For SPI NOR flash that are larger than 128Mbit (16MiB), we need 4 bytes
of address space to reach the entire flash; however, the original SPI
flash protocol used only 3 bytes for the address. So far, the practice
for handling this has been either to use new command opcodes that are
defined to use 4 bytes for their address, or to use special
mode-switching command to configure all traditionally-3-byte-address
commands to take 4 bytes instead.
Macronix and Spansion developed two incompatible methods for
entering/exiting "4-byte address mode." Micron flash uses the Macronix
method (OPCODE_{EN4B,EX4B}), not the Spansion method.
This patch solves addressing issues on Micron n25q256a and provides the
ability to support other future Micron SPI flash >16MiB.
Quoting a Micron representative:
"Majority of our NOR that needs 4-byte addressing (256Mb or 32MB and
higher) enter and exit 4byte through B7h and E9h commands. The
N25Q256A7xxx and N25Q512A7xxx parts do not support 4-byte addressing
mode via B7h or E9h command."
They further clarified that those that don't support the enter/exit
opcodes (B7h/E9h) are manufactured specifically to come up by default in
4-byte mode. We don't need to treat those parts any diffently, as they
will discard the EN4B opcode as a no-op.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
First, the function argument is 'offset' not 'column'.
Second, the 'data_buf' name is inconsistent with the rest of this file.
Just use 'buf'.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Gupta, Pekon <pekon@ti.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In order to make the nand_scan() work, the current code uses the hack code
to init the @nand_chip->ecc.size and the @nand_chip->ecc.strength. and
re-init some the ECC info in the gpmi_pre_bbt_scan().
This code is really a little ugly.
The patch does following changes:
(1) Use the nand_scan_ident()/nand_scan_tail() to replace the nand_scan().
(2) Init all the necessary values in the gpmi_init_last()
before we call the nand_scan_tail().
(3) remove the code setting the ECC info, let the mtd layer to do the
real job.
(4) remove the gpmi_scan_bbt(). we do not need this function any more.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We may do some ONFI get/set features operations before we call the
nand_scan_tail().
So move the default ONFI nand hooks into nand_set_defaults().
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Set the ecc step size for master/slave mtd_info{}.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add a new sys node to show the ecc step size.
The application then can uses this node to get the ecc step
size.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There are static checkers which complain when we declare variables as
64 bit bitfields but only use the lower 32 bits because of shift
wrapping. In this case "len" is declared as u64 as opposed to unsigned
long or something which might be 32 bits.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The create_freezable_workqueue() returns a NULL on error, it doesn't
return an ERR_PTR.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All callers of mtdtest_write() print the same error message on failure.
This incorporates the error message to mtdtest_write() and removes them
from the callers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
All callers of mtdtest_read() print the same error message on failure.
This incorporates the error message to mtdtest_read() and removes them
from the callers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The Armada 370 and Armada XP SoC families, selected by PLAT_ORION,
have a Nand Flash Controller (NFC) IP very similar to the one present
in PXA platforms. Therefore, we want to build this driver on PLAT_ORION.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When use_dma=0 there's no point in requesting resources for dma,
since they won't be used anyway. Therefore we remove that requirement,
therefore allowing devices without dma to pass the driver probe.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Now that we have added ARCH_HAS_DMA conditional the function
enable_int() may be unused. Declare it as __maybe_unused,
in order to remove the following warning, when the function is not used:
drivers/mtd/nand//pxa3xx_nand.c:343:24: warning: 'enable_int' defined
but not used [-Wunused-function]
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds a macro ARCH_HAS_DMA to compile-out arch specific
dma code, namely pxa_request_dma() and pxa_free_dma(). These symbols
are available only in pxa, which makes impossible to build the driver in
other platforms than ARCH_PXA.
In order to handle non-dma capable platforms, we implement a fallbacks that
allocate buffers as if 'use_dma=false', putting the dma related code
under the ARCH_HAS_DMA conditional.
Please note that the correct way to handle this is to migrate the
dma code to use of the mmp_pdma dmaengine driver. However, currently
this is not possible because the two dmaengine drivers can't work together.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This registers are not per-chip (aka host) but controller-wide,
so it's better to store them in the global 'info' structure.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the defined macros for NAND command instead of using a constant
internal structure. This commit is only a cleanup, there's no
functionality modification.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
There's no advantage in using a hardcoded name for the mtd device.
Instead use the provided by the platform_device.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is just a cosmetic change, to make the code more readable.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ONFI command 'parameter page read' needs a non-standard length.
Therefore, we enable the 'length override' field in NDCB0 and set
a non-zero 'length count' in NDCB3.
Additionally, the 'spare enable' bit must be disabled for any command
that sets a non-zero 'length count' in NDCB3.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some newer controllers support a fourth command buffer. This additional
command buffer allows to set an arbitrary length count, using the
NDCB3.NDLENCNT field, to perform non-standard length operations
such as the ONFI parameter page read.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some commands (such as the ONFI parameter page read) need to
clear the 'spare enable' bit. This commit allows to set/clear
depending on the prepared command, instead of having it always
set.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When ECC is not selected, the ECC enable bit must be cleared
in the NAND control register. Same applies to DMA.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This driver supports NFCv1 (as found in PXA SoC) and NFCv2 (as found in
Armada 370/XP SoC). As both controller has a few differences, a way of
distinguishing between the two is needed.
