streamzap uses 'struct timeval' to store the start time of a signal for
gap tracking. struct timeval uses a 32-bit seconds representation which
will overflow in year 2038 and beyond. Replace struct timeval with ktime_t
which uses a 64-bit seconds representation and is 2038 safe. This patch
uses ktime_get_real() preserving the use of wall-clock time in the
original code.
Signed-off-by: Tina Ruchandani <ruchandani.tina@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
rc-main mistakenly uses #ifdef MODULE to determine whether it should
load the rc keymap modules. This symbol is only defined if rc-main
is being built as a module itself, and bears no relation to whether
the rc keymaps are modules.
Fix this to use CONFIG_MODULES instead.
Fixes: 631493ecac ("[media] rc-core: merge rc-map.c into rc-main.c")
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Many decoders require a trailing space (period without IR illumination)
to be delivered before completing a decode.
Since the gpio-ir-recv driver only delivers events on gpio transitions,
a single IR symbol (caused by a quick touch on an IR remote) will not
be properly decoded without the use of a timer to flush the tail end
state of the IR receiver.
This patch initializes and uses a timer and the timeout field of rcdev
to complete the stream and allow decode.
The timeout can be overridden through the use of the LIRC_SET_REC_TIMEOUT
ioctl.
Signed-off-by: Eric Nelson <eric@nelint.com>
Acked-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The device is set as wakeup capable using proper wakeup API but the
driver misuses IRQF_NO_SUSPEND to set the interrupt as wakeup source
which is incorrect.
This patch removes the use of IRQF_NO_SUSPEND flags replacing it with
enable_irq_wake instead.
Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Let's not mix platform_data headers with the core headers. Instead, let's
create a subdir at linux/platform_data and move the headers to that
common place, adding it to MAINTAINERS.
The headers were moved with:
mkdir include/linux/platform_data/media/; git mv include/media/gpio-ir-recv.h include/media/ir-rx51.h include/media/mmp-camera.h include/media/omap1_camera.h include/media/omap4iss.h include/media/s5p_hdmi.h include/media/si4713.h include/media/sii9234.h include/media/smiapp.h include/media/soc_camera.h include/media/soc_camera_platform.h include/media/timb_radio.h include/media/timb_video.h include/linux/platform_data/media/
And the references fixed with this script:
MAIN_DIR="linux/platform_data/"
PREV_DIR="media/"
DIRS="media/"
echo "Checking affected files" >&2
for i in $DIRS; do
for j in $(find include/$MAIN_DIR/$i -type f -name '*.h'); do
n=`basename $j`
git grep -l $n
done
done|sort|uniq >files && (
echo "Handling files..." >&2;
echo "for i in \$(cat files|grep -v Documentation); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo "perl -ne 's,(include [\\\"\\<])$PREV_DIR($i)([\\\"\\>]),\1$MAIN_DIR$j\2\3,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done";
);
echo "Handling documentation..." >&2;
echo "for i in MAINTAINERS \$(cat files); do cat \$i | \\";
(
cd include/$MAIN_DIR;
for j in $DIRS; do
for i in $(ls $j); do
echo " perl -ne 's,include/$PREV_DIR($i)\b,include/$MAIN_DIR$j\1,; print \$_' |\\";
done;
done;
echo "cat > a && mv a \$i; done"
);
) >script && . ./script
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
This reverts commit 9869da5bac.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 1d971d927e.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit a0466f15b4.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit cf257e288a.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 0d830b2d12.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 2e4ebde269.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit da7ee60b03.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 275ddb40bc removed the lirc
"protocol" but kept backwards compatibility by always listing
the protocol as present and enabled. This patch further improves
the logic by only listing the protocol if the lirc module is loaded
(or if lirc is builtin).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This changes the keymap back to the state before commit 616a4b83
and changes the driver to use full NEC32 scancodes following the
instructions provided by Malcolm Priestley <tvboxspy@gmail.com>.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The LIRC protocol was always a bad fit and if we're ever going to expose
protocol numbers in a user-space API, it'd be better to get rid of the
LIRC "protocol" first.
