The KIANO SlimNote 14.2 laptop uses the JD1_1 input pin for jack
detection. Set the correct quirk in the codec driver.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rework a bit the quirk logic in the codec driver to simplify the
DMI-based quirk assignment for non-DT platforms.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable jack detection for the RT5651 codec on the JD* pins.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation for unconditionally passing the struct timer_list
pointer to all timer callbacks, switch to using the new timer_setup()
and from_timer() to pass the timer pointer explicitly. These are all the
"mechanical" changes remaining in the sound subsystem.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Enable jack detection for the RT5651 codec on the JD* pins.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of failure in loading customize topology firmware, dfw_sst.bin
gets loaded. However, current log provides this message as error even
after successfully falling back to default topology "dfw_sst.bin".
Hence to convey proper message, changing log level and message.
Signed-off-by: Chintan Patel <chintan.m.patel@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Codec will be replaced into Component, then Codec side
doesn't use legacy_dai_naming on snd_soc_register_dais().
This patch adds new non_legacy_dai_naming flag on Component driver
and use converted its value for snd_soc_register_dais().
When Codec is replaced into Component, Codec driver needs
to have non_legacy_dai_naming = 1 flags.
Existing CPU side of course doesn't have this flag, thus CPU calls
it as true.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec will be replaced into Component, then Codec side only
needs to call fixup_codec_formats() at this point.
This patch adds new endianness flag on Component driver
and call convert_endianness_formats() (= was fixup_codec_format())
if endianness was true.
When Codec is replaced into Component, Codec driver needs
to have endianness = 1 flags.
Existing CPU side of course doesn't have this flag, thus CPU doesn't
call it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current snd_soc_runtime_ignore_pmdown_time() tallys all Codec and
CPU's "ignore_pmdown_time". Now, CPU (= via compoent)
ignore_pmdown_time is fixed as "true". Codec's one is copied from Codec
driver. This means Codec side default is "false".
Current all Codec driver will be replaced into Component, thus, we can
use for_each_rtdcom() for this totalization. This patch adds new
"pmdown_time" on Component driver. Its inverted value will be used
for this "ignore" totalizaton.
Of course all existing Component driver doesn't have its settings now,
thus, all existing "pmdown_time" is "false". This means all
Components will ignore pmdown time. This is current CPU behavior.
To keep compatibility, snd_soc_runtime_ignore_pmdown_time() totalize
Component's inverted "pmdown_time" (= total will be true) and
Codec's "ignore_pmdown_time" (= depends on Codec driver settings).
Because It is using AND operation, its result is based on Codec driver
settings only.
This means this operation can keep compatibility and doesn't have
nonconformity.
When we replace Codec to Component, the driver which has
".ignore_pmdown_time = true" will be just removed,
and the driver which doesn't have it will have new
".pmdown_time = true".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Platform will be replaced into Component in the future.
snd_soc_platform_driver has snd_compr_ops, but snd_soc_component_driver
doesn't have. To prepare for replacing, this patch adds snd_compr_ops on
component driver.
platform will be replaced into component, and its code will be removed.
But during replacing, both platform and component process code exists.
To keep compatibility, to avoid platform NULL access and to avoid
platform/component duplicate operation during replacing process, this
patch has such code. Some of this code will be removed when platform was
removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Platform will be replaced into Component in the future.
snd_soc_platform_driver has snd_pcm_ops, but snd_soc_component_driver
doesn't have it. To prepare for replacing, this patch adds snd_pcm_ops
on component driver.
platform will be replaced into component, and its code will be removed.
But during replacing, both platform and component process code exists.
To keep compatibility, to avoid platform NULL access and to avoid
platform/component duplicate operation during replacing process, this
patch has such code. Some of this code will be removed when platform was
removed.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MICBIAS widget type has been deprecated. Convert it to a SUPPLY widget.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make all Intel audio drivers dependent on X86 to avoid compilation
errors for s390 and xtensa architectures.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce more logical dependencies, with the SOC selected first and the
relevant machine drivers are exposed.
The same mechanism will be used for SOF support.
Also select SND_SOC_ACPI_INTEL_MATCH for all machine drivers
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This file is a mess, order by generation with more recent last
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
split Kconfig to prepare for reuse of machine drivers for
SOF support
no functional change or edits
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prepare for SOF integration, no functional change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
First step of cleaning, move all tables to soc-acpi-intel-match module.
