated, leading to:
arch/blackfin/kernel/flat.c: In function 'bfin_get_addr_from_rp':
arch/blackfin/kernel/flat.c:35:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'u32' [-Wformat]
arch/blackfin/kernel/flat.c: In function 'bfin_put_addr_at_rp':
arch/blackfin/kernel/flat.c:80:3: warning: format '%lx' expects argument of type 'long unsigned int', but argument 2 has type 'u32' [-Wformat]
Fixes: 468138d785 ("binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This ioctl does nothing to justify an _IOC_READ or _IOC_WRITE flag
because it doesn't copy anything from/to userspace to access the
argument.
Fixes: 54ebbfb160 ("tty: add TIOCGPTPEER ioctl")
Signed-off-by: Gleb Fotengauer-Malinovskiy <glebfm@altlinux.org>
Acked-by: Aleksa Sarai <asarai@suse.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In commit 1c0eaf0f56 ("powerpc/powernv: Tell OPAL about our MMU mode
on POWER9"), we added additional flags to the OPAL call to configure
CPUs at boot.
These flags only work on Power9 firmwares, and worse can cause boot
failures on Power8 machines, so we check for CPU_FTR_ARCH_300 (aka POWER9)
before adding the extra flags.
Unfortunately we forgot that opal_configure_cores() is called before
the CPU feature checks are dynamically patched, meaning the check
always returns true.
We definitely need to do something to make the CPU feature checks less
prone to bugs like this, but for now the minimal fix is to use
early_cpu_has_feature().
Reported-and-tested-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Fixes: 1c0eaf0f56 ("powerpc/powernv: Tell OPAL about our MMU mode on POWER9")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In file included from include/linux/flat.h:13:0,
from fs/binfmt_flat.c:36:
arch/h8300/include/asm/flat.h: In function 'flat_get_addr_from_rp':
arch/h8300/include/asm/flat.h:28:3: error: expected ')' before 'val'
val &= 0x00ffffff;
^
arch/h8300/include/asm/flat.h:31:1: error: expected expression before '}' token
}
^
In file included from include/linux/flat.h:13:0,
from fs/binfmt_flat.c:36:
arch/h8300/include/asm/flat.h:26:6: warning: unused variable 'val' [-Wunused-variable]
u32 val = get_unaligned((__force u32 *)rp);
^
In file included from include/linux/flat.h:13:0,
from fs/binfmt_flat.c:36:
arch/h8300/include/asm/flat.h:31:1: warning: no return statement in function returning non-void [-Wreturn-type]
}
^
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 468138d785 ("binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several variables had their types changed from unsigned long to u32, but
the arch-specific implementations of flat_set_persistent() weren't
updated, leading to compiler warnings on blackfin and m68k:
fs/binfmt_flat.c: In function ‘load_flat_file’:
fs/binfmt_flat.c:799: warning: passing argument 2 of ‘flat_set_persistent’ from incompatible pointer type
Fixes: 468138d785 ("binfmt_flat: flat_{get,put}_addr_from_rp() should be able to fail")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug fix for the BAU tunable congested_cycles not being set to the user
defined value. Instead of referencing a global variable when deciding
on BAU shutdown, a node will reference its own tunable set
value ( cong_response_us). This results in the user set
tunable value congested_response_us taking effect correctly.
Signed-off-by: Justin Ernst <justin.ernst@hpe.com>
Acked-by: Andrew Banman <abanman@hpe.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: mike.travis@hpe.com
Cc: sivanich@hpe.com
Link: http://lkml.kernel.org/r/1499970803-282432-1-git-send-email-justin.ernst@hpe.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This old piece of code is supposed to measure the performance of indirect
calls to determine if the processor is buggy or not, however the compiler
optimizer turns it into a direct call.
Use the OPTIMIZER_HIDE_VAR() macro to thwart the optimization, so that a real
indirect call is generated.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1707110737530.8746@file01.intranet.prod.int.rdu2.redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull ->s_options removal from Al Viro:
"Preparations for fsmount/fsopen stuff (coming next cycle). Everything
gets moved to explicit ->show_options(), killing ->s_options off +
some cosmetic bits around fs/namespace.c and friends. Basically, the
stuff needed to work with fsmount series with minimum of conflicts
with other work.
It's not strictly required for this merge window, but it would reduce
the PITA during the coming cycle, so it would be nice to have those
bits and pieces out of the way"
* 'work.mount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
isofs: Fix isofs_show_options()
VFS: Kill off s_options and helpers
orangefs: Implement show_options
9p: Implement show_options
isofs: Implement show_options
afs: Implement show_options
affs: Implement show_options
befs: Implement show_options
spufs: Implement show_options
bpf: Implement show_options
ramfs: Implement show_options
pstore: Implement show_options
omfs: Implement show_options
hugetlbfs: Implement show_options
VFS: Don't use save/replace_mount_options if not using generic_show_options
VFS: Provide empty name qstr
VFS: Make get_filesystem() return the affected filesystem
VFS: Clean up whitespace in fs/namespace.c and fs/super.c
Provide a function to create a NUL-terminated string from unterminated data