The sysfs API is kept backwards compatible by always listing the lirc
protocol as present and enabled.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch changes rc-core to use the kernel facilities that are already
available for handling unique numbers instead of rolling its own bitmap
stuff.
Signed-off-by: David Härdeman <david@hardeman.nu>
Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The input_dev is already gone when the rc device is being unregistered
so checking for its presence only means that no remove uevent will be
generated.
Cc: stable@kernel.org
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The RC_ST and IR_SUNXI entries have weird indentation, and the RC_ST
entry is actually malformed. Fix it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Using CONFIG_PM_SLEEP suppress the warnings when the driver is
compiled without PM sleep functions:
drivers/media/rc/st_rc.c:338:12: warning: ‘st_rc_suspend’ defined but not used [-Wunused-function]
drivers/media/rc/st_rc.c:359:12: warning: ‘st_rc_resume’ defined but not used [-Wunused-function]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This RC map was taken from Christoph Pinkl's patch
(http://patchwork.linuxtv.org/patch/7217/). It is used solely by the respective
mantis based card because the encoding is not known.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The TS35 remote is distributed with TechniSat CableStar HD2 cards (mantis
chipset). The exact protocol type is unknown, making this rc map probably only
usable by mantis cards.
Signed-off-by: Jan Klötzke <jan@kloetzke.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Don't allow sleep when getting the gpio value in the irq-handler.
On my rk3288 board this results in might_sleep warnings when receiving
data like:
BUG: sleeping function called from invalid context at drivers/gpio/gpiolib.c:1531
in_atomic(): 1, irqs_disabled(): 128, pid: 0, name: swapper/0
CPU: 0 PID: 0 Comm: swapper/0 Tainted: P 4.1.0-rc5+ #2011
Hardware name: Rockchip (Device Tree)
[<c00189a0>] (unwind_backtrace) from [<c0013b04>] (show_stack+0x20/0x24)
[<c0013b04>] (show_stack) from [<c0757970>] (dump_stack+0x8c/0xbc)
[<c0757970>] (dump_stack) from [<c0053188>] (___might_sleep+0x238/0x284)
[<c0053188>] (___might_sleep) from [<c0053264>] (__might_sleep+0x90/0xa4)
[<c0053264>] (__might_sleep) from [<c02ff4ac>] (gpiod_get_raw_value_cansleep+0x28/0x44)
[<c02ff4ac>] (gpiod_get_raw_value_cansleep) from [<bf0363c4>] (gpio_ir_recv_irq+0x24/0x6c [gpio_ir_recv])
[<bf0363c4>] (gpio_ir_recv_irq [gpio_ir_recv]) from [<c008a78c>] (handle_irq_event_percpu+0x164/0x550)
[<c008a78c>] (handle_irq_event_percpu) from [<c008abc4>] (handle_irq_event+0x4c/0x6c)
[<c008abc4>] (handle_irq_event) from [<c008df88>] (handle_edge_irq+0x128/0x150)
[<c008df88>] (handle_edge_irq) from [<c0089edc>] (generic_handle_irq+0x30/0x40)
[<c0089edc>] (generic_handle_irq) from [<c02fc4cc>] (rockchip_irq_demux+0x158/0x210)
[<c02fc4cc>] (rockchip_irq_demux) from [<c0089edc>] (generic_handle_irq+0x30/0x40)
[<c0089edc>] (generic_handle_irq) from [<c008a058>] (__handle_domain_irq+0x98/0xc0)
[<c008a058>] (__handle_domain_irq) from [<c00094a4>] (gic_handle_irq+0x4c/0x70)
[<c00094a4>] (gic_handle_irq) from [<c0014684>] (__irq_svc+0x44/0x5c)
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Nuvoton-cir utilizes the encoding capabilities of rc-core to convert
scancodes from user space to pulse/space format understood by the
underlying hardware.