The tables remain in separate files per platform to keep them
manageable. Skylake+ platforms are still handled elsewhere since
there is no conflict with SOF for now, but this will have to be
handled at a later point.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before we add new fields for SOF support, move to C99 syntax
as done for atom/sst and legacy hsw/bdw code
No functional change
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ACPI support is not specific to the Intel/SST driver. Move the enumeration
and matching code which is not hardware-dependent to sound/soc and rename
relevant sst_acpi_ structures and functions with snd_soc_acpi_ prefix
soc-acpi.h is protected by a #ifndef __LINUX_SND_SOC_ACPI_H for
consistency with all other SoC .h files:
grep -L __LINUX include/sound/soc* | wc -l
0
grep __LINUX include/sound/soc* | wc -l
14
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clear IRQ mask on stream stop to avoid spurious IRQs.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio interface direction and protocol settings does not change
at runtime. So, these settings are moved from hw_params
function to dai_probe and set_fmt.
Signed-off-by: olivier moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm version of reset_control_get function
to manage driver removing properly.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set best burst size tradeoff for 8, 16, 32 bits transfers.
Signed-off-by: olivier moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a new custom dapm routes map to quirk platforms with the
internal mic connected to IN2P.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer dma_dev_name is assigned but never read, it is redundant
and can therefore be removed.
Cleans up clang warning:
sound/soc/intel/common/sst-firmware.c:288:3: warning: Value stored to
'dma_dev_name' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value of register 0x91 is 0x0c00 instead of 0x0000.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is used for AMD board using rt5650 codec.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Stoney uses 16kb SRAM memory for playback and 16Kb
for capture.Modified Max buffer size to have the
correct mapping between System Memory and SRAM.
Added snd_pcm_hardware structures for playback
and capture for Stoney.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Added DMA driver changes for Stoney platform.
Below are the key differences between Stoney and CZ
In Stoney, Memory Gating is disabled.SRAM Banks won't
be turned off.No Of SRAM Banks reduced to 6.
DAGB Garlic Interface used and 16 bit resolution is supported.
SRAM bank 1 & SRAM bank 2 will be used for playback scenario.
SRAM Bank 3 & SRAM Bank 4 will be used for Capture scenario.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For Stoney platform, Memory gating is disabled.i.e SRAM Banks
won't be turned off. By Default, SRAM Bank state set to ON.
Added condition checks to skip SRAM Bank state set logic for
Stoney platform.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
asic_type information is passed to ACP DMA Driver as platform data.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hard-coded compressed dailinks are not supported using
publicly-available firmwares, which creates unnecessary user
confusion [1]. Even if the firmware was available, the mainline
code does not have the required .dynamic=1 and .dpcm_playback=1
fields so probably never worked as is, and last and they conflict
with topology-defined streams.
Remove them and move on. This can be re-enabled with SOF later
in a more flexible manner.
[1] http://mailman.alsa-project.org/pipermail/alsa-devel/2017-August/124868.html
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For some reason the Atom/HiFi2 machine drivers use an id=1 instead
of zero as done on all other platforms. This gets in the way of
topology-based matching, realign for consistency. This should
not have any functional impact on existing solutions with don't rely
on topology.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove duplicate code with a common helper in all Intel machine drivers.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
get_codec_dai() is not used, remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same as for other codecs, enable MCLK by default. When it is not
present, e.g. on MinnowBoard B3 since it's not routed on the LSE
connector, we fall back to blck-based clocking.
The DMIC quirks are also fixed, there is a single DMIC input of the
codec.
reorder variables in reverse x-mas tree as suggested by Andy
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_pll function to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move set_sysclk to codec level and people can use it at both
codec and dai level.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Secondary DAI in Exynos I2S driver is not used by any of the currently
supported boards and it causes problems due to some limitations in the
ASoC code. Disable it until it gets proper support both by board-specific
and ASoC core code. Also disable IDMA support, which relies on secondary
DAI presence.
