As it was previously done for kirkwood and for aramda 370/XP, this adds
missing node labels to Armada 375 and SoC specific nodes to allow to
reference them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The gpio-key nodes do not have a reg property, so remove the address from
the unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The dsa node does not have a reg property, so remove the address from the
unit name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
l2-cache which is either an aurora-outer-cache or an aurora-system-cache
has a reg property so the unit name should contain an address.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a ranges property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
PCIe has a range property, so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
MDIO has a reg property so the unit name should contain an address.
Take the opportunity to use the node label instead of the full name.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Use the node label when possible. As a result it flattens the device tree
and it makes more visible the IP blocks specific to each SoC variant.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
As it was previously done for kirkwood, this adds missing node labels to
Armada 370 and XP common and SoC specific nodes to allow to reference
them more easily.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The cpurst nodes are identical in armada-370.dtsi and armada-xp.dtsi
files, so move it in the common armada-370-xp.dtsi file.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
In the dts for the Marvell Armada XP Matrix board the pcie-controller was
located under the internal-regs node whereas it belongs to the soc node.
It means that, until this fix, the pcie could not work for this board
because it didn't match the definition of the pcie-controller node in the
dtsi file. If we had a look on the decompiled dtb file we saw two
different instances of the pcie-controller node: one with the all the
resource set but disabled and the other without any resource but enabled.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix a spelling mistake in arch/arm/boot/dts/kirkwood-topkick.dts.
The manufacturer's name is Univer*s*al Scientific Industrial...
Compare with footer of page here:
http://www.usish.com/english/products_topkick1281p2.php
Signed-off-by: Paul Wassi <p.wassi@gmx.at>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch converts my orion5x ls-chl Linkstation device to device tree.
[gregory.clement@free-electrons.com: fix title, add back the commit log,
move the removal of the platform in an other patch]
Signed-off-by: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The SMSC9112 ethernet controller is connected to chip select 2
on the EBI2 bus on the APQ8060 Dragonboard. We set this up by
activating EBI2, creating a chipselect entry as a subnode, and then
putting the ethernet controller in a subnode of the chipselect.
After the chipselect is configured, the SMSC device will be
instantiated.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the external bus interface EBI2 to the MSM8660 device
tree, albeit with status = "disabled" so that devices actually
using EBI2 can turn it on if needed.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add pstore support for the nexus7. This was useful in debugging
a crash where the cpus were getting stuck with irqs off and
serial output wasn't reliably working.
Cc: Kees Cook <keescook@chromium.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Vinay Simha <vinaysimha@inforcecomputing.com>
Cc: Archit Taneja <architt@codeaurora.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add DSI and panel nodes to get graphics up and running
on the Nexus7.
This still depends on the panel driver being present
along with the rpmclk code.
Feedback would be greatly appreciated!
Cc: Archit Taneja <architt@codeaurora.org>
Cc: vinay simha <vinaysimha@inforcecomputing.com>
Cc: andy.gross@linaro.org
Cc: robdclark@gmail.com
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adds the core gpu, and dsi nodes for the apq8064 needed
to get graphics working on the nexus7 and other devices.
These apply on top of Archit's patch set that enables HDMI for IFC6410
Feedback would be greatly appreciated!
Cc: Archit Taneja <architt@codeaurora.org>
Cc: vinay simha <vinaysimha@inforcecomputing.com>
Cc: andy.gross@linaro.org
Cc: robdclark@gmail.com
Cc: linux-arm-msm@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add HDMI support on IFC6410. Populate the regulators required by HDMI-TX
and PHY. Establish the link between the MDP4 DTV encoder and HDMI. Create
a generic micro HDMI connector DT node. The msm drm driver doesn't parse
for HDMI connectors in DT, but it will do so later.
Cc: devicetree@vger.kernel.org
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
APQ8064 contains a MDP4 based display controller. It contains a HDMI, LVDS
and 2 DSI outputs.
Add display DT nodes for MDP4, HDMI TX and HDMI PHY. MDP4 based display
blocks have a flat device hierarchy.
Nodes for other outputs will be added later.