Converted samples are then written to the wakeup fifo along with other
necessary configuration to enable wake up functionality.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the s_wakeup_filter callback to the rc-loopback driver, which instead of
setting the filter just feeds the scancode back through the input device
so that it can be verified.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support in rc-core for drivers which implement the wakeup scancode
filter by encoding the scancode using the raw IR encoders. This is by
way of rc_dev::encode_wakeup which should be set to true to make the
allowed wakeup protocols the same as the set of raw IR encoders.
As well as updating the sysfs interface to know which wakeup protocols
are allowed for encode_wakeup drivers, also ensure that the IR
decoders/encoders are loaded when an encode_wakeup driver is registered.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the capability to encode RC-6 and RC-6A scancodes as raw events.
The protocol is chosen based on the specified protocol mask, and
whether all the required bits are set in the scancode mask, and none of
the unused bits are set in the scancode data.
The Manchester modulation helper is used several times with various
timings so that RC-6 header preamble, the header, header trailing bit
and the data itself can be modulated correctly.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: James Hogan <james@albanarts.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add the capability to encode RC-5, RC-5X and RC-5-SZ scancodes as raw
events. The protocol is chosen based on the specified protocol mask,
and whether all the required bits are set in the scancode mask, and
none of the unused bits are set in the scancode data. For example a
scancode filter with bit 16 set in both data and mask is unambiguously
RC-5X.
The Manchester modulation helper is used, and for RC-5X it is used twice
with two sets of timings, the first with a short trailer space for the
space in the middle, and the second with no leader so that it can
continue the space.
The encoding in RC-5-SZ first inserts a pulse and then simply utilizes
the generic Manchester encoder available in rc-core.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Adding a simple Manchester encoder to rc-core.
Manchester coding is used by at least RC-5 and RC-6 protocols and their
variants.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: James Hogan <james@albanarts.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a callback to raw ir handlers for encoding and modulating a scancode
to a set of raw events. This could be used for transmit, or for
converting a wakeup scancode filter to a form that is more suitable for
raw hardware wake up filters.
Signed-off-by: James Hogan <james@albanarts.com>
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Cc: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Building for avr32 leads the following build warning:
drivers/media/rc/st_rc.c:270: warning: passing argument 1 of 'IS_ERR' discards qualifiers from pointer target type
drivers/media/rc/st_rc.c:271: warning: passing argument 1 of 'PTR_ERR' discards qualifiers from pointer target type
devm_ioremap_resource() returns void __iomem *, so change 'base' and
'rx_base' definitions accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Building for avr32 leads the following build warning:
drivers/media/rc/ir-hix5hd2.c:221: warning: passing argument 1 of 'IS_ERR' discards qualifiers from pointer target type
drivers/media/rc/ir-hix5hd2.c:222: warning: passing argument 1 of 'PTR_ERR' discards qualifiers from pointer target type
devm_ioremap_resource() returns void __iomem *, so change 'base' definition
accordingly.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver does not use any PCI IDs, don't include
the pci_ids.h header.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
[mchehab@osg.samsung.com: fix a merge conflict at adv7604.c]
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
redrat3_send_cmd() can return an error or the read data. However,
it currently returns an u8, as reported by smatch:
drivers/media/rc/redrat3.c:416 redrat3_send_cmd() warn: signedness bug returning '(-12)'
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some false-positive warnings produced by smatch:
drivers/media/rc/ir-sony-decoder.c:129 ir_sony_decode() warn: missing break? reassigning 'data->state'
drivers/media/rc/ir-sony-decoder.c:137 ir_sony_decode() warn: missing break? reassigning 'data->state'
drivers/media/rc/ir-sony-decoder.c:165 ir_sony_decode() warn: missing break? reassigning 'data->state'
This is due to the logic used there to detect the need of a break.