This patch fixes following kernel warning:
samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
------------[ cut here ]------------
WARNING: CPU: 3 PID: 82 at fs/proc/generic.c:330 proc_register+0xec/0x10c
proc_dir_entry 'sub0/prealloc' already registered
Modules linked in:
CPU: 3 PID: 82 Comm: kworker/3:1 Not tainted 4.14.0-rc5-next-20171017 #3089
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
[<c0110114>] (unwind_backtrace) from [<c010c900>] (show_stack+0x10/0x14)
[<c010c900>] (show_stack) from [<c083e664>] (dump_stack+0x90/0xc8)
[<c083e664>] (dump_stack) from [<c011d2b8>] (__warn+0xd4/0x100)
[<c011d2b8>] (__warn) from [<c011d384>] (warn_slowpath_fmt+0x38/0x48)
[<c011d384>] (warn_slowpath_fmt) from [<c0271268>] (proc_register+0xec/0x10c)
[<c0271268>] (proc_register) from [<c027130c>] (proc_create_data+0x84/0xc8)
[<c027130c>] (proc_create_data) from [<c061afbc>] (snd_info_register+0x64/0xcc)
[<c061afbc>] (snd_info_register) from [<c062a6e0>] (snd_pcm_lib_preallocate_pages1+0x78/0x1a0)
[<c062a6e0>] (snd_pcm_lib_preallocate_pages1) from [<c063eef4>] (dmaengine_pcm_new+0xa0/0x1ec)
[<c063eef4>] (dmaengine_pcm_new) from [<c062b9f8>] (snd_soc_platform_drv_pcm_new+0x1c/0x28)
[<c062b9f8>] (snd_soc_platform_drv_pcm_new) from [<c063d54c>] (soc_new_pcm+0x2f4/0x4f4)
[<c063d54c>] (soc_new_pcm) from [<c063107c>] (snd_soc_register_card+0xc4c/0xdc4)
[<c063107c>] (snd_soc_register_card) from [<c063db30>] (devm_snd_soc_register_card+0x34/0x70)
[<c063db30>] (devm_snd_soc_register_card) from [<c064af60>] (asoc_simple_card_probe+0x230/0x47c)
[<c064af60>] (asoc_simple_card_probe) from [<c047f8fc>] (platform_drv_probe+0x50/0xb0)
[<c047f8fc>] (platform_drv_probe) from [<c047dee0>] (driver_probe_device+0x2a0/0x46c)
[<c047dee0>] (driver_probe_device) from [<c047c0bc>] (bus_for_each_drv+0x44/0x8c)
[<c047c0bc>] (bus_for_each_drv) from [<c047db50>] (__device_attach+0xa0/0x134)
[<c047db50>] (__device_attach) from [<c047cf7c>] (bus_probe_device+0x88/0x90)
[<c047cf7c>] (bus_probe_device) from [<c047d484>] (deferred_probe_work_func+0x3c/0x168)
[<c047d484>] (deferred_probe_work_func) from [<c01371f8>] (process_one_work+0x188/0x41c)
[<c01371f8>] (process_one_work) from [<c01374b4>] (process_scheduled_works+0x28/0x38)
[<c01374b4>] (process_scheduled_works) from [<c01376d4>] (worker_thread+0x210/0x4dc)
[<c01376d4>] (worker_thread) from [<c013d9cc>] (kthread+0x128/0x164)
[<c013d9cc>] (kthread) from [<c0108848>] (ret_from_fork+0x14/0x2c)
---[ end trace bad8db6ee771d094 ]--
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the old AC97 is not used, CONFIG_SND_SOC_AC97_BUS is not
defined. As a consequence, in the error path, snd_soc_free_ac97_codec()
is not defined and triggers a compilation error.
Fix it for wm9705 and wm9712, as wm9713 is correctly written.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To make it consistent, add sentinel for sst_cnl_devdata also.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since FE dais can come from topology, add dai_load ops
for the dais from topology.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since FE dais can come from topology, split the FE dais from existing
dai array so that FE dais need not be registered if they come from
topology. Add use_tplg_pcm flag to check whether FE dais will be
registered from topology during dai driver component registration.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ADG inputs clock from CLK{A,B,C,I} and outputs clock from
CLKOUT{0,1,2,3} which is selected by BRG{A,B}.
Now, ADG is assuming BRGA is for 44100Hz related clocks,
BRGB is for 48000Hz related clocks.
Clock related debug is very difficult/confusable.
This patch cleanups clock related debug info.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Return proper error instead of 0 if the revision does not match.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current CTU/MIX/DVC are directly using rsnd_kctrl_cfg_m/s to control
val etc, but it is difficult to read/understand.
And there was no uniformity in access method.
This patch adds new rsnd_kctrl_xxx() and implements uniformed access
method.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The newly introduced function is declared as globally visible,
but is not declared in a header, causing a warning 'make W=1'
or 'make C=1':
sound/soc/soc-dapm.c:3782:1: warning: symbol 'snd_soc_dapm_free_kcontrol' was not declared. Should it be static?
The suggestion to make it static seems appropriate here, so let's
do that.
