The wlcore state was checked without the mutex being taken. This leads
to WARN_ONs sometimes if a notification arrives when the driver
is on, but the mutex is only taken after it is off. This usually
happens if stopping the driver while connected to a network.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the sequence number of the broadcast AP link in the wlvif. For each
connected station, save the sequence number in the drv_priv part of
ieee80211_sta. Use the saved numbers on recovery/resume, with the
obligatory increment on recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Dont use free_sta() on AP global links. It would fail an internal check
within the function and various structures within the link struct would
not be reset.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Print board type, PG with metal and ROM versions.
This might help debugging HW related issues.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For STA we report beacon loss to higher levels so that wpa_s
can attempt to roam without disconnecting. In case of P2P CLI
we don't want to attempt roaming and instead disconnect immediately
upon beacon loss.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On !CONFIG_SMP builds spin_is_locked always returns 0. Assert the
locking using assert_spin_locked, which is written to behave correctly
in all cases.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
report the average beacon rssi which is calculated
by firmware for roaming statistics instead of the
last rx packet rssi. this results a more accurate
rssi reporting
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Accumulate the total number of sent packets per-link to find out how far
the encryption sequence number has progressed. Use this number as the
initial security sequence number after recovery.
This consolidates security sequence handling for both chip families, as
we no longer have to rely on 12xx specific Tx completion.
A fortunate side effect of this is correct management of seq numbers for
AP roles and multi-role scenarios.
When a link is removed we save the last seq number on a persistent part
of the wlvif. This helps the data survive through recoveries/suspends,
which also entail changes in the hlid of the link.
This functionality is STA only currently.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The HLID of a STA can change, particularly during recovery. Don't cache
the HLID before it was potentially allocated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit 144614f3eebd7d only allowed a single active link when
turning on the optimization, ignoring the fact that an AP has two
additional global links.
Use 3 links as an indication for a single active link. Use the
FW PSM bits to verify the extra active link belongs to the AP role.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Maximum number of supported RX BA sessions depends on chip type.
wl18xx supports 5 RX BA sessions while wl12xx supports 3.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is requiered to enter sleep mode with smaller delay in forced PS mode.
This fixes issue of testing force PS mode during VoIP traffic where packets
are sent every 20ms. Chip never enters ps mode with default 30 ms delay
in such test.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some devices can handle remain on channel requests differently
based on the request type/priority. Add support to
differentiate between different ROC types, i.e., indicate that
the ROC is required for sending managment frames.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Even in failed case of pm_runtime_get_sync, the usage_count
is incremented. In order to keep the usage_count with correct
value and runtime power management to behave correctly, call
pm_runtime_put(_sync) in such case.
Signed-off-by Liu Chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Li Fei <fei.li@intel.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pull networking update from David Miller:
1) Checkpoint/restarted TCP sockets now can properly propagate the TCP
timestamp offset. From Andrey Vagin.
2) VMWARE VM VSOCK layer, from Andy King.
3) Much improved support for virtual functions and SR-IOV in bnx2x,
from Ariel ELior.
4) All protocols on ipv4 and ipv6 are now network namespace aware, and
all the compatability checks for initial-namespace-only protocols is
removed. Thanks to Tom Parkin for helping deal with the last major
holdout, L2TP.
5) IPV6 support in netpoll and network namespace support in pktgen,
from Cong Wang.
6) Multiple Registration Protocol (MRP) and Multiple VLAN Registration
Protocol (MVRP) support, from David Ward.
7) Compute packet lengths more accurately in the packet scheduler, from
Eric Dumazet.
8) Use per-task page fragment allocator in skb_append_datato_frags(),
also from Eric Dumazet.
9) Add support for connection tracking labels in netfilter, from
Florian Westphal.
10) Fix default multicast group joining on ipv6, and add anti-spoofing
checks to 6to4 and 6rd. From Hannes Frederic Sowa.
11) Make ipv4/ipv6 fragmentation memory limits more reasonable in modern
times, rearrange inet frag datastructures for better cacheline
locality, and move more operations outside of locking. From Jesper
Dangaard Brouer.
12) Instead of strict master <--> slave relationships, allow arbitrary
scenerios with "upper device lists". From Jiri Pirko.
13) Improve rate limiting accuracy in TBF and act_police, also from Jiri
Pirko.
14) Add a BPF filter netfilter match target, from Willem de Bruijn.
15) Orphan and delete a bunch of pre-historic networking drivers from
Paul Gortmaker.
16) Add TSO support for GRE tunnels, from Pravin B SHelar. Although
this still needs some minor bug fixing before it's %100 correct in
all cases.
17) Handle unresolved IPSEC states like ARP, with a resolution packet
queue. From Steffen Klassert.
18) Remove TCP Appropriate Byte Count support (ABC), from Stephen
Hemminger. This was long overdue.
19) Support SO_REUSEPORT, from Tom Herbert.
20) Allow locking a socket BPF filter, so that it cannot change after a
process drops capabilities.
21) Add VLAN filtering to bridge, from Vlad Yasevich.
22) Bring ipv6 on-par with ipv4 and do not cache neighbour entries in
the ipv6 routes, from YOSHIFUJI Hideaki.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1538 commits)
ipv6: fix race condition regarding dst->expires and dst->from.
net: fix a wrong assignment in skb_split()
ip_gre: remove an extra dst_release()
ppp: set qdisc_tx_busylock to avoid LOCKDEP splat
atl1c: restore buffer state
net: fix a build failure when !CONFIG_PROC_FS
net: ipv4: fix waring -Wunused-variable
net: proc: fix build failed when procfs is not configured
Revert "xen: netback: remove redundant xenvif_put"
net: move procfs code to net/core/net-procfs.c
qmi_wwan, cdc-ether: add ADU960S
bonding: set sysfs device_type to 'bond'
bonding: fix bond_release_all inconsistencies
b44: use netdev_alloc_skb_ip_align()
xen: netback: remove redundant xenvif_put
net: fec: Do a sanity check on the gpio number
ip_gre: propogate target device GSO capability to the tunnel device
ip_gre: allow CSUM capable devices to handle packets
bonding: Fix initialize after use for 3ad machine state spinlock
bonding: Fix race condition between bond_enslave() and bond_3ad_update_lacp_rate()
...
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 0d2e7a5c (wireless: Remove unnecessary alloc/OOM messages,
alloc cleanups) OOM messages after alloc were removed from the wlcore
modules.
Commit afb43e6d (wlcore: remove if_ops from platform_data)
reintroduced a couple of those. This patch removes them.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are only a few drivers that use HW scan, and
all of those don't need a non-idle transition before
starting the scan -- some don't even care about idle
at all. Remove the flag and code associated with it.
The only driver that really actually needed this is
wl1251 and it can just do it itself in the hw_scan
callback -- implement that.
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In wl18xx, we use a new ACX command in order to set the remote
supported rates, once we know it (ie. after association). The wl12xx
firmware doesn't support changing the rates after the STA is started,
so we need to use all supported rates.