While those are false positives, it is easy to get rid of them without
any drawbacks. The side effect is a cleaner function, with is good.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/rc/rc-main.c:749 rc_close() warn: inconsistent indenting
There's an extra space there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
img_ir_remove() passes a pointer to the ISR function as the 2nd
parameter to irq_free() instead of a pointer to the device data
structure.
This issue causes unloading img-ir module to fail with the below
warning after building and loading img-ir as a module.
WARNING: CPU: 2 PID: 155 at ../kernel/irq/manage.c:1278
__free_irq+0xb4/0x214() Trying to free already-free IRQ 58
Modules linked in: img_ir(-)
CPU: 2 PID: 155 Comm: rmmod Not tainted 3.14.0 #55 ...
Call Trace:
...
[<8048d420>] __free_irq+0xb4/0x214
[<8048d6b4>] free_irq+0xac/0xf4
[<c009b130>] img_ir_remove+0x54/0xd4 [img_ir] [<8073ded0>]
platform_drv_remove+0x30/0x54 ...
Fixes: 160a8f8aec ("[media] rc: img-ir: add base driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Cc: <stable@vger.kernel.org> # 3.15+
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Gets a handle to the system clock, already described in the binding
document, and calls the appropriate common clock framework functions
to mark it prepared/enabled, the common clock framework initially
enables the clock and doesn't disable it at least until the
device/driver is removed.
It's important the systen clock is enabled before register interface is
accessed by the driver.
The system clock to IR is needed for the driver to communicate with the
IR hardware via MMIO accesses on the system bus, so it must not be
disabled during use or the driver will malfunction.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Removing some boilerplate by using module_pnp_driver instead of calling
register and unregister in the otherwise empty init/exit functions
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We have to check pointer for NULL and then dereference it.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for the larger fifo found on sun5i and sun6i, having a separate
compatible for the ir found on sun5i & sun6i also is useful if we ever want
to add ir transmit support, because the sun5i & sun6i version do not have
transmit support.
Note this commits also adds checking for the end-of-packet interrupt flag
(which was already enabled), as the fifo-data-available interrupt flag only
gets set when the trigger-level is exceeded. So far we've been getting away
with not doing this because of the low trigger-level, but this is something
which we should have done since day one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
On sun6i the cir block is attached to the reset controller, add support
for de-asserting the reset if a reset controller is specified in dt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Since commit da6e162d6a ("[media] rc-core: simplify sysfs code"), when
the IR protocol is set using the sysfs interface to the same set of
protocols that are already set, store_protocols() does not refresh the
scancode filter with the new protocol, even if it has already called the
change_protocol() callback successfully. This results in the filter
being disabled in the hardware and not re-enabled until the filter is
set again using sysfs.
Fix in store_protocols() by still re-applying the filter whenever the
change_protocol() driver callback succeeded.
The problem can be reproduced with the img-ir driver by setting a
filter, and then setting the protocol to the same protocol that is
already set:
$ echo nec > protocols
$ echo 0xffff > filter_mask
$ echo nec > protocols
After this, messages which don't match the filter were still being
received.
Fixes: da6e162d6a ("[media] rc-core: simplify sysfs code")
Reported-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: David Härdeman <david@hardeman.nu>
Cc: <stable@vger.kernel.org> # v3.17+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Biphase decoding in the current img-ir has got a quirk, where multiple
Interrupts are generated when an incomplete IR code is received by the
decoder.
Patch adds a work around for the quirk and enables biphase decoding.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add toggle bit to struct img_ir_scancode_req so that protocols can
provide it to img_ir_handle_data(), and pass that toggle bit up to
rc_keydown instead of 0.