Fixes: 19ad683abc ("ASoC: dapm: Avoid creating kcontrol for params")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We now allocate the array conditionally, but we always pass
the pointer to the new snd_soc_dapm_free_kcontrol() function,
which introduces a warning for the case that it is not
initialized:
sound/soc/soc-dapm.c: In function 'snd_soc_dapm_new_pcm':
sound/soc/soc-dapm.c:3940:2: error: 'w_param_text' may be used uninitialized in this function [-Werror=maybe-uninitialized]
As snd_soc_dapm_free_kcontrol() is global, it doesn't get inlined
and gcc fails to notice that we don't actually access the array
in that case, so the code is actually safe. Adding an initialization
for the array pointer shuts up the warning.
Fixes: 19ad683abc ("ASoC: dapm: Avoid creating kcontrol for params")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
No need to print an error message if kzalloc fails.
The core will print it.
Reported-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC platform/codec will be replaced to component soon.
But, some function exist in "platform" doesn't exist in "component".
Current soc-core has snd_soc_register_component(), but
doesn't have snd_soc_add_component() like snd_soc_add_platform().
This patch adds it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set dma control ipc can be used to set the M/N divider, enable the clks. It
takes different payload for different configuration. So modify the
skl_dsp_set_dma_control API to take the size and node_id as argument.
Signed-off-by: Jaikrishna Nemallapudi <jaikrishnax.nemallapudi@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove dead code which was missed in previous changes. This is not
visible with git diff but there is a test+return on the same condition
just above.
Also reuse local variable instead of fetching the jack information twice.
Tested on Acer R11 (cyan)
Fixes: 3bbda5a386 ('ASoC: Intel: cht_bsw_max98090_ti: Fix jack initialization')
Cc: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Disable sys clock as well as ref clock when runtime suspended.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement suspend and resume callbacks to save and restore register
state, to support platforms where the power is disabled during suspend.
In future the driver could be converted to use regmap which would
simplify the suspend and resume code.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM to disable the clock when the device is not in use.
The ASoC core takes care of the pm_runtime_get_sync / put calls so we
just need to provide runtime_suspend / runtime_resume functions and
enable runtime PM.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement suspend and resume callbacks to save and restore register
state, to support platforms where the power is disabled during suspend.
In future the driver could be converted to use regmap which would
simplify the suspend and resume code.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Disable sys clock as well as ref clock when runtime suspended.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement suspend and resume callbacks to save and restore register
state, to support platforms where the power is disabled during suspend.
In future the driver could be converted to use regmap which would
simplify the suspend and resume code.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM to disable the clock when the device is not in use.
The ASoC core takes care of the pm_runtime_get_sync / put calls so we
just need to provide runtime_suspend / runtime_resume functions and
enable runtime PM.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Implement suspend and resume callbacks to save and restore register
state, to support platforms where the power is disabled during suspend.
In future the driver could be converted to use regmap which would
simplify the suspend and resume code.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check the the pm_runtime_get_sync return code and return if an error.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable active_slots is unsigned so checking whether it is less than
zero is not necessary.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently in codec to codec dai link if there are multiple
params defined then dapm can use created kcontrol to
decide which param to apply at runtime.
However, in case there is only single param configuration
then there is no point in creating the kcontrol and also there
is no point in allocating memory for kcontrol.
In the snd_soc_dapm_new_pcm function, there is memory
allocation happening for kcontrol which is later used
or not used based on num_param. It is better to not
allocate memory when there is only a single configuration.
This change is to remedy that anomaly.
Signed-off-by: anish kumar <yesanishhere@gmail.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the of_device_get_match_data() helper instead of open coding.
Note that when used with DT, there's always a valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
ALSA SoC platform/codec will be replaced to component soon.
This means 1 device might have multiple components. But current
unregister component function only checks "dev" to find it.
This means, unexpected component might be unregistered by current
function.
But, it is no problem if driver registered only 1 component.
To prepare avoid this issue, this patch adds new component
lookup function. it finds component by "dev" and "driver name".
Here, the reason why it uses "driver name" is that "component name"
was created by fmt_single_name() and difficult to use it from driver.
Driver of course knows its "driver name", thus, using it is more easy.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
These modes of operation were not working properly and it is
unclear if the hardware could fully support these modes properly.