Commit 530abe19 (wlcore: add ACX_PEER_CAP command) broke that by using
wlvif->rate_set when starting the STA role.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add back-off settings to the wl18xx_mac_and_phy_params. We had an
empty space where the new parameters are added, so this change doesn't
affect backwards-compatibility with older firmwares.
Update WL18XX_CONF_VERSION accordingly.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There's no need to hide the actual error that was reported when
booting fails. For instance, on I/O error, we were returing
-EINVALID, which doesn't make sense at all.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The platform data is used not only by wlcore-based drivers, but also
by wl1251. Move it up in the directory hierarchy to reflect this.
Additionally, make it truly optional. At the moment, disabling
platform data while wl1251_sdio or wlcore_sdio are enabled doesn't
work, but it will be necessary when device tree support is
implemented.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The platform devices can be created by both wlcore_sdio and
wlcore_spi. Theoretically, if both are connected to the same board,
there will be a conflict.
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Just a small cleanup to use the pointer provided by wlcore_pdev_data
instead of using a separate pointer then copying.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We can't pass pointers from the platform data to the modules, because
with DT it cannot be done. Those pointers are not set by the board
files anyway. It's the bus modules that set them, so they can be
safely removed from the platform data without changing any board
files.
Create a new structure that the bus modules pass to wlcore. This
structure contains the if_ops pointers and a pointer to the actual
platform data.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
There is no platform-specific set_power method anymore. Power setting
is done in the bus modules (wlcore_sdio and wlcore_spi).
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
The PLT firmware used by wl12xx for calibration always has the same
version number as the single-role firmware.
Currntly the driver rejects the PLT firmware since anything that is
not single-role uses the multi-role version. Fix this by using the
single-role version for everything except multi-role.
Signed-off-by: Luciano Coelho <coelho@ti.com>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Remove now unused variables.
Remove unnecessary memset after kzalloc->kcalloc.
Whitespace cleanups for these changes.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Remove unnecessary pending tests from wl1251. Only compile tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Luciano Coelho <coelho@ti.com>
Cc: linux-wireless@vger.kernel.org
Some of the mmc drivers initiate DMA transfers with buffers passed from
higher layers. This means that the driver shouldn't ever pass non
DMA-able buffers, such as ones that are unaligned, allocated on the
stack or static.
Fix a couple of calls to the mmc layer in which buffers which weren't
necessarily DMA-able were passed.
[Use sizeof(*wl->buffer_32) instead of sizeof(u32) -- Luca]
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We have no idea how many VIFs there are requiring a special spare, we
know just about the number of keys set. Rename the counter appropriately
and toggle it whenever a special key is added/removed.
Previously this was only changed once, since it was toggled whenever
the actual spare was changed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
FW API changed and now PERIODIC_SCAN_REPORT_EVENT is sent
in case results were found at the end of each sched scan
cycle. Previous FW was missing that and broke sched scan.
This API change is available from 18xx FW 8.5.0.0.27
[Arik - move changes to 18xx specific files, align FW structures to
latest for scan command]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't use MIMO rates when HT mode is forced to SISO, even if we have
multiple antennas.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove the STA specific ba_rx_bitmap field and use the common links
structure. This simplifies code setting/checking the BA bitmap.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Protect all functions touching queue_stop_reasons by spin-lock, since
they are accessed by op_tx. Now there's no need to take the mutex
before caling wlcore_queue_xxx functions.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Start using the new hw_queue mechanism in mac80211 and give each AC in
each vif its own hw_queue number. This allows us to stop an AC in a vif
independently from other vifs.
Change the Tx watermark handling functions to count packets per AC in
vif. From now on fast links should not be able to hurt the throughput
of slow links on the same AC but on different vifs.
Change internal queue mgmt functions to operate per vif, to support the
new Tx watermark granularity. Make the global versions of the queue
stop/start functions to use the global mac80211 API for queue mgmt. This
helps in situations where the driver currently doesn't know all the vifs
that reside in mac80211. Recovery is a good example for such a case.
[Moved hw_base_queue addition into the wlcore_tx_get_mac80211_queue()
function; changed WARN_ONs to WARN_ON_ONCEs; simplified for loops;
fixed new checkpatch warnings. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Only allow a PSM STA to congest FW memory when it is the single active
link. Being a single STA doesn't imply a single link - there might be
other links on other roles.
[Changed WARN_ON to WARN_ON_ONCE -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Treat a single connected STA in PSM as a slow link and regulate Tx speed
according to slow link priority/stop thresholds.
This allows us to avoid flooding the FW, while delivering decent
throughput to a peer in forced-PSM.
[Small simplification of the if statements -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Update the 18xx FW status private part to include Tx related link
priorities. Introduce new HW ops to determine link priority per chip
family.
For 18xx the changes are:
- Suspended links are at most low priority and Tx for them is stopped
beyond the suspend threshold.
- Active links now get their thresholds directly from FW
- There's a new "stop" threshold for active links, at which point a link
stops receiving new packets.
Update the min 18xx FW version required to make sure suspended links
bitmap is advertised by the FW.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl->num_rx_desc was mistakenly initialized with WL18XX_NUM_TX_DESCRIPTORS
but it should use WL18XX_NUM_RX_DESCRIPTORS instead.
This bug was passed unnoticed because currently both RX and TX descriptors
are initialized to the same value (32).
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Even passive scans on DFS channels require us to send probe requests, so
configure the probe-req in this case.
Also use this opportunity to prevent the code from crashing in case no
SSIDs are sent from above. This will likely happen in the DFS case
introduced. Even a passive scan might need the probe request configured
because of DFS channels.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Treat Rx error code as a bitmask. This allows sending MIC failures
when other error bit are on.
Align Rx descriptor status mask to the FW definition.
Ease debugging in case FW reports failure to decrypt on packets.
Discard corrupted packets early in Rx path to avoid reporting other
abnormalities with corrupted packets that also have other failure bytes on.
Namely - we don't want to get a MIC failure on a corrupted packet.
This is mandated by the WiFi specification - see
section 11.4.2.4.1 in 802.11-2012.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There's a limit on scan dwell times of max 30ms in order
to avoid degrading voip traffic which could be going on
while scanning. However these dwell times increase the
chance of missing out on nearby APs leading to partial
scan results. Allow configuration of longer dwell times
in case there no active interface (i.e. no STA associated
or AP up).
[Arik - count started vifs using an in-driver function]
[Fixed some new checkpatch warnings regarding comments in the
networking subsystem. -- Luca]
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Require each incoming packet to have a valid vif. The injected Tx code
path was buggy (and unused), so disallow it altogether.
Cleanup a few places and add a warning so we can better discover
anomalies (corrupted skbs?) masquerading as injected Tx.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ACX_PEER_CAP command is just ACX_PEER_HT_CAP, but allows
configuring the peer's support rates as well.
this is needed because we start the station role when
the remote rates are not known yet.
the two commands should be unified in future fw versions,
but for now add a new set_peer_cap per-hw op, that will
use ACX_PEER_CAP for 18xx, and ACX_PEER_HT_CAP for 12xx.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Luciano Coelho <coelho@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obtain the last Tx rate from the FW status and translate it to
the mac80211 rate+flag format before sending it up via the Tx status.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Prioritize EDCA by choosing the AC before anything else. Use the
fast/slow link bitmap in FW to improve the scheduling algorithm for
the multi-link scenario.