This is needed for the upcoming rc-5 and rc-6 patches.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The information being requested of hardware decode callbacks through
the img-ir-hw scancode API is mounting up, so combine it into a struct
which can be passed in with a single pointer rather than multiple
pointer arguments. This allows it to be extended more easily without
touching all the hardware decode callbacks.
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=i7gx
-----END PGP SIGNATURE-----
Merge tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Two new dvb frontend drivers: mn88472 and mn88473
- A new driver for some PCIe DVBSky cards
- A new remote controller driver: meson-ir
- One LIRC staging driver got rewritten and promoted to mainstream:
igorplugusb
- A new tuner driver (m88rs6000t)
- The old omap2 media driver got removed from staging. This driver
uses an old DMA API and it is likely broken on recent kernels.
Nobody cared enough to fix it
- Media bus format moved to a separate header, as DRM will also use the
definitions there
- mem2mem_testdev were renamed to vim2m, in order to use the same
naming convention taken by the other virtual test driver (vivid)
- Added a new driver for coda SoC (coda-jpeg)
- The cx88 driver got converted to use videobuf2 core
- Make DMABUF export buffer to work with DMA Scatter/Gather and Vmalloc
cores
- Lots of other fixes, improvements and cleanups on the drivers.
* tag 'media/v3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (384 commits)
[media] mn88473: One function call less in mn88473_init() after error
[media] mn88473: Remove uneeded check before release_firmware()
[media] lirc_zilog: Deletion of unnecessary checks before vfree()
[media] MAINTAINERS: Add myself as img-ir maintainer
[media] img-ir: Don't set driver's module owner
[media] img-ir: Depend on METAG or MIPS or COMPILE_TEST
[media] img-ir/hw: Drop [un]register_decoder declarations
[media] img-ir/hw: Fix potential deadlock stopping timer
[media] img-ir/hw: Always read data to clear buffer
[media] redrat3: ensure dma is setup properly
[media] ddbridge: remove unneeded check before dvb_unregister_device()
[media] si2157: One function call less in si2157_init() after error
[media] tuners: remove uneeded checks before release_firmware()
[media] arm: omap2: rx51-peripherals: fix build warning
[media] stv090x: add an extra protetion against buffer overflow
[media] stv090x: Remove an unreachable code
[media] stv090x: Some whitespace cleanups
[media] em28xx: checkpatch cleanup: whitespaces/new lines cleanups
[media] si2168: add support for firmware files in new format
[media] si2168: debug printout for firmware version
...
The ImgTec Infrared decoder block which img-ir drives is only used in
IMGWorks SoCs so far, such as the TZ1090 (Meta based) and the upcoming
Pistachio (MIPS based). Therefore make the driver depend on METAG (for
TZ1090) or MIPS (for Pistachio) or COMPILE_TEST (so that it is included
in x86 allmodconfig builds), to avoid cluttering the Kconfig menu with
drivers for hardware that isn't yet available on other platforms.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The img_ir_register_decoder() and img_ir_unregister_decoder() functions
were dropped prior to the img-ir driver being applied to simplify the
protocol decoder setup. However the declarations of these functions in
img-ir-hw.h were still included. Delete them since they're completely
unused.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The end timer is used for switching back from repeat code timings when
no repeat codes have been received for a certain amount of time. When
the protocol is changed, the end timer is deleted synchronously with
del_timer_sync(), however this takes place while holding the main spin
lock, and the timer handler also needs to acquire the spin lock.
This opens the possibility of a deadlock on an SMP system if the
protocol is changed just as the repeat timer is expiring. One CPU could
end up in img_ir_set_decoder() holding the lock and waiting for the end
timer to complete, while the other CPU is stuck in the timer handler
spinning on the lock held by the first CPU.