Cc: devicetree@vger.kernel.org
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This introduces the eMMC sdhci node and its pinctrl state
Signed-off-by: Bhushan Shah <bshah@kde.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add support for the Sierra Wireless MangOH Green board with the
Sierra Wireless WP8548 Module.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In order to support the Sierra Wireless WP8548 module based on the
Qualcomm MDM9615 SoC, add a dtsi file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Adds support for GMI on Tegra20 and Tegra30 and enables the GPU on Nyan
Chromebooks. It also enables sound support on various Toradex devices.
-----BEGIN PGP SIGNATURE-----
iQIwBAABCAAaBQJYLyczExx0cmVkaW5nQG52aWRpYS5jb20ACgkQ3SOs138+s6G3
WxAAos+oFvb2YFW0TNbJHCH/AW17U8kepXhmf8SEScRiiYP3sMgcN6kLK/pCvfBr
49FAHt/enDol3tw73nov0OOTyfXgcDEX/+i42irKwj0GSWeJHbaVqLpqP+ugrfg9
v0UGuycofbmvQyXWd8zF1yE7FtFwwExJHv+t7Rwu8y0Rwh55Q094P+ct5nRZbmpU
yUxw01xgguCAISaHVAp4h6l5NXi3m0dzYC2NUISO32wNYLGlV/u0vy8PLWYUEqHf
tcISM4sJwQbvl0P8kUvvvrQNRfD55pCXweprEeOzoesPZJOCrClBnRK3sCiXhANw
iVt6cpY9BN5xtbTrVNvtQZTKbqECnshRLyX450ZHwD+hIIVRI01W+aZB29WuO3GC
3J+82+TUZrt/BXAXlnpaNmMbzN9OKJs6eqOgs4CTjpFv/CCbnpQsEMOiWgFNoYfg
Lz3iz5xcKS9XJ8ImhIJvCLzTzvLuRsSRGcdAGp3BWp330qEZAe/MA2U4sT8dE24W
necF/FqJ3qLtVF1b5I6lOK3FPMfSNzQJHDgu469QXRxZKcyJoxuRyKXW0sP4zKp0
mZbuawOMLEIEvt8PCLSZN6MzgNsHXH3eA0sYfriXpdsUBD2/l1AO1GhkuD2MG9p9
24W8av2cpLNmVR7/wsarMX8429mUo1N7rSpHwsvtlTww2bg=
=w7VH
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.10-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.10-rc1
Adds support for GMI on Tegra20 and Tegra30 and enables the GPU on Nyan
Chromebooks. It also enables sound support on various Toradex devices.
* tag 'tegra-for-4.10-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: apalis-tk1: Drop leading 0 from unit-address
ARM: tegra: apalis/colibri t30: Integrate audio
ARM: tegra: nyan: Enable GPU node and related supply
ARM: tegra: Add Tegra30 GMI support
ARM: tegra: Add Tegra20 GMI support
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYLvYLAAoJEME3ZuaGi4PX7FYP/RUWX+IGk5xZg9xsi/VBN5wg
IDOseVLPTiz5VxgU1CvCMAxAbdshlPrrn6jgfmj0IRmF5g+9RfjpS6y3X+YIELUA
hD7altzN75JzY9rV4BhnHeFaRBK53gTeno+4O2hDarew6dRN4A2UtMTFpgGav9S/
T3vgIrsAXq7vrtnT9dePja0WISzl7l0JgzByTKEtu3egoy6wl20hrslGSJI+sWmt
Mu969g50RJsbrinzhv2qAYqN9AYuDSHUo8KVUJ2mg0ow9zkeJ/AeHlB4zuUK8dUf
dPW9tVtQDrcl6sA4wqG4Tno2JjJHqnJNBvE3KOnxqWd/ed7Mz7Pddrc4AaqB5o5l
GDZxzAx2xb+rX+dWwURVXAtS54RUnD8e1S7Jp8X2+eCL8OUKXvfO6p/XA45/8V/S
9VJNP/gUL594Zyyj5LuAhqyOfbtcrW2VaZntts68NVjhtYfRcHF8UrxGtj6RxZnH
mOZC5HNBNIxrpzI+YfSiTCk0ec1CRFtbqC0sMIJoC2DJ+IGint2UPz8VOFMJrZlw
0zVXCr0NKHCgvJqPIV24udyzPq79REfdsElZQYyl6GDYGXAqTJLR+OP6/Sc/MNv5
c1uObjQLd/Yi7e9BhqHF60t9s+y3whmqnvOibTEsnRX145VaPBnfwomc1XU9PVIn
YdK2ml1FgIGdZNZ5dPxy
=lyeE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch with DT changes for v4.10.