Set packet thresholds to determine if a given link is high or low
priority according to its speed. A slow link will be given high priority
if the amount of packets queued for it in the FW is lower than the
slow-threshold. Similarly, a fast link will be given high priority if
the number of its packets queued in FW is smaller than the high-threshold.
The improved algorithm:
1. Choose optimal AC according to FW utilization
2. Traversing the VIFs in a round-robin fashion, try to choose a high
priority link. Links are traversed in a round-robin fashion inside a
VIF.
3. If no high priority links are found, choose the first non-empty
(low priority) link found in the round robin.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move FW-allocation tracking code to the fw_status function and track
allocations made by all links. These will be incorporated in the
improved Tx scheduling algorithm.
Manually zero the system link counters on op_stop, as this link is not
allocated the normal way.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This accounting will help find a vif that has data in a specific AC.
Otherwise we have to traverse all the links, which can be lengthy for
the AP case.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This allows us to pass only the link as a parameter to various functions
and deduce the wlvif. Note that this member will be NULL for global
links.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When a link is allocated, sometimes the "freed packets" counter in FW
is non zero, but we always assumed it is. This caused us to incorrectly
account FW allocated blocks in some cases.
When operating in AP mode, this bug caused some stations to never
come back from PSM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wlcore allocates two static structs wl1271_band_2ghz & wl1271_band_5ghz
which are used/modified by Reg-Domain e.g. some channel might be marked
as passive at some point. Make sure we don't keep stale settings around
if the HW is unregistered/registered during operation.
[Arik - use Tx-power constant and tweak commit message]
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make sure free_link is always called when removing an interface. This
ensures all skbs belonging to this interface are returned to mac80211.
Otherwise these dangling skbs might crash the system on the next
call to wl1271_tx_reset_link_queues(). This happens on recovery/stop or
an unsuccessful Tx flush.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Otherwise we risk contention for private members of our global structure
while op_stop_locked is running.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Sometimes the driver can perform a recovery while Tx is
active, this will trigger unnecessary warning which might
delay the recovery for more than 100 mS.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 18xx fw supports greenfield so add the
IEEE80211_HT_CAP_GRN_FLD flag to the supported
ht capabilities flags.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When removing an interface currently performing a ROC operation, clear
the current ROC state. This is useful especially during recovery and
keeps mac80211 in sync to our state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
all the current firmwares support elp, so
we can safely remove WLCORE_QUIRK_NO_ELP.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Under some circumstances, that fw might be asked to
remove a rx ba sessions it doesn't know about. In
this case, instead of triggering a recovery, accept
the error code (CMD_STATUS_NO_RX_BA_SESSION) and
ignore it.
[Arik - indicate failure up when the BA session cannot be setup]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Currently, each fw command/acx that return a status code
different than CMD_STATUS_SUCCESS will trigger a recovery
in the driver.
However, it is a valid for some fw commands to fail (e.g.
due to temporary lack of resources), so add new functions
that allow passing bitmap of valid error return values.
(make the current wl1271_cmd_send/wl1271_cmd_configure
wrappers around the new functions, in order to avoid
changing the whole driver)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
First set (low, medium and high TX power values) is used
for STA-HP background role. The 2nd set is used for other roles.
Update other mac/phy parameters according to new FW.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Conflicts:
drivers/net/wireless/ti/wl18xx/main.c
Update mac/phy paramters according to the default HP SISO boards.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 12xx FW doesn't support non-zero session ids for AP-mode. Introduce
an appropriate quirk to make sure the session id is always zero when
needed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For wl18xx, only the chip ID and the minor version number are
relevant. Ignore the other numbers which are either not used or
relate to internal projects or internal branches.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Previously we were only checking the single-role firmware version.
Now add code to check for the firmware versions separately for each
firmware type.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmware type and the project number fields in the firmware
version number, cannot be checked as if they increase sequentially,
because the former is the firmware type and the latter is an internal
project number. There's no guarantee that these numbers will remain
incremental, so use WLCORE_FW_VER_IGNORE.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The firmwares version string contain 5 integers. We used to consider
all the digits (except for the first one, which indicates the chip) as
linearly increasing version numbers. This is not correct, because
some of the integers indicate type of firmware (eg. single-role
vs. multi-role) or the internal project it was created for.
Besides, this varies a bit from chip to chip, so we need to make the
firmware version checks more flexible (eg. allow the lower driver to
ignore some of the integers). Additionally, we need to change the
code so that we only check for a linearly increasing number on the
fields where this actually makes sense.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We don't distinguish between STA and AP firmwares anymore, so the
firmware version checking and quirks setting in wl12xx isn't needed
anymore.
Remove implementation of .identify_fw in wl12xx and deprecated
definitions. Don't remove the op entirely from wlcore, because it may
be needed for more fine-grained checking later.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Move wl12xx-specific chip ID macros to the wl12xx driver and rename
them to 127X and 128X for clarity since both the "1" (2.4GHz) and the
"3" (2.4GHz and 5GHz) variants use the same chip ID.
Signed-off-by: Luciano Coelho <coelho@ti.com>
add support for recovery settings including bug_on_recovery and
no_recovery options.
These options can now be set using wl18xx-conf.bin file and wlconf
tool.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It's sometimes useful to gather information about the firmware
stability in long test runs, especially to see if problems are
recurring frequently or not. With this commit we count the number of
times a hardware recovery was issued and print it out during recovery
and in the driver_state in debugfs.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Adapt the new mac80211 BSS_CHANGED_PS notification,
and do the ps handling in mac80211's per-vif
callback (.bss_info_changed), rather than in
the per-device (.config) callback.
Make sure to configure it only after association.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
mask out CCK rates from the AP's local rates
when the interace is p2p interface (GO).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Try an opportunistic ROC when a STA is first added and stop the ROC when
the STA is removed or successfully authenticated. This would ensure we
don't miss auth/assoc/EAPOL packets during connection
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
18xx chips are capable of staying on 2 channels at the same time.
Introduce a chip-family specific parameter to set the number of channels
in the interface-combinations published by the driver.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Due to a bug, the fw asserts on fw log stop when dbg-pins are used.
Don't stop the fw log in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We support changing the channel BW when we started the STA role on
a 40Mhz bandwidth. Otherwise a reconnection is required.
Save the started channel width and use it when channel width updates
arrive.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Allow configuring different dwell times to the different
scan types (regular and scheduled).
Add new configuration entry (dwell_time_dfs) to
conf_scan_settings, in order to allow setting
different values for normal scan and scheduled scan.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
we have done updating the driver to the new fw
api, so make the driver operational again.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The interface might go down before we got the SCHED_STOPPED
event, so make sure to call ieee80211_sched_scan_stopped()
if the scanned interface is removed.