There is little to be gained by enabling these modes, therefore,
we will just remove support.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPDIF port cannot modify its format so a set_fmt function is not
needed. Previously, we used a generic set_fmt for all ports and returned
an error code for the SPDIF port. It is cleaner to not populate the
set_fmt field.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The helper function cygnus_ssp_set_custom_fsync_width() is intended
to be called from an ASoC machine driver, need to export symbol
if using modules.
Signed-off-by: Lori Hikichi <lori.hikichi@broadcom.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Both DVC/MIX have Volume Ramp Control. This patch supprts MIX
Volume Ramp. One note is that main purpose of MIX Volume Ramp
is to reduce noise, thus, MIX Ramp range is very few if you
compare to DVC Volume Ramp (DVC = 5bit, MIX = 4bit).
You can use MIX Volume Ranp like below
amixer set "MIX Ramp Up Rate" "0.125 dB/1 step"
amixer set "MIX Ramp Down Rate" "0.125 dB/1 step"
amixer set "MIX Ramp" on
aplay xxx.wav &
amixer set "MIX",0 80% // DAI0 Volume Down
amixer set "MIX",1 100% // DAI1 Volume Up
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC is supporting Volume Ramp Rate, and MIX has Volume Ramp
but not yet supported. To support MIX Volume Ramp, we want to
share Rate List since DVC/MIX are using almost same list.
This patch move DVC specific Volume Ramp Rate List to core.c.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same CTU might be used few times if system/platform is using MIX.
For example below case.
DAI0 playback = <&src0 &ctu02 &mix0 &dvc0 &ssi0>;
DAI1 playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
This case, ALSA will have CTU,0 and CTU,1 kcontrol interfaces,
but these are same CTU. This is confusing.
This patch adds new flags and avoid such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Same DVC might be used few times if system/platform is using MIX.
For example below case.
DAI0 playback = <&src0 &ctu02 &mix0 &dvc0 &ssi0>;
DAI1 playback = <&src2 &ctu03 &mix0 &dvc0 &ssi0>;
This case, ALSA will have DVC,0 and DVC,1 kcontrol interfaces,
but these are same DVC. This is confusing.
This patch adds new flags and avoid such case.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSI is using rsnd_ssi_flags_xxx() macro to control flags.
But it is useful macro not only for SSI. This patch replace it
to more generic rsnd_flags_xxx().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The macro used to set the microphone bias level causes the
snd_soc_write() call to overwrite other fields in the CDC_A_MICB_1_VAL
register. The macro also does not return the proper level value
to use. This fixes this by preserving all bits from the register
that are not the level while setting the level.
Signed-off-by: Jean-François Têtu <jean-francois.tetu@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename suspend and resume functions to runtime_suspend and
runtime_resume, which is what they actually are. This will avoid
confusion when adding suspend and resume functions in a subsequent
patch.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add pm_runtime_get_sync and pm_runtime_put calls to set_fmt callback
function. This fixes a bus error during boot when CONFIG_SUSPEND is
defined when this function gets called while the device is runtime
disabled and device registers are accessed while the clock is disabled.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename suspend and resume functions to runtime_suspend and
runtime_resume, which is what they actually are. This will avoid
confusion when adding suspend and resume functions in a subsequent
patch.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the recent commit d9f9c167ed ("ASoC: rockchip: Init dapm routes
dynamically") we improperly allocated memory for the card->dapm_routes
causing us to overflow the allocation on every boot. Oops.
Let's allocate the correct amount of memory. We'll also add a check
to make sure that we don't overrun memory even if we encounter some
sort of weird device tree.
Fixes: d9f9c167ed ("ASoC: rockchip: Init dapm routes dynamically")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The very first time a headset is plugged in, detection is unreliable
because bias hasn't been configured yet, it's done once a mechanical
insertion interrupt has been triggered, so following insertions (and
thus detections) are not affected.
To fix the very first detection, the bias must also be configured in the
function that setup the MBHC. Move pm8916_wcd_setup_mbhc after
pm8916_mbhc_configure_bias to avoid a forward declaration.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current device tree representation of the R-Car SSI assumes that they
are numbered consecutively, starting from 0. Alas, this is not the case
with the R8A77995 (D3) SoC which SSI1/SSI2 aren't present. In order to
keep the existing device trees working, I'm suggesting to use a disabled
node for SSI0/SSI1. Teach the SSI probe to just skip disabled nodes.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo snd_soc_msm8916_analog | grep alias
$
After this patch:
$ modinfo snd_soc_msm8916_analog | grep alias
alias: of:N*T*Cqcom,pm8916-wcd-analog-codecC*
alias: of:N*T*Cqcom,pm8916-wcd-analog-codec
Signed-off-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
msm8916-wcd-analog uses button0 to differentiate between headphone and
headset. Under some circumstances, button pressed and released
interrupts are not fired as the driver expects it.