Fix invalid GIC interrupt flags - type IRQ_TYPE_NONE is not allowed for GIC
interrupts. Although this was working but with error messages like:
genirq: Setting trigger mode 0 for irq 16 failed
Use level high interrupt instead of type none. The choice of level high was
rather an arbitrary decision hoping it will work on each platform. Tests shown
no issues so far.
* tag 'samsung-dt-gic-flags-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5440
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5260
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos5
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos4
ARM: dts: exynos: Use human-friendly symbols for interrupt properties in exynos3250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5440
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5260
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5410/exynos542x
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos5
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos3250
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4x12
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4210
ARM: dts: exynos: Fix invalid GIC interrupt flags in exynos4
Signed-off-by: Olof Johansson <olof@lixom.net>
- A series of patches to configure tps65217 PMIC interrupts for
power button, charger and usb and use them on am335x
- Configure EEPROM, LEDs and USR1 button for omap5 boards
- Add tscadc DMA properites for am33xx and am4372
- Configure baltos-ir5221 both musb channels to host mode
- Configure internal and external RTC clocks for am335x boards
- Don't reset gpio3 block on baltos
- Remove pinmux for dra72-evm for erratum i869, fix the regulators
and seprate out tps65917 support
- Add dra718-evm support
- Add minimal droid 4 xt894 support
-----BEGIN PGP SIGNATURE-----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=GYpd
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.10 merge window:
- A series of patches to configure tps65217 PMIC interrupts for
power button, charger and usb and use them on am335x
- Configure EEPROM, LEDs and USR1 button for omap5 boards
- Add tscadc DMA properites for am33xx and am4372
- Configure baltos-ir5221 both musb channels to host mode
- Configure internal and external RTC clocks for am335x boards
- Don't reset gpio3 block on baltos
- Remove pinmux for dra72-evm for erratum i869, fix the regulators
and seprate out tps65917 support
- Add dra718-evm support
- Add minimal droid 4 xt894 support
* tag 'omap-for-v4.10/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (22 commits)
ARM: dts: Add minimal support for motorola droid 4 xt894
ARM: dts: Add support for dra718-evm
ARM: dts: dra72: Add separate dtsi for tps65917
ARM: dts: dra72-evm: Fix modelling of regulators
ARM: dts: dra72-evm: Remove pinmux configurations for erratum i869
ARM: dts: am335x-baltos: don't reset gpio3 block
ARM: dts: AM335X-evmsk: Add the internal and external clock nodes for rtc
ARM: dts: AM335X-evm: Add the internal and external clock nodes for rtc
ARM: dts: AM335X-bone-common: Add the internal and external clock nodes for rtc
ARM: dts: am335x-baltos-ir5221: use both musb channels in host mode
ARM: dts: am4372: add DMA properties for tscadc
ARM: dts: am33xx: add DMA properties for tscadc
ARM: dts: omap5 uevm: add USR1 button
ARM: dts: omap5 uevm: add LEDs
ARM: dts: omap5 uevm: add EEPROM
ARM: dts: am335x: Add the power button interrupt
ARM: dts: am335x: Add the charger interrupt
dt-bindings: mfd: Provide human readable defines for TPS65217 interrupts
ARM: dts: am335x: Support the PMIC interrupt
ARM: dts: tps65217: Add the power button device
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Recently added audio block of Exynos5410 missed global fixup of GIC
interrupt flags. Interrupt of type IRQ_TYPE_NONE is not allowed for GIC
interrupts so use level high.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
- New boards support: i.MX6SX UDOO Neo, Boundary Devices Nitrogen6_SOM2,
Engicam i.CoreM6, Grinn i.MX6UL liteSOM/liteBoard, Toradex Colibri
iMX6 module, i.MX6ULL and EVK board.
