Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+QE+
-----END PGP SIGNATURE-----
Merge tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Merge "Ux500 Device Tree changes for the v4.2 series" form Linus Walleij:
Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.
* tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: add the sensors to the STUIB board
ARM: ux500: assign the sensor trigger IRQs
ARM: ux500: fix lsm303dlh magnetometer compat string
ARM: ux500: add CoreSight blocks to DTS file
ARM: ux500: define CPU topology
The ST sensors on the Ux500 boards were not utilizing the IRQs
for data ready sample triggers. Enable this by assigning the
right GPIO lines and interrupt lines (when the GPIO lines are
used for IRQs) to the accelerometer, gyro and magnetometer
sensors.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The magnetometer found on the Ux500 TVK and Snowball boards
is a LSM303DLH not a LSM303DLM, small differences but still
different. Put in the right compatible strings and things start
working smoothly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO regulator for the SD-card isn't a ux500 SOC configuration, but
instead it's specific to the board. Move the definition of it, into the
board DTSs.
Fixes: c94a4ab7af ("ARM: ux500: Disable the MMCI gpio-regulator by default")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik pin controller and all associated device
trees to use the standard, generic config bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This converts the Nomadik pin controller and all associated device
trees to use the standard, generic mux bindings for pin controllers.
There are no such device trees deployed in the wild so this is
safe to do to set a good example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Analogous to commit 8858d88a25
that fixed commit 70b41abc15
"ARM: ux500: move MSP pin control to the device tree"
accidentally activated MSP2, giving rise to a boot scroll
scream as the kernel attempts to probe a driver for it and
fails to obtain DMA channel 14.
For some reason I forgot to fix this on the Snowball. Fix
this up by marking the node disabled again.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
This adds the STMicroelectonics MEMS sensor devices to the Ux500
family device trees:
- Accelerometer
- Magnetometer
- Gyroscope
- Pressure (barometer)
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Denis CIOCCA <denis.ciocca@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mmci host driver supports the common mmc DT parser, which enables
us to use the use common names instead.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Move the AB8500 muxing and biasing settings over from the board
file to the device tree, include it in the reference designs using
the AB8500: HREF prior to v60, v60plus and Snowball. Set up these
GPIO lines using hogs, just like in the board file.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To be able to enable SDR12|25 for SD-cards, we needed to fixup the
configuration in DT of the gpio regulator, which handles the signal
voltage level. Some configuration were missing and some were wrong.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the few remaining snowball pin configurations to the device
tree, reference these as hogs to the pin controller until there
are real devices that can make use of them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI0 block is not at all connected to the AB8500 on the
Snowball: it is connected to the external header. These pins
on the header may also be used for GPIO, but let's assume
that SPI is a probable usecase on the Snowball and mux in the
SPI block and use these for SPI.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This transfers the muxing and biasing of the ethernet-related
pins on the snowball over to the device tree.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.
We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Ux500 boards are layered like this:
ste-snowball.dts includes ste-href.dtsi that includes
ste-dbx500.dtsi.
The dbx500.dtsi defines the PRCMU SoC regulators so the SoC will
probe and you can use ampersand references where need be.
However the HREF common dtsi and these two boards redefine the
same PRCMU SoC regulators with the very same names and properties
for no reason. This is like filling in the same line three
times instead of drawing it once. Just delete the surplus
references and have the PRCMU regulators defines in the SoC
files ste-dbx500.dtsi, this is enough.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch set beginning with commit:
"ARM: ux500: Apply a ste-* prefix onto snowball.dts"
thru commit:
"ARM: ux500: Remove u9540.dts as it's been replaced"
altered the names of the ux500 device tree files but forgot
to:
- Rename the ccu8540-pinctrl.dtsi file
- Update #include statements from files using these
files, so the build broke.
- Update the Makefile for the device trees so the build
broke.
Fix it up so we can build them all again.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