Lockdep also spots a possible lock inversion in the same code, since
img_ir_set_decoder() acquires the img-ir lock before the timer lock, but
the timer handler will try and acquire them the other way around:
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.18.0-rc5+ #957 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(((&hw->end_timer))){+.-...}, at: [<4006ae5c>] _call_timer_fn+0x0/0xfc
but this lock was taken by another, HARDIRQ-safe lock in the past:
(&(&priv->lock)->rlock#2){-.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(((&hw->end_timer)));
local_irq_disable();
lock(&(&priv->lock)->rlock#2);
lock(((&hw->end_timer)));
<Interrupt>
lock(&(&priv->lock)->rlock#2);
*** DEADLOCK ***
This is fixed by releasing the main spin lock while performing the
del_timer_sync() call. The timer is prevented from restarting before the
lock is reacquired by a new "stopping" flag which img_ir_handle_data()
checks before updating the timer.
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(((&hw->end_timer))){+.-...}, at: [<4006ae5c>] _call_timer_fn+0x0/0xfc
but this lock was taken by another, HARDIRQ-safe lock in the past:
(&(&priv->lock)->rlock#2){-.....}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(((&hw->end_timer)));
local_irq_disable();
lock(&(&priv->lock)->rlock#2);
lock(((&hw->end_timer)));
<Interrupt>
lock(&(&priv->lock)->rlock#2);
*** DEADLOCK ***
This is fixed by releasing the main spin lock while performing the
del_timer_sync() call. The timer is prevented from restarting before the
lock is reacquired by a new "stopping" flag which img_ir_handle_data()
checks before updating the timer.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Sifan Naeem <sifan.naeem@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A problem was found on Polaris where if the unit it booted via the power
button on the infrared remote then the next button press on the remote
would return the key code used to power on the unit.
The sequence is:
- The polaris powered off but with the powerdown controller (PDC) block
still powered.
- Press power key on remote, IR block receives the key.
- Kernel starts, IR code is in IMG_IR_DATA_x but neither IMG_IR_RXDVAL
or IMG_IR_RXDVALD2 are set.
- Wait any amount of time.
- Press any key.
- IMG_IR_RXDVAL or IMG_IR_RXDVALD2 is set but IMG_IR_DATA_x is
unchanged since the powerup key data was never read.
This is worked around by always reading the IMG_IR_DATA_x in
img_ir_set_decoder(), rather than only when the IMG_IR_RXDVAL or
IMG_IR_RXDVALD2 bit is set.
Signed-off-by: Dylan Rajaratnam <dylan.rajaratnam@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This fixes the driver on arm.
Reported-by: Steven Guitton <keltiek@gmail.com>
Tested-by: Steven Guitton <keltiek@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Amlogic Meson SoCs include a infrared remote control receiver that can
operate in two modes: "NEC" mode in which the hardware decodes frames
using the NEC IR protocol, and "general" mode in which the receiver
simply reports the duration of pulses and spaces for software
decoding.
This is a driver for the IR receiver that implements software decoding
of received frames.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The functions input_free_device() and rc_close() test whether their argument
is NULL and then return immediately. Thus the test around the call
is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The toggle bit shouldn't be cleared before the toggle value is calculated.
This should probably go into 3.17.x as well.
Fixes: 120703f9eb ([media] rc-core: document the protocol type)
Cc: stable@vger.kernel.org # For v3.17
Tested-by: Stephan Raue <mailinglists@openelec.tv>
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
As reported by smatch:
drivers/media/rc/rc-main.c:1426 rc_register_device() warn: should '1 << rc_map->rc_type' be a 64 bit type?
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Userspace expects to see a long space before the first pulse is sent on
the lirc device. Currently, if a long time has passed and a new packet
is started, the lirc codec just returns and doesn't send anything. This
makes lircd ignore many perfectly valid signals unless they are sent in
quick sucession. When a reset event is delivered, we cannot know
anything about the duration of the space. But it should be safe to
assume it has been a long time and we just set the duration to maximum.
Signed-off-by: Austin Lund <austin.lund@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a complete re-write inspired by the original lirc driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
With kernel 3.17 the imon remote control for device 15c2:0034 does not
work anymore, which uses the OTHER protocol. Only the front panel
buttons which uses the RC6 protocol are working.
