Handle DRQ=1 ERR=1 situation. Revised according to what IDE try_to_flush_leftover_data() does.
Changes:
- For ATA PIO writes and ATAPI devices, just stop the HSM and let EH handle it.
- For ATA PIO reads, read only one block of junk data and then let EH handle it.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Merge ata_host_set_pio() and ata_host_set_dma() into ata_set_mode()
and use function-level *dev to iterate over devices. This eases
soon-to-follow ata_set_mode() interface change.
While at it, kill an unnecessary comment and normalize others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_set_mode() return without doing anything if there is no
device on the port. This is in preparation for ata_bus_probe()
changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch renames ata_dev_present() to ata_dev_enabled() and adds
ata_dev_disabled(). This is to discern the state where a device is
present but disabled from not-present state. This disctinction is
necessary when configuring transfer mode because device selection
timing must not be violated even if a device fails to configure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make do_probe_reset() generic by pushing classification check into
ata_drive_probe_reset() and rename it to ata_do_reset(). This will be
used by EH reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_spd_string() from sata_print_link_status(). This
will be used by SATA spd configuration routines.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_bus_probe() uses unsigned int rc to receive negative errno and
returns the converted unsigned int value. Convert temporary variables
to int and make ata_bus_probe() return negative errno on failure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_set_mode() return correct error value when ata_dev_set_mode()
fails.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The boot cmdline is parsed in parse_early_param() and
parse_args(,unknown_bootoption).
And __setup() is used in obsolete_checksetup().
start_kernel()
-> parse_args()
-> unknown_bootoption()
-> obsolete_checksetup()
If __setup()'s callback (->setup_func()) returns 1 in
obsolete_checksetup(), obsolete_checksetup() thinks a parameter was
handled.
If ->setup_func() returns 0, obsolete_checksetup() tries other
->setup_func(). If all ->setup_func() that matched a parameter returns 0,
a parameter is seted to argv_init[].
Then, when runing /sbin/init or init=app, argv_init[] is passed to the app.
If the app doesn't ignore those arguments, it will warning and exit.
This patch fixes a wrong usage of it, however fixes obvious one only.
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ata_xfer_tbl is terminated by entry with -1 as ->shift. However,
->shift was unsigned int making the termination condition bogus. This
patch converts ->shift and ->bits to int.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is no reason for the issuer to diddle with a failed qc as the
issuer has complete control over when a qc gets freed (usually in
->complete_fn). Make ata_qc_issue() responsible for completing qcs
which failed to issue.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On sg_err failure path, ata_qc_issue() doesn't mark the qc active
before returning. This triggers WARN_ON() in __ata_qc_complete() when
the qc gets completed. This patch moves ap->active_tag and
QCFLAG_ACTIVE setting to the top of the function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
MAP tables of ich6 and ich6m are wrong. Depending on port usage,
ata_piix may fail to initialize attached devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
print out information for ATAPI devices with CDB interrupts
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6: (24 commits)
[PARISC] Fix double free when removing HIL drivers
[PARISC] Add atomic_sub_and_test
[PARISC] Enabled some NLS modules in a500, b180 and c3000 defconfigs
[PARISC] Kill duplicated EXPORT_SYMBOL warnings
[PARISC] Move ioremap EXPORT_SYMBOL from parisc_ksyms.c
[PARISC] Make local_t use atomic_long_t
[PARISC] Update defconfigs
[PARISC] Add PREEMPT support
[PARISC] More useful readwrite lock helpers
[PARISC] Convert HIL drivers to use input_allocate_device
[PARISC] Fixup CONFIG_EISA a bit
[PARISC] getsockopt should be ENTRY_COMP
[PARISC] Remove obsolete CONFIG_DEBUG_IOREMAP
[PARISC] Temporary FIXME for ioremapping EISA regions
[PARISC] Enable ioremap functionality unconditionally
[PARISC] Fix stifb with IOREMAP and a 64-bit kernel
[PARISC] Add CONFIG_HPPA_IOREMAP to conditionally enable ioremap
[PARISC] Add STRICT_MM_TYPECHECKS
[PARISC] Fix IOREMAP with a 64-bit kernel
[PARISC] Add parisc implementation of flush_kernel_dcache_page()
...
Addresses in F-space must be accessed uncached on most parisc machines.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
(1) A DMA transfer size of 0x10000 was not being written
as 0x0000 in the PRDs. Fixed.
