Add ability to configure chip select (CS) parameters for devices
that need different CS parameters setup after their configuration.
I.e. an FPGA device on LP bus can require different CS parameters
for its bus interface after loading firmware into it. A driver
can easily reconfigure the LPC CS parameters using this function.
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Early driver probing can fail due to not available clocks
(clk_get() fails) since the clk API init didn't take place yet.
Move clocks init before bus probing.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The .dtsi now names all PSC nodes as "psc", so this ac97
check won't work. Check for ac97 PSC using compatible
property.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
If the DIU framebuffer driver is not enabled, then there's no point in
compiling any platform DIU code, because it will never be used. Most of
the platform code was protected in the appropriate #ifdef, but not all.
This caused a break in some randconfig builds.
This is only a problem on the 512x platforms. The P1022DS and MPC8610HPCD
platforms are already correct.
This patch reverts commit 12e36309f8 ("powerpc:
Option FB_FSL_DIU is not really optional for mpc512x") and restores the
ability to configure DIU support.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
In powerpc randconfig builds, this keeps showing up:
CC arch/powerpc/platforms/512x/mpc512x_shared.o
arch/powerpc/platforms/512x/mpc512x_shared.c:70:9: warning: 'enum fsl_diu_monitor_port' declared inside parameter list
arch/powerpc/platforms/512x/mpc512x_shared.c:70:9: warning: its scope is only this definition or declaration, which is probably not what you want
arch/powerpc/platforms/512x/mpc512x_shared.c:69:56: error: parameter 1 ('port') has incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:69:5: warning: function declaration isn't a prototype
arch/powerpc/platforms/512x/mpc512x_shared.c:84:9: warning: 'enum fsl_diu_monitor_port' declared inside parameter list
arch/powerpc/platforms/512x/mpc512x_shared.c:83:56: error: parameter 1 ('port') has incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:83:6: warning: function declaration isn't a prototype
arch/powerpc/platforms/512x/mpc512x_shared.c:88:36: warning: 'enum fsl_diu_monitor_port' declared inside parameter list
arch/powerpc/platforms/512x/mpc512x_shared.c:88:57: error: parameter 1 ('port') has incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:88:6: warning: function declaration isn't a prototype
arch/powerpc/platforms/512x/mpc512x_shared.c:187:54: error: parameter 1 ('port') has incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:187:1: error: return type is an incomplete type
arch/powerpc/platforms/512x/mpc512x_shared.c:187:1: warning: function declaration isn't a prototype
arch/powerpc/platforms/512x/mpc512x_shared.c: In function 'mpc512x_valid_monitor_port':
arch/powerpc/platforms/512x/mpc512x_shared.c:189:9: error: 'FSL_DIU_PORT_DVI' undeclared (first use in this function)
arch/powerpc/platforms/512x/mpc512x_shared.c:189:9: note: each undeclared identifier is reported only once for each function it appears in
arch/powerpc/platforms/512x/mpc512x_shared.c:189:2: warning: 'return' with a value, in function returning void
make[2]: *** [arch/powerpc/platforms/512x/mpc512x_shared.o] Error 1
The reason is that mpc512x_shared.c has a couple token #ifdef
on FB_FSL_DIU/FB_FSL_DIU_MODULE, but they don't come close to
masking all the DIU dependencies, as the above fail shows.
Rather than sprinkle more pointless #ifdef in this file, just
remove the existing two, and make FB_FSL_DIU part of the
dependency. The mpc512x_defconfig already has the line
"CONFIG_FB_FSL_DIU=y" so this change should be zero impact
on real world configs.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Make all the irq_domain_ops structures in powerpc 'static const'
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
There is no Kconfig symbol named MPC5121_ADS_CPLD. The select statement
for that symbol is a nop. Drop it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
So that we can clean up the header files and not be relying
on implicit includes from device.h ---> module.h
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The Freescale DIU video controller supports five video "modes", but only
the first two are used by the driver. The other three are special modes
that don't make sense for a framebuffer driver. Therefore, there's no
point in keeping a global variable that indicates which mode we're
supposed to use.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Move the driver to the place where it is expected to be nowadays. Also
rename its CONFIG-name to match the rest and adapt the defconfigs.