Replace sched_scanning with sched_vif in order to save
the scanned interface.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In 18xx the calibration process of the PHY Cortex domain
requires to perform an active calibration of the channel
before it can be used for transmission. To fulfill world
wide regulatory restrictions, fw should be always
synchronized/updated with current CRDA configuration.
Add a new "CMD_DFS_CHANNEL_CONFIG" command to update the
fw with current reg-domain, this command passes a bit map
of channels that are allowed to be used for transmission.
The driver shall update the fw during initialization and
after each change in the current reg-domain
configuration. The driver will save the channel number of
incoming beacons during the scan process, as they might
be a result of the passive scan on
"IEEE80211_CHAN_PASSIVE_SCAN" channel and will update the
fw accordingly once the scan is finished, the purpose of
this is to be ready in case of the authentication request
on one of these disabled (uncalibrated) channels.
The new command requires to wait for the fw completion
event "DFS_CHANNELS_CONFIG_COMPLETE_EVENT".
No scan commands (including the sched scan) can be
executed concurrently with the "CMD_DFS_CHANNEL_CONFIG",
wl->mutex ensures that.
[Arik - move reset of reg_ch_conf_last to safe place inside
op_stop_locked]
[Eliad - adjust to new event waiting api]
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
A new session_id is generated on link allocation.
it is saved in a global array and used later, on tx.
The new fw api adds new bcast/global_session_id
fields to start_role(ap) command, and a new session_id
field to add_peer command. align the driver with it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New fields were added to start_role(ap) and
set_peer_state commands, so the fw will be
able to know whether the sta/ap supports
wmm (the fw uses it in order to choose the
AC for some of its internally-generated frames)
For sta, take this value right from bss_conf->qos.
For ap, check for wmm support by looking for the
WMM IE in the configured beacon.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The event mailbox in wl18xx has a different
(non-compatible) structure.
Create common functions in wlcore to handle the
events, and call them from the chip-specific
event mailbox parsers.
This way, each driver (wl12xx/wl18xx) extracts
the event mailbox by itself according to its
own structure, and then calls the common
wlcore functions to handle it.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some fields were added to the channel_switch and
stop_channel_switch commands. Unfortunately,
the new 18xx channel_switch struct is not backward
compatible with the 12xx channel switch struct.
Add a new channel_switch op to wlcore, and update
the driver accordingly.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Some regdomains have more than 23 valid 5ghz channels,
so 18xx's MAX_CHANNELS_5GHZ was increased to 32.
Since now we have different max 5ghz channels values
for wl12xx and wl18xx, add a new wl->max_channels_5ghz
field, and use it for scan channels configuration.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The scan APIs of 12xx and 18xx are totally different.
Use some common functions as much as possible (e.g.
for setting scan channels), but split scan.c into
chip-specific scan.c files, each implementing its
own scan mechanism.
(in other words - move most of the current wlcore's
scan.c into wl12xx, and implement a similar mechanism
in 18xx, according to the new api)
New wlcore ops are introduced in order to call the
chip-specific scan functions.
The template indices used for each scan (regular/scheduled)
are also different between the chips, so set the correct
indices used for each scan type after identifying the chip.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new fw (8.5.0.0.28) is not backward compatible
with older drivers.
Use a new fw name (along with bumping the min
fw version), and add some code to fail
any boot attempt during the fw api alignment
patches (as the driver is not functional in
these transitional patches).
This code will be removed after the api alignment
will be done.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
18xx and 12xx have different scan APIs. In 18xx,
the scan and the sched scan use the same struct.
Prepare the scan configuration functions to it, by taking
more generic params (e.g. ieee80211_channel) instead of
specific structs/requests.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When we stop sched scan during connection, we shouldn't
call ieee80211_sched_scan_stopped directly, but do it
in the normal flow, as part of the SCHED_SCAN_COMPLETED
event handling.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove goto and label in the code where a simple if can be used. If
nothing else, this is at least confusing git diff, which shows the
label name as the name of the function.
Signed-off-by: Luciano Coelho <coelho@ti.com>
In multi-vif setup it's useful to know the role_id
being configured.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
With the new connection flow, start_sta is called before
the remote rates where updated. Use our own supported rates
instead to make sure we don't disable any potential rate
(the rate policies will be updated later, but there is
currently no way to update the remote rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Pass a variable indicating whether HT is enabled,
instead of duplicating the function call with
different arguments.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
When first configuring the rate policy, before auth,
we still don't have the correct rates that were
agreed during association.
Reconfigure the rate policy on association in order
to update them.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The supported_rates field should contain all our supported
rates, even if the remote peer doesn't support them.
(rename CONF_TX_AP_ENABLED_RATES to CONF_TX_ENABLED_RATES,
as we now use it for both ap and sta)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The default ps mode of the fw is auto, while the default
ps mode of mac80211 is active (ps off).
In order to sync them, configure active ps on association.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use the sta_state notifications to ROC when a station
is about to connect, and CROC respectively on
authorization (success) / deletion (failure).
Change the wl12xx_update_sta_state() flow to bail out
only on error, so multiple code blocks could refer
to the same state.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Add some basic chanctx implementation - debug prints,
and save the vif's channel/band/type.
After that, we no longer need to handle channel change
notifications on op_config.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We care only about the operational channel, not
about the temporal hw channel (which won't have
any real meaning in multi-channel env anyway)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
implement the reamin_on_channel() callback by starting
a dev role (already associated with the current vif)
on the requested channel/band.
This channel is usually different from the channel
of the sta role, so pass it to wl12xx_roc() as well,
and notify mac80211 (async) when the fw is ready
on the new channel.
Now, in case of offchannel tx, we should use the dev
role hlid, instead of the sta hlid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
for some reason, the wl12xx fw is not able to rx/tx
on the first start_sta cmd.
Workaround it by issuing a dummy start_sta + stop_sta
before starting the sta for the final time.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make the connection flow simpler by starting
sta role on bssid change.
Currently, we start dev role when going idle-off,
and start the sta role only after association
indication. This complicates the connection
flow with some possible intermediate states.
Make it simpler by starting sta role on bssid change,
which now happens *before* auth req get sent.
Update the handling of mac80211's notifications
and change wl1271_join/unjoin accordingly -
* Split wl1271_join() into wlcore_join (tuning on
a channel/bssid) and wlcore_set_assoc (configure
sta after association).
* Rename wl1271_unjoin() to wlcore_unset_assoc(), as
it is no longer the inversion of wl1271_join()
(now it's only used to disconnect associated sta /
joined ibss, without stopping the role).
* Set ssid before starting station role (needed for
start_role(sta)
While on it, split wl1271_bss_info_changed_sta() into
some sub-functions.
since we no longer use dev role in the connection flow,
we now always use the hlid of the sta role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.
This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to check whether unsigned variable is less than 0.
CC: Luciano Coelho <coelho@ti.com>
CC: linux-wireless@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The return value of wait_for_completion_timeout() is always
>= 0 with unsigned int type.
So the condition "ret < 0" or "ret >= 0" is pointless.