- Remove skeleton.dtsi inclusion from all i.MX SoC dts files, as it's
been deprecated, since commit 9c0da3cc61 ("ARM: dts: explicitly
mark skeleton.dtsi as deprecated").
- Misc device addition and enabling: OCOTP for Vybrid, MMDC for i.MX6QP,
TMU for LS1021A, FEC for imx6qdl-icore, DMA for Vybrid DSPI.
- A few cleanups: use hyphens for node names, fix white spaces, move
imx-weim parameters into SoC dtsi, replace gpio-key,wakeup with
wakeup-source, remove pwm-leds from imx6q-apalis-ixora, remove I2C3
from vf610-zii-dev-rev-b.
- Other small random changes: calibrate USB PHY for b650v3 board,
update TX D_CAL for USBPHY, use enable-gpios for backlight on
imx6qdl-apalis, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKrEtAAoJEFBXWFqHsHzOpnIH/j4Ot/09VQR7IddDY4PkOX53
7zsYkzVLvUIlAkylICfyjoz8XeiyLl9rM4jg8ubnWBOiKDl1lMxeUfvAmAeX+D5U
9bgLgNxok7ugUZZKNt6h3+4Q6eAsXBltXBwIMiFEVsHa6sDFro2S4xq74DytEpZR
Czg6inH9GHix7urlNn5YWvxHDCJMRx3AUQtYlUCb7dd3MrNegvddE3osF49KCdzA
yKwdN+BdAKL0avWS9BurmXYCVl7OcReIuCIEKA9235V7o5HnBPHbDrxBUO9shqOp
KcIpTM6rUMRNdzs7CcvkOco2nDkHnOt0u5v4ON29GVq8w2jX+lmbVZCSkCVk44I=
=+GDb
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree updates for 4.10:
- New boards support: i.MX6SX UDOO Neo, Boundary Devices Nitrogen6_SOM2,
Engicam i.CoreM6, Grinn i.MX6UL liteSOM/liteBoard, Toradex Colibri
iMX6 module, i.MX6ULL and EVK board.
- Remove skeleton.dtsi inclusion from all i.MX SoC dts files, as it's
been deprecated, since commit 9c0da3cc61 ("ARM: dts: explicitly
mark skeleton.dtsi as deprecated").
- Misc device addition and enabling: OCOTP for Vybrid, MMDC for i.MX6QP,
TMU for LS1021A, FEC for imx6qdl-icore, DMA for Vybrid DSPI.
- A few cleanups: use hyphens for node names, fix white spaces, move
imx-weim parameters into SoC dtsi, replace gpio-key,wakeup with
wakeup-source, remove pwm-leds from imx6q-apalis-ixora, remove I2C3
from vf610-zii-dev-rev-b.
- Other small random changes: calibrate USB PHY for b650v3 board,
update TX D_CAL for USBPHY, use enable-gpios for backlight on
imx6qdl-apalis, etc.
* tag 'imx-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (38 commits)
ARM: dts: imx6ull: add imx6ull support
ARM: dts: imx6q: replace gpio-key,wakeup with wakeup-source for Utilite Pro
ARM: dts: vfxxx: Enable DMA for DSPI2 and DSPI3
ARM: dts: imx: Remove skeleton.dtsi
ARM: dts: imx6q-utilite-pro: i2c1 is muxed
ARM: dts: add new compatible string for i.MX6QP mmdc
ARM: dts: imx6sx-udoo: Add board specific compatible strings
ARM: dts: mx5: Add new M53EVK manufacturer compat
ARM: dts: mxs: Add new M28EVK manufacturer compat
ARM: dts: imx6ul-14x14-evk: update TX D_CAL for USBPHY
ARM: dts: imx6sx-sdb: update TX D_CAL for USBPHY
ARM: dts: imx6: Add imx-weim parameters to dtsi's
ARM: dts: imx: Fix "ERROR: code indent should use tabs where possible"
ARM: dts: imx6qdl-nitrogen6_max: use hyphens for nodes name
ARM: dts: imx6qdl-nit6xlite: use hyphens for nodes name
ARM: dts: imx6qdl-nitrogen6x: use hyphens for nodes name
ARM: dts: imx6qdl-sabrelite: use hyphens for nodes name
ARM: dts: imx: add Boundary Devices Nitrogen6_SOM2 support
ARM: dts: imx6qdl-icore: Add FEC support
ARM: dts: imx6q: Add Engicam i.CoreM6 DualLite/Solo initial support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- A series from Vladimir to fix broken i.MX31 DT clock initialization.