For instance, with some connectors, there are spurious button-pressed
interrupts when unplugging a headphone, without the corresponding
button-released interrupt. But the codec always alternates between
button pressed and released interrupts, it cannot fire two interrupts of
the same kind in a row. That means that when the headphone is plugged
back, only a button-released interrupt will be fired instead of pressed
then released. This causes the driver to report headphone as headset.
By changing the logic and relying on button 0 release interrupt, the
driver could be made more robust for connectors that differ from the one
used on the Dragonboard's audio mezzanine.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to set a specific bit for 50 bclk rate. So add set_bclk_ratio
function to set the bit.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jack name is not getting formatted correctly hence resulting
in invalid name for HDMI/DP input devices.
This was recently exposed due changes brought by MST:
commit 3a13347f05 ("ASoC: Intel: kbl: Add jack port initialize
in kbl machine drivers")
Signed-off-by: Chintan Patel <chintan.m.patel@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current ALSA SoC, Codec only has set_bias_level feature.
Codec will be merged into Component in next generation ALSA SoC,
thus current Codec specific feature need to be merged into it.
This is glue patch for it.
Codec driver has .idle_bias_off for dapm bias. But Component
driver doesn't have it, and dapm->idle_bias_off is set as "true".
To keep compatibility, this patch adds "idle_bias_on" instead of
".idle_bias_off" on Component driver.
dapm->idle_bias_off will be set by inverted idle_bias_on.
When we replace Codec to Component, the driver which has
".idle_bias_off = true" is just remove it,
and the driver which doesn't have it will have new
".idle_bias_on = true".
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In current ALSA SoC, Platform only has pcm_new/pcm_free feature,
but it should be supported on Component level. This patch adds it.
The v1 was added commit 99b04f4c40 ("ASoC: add Component level
pcm_new/pcm_free") but it called all "card" connected component's
pcm_new/free, it was wrong.
This patch calls "rtd" connected component.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When ASoC driver is unbound dynamically during its operation (i.e. a
kind of hot-unplug), we may hit Oops due to the resource access after
the release by a delayed work, something like:
Unable to handle kernel paging request at virtual address dead000000000220
....
PC is at soc_dapm_dai_stream_event.isra.14+0x20/0xd0
LR is at snd_soc_dapm_stream_event+0x74/0xa8
....
[<ffff000008715610>] soc_dapm_dai_stream_event.isra.14+0x20/0xd0
[<ffff00000871989c>] snd_soc_dapm_stream_event+0x74/0xa8
[<ffff00000871b23c>] close_delayed_work+0x3c/0x50
[<ffff0000080bbd6c>] process_one_work+0x1ac/0x318
[<ffff0000080bbf20>] worker_thread+0x48/0x420
[<ffff0000080c201c>] kthread+0xfc/0x128
[<ffff0000080842f0>] ret_from_fork+0x10/0x18
For fixing the race, this patch adds a sync-point in pcm private_free
callback to finish the delayed work before actually releasing the
resources.
Reported-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Reported-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
'Kbl Audio Headset Playback' FE DAI also needs SSP hw param fix.
Add this dai also to be handled in kabylake_ssp_fixup() call.
Signed-off-by: Harsha Priya <harshapriya.n@intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make kirkwood_soc_platform const as it only passed to a const argument
of the function snd_soc_register_platform in the file referencing it.
Make the declaration const too.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Double NULL pointer check for ops and ops->func is difficult to read
and might be forget to check it if new func was add.
This patch adds new null_snd_soc_ops and use it if rtd->dai_link didn't
have it to avoid NULL ops, and reduces ops NULL check.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The kcontrol for the third input (rxN_mix1_inp3) of both RX2
and RX3 mixers are not using the correct control register. This simple
patch fixes this.
Signed-off-by: Jean-François Têtu <jean-francois.tetu@savoirfairelinux.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make snd_soc_dapm_add_routes and snd_soc_dapm_del_routes use the
SND_SOC_DAPM_CLASS_RUNTIME dapm subclass to allow dynamic dapm route
updates.
Signed-off-by: Stuart Henderson <stuarth@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On soc_add_dai(), it uses null_dai_ops if driver doesn't have
its own ops. This means, dai->driver->ops never been NULL.
dai->driver->ops check is not needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
On soc_add_dai(), it is checking dai->driver->xxx,
This means, dai->driver is mandatory, never been NULL.
dai->driver check is not needed.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
static soc_free_pcm_runtime() is never called with rtd == NULL.