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
In corner case for wl12xx_spi_raw_write() when
len == SPI_AGGR_BUFFER_SIZE
we don't setup correctly spi transfer_list.
Next we will have garbage and strange errors
reported by SPI framework (eg. wrong speed_hz,
failed to transfer one message from queue)
when iterate transfer_list.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Luciano Coelho <coelho@ti.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
platform_device_unregister() only calls platform_device_del() and
platform_device_put(), thus use platform_device_unregister() to
simplify the code.
Also the documents in platform.c shows that platform_device_del
and platform_device_put must _only_ be externally called in error
cases. All other usage is a bug.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The function wl12xx_set_power_on is only called twice, once in
wl12xx_chip_wakeup and once in wl12xx_get_hw_info. On the failure of the
call in wl12xx_chip_wakeup, the containing function just returns, but on
the failure of the call in wl12xx_get_hw_info, the containing function
calls wl1271_power_off. This does not seem necessary, because if
wl12xx_set_power_on has set the power on and then fails, it has already
turned the power off.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r@
identifier f,free,a;
parameter list[n] ps;
type T;
expression e;
@@
f(ps,T a,...) {
... when any
when != a = e
if(...) { ... free(a); ... return ...; }
... when any
}
@@
identifier r.f,r.free;
expression x,a;
expression list[r.n] xs;
@@
* x = f(xs,a,...);
if (...) { ... free(a); ... return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Allow drivers to indicate their mactime is at RX completion and adjust
for this in mac80211. Also rename the existing RX_FLAG_MACTIME_MPDU to
RX_FLAG_MACTIME_START to clarify its intent. Based on similar code by
Johannes Berg.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[fix docs, atheros drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During hardware restart, all interfaces are iterated even
though they haven't been re-added to the driver, document
this behaviour. The same also happens during resume, which
is even more confusing since all of the interfaces were
previously removed from the driver. Make this optional so
drivers relying on the current behaviour can still use it,
but to let drivers that don't want this behaviour disable
it.
Also convert all API users, keeping the old semantics
except in hwsim, where the new normal ones are desired.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
wlcore_op_set_key() calls wl18xx_set_key(),
which in turn executes some of his function
calls without acquiring wl->mutex and making
sure the fw is awake.
Adding mutex_lock()/ps_elp_wakeup() calls is
not enough, as wl18xx_set_key() calls
wl1271_tx_flush() which can't be called while
the mutex is taken.
Add the required calls to wlcore_op_set_key,
but limit the queues_stop and flushing
to the only encryption types in which
a spare block might be needed (GEM and TKIP).
[Arik - move state != ON check]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The current elp timeout (the same as the dynamic
ps timeout - 1500ms) is too high. Usually,
wl1271_ps_elp_sleep() get called right after tx/rx,
which is fine, but some command might get sent
even when there is no traffic (e.g. ht changes
triggered by beacon frames), and leaving the
device awake for 1500ms in this case is redundant.
Use a timeout of 30ms.
The fw won't enter elp anyway before the dynamic-ps
timeout was expired as well (and it entered ps
successfully).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The NVS file is loaded by the device's probe callback with the help of
request_firmware(). Since request_firmware() relies on udevd, the
modules cannot be loaded before hotplug events are handled.
Fix this by loading the NVS file asynchronously and continue
initialization only after the firmware request is over.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Move most of the device-specific probe functionality into setup(), a new
op. By doing this, wlcore_probe will be the first to request a firmware
from userspace, making it easier to load the NVS file asynchronously.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When the no_recovery flag is used, the recovery work will not restart
the FW and the state will not be set to 'on'. To enable post-mortem
analysis, allow memory access in the 'restarting' state.
Also, since the FW might not be operational, don't fail the read/write
operations if elp_wakeup fails.
Reported-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Currently, all the (station) roles use the same
keep-alive template id (0). However, the klv
template ids shouldn't be shared by different
roles.
Implement a simple klv_templates bitmap, and let
each role allocate its own klv template id on
role initialization.
[Arik - remove invalidation of KLV template when getting into "idle".
This is already handled in unjoin]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Previously, invalidation of the keep-alive template was
done when going idle. However, while removing the
idle-handling we didn't move the keep-alive template
invalidation to another place.
This finally resulted in fw error when trying to use
the keep-alive template by another role.
(Note that we still have an error here - each role
should have its unique keep-alive template id, while
currently they all use CMD_TEMPL_KLV_IDX_NULL_DATA (0).
This only works now because we don't support concurrent
connected stations yet)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The driver used siso20 in this case for legacy reasons.
Reported-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The interrupt line is enabled by wl12xx_enable_interrupts and
wl18xx_enable_interrupts, but it will not be disabled in all failure
paths. Fix this.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
While recursive recovery is avoided during shutdown, a new recovery may
be queued when the FW boots. The recovery work will then try to stop an
already stopped hardware, which will most likely result in a kernel
panic.
Fix this by verifying that wl->state is on before queueing a new
recovery.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
add phy_fw_version_str to debugfs driver_state file.
information is taken during boot and stored in wl->chip.phy_fw_ver_str.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Limit SPI transmissions to the wl12xx max buffer size, as only 12xx was
tested with SPI.
This allows us to remove the global aggregation buffer constant.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Use number_of_assembled_ant5 phy param to indicate if A band is enabled:
if number_of_assembled_ant5 != 0 then it is enabled otherwise it is
disabled.
This aligns with phy implementation that uses this param both to indicate
if band is active and the number of antennas.
This parameter replaces enable_11a module param that was removed.
User-Space applications can use wlconf and/or INI files to disable A band
using this parameter.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This allows us to have a p2p-management interface (in STA mode),
as we as a group dedicated interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Enable device roles just before starting it.
This way, a single device role should be enough
for all vifs, as we can't use concurrent device
roles (which require ROC) anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
enabled (but not-started) sta role should be good enough
for scanning (both normal and scheduled), so use it
instead of the device_role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Make debug prints operational when dynamic debug is not defined.
This allows better debugging in production environments.
Change the driver prefix to "wlcore" while were at it.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Allow 3 native mac addresses on 18xx. On 12xx allow 2 native mac
addresses and set the LAA bit to create a third mac address. This
enabled operation with a separate group interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
mac80211's resume() callback might get called even if
the sta is not associated (but only up). The
resume sequence in this case results in configuring
the wake-up conditions of a non-started role, which
causes fw assertion.
Fix it by bailing out if the STA is not connected
(like we do on suspend()).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
wowlan filters should be configured in any case in suspend/resume.
This shouldn't be dependent on whether wakeup conditions are the
same for suspend and resume states. Only the FW command to
reconfigure wakeup conditions should be avoided in such a case.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Aggregation buffer size is set separately per 18xx/12xx chip family.
For 18xx aggragation buffer is set to 13 pages to utilize all
the available tx/rx descriptors for aggregation.
[Arik - remove redundant parts from the patch]
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Force Tx during the flush if there are packets pending in the driver.
This actually solves a bug where we would get called from the mac80211
wq context, which would prevent tx_work from getting queued, even when
the mutex is unlocked.