As i.MX31 DT support is still not quite complete, the changes are
tested on qemu kzm target and mx31lite board with simple written DTS
files.
- A fix for CompuLab's sbc-fx6 baseboard to remove wrong fec pinctrl
setting.
- A DTS correction for i.MX6QP to reflect the change that the gate of
LDB clock has been moved before the divider.
- An imx7d-pinfunc fix for UART pinmux defines
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKoTwAAoJEFBXWFqHsHzOGyMH/03fFizPHl+LQYilR8hKbFLg
amAhmqVEM0gRv/yvBwi/I0FXUyoBY4rhhAzvjy+1eF23wlipXt+2FozlXLW3jy2w
YP1bTnSy3qN5+eZakfeARFDh7Q1ab/19ZBJYFyQaRB2yY3CRDz3xeY5mOeVHdnUb
jI1+GpDAr37acGlGVOrsYJlpNlzX8HjAfRhPvlEqMH1Xp/1O5EgkzHyICKR9ysaB
f7fDTAhVsxivdCF/XU6TpyOUtWshu0v4ji+JtvRkz0p+9gHgWGKzu9ixQTr1FFxZ
YHPnxpDf4jtygLtrrzT4qBww/84PemAfQ3Rhpl1aG9331VB962UZ3R+JDoSSwnE=
=Xqw0
-----END PGP SIGNATURE-----
Merge tag 'imx-fix-nc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/fixes-non-critical
i.MX non-critical fixes for 4.10:
- A series from Vladimir to fix broken i.MX31 DT clock initialization.
As i.MX31 DT support is still not quite complete, the changes are
tested on qemu kzm target and mx31lite board with simple written DTS
files.
- A fix for CompuLab's sbc-fx6 baseboard to remove wrong fec pinctrl
setting.
- A DTS correction for i.MX6QP to reflect the change that the gate of
LDB clock has been moved before the divider.
- An imx7d-pinfunc fix for UART pinmux defines
* tag 'imx-fix-nc-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6q-cm-fx6: fix fec pinctrl
ARM: dts: imx7d-pinfunc: fix UART pinmux defines
ARM: dts: imx6qp: correct LDB clock inputs
ARM: clk: imx31: properly init clocks for machines with DT
clk: imx31: fix rewritten input argument of mx31_clocks_init()
ARM: dts: imx31: move CCM device node to AIPS2 bus devices
ARM: dts: imx31: fix clock control module interrupts description
Signed-off-by: Olof Johansson <olof@lixom.net>
us to use generic parser later on. Note that the driver supports
handling the legacy binding also with no #pinctrl-cells so these
changes can be queued separately from the driver changes.
-----BEGIN PGP SIGNATURE-----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=qXyV
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.10/pinctrl-cells-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Add #pinctrl-cells for pinctrl-single using dts files. This allows
us to use generic parser later on. Note that the driver supports
handling the legacy binding also with no #pinctrl-cells so these
changes can be queued separately from the driver changes.
* tag 'omap-for-v4.10/pinctrl-cells-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add #pinctrl-cells for pinctrl-single instances
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the cpus node to the Integrator/AP device tree so
that we have a proper placeholder to put in the DT-defined
operating points for the generic DT/OPP cpufreq driver,
along with the proper operating points.
The old Integrator cpufreq driver would resolve the max
frequency to 71MHz, and the min frequency to 12 MHz, but
the clock driver can actually handle any frequency inbetween
so I picked a few select frequencies as OPPs. The cpufreq
framework doesn't seem to deal with sliding frequency scales,
only fixed points so 7 OPPs is better than 2 atleast.