Adds the missing comparison for the RC_BIT_OTHER.
Cc: stable@vger.kernel.org # for Kernel 3.17
Signed-off-by: Ulrich Eckhardt <uli@uli-eckhardt.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Change CONFIG_PM to CONFIG_PM_SLEEP to solve
warning: 'hix5hd2_ir_suspend' & 'hix5hd2_ir_resume' defined but not used
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Changeset e87b540be2 broke RC5-SZ decoding, as it forgot to add
the extra bit check for the enabled protocols at the beginning of
the logic.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
IR receiver using nuvoton-cir and lirc required additional configuration
steps after upgrade from kernel 3.16 to 3.17-rcX. Bisected regression to
commit da6e162d6a ("[media] rc-core:
simplify sysfs code").
The regression comes from adding function change_protocol in ir-raw.c.
It changes behaviour so that only the protocol enabled by driver's
map_name will be active after registration. This breaks user space
behaviour, lirc does not get key press signals anymore.
Enable lirc protocol by default for ir raw decoders to restore original
behaviour.
Cc: stable@vger.kernel.org # for v3.17
Signed-off-by: Tomas Melin <tomas.melin@iki.fi>
Acked-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DUbD
-----END PGP SIGNATURE-----
Merge tag 'media/v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new IR driver: hix5hd2-ir
- the virtual test driver (vivi) was replaced by vivid, with has an
almost complete set of features to emulate most v4l2 devices and
properly test all sorts of userspace apps
- the as102 driver had several bugs fixed and was properly split into a
frontend and a core driver. With that, it got promoted from staging
into mainstream
- one new CI driver got added for CIMaX SP2/SP2HF (sp2 driver)
- one new frontend driver for Toshiba ISDB-T/ISDB-S demod (tc90522)
- one new PCI driver for ISDB-T/ISDB-S (pt3 driver)
- saa7134 driver got support for go7007-based devices
- added a new PCI driver for Techwell 68xx chipsets (tw68)
- a new platform driver was added (coda)
- new tuner drivers: mxl301rf and qm1d1c0042
- a new DVB USB driver was added for DVBSky S860 & similar devices
- added a new SDR driver (hackrf)
- usbtv got audio support
- several platform drivers are now compiled with COMPILE_TEST
- a series of compiler fixup patches, making sparse/spatch happier with
the media stuff and removing several warnings, especially on those
platform drivers that didn't use to compile on x86
- Support for several new modern devices got added
- lots of other fixes, improvements and cleanups
* tag 'media/v3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (544 commits)
[media] ir-hix5hd2: fix build on c6x arch
[media] pt3: fix DTV FE I2C driver load error paths
Revert "[media] media: em28xx - remove reset_resume interface"
[media] exynos4-is: fix some warnings when compiling on arm64
[media] usb drivers: use %zu instead of %zd
[media] pci drivers: use %zu instead of %zd
[media] dvb-frontends: use %zu instead of %zd
[media] s5p-mfc: Fix several printk warnings
[media] s5p_mfc_opr: Fix warnings
[media] ti-vpe: Fix typecast
[media] s3c-camif: fix dma_addr_t printks
[media] s5p_mfc_opr_v6: get rid of warnings when compiled with 64 bits
[media] s5p_mfc_opr_v5: Fix lots of warnings on x86_64
[media] em28xx: Fix identation
[media] drxd: remove a dead code
[media] saa7146: remove return after BUG()
[media] cx88: remove return after BUG()
[media] cx88: fix cards table CodingStyle
[media] radio-sf16fmr2: declare some structs as static
[media] radio-sf16fmi: declare pnp_attached as static
...