Don't stop the queues needlessly if there's nothing to flush. Use a
larger delay when sleeping to give the driver a chance to flush and
avoid cpu busy looping. Re-arrange the loop so the last iteration is
not wasted.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Print how much time a flush took. This will help debug the time it takes
to switch between channels.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
The IEEE80211_TX_CTL_NO_CCK_RATE flag is only set for mgmt packets
transmitted during p2p connection setup. Make sure to use the lowest
OFDM rate guarantee the peer always hears us.
Change the p2p rate policy to contain only the 6mpbs rate to acheive
this effect.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
This solves interoperability issues with peer that don't seem to "hear"
management packets transmitted in higher rates. Based on a previous
patch by Igal Chernobelsky.
Cc: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
recovery_work should be cancelled when stopping the device,
not when removing an interface (this is probably a leftover
from the single-role days)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When a function requests to recover, it would normally abort and will
not send any additional commands to the HW. However, other threads may
not be aware of the failure and could try to communicate with the HW
after a recovery was queued, but before the recovery work began.
Fix this by introducing an intermediate state which is set when recovery
is queued, and modify all state checks accordingly.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
When a single fw is being used for both single-role
and multi-role cases (e.g. 18xx), wl->mr_fw_name is
NULL, which results in NULL dereference while trying
to load the multi-role fw.
In this case, always use the single-role fw, and avoid
redundant fw switch by checking for this case in
wl12xx_need_fw_change() as well.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
default switch configuration set to pg2 chips (rdl 1/2/3/4).
removed hacks for specific board types.
pg1.x boards are now supported only using module params
or specific conf files.
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Declare any firmware that might be used by this driver.
If all drivers declare their firmware usage, then a sufficiently
complete list of firmware files can then be used to pare down
the external linux-firmware package to just the files in actual use.
Cc: Luciano Coelho <coelho@ti.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Use a module_platform_driver declaration instead of replicating the
init and exit functions in the driver.
Based on the patch for wl18xx by Devendra Naga.
Signed-off-by: Luciano Coelho <luca@coelho.fi>
the driver's init and exit routines can be implemented with the
module_platform_driver, as the init and exit code is same as
that of the module_platform_driver
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
Remove the control.sta pointer from ieee80211_tx_info to free up
sufficient space in the TX skb control buffer for the upcoming
Transmit Power Control (TPC).
Instead, the pointer is now on the stack in a new control struct
that is passed as a function parameter to the drivers' tx method.
Signed-off-by: Thomas Huehn <thomas@net.t-labs.tu-berlin.de>
Signed-off-by: Alina Friedrichsen <x-alina@gmx.net>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[reworded commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
avoid using the skb CB for getting the appropriate sta.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There was a bug hiding here since the hlid was sometimes inferred from
the sta, which might be invalid at this point.
Instead, propagate the hlid from the skb-queue where we got the skb
in the first place.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some rare cases, the CMD_ROC completion may take over 1 second.
The timeout had earlier been increased to 1000ms (from 750ms), but it
is still not enoug. Increase it to 1500ms.
Signed-off-by: Luciano Coelho <coelho@ti.com>
We need to wait for the command completion event when we send the
CMD_ROLE_STOP event otherwise we may try to send CMD_ROLE_START too
soon and get out-of-sync with the firmware.
In some cases, the firmware may not send the event, so we wait for the
event or for the timeout, whichever comes first.
This patch is based on an earlier version by Eliad.
Cc: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Use this opportunity to consolidate the check for MIMO support into a
separate function.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
handle errors of nla_put() inside the if(nla_put...) {}
This makes the code simpler and clearer because:
we take advantage from the fact that we have only one nla_put
in our routines (so no real need for goto label).
this avoids ugly goto forward followed by goto backward.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
this completes the calibrator based fem detect logic in driver:
driver starts (by calibrator) in plt_mode PLT_FEM_DETECT
wlcore inits and starts plt on wl12xx
wl12xx fetches fem number from firmware and stores it in wl->fem_manuf
wl12xx immediatly returns (doesn't start radio, etc...)
wlcore returns the fem_manuf to calibrator using WL1271_TM_ATTR_DATA
plt_mode is stopped
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
bip calibration is not required in wl18xx. Therefore we
disable also auto fem (using calibrator fem detect) mode.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
add wl->plt_mode that is used to indicate different plt
working modes: this will be used to implement calibrator side
auto fem detection where driver asks firmware to detect
the wlan fem radio type and returns it to calibrator.
this is not implemented yet and plt_modes: PLT_ON and
PLT_FEM_DETECT currently behave the same.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After the latest mac80211 changes, the sta has
the ap's sta pointer even before association.
This cause the auth and assoc frames to be sent
with the standard ap's rates, rather than the
basic rates.
Change the tx rate policy logic to use the regular
ap rates only for data packets (so control and mgmt
packets will be sent with basic rates)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
During interface removal, don't adjust sleep_auth if we are during
recovery. Since the FW is potentially dead we shouldn't talk to it.
Reported-by: Yossi Wortzel <yossiw@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Initialize val to 0, to remove the following warning with
CONFIG_CC_OPTIMIZE_FOR_SIZE. The compiler used was gcc 4.4.1
(Sourcery G++ Lite 2010q1-202).
drivers/net/wireless/ti/wl18xx/io.c: In function 'wl18xx_top_reg_read':
drivers/net/wireless/ti/wl18xx/io.c:57: warning: 'val' may be used uninitialized in this function
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Send EAPOLs using minimum basic rate for AP, STA, p2p GO and Client.
The patch fixes p2p connection issue with Realtek device in p2p
certification test 5.1.13 (DEVUT reinvokes Persistent Group).
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
ht_mode added to wl18xx conf struct in order to support different modes
from the configuration file, as well as module params, and by default
(working without a conf file and/or no module params).
the hack regarding conf.phy.low_band_component_type for each board
is now explicitly handled after parsing module params.
missing default values to wl18xx config added.
fix string module params not to have defaults (so if empty, param
can be taken from conf file).
update conf version to 3.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Ido Reis <idor@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
suspend and resume callbacks configure wakeup conditions to the FW
which may be different between suspend and resume.
This feature is currently not utilized as both in suspend and resume
FW wakeup every 1 DTIM. Avoid waking up the chip and doing the FW command
unless there's an actual difference in the wakeup conditions.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We get DMA alignment trouble if the beginning of the conf.phy struct is
not aligned to 4 bytes. Use kmemdup to ensure alignment.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We should free "chunk" here before returning the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't use the ht_mode module parameter for determining AP supported
rates. We can rely on channel type, since HT40 won't be enabled if our
HT cap doesn't support it.
Enable MIMO only if there enough antennas, and rely on per-peer rate
limitation to prevent IOPs.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
commit 587cc28 ("wlcore: compare ssid_len before comparing
ssids") introduced a new bug - the ssid length from the
request struct was compared against the ssid length of
another request, instead the one of the cmd.
This might cause the sched scan request to fail
(with -EINVAL) in many cases.