We define a CPU node since this is required for cpufreq-dt,
however we do not define any compatible string for the CPU
since this architecture has pluggable CPU modules and we
do not know which one will be used. If necessary, the CPU
compatible can be filled in by the boot loader, but for
just cpufreq-dt it is not required.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds the cpus node to the Integrator/CP device tree so
that we have a proper placeholder to put in the DT-defined
operating points for the generic DT/OPP cpufreq driver,
along with two working operating points.
I have only put in 48 and 50 MHz because going to e.g. 36
MHz hangs the system when CLCD graphics are active.
Presumably the memory bus gets to slow to feed the display
and the systems hangs for this reason. The ideal solution
would be for the display controller to put constraints on
the memory bus frequency, but that need to be a separate
longer-term project.
We define a CPU node since this is required for cpufreq-dt,
however we do not define any compatible string for the CPU
since this architecture has pluggable CPU modules and we
do not know which one will be used. If necessary, the CPU
compatible can be filled in by the boot loader, but for
just cpufreq-dt it is not required.
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the relevant data taken from the PXA27x Electrical, Mechanical, and
Thermal Specfication. This will be input data for cpufreq-dt driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add the relevant data taken from the PXA 25x Electrical, Mechanical, and
Thermal Specfication. This will be input data for cpufreq-dt driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Since gpio-pxa was redesigned to differenciate gpio0, gpio1 and the
gpio-mux interrupt as in the hardware IP, the device-tree description
should be amended so that interrupts from gpio0 and gpio1 can be mapped
to consumers.
This is especially true on lubbock and mainstone devices where gpio0 is
multiplexed on pxa_cplds for ethernet, sa1111, usb udc, and other
devices.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This file describes pxa25x SoCs. Not all devices are listed yet, only
the subset which was already tested with a lubbock board.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The TPIC2810 is available on both the AM571x and the AM572x IDKs and
is attached to I2C1. Output is attached to the I/O header and 10 LEDs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SN65HVS882 is available on both the AM572x and AM571x IDKs and is
attached to SPI1. Input is attached to the I/O header. The load trigger
is attached to GPIO3_19 on the AM572x IDK.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The TPIC2810 is available on the AM437x IDK and is attached to I2C1.
Output is attached to the I/O header and 10 LEDs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SN65HVS882 is available on the AM437x IDK and is attached to SPI1.
Input is attached to the I/O header.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
7 of the 8 ADC inputs on the am335x are connected to the Industrial I/O
header, add this here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LEDs tied to the Industrial I/O output pins are meant for providing
status feed-back and are not the primary use for the pins. Disable
this use by default. Also unify the LED naming across IDK platforms.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SN65HVS882 is available on the AM335x-ICEv2 and is attached to SPI0.
Input is attached to the I/O header.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Odroid-X, -X2, -XU3 and -XU4 have SOC-ADC routed to an external connector.
Enable the ADC for use as iio-device.