This patch removes unnecessary rtd == NULL check from
soc_free_pcm_runtime().
Furthermore, NULL check before kfree() is not needed.
This patch removes such ckeck too.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
For now reason the current card name is a ridiculous
'cherrytrailcraudio'. This isn't very useful or self-explanatory,
change to driver name cht-bsw-rt5672.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code scans all components looking for the default name
i2c-10EC5670:00, which of course doesn't work in platforms
where the BIOS uses a different HID such as Dell 5585
Since we already have the correct information available, just
use the actual codec name and length.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Additional checks exposed a mistake in the quirk for the Dell Venue
Pro 5855 (Dmic2 instead of Dmic1). Rather than adding quirk tables,
merge all quirks in a single table and use flags to differentiate
platforms. Also add a parameter override to help support additional
platforms using this codec
CC: Bard Liao <bardliao@realtek.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the irq handler "rt5663_irq", while the codec is not initialized,
rt5663->codec will be null, and it will cause the kernel panic in the debug
print enabled.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, wm8998 has two input mux controls on IN1 and attempts to
switch these together when the A position is configured to be in digital
mode. This is because the digital mode requires pins from both the L and
R channels. However, this doesn't work as intended because whilst the
registers on the chip are changed the corresponding DAPM
representation is only updated for the mux actually being changed by the
user. The DAPM graph being out of sync with the hardware can cause some
odd issues with incorrect things being powered etc.
To avoid this issue and simplify the code somewhat, simply let the user
set the muxes as they desire. If they set an invalid configuration they
might not get audio from the DMIC but most of the chip requires you to
set a valid audio route to get audio.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The call to slk_tplg_fill_res_tkn is passing dir and pin_index in the
wrong order, they need to be in pin_index, dir order to match the function
slk_tplg_fill_res_tkn correctly.
Detected by CoveritScan, CID#1454992 ("Arguments in wrong order")
Fixes: f6fa56e225 ("ASoC: Intel: Skylake: Parse and update module config structure")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
R-Car sound DMA will be used from SSI/SRC.
dma.c doesn't alloc DMA handler in .probe timing, because we don't
know what kind of DMA transfer will be used then.
Thus, SSI/SRC have *rsnd_mod for DMA. rsnd_dma_attach() will allocate
it and attach it to system.
It will be PIO mode if it can't alloc DMA handler.
In case of MIX is used, rsnd_dma_attach() will be called twice from SSI.
To avoid duplicate allocation, current rsnd_dma_attach() is checking
allocated DMA handler. This DMA related operation is a little bit
difficult to understand.
This patch adds new rsnd_dma_alloc() and separates allocation and attach
for readable code.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_kasprintf() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The output volume limits allow signals to be limited to specific levels
appropriate for the hardware attached. As this is a property of the
hardware itself these will be configured through device tree.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't use BUG_ON() for a non-critical sanity check on production
systems. This patch either removes useless BUG_ON() calls.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't use BUG_ON() for a non-critical sanity check on production
systems. This patch replaces with a softer WARN_ON() and an error
path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't use BUG_ON() for a non-critical sanity check on production
systems. This patch replaces with a softer WARN_ON() and an error
path.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
hw_params may be fixup by be_hw_params_fixup, calling
soc_pcm_params_symmetry() before hw_params will have issue
if there is hw_params changes in be_hw_params_fixup.
For example, with following use case
1. a dai-link which is able to convert sample rate on BE side
2. set BE playback and capture sample rate to 44100Hz
3. play a 48000Hz audio stream with this dai-link
4. record from this dai-link with 44100Hz sample rate
Got following error message when record starts
[ 495.013527] be_link_ak4613: ASoC: unmatched rate symmetry: 48000 - 44100
[ 495.021729] be_link_ak4613: ASoC: hw_params BE failed -22
[ 495.028589] rsnd_link0: ASoC: hw_params BE failed -22
Because in soc_pcm_hw_params(), FE rate is still having value before
it is fixup by be_hw_params_fixup(), when soc_pcm_params_symmetry() checks
symmetry, thus soc_pcm_params_symmetry() complains about the unmatched rate
between the active stream and the new stream tries to start.