Signed-off-by: Eliad Peller <eliad@wizery.com>
It seems some parties have bad user experience when smaller values
are used. This should have little implications for power consumption,
since traffic is bursty in nature.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Avoid using the IEEE80211_NUM_BANDS constant for arrays sizes etc, as
this can contain bands unsupported by the driver (e.g. 60Ghz). Use an
internal constant to determine the number of bands.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
If some IO read/write fails while the FW is not loaded, a recovery
will not take place. This means the SDIO_FAILED flag will stay in place
forever and prevent further read/writes.
This can happen if a check for STATE_OFF was forgotten in some routine.
Take this opportunity to rename the flag to IO_FAILED, since we support
other buses as well.
Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
wlcore needs to wait for certain events for example
for roc complete event. Usually the events are received
from the FW very fast, therefore wlcore can poll with
a short delay and if after a second the event was
not received yet poll with a long (1-5 msec) delay.
This implementation is similar to the sending of
commands to the FW.
Empirically the change reduced the wait for roc event
from ~10-40msec to 100s of usecs.
[replace udelay/msleep with usleep_range - Arik]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
The interrupt line is disabled in op_stop using disable_irq. Since
pending interrupts are synchronized, the mutex has to be released before
disabling the interrupt to avoid a deadlock with the interrupt handler.
In addition, the internal state of the driver is only set to 'off'
after the interrupt is disabled. Otherwise, if an interrupt fires after
the state is set but before the interrupt line is disabled, the
interrupt handler will not be able to acknowledge the interrupt
resulting in an interrupt storm.
The driver's operations might be called during recovery. If these
acquire the mutex after it was released by op_stop, but before the
driver's state is changed, they may queue new work items instead of just
failing. This is especially problematic in the case of scans, in which a
new scan may be scheduled after all scan requests were cancelled.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
We have some API changes and new features in the new firmwares that
are not compatible with older drivers. Increase the version of the FW
filenames for wl12xx to 5.
Additionally, remove the duplicate definitions from wlcore_i.h and
remove the MODULE_FIRMWARE macro calls from the SDIO and SPI modules,
since they're irrelevant there.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The driver configures the firmware template for probe requests during
the scan process. If the same template is used for one-shot and sched
scans they will override each other when running scans simultaneously.
This fix works only on firmwares later than X.3.9.2.112 for single
role and X.3.9.2.23 for multi-role.
[Some cleaning-up and renaming of the quirk to something smaller --
Luca.]
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If recovery is called when the FW is off, we should clear the recovery
flag. Otherwise we risk booting the driver in permanent pending-recovery
state.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't read the FW panic log or print other debug data when recovery is
intended (i.e. FW type switch). This takes valuable time and can be
confusing to the user.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
This command is buggy (doesn't take the mutex) and unused. Instead, the
"start_recovery" file is used for the same purpose. Remove the code but
keep the command constant to avoid breaking the testmode ABI.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a Tx queue is currently stopped because of our Tx watermark flow
control, don't stop it again. This causes a warning to appear.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Refuse to boot if the FW version is too old. The minimum version is set
per chip, with the option of setting it per PG in the future.
When boot fails because of an old FW, display a helpful message.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New wl12xx firmware supports scheduled scans also while connected.
Stop blocking sched scan requests when connected and add a quirk to
block in hardware that don't support it (currently wl18xx doesn't).
This requires FW version 6/7.3.10.2.112 for single-role and
6/7.5.6.0.25 for multi-role.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Conflicts:
drivers/net/caif/caif_hsi.c
drivers/net/usb/qmi_wwan.c
The qmi_wwan merge was trivial.
The caif_hsi.c, on the other hand, was not. It's a conflict between
1c385f1fdf ("caif-hsi: Replace platform
device with ops structure.") in the net-next tree and commit
39abbaef19 ("caif-hsi: Postpone init of
HIS until open()") in the net tree.
I did my best with that one and will ask Sjur to check it out.
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM is disabled, no device can possibly
support WoWLAN since it can't go to sleep to start
with. Due to this, mac80211 had even rejected the
hardware registration. By making all the code and
data for WoWLAN depend on CONFIG_PM we can promote
this runtime error to a compile-time error.
Add #ifdef around all WoWLAN code to remove it in
systems that don't need it as they never suspend.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As recovery queuing can now occur from multiple code paths
it's convenient to know what triggered it in all cases
other than an intended recovery which is part of the
switch between single role to multi role.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Following the addition of propagating errors from the bus ops
there's a need to distinguish between bus errors (including timeout)
and a legitimate timeout occuring in cmd_wait_for_event_or_timeout.
In case of real bus errors we need to queue recovery even in cases
where a timeout on a response from the FW to a command is acceptable.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit 14bba17b "wl12xx: Propagate errors from wl1271_raw_write32"
breaks down TX in certain scenarios. wl1271_irq_locked() propagates
errors from wl1271_tx_work_locked however it may return -EBUSY
when the FW queues are full which is a legitimate case and not a
a real error. In this case a recovery is triggered by wl1271_irq
and this keeps repeating itself so TX is completely broken.
Fix it by avoiding propagating return values as errors even if they
aren't. Only bus (SDIO or SPI) ops failures would be progagated
as only these should trigger recovery.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We need to release the IRQ if hw_info() or identify_chip() fails. And
we need unregister the HW with mac80211 if there are any failures
after it's registered.
Signed-off-by: Luciano Coelho <coelho@ti.com>
The new PG2 version of the chip has a few differences in terms of FW
API if compared to PG1. PG1 is just a sample that shouldn't be used
in real life, so to avoid having to handle both separately, mark the
PG1 version as deprecated and bail out during probe.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Conflicts:
drivers/net/usb/qmi_wwan.c
net/batman-adv/translation-table.c
net/ipv6/route.c
qmi_wwan.c resolution provided by Bjørn Mork.
batman-adv conflict is dealing merely with the changes
of global function names to have a proper subsystem
prefix.
ipv6's route.c conflict is merely two side-by-side additions
of network namespace methods.
Signed-off-by: David S. Miller <davem@davemloft.net>
Mainline build reports:
warning: (WL12XX) selects WLCORE which has unmet direct dependencies (NETDEVICES && WLAN && WL_TI && GENERIC_HARDIRQS && MAC80211 && INET)
The INET dependency was added in commit
3c6af5b54f:
wl1271_main.c:(.text+0x271052): undefined reference to `unregister_inetaddr_
notifier'
wl1271_main.c:(.text+0x2714d7): undefined reference to `register_inetaddr_no
tifier'
Driver is doing some filtering based on IP addresses...
but this driver no longer has that code and it builds fine even when
CONFIG_INET is not enabled, so drop that dependency and eliminate the
kconfig warning message.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Cc: John W. Linville <linville@tuxdriver.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take the mutex early in the resume handler and use the locked version of
the IRQ routine. This ensures any recoveries queued will only take place
after resume has fully completed.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Separate the threaded IRQ handling routine into two functions.
The outer function takes the mutex and calls recovery on errors. It also
performs a Tx-path optimization to avoid redundant works.
