Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc points out that when CONFIG_GPIOLIB is disabled,
gpiod_get_array_value_cansleep() returns 0 but fails to set its output:
drivers/phy/motorola/phy-mapphone-mdm6600.c: In function 'phy_mdm6600_status':
drivers/phy/motorola/phy-mapphone-mdm6600.c:220:24: error: 'values[0]' is used uninitialized in this function [-Werror=uninitialized]
This could be fixed more generally in gpiolib by returning a failure
code, but for this specific case, the easier workaround is to add a
gpiolib dependency.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
I noticed that phy_pm_runtime_get_sync() and phy_pm_runtime_put() are not
currently doing anything for phy-mapphone-mdm6600, only the sysfs interface
for works for "auto" and "on".
This is because of the shared GPIO pins between mdm6600 USB port and n_gsm
port. We have not enabled runtime PM for the phy driver until after we've
booted up mdm6600 properly to the USB mode. Otherwise phy_create() would
have called pm_runtime_enable() and pm_runtime_no_callbacks() automatically
on init.
Let's fix this by registering the phy a bit later after we've powered up
the mdm6600 USB port.
And as the PM runtime support is only needed for the n_gsm mode and not for
USB, we can allow the device to idle between phy_mdm6600_power_on() and
phy_mdm6600_power_off(). Note that for suspend, runtime_pm is already
disabled for the phy so we need to check for pm_runtime_enabled().
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In order to make use of array info obtained from gpiod_get_array() and
speed up processing of arrays matching single GPIO chip layout, that
information must be passed to get/set array functions. Extend the
functions' API with that additional parameter and update all users.
Pass NULL if a user builds an array itself from single GPIOs.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most users of get/set array functions iterate consecutive bits of data,
usually a single integer, while processing array of results obtained
from, or building an array of values to be passed to those functions.
Save time wasted on those iterations by changing the functions' API to
accept bitmaps.
All current users are updated as well.
More benefits from the change are expected as soon as planned support
for accepting/passing those bitmaps directly from/to respective GPIO
chip callbacks if applicable is implemented.
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Rojhalat Ibrahim <imr@rtschenk.de>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kbuilt test robot reported:
drivers/phy/motorola/phy-mapphone-mdm6600.c:188:16: warning: is used
uninitialized in this function [-Wuninitialized]
val |= values[i] << i;
~~~~~~^~~
Looking at the phy_mdm6600_status() values does get initialized by
gpiod_get_array_value_cansleep(), but we are using wrong enum
in that function. Let's fix the use, both end up being three though
so urgent rush on this one AFAIK.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for
MDM6600 on Droid 4")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
We can suspend the mdm6600 over USB via sysfs and then mdm6600 enters
a low-power idle mode. In the low-power mode, mdm6600 radio and n_gsm
uart are functional but we need to use USB mode0 GPIO pin to send a
wake-up pulse to the modem to talk with it over n_gsm.
As the GPIO mode0 line is dual purposed and and also needed by the
USB PHY driver to boot mdm6600 into the correct USB mode, let's also
manage the wake-up GPIO in the USB PHY driver. For the USB PHY idle,
there does not anything specific we need to do for runtime PM after
getting the PHY configured. The PHY framework already idles the USB
PHY when not in use separately from the mdm6600 state.
It seems that it takes about 100 - 200ms for mdm6600 to wake up from
the low-power idle mode. And then mdm6600 stays awake about 1.2s until
it needs to be kicked again. The mdm6600 status GPIO pins don't seem
to change state when mdm6600 changes between normal and idle mode.
Let's manage the mdm6600 mode with runtime PM. If phy-mapphone-mdm6600
sysfs entry for power/control is set to "on", we keep mdm6600 out of
idle by kicking the GPIO line. If the entry is set to "auto" we let
mdm6600 enter low-power state.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Let's add support for the GPIO controlled USB PHY on the MDM6600 modem.
It is used on some Motorola Mapphone series of phones and tablets such
as Droid 4.
The MDM6600 is hardwired to the first OHCI port in the Droid 4 case, and
is controlled by several GPIOs. The USB PHY is integrated into the MDM6600
device it seems. We know this as we get L3 errors from omap-usb-host if
trying to use the PHY before MDM6600 is configured.
The GPIOs controlling MDM6600 are used to power device on and off, to
configure the USB start-up mode (normal mode versus USB flashing), and
they also tell the state of the MDM6600 device.
The two start-up mode GPIOs are dual-purposed and used for out of band
(OOB) wake-up for USB and TS 27.010 serial mux. But we need to configure
the USB start-up mode first to get MDM6600 booted in the right mode to
be usable in the first place.
Note that the Motorola Mapphone Linux kernel tree has a "radio-ctrl"
driver for modems. But it really does not control the radio at all, it
just controls the modem power and start-up mode for USB. So I came to
the conclusion that we're better off having this done in the USB PHY
driver. For adding support for USB flashing mode, we can later on add
a kernel module option for flash_mode=1 or something similar.
Also note that currently there is no PM runtime support for the OHCI
on omap variant SoCs. So for low(er) power idle states, currenty both
ohci-platform and phy-mapphone-mdm6600 must be unloaded or unbound.
For reference here is what I measured for total power consumption on
an idle Droid 4 with and without USB related MDM6600 modules:
idle lcd off phy-mapphone-mdm6600 ohci-platform
153mW 284mW 344mW
So it seems that MDM6600 is currently not yet idling even with it's
radio turned off, but that's something that is beyond the control of
this USB PHY driver. This patch does get us to the point where modem
data and GPS are usable with libqmi and ModemManager for example.
Voice calls need more audio driver work.
Cc: devicetree@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The platform_get_irq_byname() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq_byname() error
checking for zero is not correct.
Fixes: 6d6ce40f63 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This line was indented further that it should have been.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Commit 8ae904e3c236 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
is missing return statement as noted by Colin Ian King
<colin.king@canonical.com>. If the optional pins are not configured,
we just want to return early and not attempt to configure the pins.
Fixes: 8ae904e3c236 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When MUSB is a loadable module, we get a link error for a built-in
CPCAP driver:
drivers/phy/built-in.o: In function `cpcap_usb_phy_remove':
phy-cpcap-usb.c:(.text+0xed9): undefined reference to `musb_mailbox'
This adds a Kconfig dependency to prevent this broken configuration,
enforcing that CPCAP can only be a module when MUSB is also a module.
Fixes: 68a1f7c9d470 ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some Motorola phones like droid 4 use a custom CPCAP PMIC that has a
multiplexing USB PHY.
This USB PHY can operate at least in four modes using pin multiplexing
and two control GPIOS:
- Pass through companion PHY for the SoC USB PHY
- ULPI PHY for the SoC
- Pass through USB for the modem
- UART debug console for the SoC
This patch adds support for droid 4 USB PHY and debug UART modes,
support for other modes can be added later on as needed.
Both peripheral and host mode are working for the USB. The
host mode depends on the cpcap-charger driver for VBUS.
VBUS and ID pin detection are done using cpcap-adc IIO ADC
driver.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