This patch moves soc_pcm_params_symmetry() after hw_params to resolve the
above issue.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even though the tfa9879 driver can probe via device tree trough the
I2C core code, it is preferable to have explicit device tree
bindings instead [1], so add this support.
[1] https://www.spinics.net/lists/devicetree/msg195176.html
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
refactor snd_soc_dapm_new_pcm to reduce the size of
this function to facilitate further refactoring.
Signed-off-by: anish kumar <yesanishhere@gmail.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
w_param_text[count] is freed in the wrong error path.
Fix it by shifting the outfree_w_param label.
Signed-off-by: anish kumar <yesanishhere@gmail.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Don't populate the read-only arrays div and pd on the stack,
instead make them static const. Makes the object code smaller by 210 bytes:
Before:
text data bss dec hex filename
2869 720 0 3589 e05 sound/soc/codecs/rl6231.o
After:
text data bss dec hex filename
2495 880 0 3375 d2f sound/soc/codecs/rl6231.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a private data structure. This is a preparation for a codec which
would need an another data on top of snd_ac97, which will be the case
when an MFD wm97xx device will probe wm9705.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the new ac97 bus model, where devices are automatically
discovered on AC-Links.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
No file in sound/soc/intel/ use any miscdevice.
This patch remove this uncessary include.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get is called with GPIOF_OUT_INIT_LOW but the function doesn't
allow the parameters. Unluckily, GPIOF_OUT_INIT_LOW is same value as
GPIOD_ASIS and gpio direction isn't set properly.
Muted stream comes up when I try recording some sounds on TM2. mic-bias
gpiod state can't be changed because the gpiod is created with the invalid
parameter. The gpio should be set GPIOD_OUT_HIGH.
Fixes: 1bfbc260a5 ("ASoC: samsung: Add machine driver for Exynos5433 based TM2 board")
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add specific cpu_dai_name to dai_link because samsung i2s driver registers
two dais and components. Selecting one of them clearly is needed more
information like cpu_dai_name, of_node. The reason why the dai_links have
to use 'samsung-i2s' for cpu_dai is that 'samsung-i2s-sec' doesn't have a
capture functionality.
Without this code, cpu_dai will be selected the first one of the
component_list. For example, if I describe nothing to cpu_dai_name,
'samsung-i2s-sec' might be selected to HiFi Primay.
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add specific dais name when components are registered. Component and dai
name will follow their parent dev name, if the name isn't described. In
case of this driver, each dais will have same name like '11440000.i2s0' by
fmt_single_name function.
The problem having same name is that TM2 machine driver can't detect
capture devices correctly. Machine driver doesn't know which one is proper
to use for cpu dai. The driver just selects to use 'samsung-i2c-sec' that
doesn't have capture functionality because the component of
samsung-i2s-sec is located in the first of the component_list.
I add dai name like 'samsung-i2s', 'samsung-i2s-sec' for each dais. The
reason why adding dai id to 1 is that it doesn't allow to use particular
dai name in case of when I use 0 for dai id.
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently all the audio related device tree entries are handled by the
MFD code, for most parts of the Arizona driver we group the device
tree handling with the component that uses it and should do so here as
well.
Add handling in the ASoC code for the audio device tree entries, a
later patch removes the MFD side handling but there is no harm in it
being duplicated temporarily.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the driver has quite a few small initialisation functions, in
preparation for some refactoring add a new function arizona_init_common.
This will be used bus probe level initialisation that is common across
Arizona devices. For now just move the notifier chain initialisation in
there.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Jacks are created but only enabled when the external TI chip is
present, this probably never worked as well. Forklift the gpio-based
code from the legacy byt-max98090 driver, with however a less strict
error check. It's fine to let users enjoy their device even if
jack detection doesn't work - it almost never does without quirks...
Tested on Lenovo100s
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the ts3a227e audio accessory detection hardware is present and its
driver probed, the jack needs to be created before enabling jack
detection in the ts3a227e driver. With this patch, the jack is
instantiated in the max98090 headset init function if the ts3a227e is
present. This fixes a null pointer dereference as the jack detection
enabling function in the ts3a driver was called before the jack is
created.
[minor correction to keep error handling on jack creation the same
as before by Pierre Bossart]
Signed-off-by: Thierry Escande <thierry.escande@collabora.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Baytrail Chromebooks used to be managed with legacy driver which
is not compatible with atom/sst drivers. Reuse CHT driver to
handle max98098 codec and allow distributions to support all
Atom platforms with the same build.
The legacy byt-max98090 can still be used but in a build for
Baytrail+max98090 only.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-By: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