(1) The DEV_IRQ interrupt cause bit happens spuriously
during EDMA operation, and was not being ignored by the driver.
This led to various "drive busy" errors being reported,
with associated unpredictable behaviour. Fixed.
(2) If a SATA or PCI interrupt was received with no outstanding
command, the interrupt handler still attempted to invoke
ata_qc_complete(), triggering assert()/BUG_ON() behaviour
elsewhere in libata. Fixed.
The driver still has issues with confusion after error-recovery,
but should now be reliable in the absence of drive errors.
I will be looking more into the error-handling bugs next.
Signed-Off-By: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_dev_init_params() fixes:
- Get the "heads" and "sectors" parameters from caller instead of implicitly from dev->id[].
- Return AC_ERR_INVALID instead of 0 if an invalid parameter is found
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Last of the set, just clean up some oddments. Assuming the whole set is
now ok then the remaining differences are the setup of PIO_0 at reset
and the ->data_xfer method.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core
This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.
Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I think this is still needed with the new probe code (which btw seems to
be missing docs in upstream ?).
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is the minimal patch set to enable the current code to be used with
a controller following SFF (ie any PATA and early SATA controllers)
safely without crashes if there is no BMDMA area or if BMDMA is not
assigned by the BIOS for some reason.
Simplex status is recorded but not acted upon in this change, this isn't
a problem with the current drivers as none of them are for simplex
hardware. A following diff will deal with that.
The flags in the probe structure remain ->host_set_flags although Jeff
asked me to rename them, simply because the rename would break the usual
Linux rules that old code should break when there are changes. not
compile and run and then blow up/eat your computer/etc. Renaming this
later is a trivial exercise once a better name is chosen.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some CD-ROM drives are slow to clear DRQ, after the last data block
is read by PIO. Use ata_wait_idle() after reading the last data block.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Current irq-pio checks ERR bit and stops on ERR before it does anything else.
This behavior doesn't look right.
The DRQ bit should take higher precedence than the ERR bit.
Changes:
- Let the HSM do the data transfer whenever the
device asks for DRQ bit, even if the ERR bit is set.
- For DRQ=1 ERR=1, don't trust the data
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the the in_wq check easier to read as an inline function.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_check_atapi_dma() fix for LLDDs with the ATA_FLAG_PIO_POLLING flag.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cleanup the following unused functions:
- ata_pio_poll()
- ata_pio_complete()
- ata_pio_first_block()
- ata_pio_block()
- ata_pio_error()
ap->pio_task_timeout and other enums.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert ata_pio_task() to use the new ata_hsm_move().
Changes:
- refactor ata_pio_task() to poll device status register and
- call the new ata_hsm_move() when device indicates it is not BSY.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Let ata_hsm_move() work with both irq-pio and polling pio codepath.
Changes:
- add a new parameter "in_wq" for polling pio
- add return value "poll_next" to tell polling pio task whether the HSM is finished
- merge code from ata_pio_first_block() to the HSM_ST_FIRST state.
- call ata_poll_qc_complete() if called from the workqueue
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Minor fix for ata_hsm_move() to work with ata_host_intr().
Changes:
- WARN_ON() and comment fix
- Make the HSM_ST_LAST device status checking more rigid.
- Treat unknown HSM state as BUG().
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move out the irq-pio HSM code from ata_host_intr() to the new ata_hsm_move() function verbatim.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
atapi_packet_task() was replaced by ata_pio_task().
Remove the unused atapi_packet_task().
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix merge problem with upstream.
Changes:
1. add missing dev->cdb_len = 16 for ATA devices
2. use ata_pio_task instead of atapi_packet_task
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all occurences of 0xff.. in calls to function pci_set_dma_mask()
and pci_set_consistant_dma_mask() with the corresponding DMA_xBIT_MASK from
linux/dma-mapping.h.
Signed-off-by: Matthias Gehre <M.Gehre@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They deal with wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes statically assigned platform numbers and reworks the
powerpc platform probe code to use a better mechanism. With this,
board support files can simply declare a new machine type with a
macro, and implement a probe() function that uses the flattened
device-tree to detect if they apply for a given machine.
We now have a machine_is() macro that replaces the comparisons of
_machine with the various PLATFORM_* constants. This commit also
changes various drivers to use the new macro instead of looking at
_machine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