While not all archs have readl_relaxed, we need to add a hack at the
driver to allow it to COMPILE_TEST on all archs:
drivers/media/rc/ir-hix5hd2.c: In function ‘hix5hd2_ir_config’:
drivers/media/rc/ir-hix5hd2.c💯2: error: implicit declaration of function ‘readl_relaxed’ [-Werror=implicit-function-declaration]
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch moves setting of pm_ops out of the CONFIG_PM_SLEEP condition.
Setting pm ops under CONFIG_PM_SLEEP does not make any sense.
This patch also remove unnecessary also remove CONFIG_PM condition for pm
member in st_rc_driver structure.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch fixes a compilation error while building with the
random kernel configuration.
drivers/media/rc/st_rc.c: In function 'st_rc_probe':
drivers/media/rc/st_rc.c:281:2: error: implicit declaration of
function 'reset_control_get' [-Werror=implicit-function-declaration]
rc_dev->rstc = reset_control_get(dev, NULL);
drivers/media/rc/st_rc.c:281:15: warning: assignment makes pointer
from integer without a cast [enabled by default]
rc_dev->rstc = reset_control_get(dev, NULL);
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
IR transmitter driver for Hisilicon hix5hd2 soc
By default all protocols are disabled.
For example nec decoder can be enabled by either
1. ir-keytable -p nec
2. echo nec > /sys/class/rc/rc0/protocols
See see Documentation/ABI/testing/sysfs-class-rc
[mchehab@osg.samsung.com: Add a fixup for the driver to compile on
archs that don't provide writel_relaxed() macro]
Signed-off-by: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This is a RC5 remote controller map for DVBSky S860/960 devices.
Signed-off-by: Nibble Max <nibble.max@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
imon_probe() does three usb_get_dev(), but there is no any
usb_put_dev() in the driver.
The patch adds usb_put_dev() to error paths, to imon_disconnect()
and to imon_probe() as far as usbdev is not saved anywhere.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
mceusb_init_rc_dev() does usb_get_dev(), but there is no any
usb_put_dev() in the driver.
The patch tries to straighten logic. It moves usb_get_dev()
directly to mceusb_dev_probe() and adds usb_put_dev() to an error path
and to mceusb_dev_disconnect().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch introduces the use of !usb_endpoint_dir_in(epd) and
!usb_endpoint_xfer_int(epd).
The Coccinelle semantic patch that makes these changes is as follows:
- ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) !=
- \(USB_DIR_IN\|0x80\))
+ !usb_endpoint_dir_in(epd)
@@ struct usb_endpoint_descriptor *epd; @@
- ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) !=
- \(USB_ENDPOINT_XFER_INT\|3\))
+ !usb_endpoint_xfer_int(epd)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch introduces the use of the function usb_endpoint_type.
The Coccinelle semantic patch that makes these changes is as follows:
@@ struct usb_endpoint_descriptor *epd; @@
- (epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\))
+ usb_endpoint_type(epd)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Instead of allocating a var to store 0 and just return it,
change the code to return 0 directly.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
drivers/media/rc/img-ir/img-ir-nec.c:111:23: warning: symbol 'img_ir_nec' was not declared. Should it be static?
drivers/media/rc/img-ir/img-ir-jvc.c:54:23: warning: symbol 'img_ir_jvc' was not declared. Should it be static?
drivers/media/rc/img-ir/img-ir-sony.c:120:23: warning: symbol 'img_ir_sony' was not declared. Should it be static?
drivers/media/rc/img-ir/img-ir-sharp.c:75:23: warning: symbol 'img_ir_sharp' was not declared. Should it be static?
drivers/media/rc/img-ir/img-ir-sanyo.c:82:23: warning: symbol 'img_ir_sanyo' was not declared. Should it be static?
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several arch-specific media drivers that don't
require asm-specific includes and can be successfully
compiled on x86. Add COMPILE_TEST dependency for them, in
order to allow a broader test on those drivers.
That helps static analysis tools like Coverity to discover
eventual troubles there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