Finally, move selection of REQUIRE_GPIOLIB or WANTS_OPTIONAL_GPIOLIB to
the platforms, because this option is per-platform and not per-driver.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Instead of using ill-defined numbers (0, 1, and 2) for the monitor port, allow
the user to specify the port by name ("dvi", "lvds", or "dlvds"). This works
on the kernel command line, the module command-line, and the sysfs "monitor"
device.
Note that changing the monitor port does not currently work on the P1022DS,
because the code that talks to the PIXIS FPGA is broken.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
As NO_IRQ_IGNORE is only used between the static function cpld_pic_get_irq
and its caller cpld_pic_cascade, and cpld_pic_cascade only uses it to
suppress calling handle_generic_irq, we can change these uses to NO_IRQ
and remove the extra tests and pathlength in cpld_pic_cascade.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds of_flat_dt_match() which tests a node for
compatibility with a list of values and converts the relevant powerpc
platform code to use it. This approach simplifies the board support
code a bit.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com>
clk_get() should return an ERR_PTR value on error, not NULL.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'next-devicetree' of git://git.secretlab.ca/git/linux-2.6: (63 commits)
of/platform: Register of_platform_drivers with an "of:" prefix
of/address: Clean up function declarations
of/spi: call of_register_spi_devices() from spi core code
of: Provide default of_node_to_nid() implementation.
of/device: Make of_device_make_bus_id() usable by other code.
of/irq: Fix endian issues in parsing interrupt specifiers
of: Fix phandle endian issues
of/flattree: fix of_flat_dt_is_compatible() to match the full compatible string
of: remove of_default_bus_ids
of: make of_find_device_by_node generic
microblaze: remove references to of_device and to_of_device
sparc: remove references to of_device and to_of_device
powerpc: remove references to of_device and to_of_device
of/device: Replace of_device with platform_device in includes and core code
of/device: Protect against binding of_platform_drivers to non-OF devices
of: remove asm/of_device.h
of: remove asm/of_platform.h
of/platform: remove all of_bus_type and of_platform_bus_type references
of: Merge of_platform_bus_type with platform_bus_type
drivercore/of: Add OF style matching to platform bus
...
Fix up trivial conflicts in arch/microblaze/kernel/Makefile due to just
some obj-y removals by the devicetree branch, while the microblaze
updates added a new file.
MPC5121 DIU configuration/setup as initialized by the boot
loader currently will get lost while booting Linux. As a
result displaying the boot splash is not possible through
the boot process.
To prevent this we reserve configured DIU frame buffer
address range while booting and preserve AOI descriptor
and gamma table so that DIU continues displaying through
the whole boot process. On first open from user space
DIU frame buffer driver releases the reserved frame
buffer area and continues to operate as usual.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allows using clk_get()/clk_enable()/clk_disable() for VIU
clock in the v4l2 video driver.
Signed-off-by: Hongjun Chen <hong-jun.chen@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow board selection in a drop-down board sub-menu
like many other platforms do.
Before the patch:
...
[ ] Freescale MPC5121E ADS
[ ] Generic support for simple MPC5121 based boards
[ ] 52xx-based boards
...
Patched:
...
[*] 512x-based boards
[ ] Freescale MPC5121E ADS
[ ] Generic support for simple MPC5121 based boards
[ ] 52xx-based boards
...