The inner function is simplified - all calls to recovery are removed and
it assumes the lock is taken. The locked variant will be reused elsewhere.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Propagate some missing return values for Rx-filter related functions.
This and makes sure we always fail the suspend in case of SDIO errors.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If an error is detected after mac80211 is already suspended, the recovery
work will not be queued. This will leave the driver in a bad state on
resume.
Detect this in the resume op and re-queue a recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Set a flag and after the first read/write failure is encountered.
This flag will disallow further SDIO read/writes until op_stop() is
executed, which will clear all flags.
This prevents further errors from occurring, since one error usually
indicates that IO operations won't work anymore until the chip is
rebooted. By blocking more calls, we avoid extra timeouts and having
to wait for them to occur.
[Added second paragraph explaining why the change is needed. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We wish to postpone suspend if recovery is pending. This will make sure
the FW is in a good state and perform wowlan wakeup.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Applications running in the user space needs access to the
memory of the chip. Examples of such access
- read/write global variables
- access to firmware log
- dump memory after firmware panic event
Arbitrary 4-bytes aligned location can be accessed by
read/write file wlcore/mem
[Check return value of wlcore_raw_read/write and wlcore_set_partition
calls as required by the recent IO changes. -- Luca]
Signed-off-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
All io functions' return values should be propagated and handled. Add a
__must_check annotation to verify that the return values are checked and
to avoid future mistakes.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Propagate errors from wl1271_read_hwaddr. This function is only used
when reading the FW log (following a recovery), so don't read the FW log
in case of a bus error.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Propagate errors from wl1271_raw_write32 and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Propagate errors from wl1271_raw_read32. Since the read functions had no
way of returning errors in-band, change their prototypes.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Propagate errors from wl1271_write and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Propagate errors from wl1271_read and request for recovery when
appropriate.
Also rename prefixes of wlcore functions which their prototypes had to
be changed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wlcore_raw_read_data is called when the FW status is read which happens
while handling interrupts and when the FW log is read following a
recovery. Request a recovery in the former case, and don't read the FW
log in case the FW status read failed.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Make wl1271_raw_write and wl1271_raw_read return errors so the driver
could handle these appropriately.
Since the prototype has changed, also rename the prefix of these
functions to wlcore.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
While bus operations may fail, either due to HW or FW issues, these are
never propagated to higher layers. As a result, the core driver has no
way of knowing that the operations failed, and will only recover if high
level logic requires it (e.g. no command completion).
Change read/write bus operations to return errors to let higher layer
functionality handle these.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
In case a recovery is initiated, the FW can no longer be trusted, and
the driver should not handle any new FW events.
Disable the interrupt handler when a recovery is scheduled and balance
it back in the op_stop callback.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx_sdio_power_off() manually powers down the card regardless of the
runtime pm state. If wl12xx_sdio_power_on() is called before the card
was suspended by runtime PM, it will not power up the card.
As part of the HW detection, the chip's power is toggled. Since this
happens in the context of probing sdio, the power reference counter will
be higher than zero. As a result, when wl12xx_sdio_power_off() is
called, the chip will be powered down while still having a positive
power reference counter. If the interface is quickly activated, the
driver might try to transfer data to a powered off chip.
Fix this by ensuring that wl12xx_sdio_power_on() explicitly powers on
the chip in case runtime pm claims the chip is already powered on. To
avoid cases in which it is not possible to determine if the chip was
really powered on (card's power reference counter is positive), operate
on the mmc_card instead of the function.
Also verify that the chip is indeed powered on before powering off, to
avoid wrong reference counter values in error cases.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
After 934b9d1e (wl18xx: avoid some -Wformat warnings) there was still
a warning with (at least) ARM gcc version 4.4.1:
drivers/net/wireless/ti/wl18xx/main.c: In function 'wl18xx_conf_init':
drivers/net/wireless/ti/wl18xx/main.c:1026: warning: format '%ld' expects type 'long int', but argument 2 has type 'unsigned int'
Fix this by using %zu for the both formats, since the fw->size and the
macro (derived from sizeof()) are size_t.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Remove the cap IEEE80211_HT_CAP_DSSSCCK40 from the 5Ghz variant of
the siso40 HT capabilities. It is meaningless in 5Ghz.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Introduce a default set of HT capabilities that are set according to the
number of antennas on the board. Move the HT setting code down to allow
the number of antennas to be set (and optionally overridden) before it.
Remove the "mimo" HT option, since the default mode now enables MIMO is
possible.
Use this opportunity to add a helper function for setting HT
capabilities and reduce the volume of the code a bit.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The 18xx chip does not support MIMO in 5Ghz. Use the siso20 HT cap as
fallback in 5Ghz when "mimo" is requested.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
FW uses a few memory blocks as a buffer to accumulate FW logs before
transmitting them to the host over SDIO. When FW WatchDog recovery
occurs, the last FW traces are still pending in the buffer. Driver is
to read these FW traces whether log mode is continuous or on demand.
FW memory blocks allocated for the log buffer are handled as a link list:
the first 4 bytes in each memory block contain FW address to the next block.
The end of list condition depends on FW log mode:
- on demand: the list is cyclic, the next address is equal to the first address
- continuous: the address is equal to 0x2000000
Log data resides inside FW memory block with offset depending on
logger mode:
- on demand: 4 bytes (address of the next memory block)
- continuous: 4 bytes and Rx Descriptor structure size
Described FW logger API is backward compatible with previous FW versions.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The get survey op expects the low level driver to report
the noise level for a a given channel.
The noise calculated in wlcore is (rssi-snr/2), but since
the snr reported by the FW is a derivative from the rssi
this calculation is useless, and should not be reported
to the user space.
Reporting incorrect noise, results in the wpa_supplicant
miscalculating the roaming candidate priority, thus causing
a situation where an AP with a lower rssi level would be
chosen over a better AP.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Before patch b5d6d9b (wlcore/wl12xx/wl18xx: don't use TX align quirk
for wl127x), this was automatically set for all platforms. As this
should now be set explicitly, set it for PG2 as well.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
New PG2 firmwares have additional Rx descriptors.
Add a module parameter to manually set the number of Rx descriptors for
older versions (PG1). We cannot discriminate based on chip-id, since
this value must be set on probe.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The sleep_auth value of the last interface to be set up prevailed when
an interface was removed. Take care of this by correctly configuring the
value according to the remaining STA/AP interfaces.
Take this opportunity to refactor the sleep_auth setting code for better
readability.
[Small style fix. -- Luca]
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Hold a value for sta_sleep_auth that is amenable to change by debugfs.
When detecting a legal value in this variable on interface init, use it
as an override value for sleep_auth.
This makes debugging more intuitive using the debugfs value.
Increment the conf version since we added an element to the conf
structure.
Note: An AP going up will always set sleep_auth to PSM_CAM.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For FW debugging purposes, we may need to change the sleep mode
(aka. sleep_auth) by hand, and set it to the mode we want. To allow
this, a debugfs entry is added.
Now we store the sleep_auth value that has been set and use that
instead of the quirk to decide whether we should enter ELP or not.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