This commit introduces a new compatible string 'marvell,armada370-nand'
and assigns a compatible data of type enum pxa3xx_nand_variant to allow
such distinction.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If the nand chip provides us the ECC info, we can use it firstly.
The set_geometry_by_ecc_info() will use the ECC info, and
calculate the parameters we need.
Rename the old code to legacy_set_geometry() which will takes effect
when there is no ECC info from the nand chip or we fails in the ECC info case.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the ecc info for TC58NVG2S0F, TC58NVG3S0F, TC58NVG5D2 and TC58NVG6D2.
From these chips' datasheets, we know that:
The TC58NVG2S0F and TC58NVG3S0F require 4bit ECC for per 512byte.
The TC58NVG5D2 and TC58NVG6D2 require 40bits ECC for per 1024byte.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Parse out the ECC information for the full-id nand chips.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The current code uses the hardcode to detect the 16-bit bus width.
Use the onfi_feature() to replace it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
[Brian: small fixup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since the ONFI 2.1, the onfi spec adds the Extended Parameter Page
to store the ECC info.
The onfi spec tells us that if the nand chip's recommended ECC codeword
size is not 512 bytes, then the @ecc_bits is 0xff. The host _SHOULD_ then
read the Extended ECC information that is part of the extended parameter
page to retrieve the ECC requirements for this device.
This patch implement the reading of the Extended Parameter Page, and parses
the sections for ECC type, and get the ECC info from the ECC section.
Tested this patch with Micron MT29F64G08CBABAWP.
Acked-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
From the ONFI spec, we can just get the ECC info from the @ecc_bits field of
the parameter page.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Reviewed-and-tested-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
It is better to do the sanity check for the parameter before any hardware
operation.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use NAND_CI_CELLTYPE_MSK to extract the cell type from nand_chip.cellinfo
instead of hardcoded constant.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch fix following warning:
drivers/mtd/nand/atmel_nand.c:2007: warning: 'atmel_nand_nfc_match' defined but not used
This patch add '#if defined(CONFIG_OF)' block to guard around the definition
of atmel_nand_nfc_match, in order to avoid the warning when the kernel is
configured without DT support.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use mtdtest_write() and mtdtest_erase_eraseblock() in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Iwo Mergler <Iwo.Mergler@netcommwireless.com.au>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use mtdtest_scan_for_bad_eraseblocks() and mtdtest_erase_good_eraseblocks()
in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use mtdtest_scan_for_bad_eraseblocks() and mtdtest_erase_good_eraseblocks()
in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use mtdtest_read(), mtdtest_write(), mtdtest_erase_eraseblock(), and
mtdtest_scan_for_bad_eraseblocks() in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use mtdtest_read() and mtdtest_scan_for_bad_eraseblocks() in mtd_test
helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Use mtdtest_scan_for_bad_eraseblocks(), mtdtest_erase_good_eraseblocks(),
and mtdtest_erase_eraseblock() in mtd_test helpers.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Each mtd test module have a single source whose name is the same as
the module name. In order to link a single object including helper
functions to every test module, this rename these sources to the
different names.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This introduces the helper functions which can be used by several
mtd/tests modules.
The following three functions are used all over the test modules.
- mtdtest_erase_eraseblock()
- mtdtest_scan_for_bad_eraseblocks()
- mtdtest_erase_good_eraseblocks()
The following are wrapper functions for mtd_read() and mtd_write()
which can simplify the return value check.
- mtdtest_read()
- mtdtest_write()
All helpers are put into a single .c file and it will be linked to
every test module later. The code will actually be copied to every
test module, but it is fine for our small test infrastructure.
[dwmw2: merge later 'return -EIO when mtdtest_read() failed' fix]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Vikram Narayanan <vikram186@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
NAND_BBT_SCANEMPTY is a strange, badly-supported option with omap as its
single remaining user.
NAND_BBT_SCANEMPTY was likely used by accident in omap2[1]. And anyway,
omap2 doesn't scan the chip for bad blocks (courtesy of
NAND_SKIP_BBTSCAN), and so its use of this option is irrelevant.
This patch drops the NAND_BBT_SCANEMPTY option.
[1] http://lists.infradead.org/pipermail/linux-mtd/2012-July/042902.html
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
nand_base.c shouldn't have to know the implementation details of
nand_bbt's in-memory BBT. Specifically, nand_base shouldn't perform the
bit masking and shifting to isolate a BBT entry.
Instead, just move some of the BBT code into a new nand_markbad_bbt()
interface. This interface allows external users (i.e., nand_base) to
mark a single block as bad in the BBT. Then nand_bbt will take care of
modifying the in-memory BBT and updating the flash-based BBT (if
applicable).
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