This is a cleanup before adding new board selection entry.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
of_device is just a #define alias to platform_device. This patch
replaces all references to it with platform_device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since PSC could also be used in other modes than UART mode
we move PSC FIFO memory initialization from serial driver to
common platform code. The initialized FIFO memory slices may
not overlap, so the most easy way would be to configure them
all at once at init time for all PSC devices. This is now done
by this patch.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Now we use printf style alignment there is no need to manually space
these fields.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Instantiate NAND Flash Controller device if it's
description is found in the device tree.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add reset module registers representation and
machine restart callback for mpc5121 platform.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move mpc5121_clk_init() call to platform init code so it won't
get called on non-5121 platforms on a multiplatform kernel.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The typename member of struct irq_chip was kept for migration purposes
and is obsolete since more than 2 years. Fix up the leftovers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linuxppc-dev@ozlabs.org
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
get_irq_desc() is a powerpc-specific version of irq_to_desc(). That
is reason enough to remove it, but it also doesn't know about sparse
irq_desc support which irq_to_desc() does (when we enable it).
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch refactors clock.c by replacing printk calls with
pr_info/pr_cont, and uses '=' in output to connect key/value pairs
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
So far, MPC512x used mpc512x_find_ips_freq() to get the bus frequency,
while MPC52xx used mpc52xx_find_ipb_freq(). Despite the different
clock names (IPS vs. IPB) the code was identical.
Use common code for both processor families.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CONFIG_PPC_MULTIPLATFORM is a remain of the pre-powerpc days and isn't
really meaningful anymore. It was basically equivalent to PPC64 || 6xx.
This removes it along with the following changes:
- 32-bit platforms that relied on PPC32 && PPC_MULTIPLATFORM now rely
on 6xx which is what they want anyway.
- A new symbol, PPC_BOOK3S, is defined that represent compliance with
the "Server" variant of the architecture. This is set when either 6xx
or PPC64 is set and open the door for future BOOK3E 64-bit.
- 64-bit platforms that relied on PPC64 && PPC_MULTIPLATFORM now use
PPC64 && PPC_BOOK3S
- A separate and selectable CONFIG_PPC_OF_BOOT_TRAMPOLINE option is now
used to control the use of prom_init.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
strcmp on NULL results in a segmentation fault, also, remove the second,
redundant test on dev
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Uses mpc83xx_add_bridge in fsl_pci.c
Adds second register tuple to pci node register property
as done for 83xx device trees in a previous patch.
Signed-off-by: John Rigby <jrigby@freescale.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a interrupt host for the interrupt controller in the mpc5121ads cpld.
PCI interrupts are 0-7 the rest are 8-15 Touchscreen pendown irq is
hardwired to irq1 All other irqs are chained to irq0
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Move shared code from mpc5121_ads.c to new file mpc512x_shared.c
- mpc512x_find_ips_freq -> unchanged
- contents of mpc5121_ads_init_IRQ -> mpc512x_init_IRQ
- looking for fsl,mpc5121-ipic instead of fsl,ipic
- mpc5121_ads_declare_of_platform_devices -> mpc5121_declare_of_platform_devices
- and use compatible for lookup instead of node name
Add new generic board setup mpc5121_generic.c
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Plugs into the generic powerpc clock driver in
arch/powerpc/kernel/clock.c
The following subset of clk_interface is implemented:
clk_get, clk_put: get clock via name, release clock
clk_enable, clk_disable: enable or disable clock
clk_get_rate: get clock rate in Hz
clk_set_rate: stubbed
clk_round_rate: stubbed
clk_set_parent: NULL
clk_get_parent: NULL
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CONFIG_DEVICE_TREE was the only user of CONFIG_WANT_DEVICE_TREE but
it was removed in commit id 2543133381
(bootwrapper: Build multiple cuImages).
This removes CONFIG_WANT_DEVICE_TREE from Kconfig and the defconfigs.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
512x is very similar to 83xx and most
of this is patterned after code from 83xx.
New platform:
changed:
arch/powerpc/Kconfig
arch/powerpc/platforms/Kconfig
arch/powerpc/platforms/Kconfig.cputype
arch/powerpc/platforms/Makefile
new:
arch/powerpc/platforms/512x/*
include/asm-powerpc/mpc512x.h
Signed-off-by: John Rigby <jrigby@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