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This is not needed as the gadget now fully supports DMA and it can
autodetect it. This was initially added because gadget DMA mode was only
partially implemented so could not be automatically enabled.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
- Add clocks for auxadc on mt8173-evb
- Add nodes needed by clock controller for mt2701
- Use clocks from the clock controller for the uart of mt2701
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJYJdcrAAoJELQ5Ylss8dNDoJcP/2q1LuStbojWMWxFKexQBCIk
8VEPzY8fyEckshbmgnz36qqp2MnecTLjb1ETesFIEGZWbEBnoAJC9hyIg6fFVZQi
mFZC8/0I7uvaFZHa+a3fQZb3tCmLMcWbAaGvA0p28kNRKnRhTMVHhLa7Z0WmMrG+
lQLlBBTP/xHErOakFJagkFIWYmmmMReS7x+X/tnVPienxkwODjpLYJQLL1wVmoqV
lpSj/nSRRDg8CeeG8/x+Odtr77L56glDMwwieXVpBe2sd+CpRk3QSTTcuYLkUp46
JBBKrr7TLLD6KEw6FgPjvjWDR3TH7S2wkbZVJN4B+8tmdEhpQhnle2MpJ6TYLKQb
ENwZ9JP70UD8o6mWb5e/g9R82WxUq1KDpdlU71OeBsnqfJRn1sge8bsO6+qs4+6Z
JapDW+Zwsewp9VZS12k4VdsCsYR0MZgX6XXj/NOOseJOMUXBFAoHj7vaC5Gj0UIT
VFKndrzWjIaVbaLHA/2KyVvOpJsEVTwSURyEko6XnTRLg+E85SSx+r6Bp3rlSlCV
Javet8M9YTLhPa1IeFMvf/1V4C4poX5tE4tvCiSZC1Wvxto5FSEgeGarq59Pgyi3
UWnxao8FHBHi3NU8khTI+rnIYtw5WxkEpqU5UUTYMUwsQ3x83VnU0WzpCSKQSNdD
Od24wmc/rrNKeU098abr
=wFjD
-----END PGP SIGNATURE-----
Merge tag 'v4.9-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
- Add bindings for mtk-scpsys for mt2701
- Add clocks for auxadc on mt8173-evb
- Add nodes needed by clock controller for mt2701
- Use clocks from the clock controller for the uart of mt2701
* tag 'v4.9-next-dts' of https://github.com/mbgg/linux-mediatek:
arm: dts: mt2701: Use real clock for UARTs
arm: dts: mt2701: Add clock controller device nodes
arm64: dts: mt8173: Fix auxadc node
soc: mediatek: Add MT2701 power dt-bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
inclusion, missing unit names for memory nodes, various frequency
optimizations allowing for better performance on rk3066, the usage of
pin constants to bridge between the two numbering schemes used (gpio
controllers using 0-31 and pins being labeled A0-A7,..., D0-D7)
and UHS/HS modes for the mmc controllers on the popmetal board.
Two new boards, the PX3-based evaluation board, with the PX3 being an
industrial variant of the rk3188 soc and the Rikomagic MK808 board
based around the rk3066 are also added.
-----BEGIN PGP SIGNATURE-----
iQEtBAABCAAXBQJYJzNfEBxoZWlrb0BzbnRlY2guZGUACgkQ86Z5yZzRHYGsQQf/
WWYA4/oR4pT8HMns5coctc2zOyNU8KYmaeRl7TViUna+HA6/m2SGMqomTFV2AK0v
Ha3M6A35dDUGJNmAbEB5oolGOwHh82gZKYxYIQiNX+zCxeb5JxKCXWSqAjC9Ndwu
h600H1K/Qb26OzaVE/ICtlveduN+9BWrlzNseHsm99Z93FNsRLN0Z8s2Mn3jra6P
2Pf1sJkOPuh47i/Y/gTDVcFSf6Srb4SM/26fiZjrRa8LaaO/0I2Ku34ne9FygGzi
0GBHWh2SILM297MZMcrCDoJvTTqLT05tUrX1PDGmdunqP8vnsOAgvL9291G8d4sw
PbYE3onlyoxHmeOSffAe5g==
=AXPK
-----END PGP SIGNATURE-----
Merge tag 'v4.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
32bit devicetree changes for Rockchip including removal of skeleton.dtsi
inclusion, missing unit names for memory nodes, various frequency
optimizations allowing for better performance on rk3066, the usage of
pin constants to bridge between the two numbering schemes used (gpio
controllers using 0-31 and pins being labeled A0-A7,..., D0-D7)
and UHS/HS modes for the mmc controllers on the popmetal board.
Two new boards, the PX3-based evaluation board, with the PX3 being an
industrial variant of the rk3188 soc and the Rikomagic MK808 board
based around the rk3066 are also added.
* tag 'v4.10-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (21 commits)
ARM: dts: rockchip: replace to "max-frequency" instead of "clock-freq-min-max"
ARM: dts: rockchip: Set sdmmc frequency at boot time for rk3066a
ARM: dts: rockchip: use pin constants to describe gpios on Popmetal-RK3288
include: dt-bindings: Add GPIO pin index definition for rockchip pinctrl
ARM: dts: rockchip: Add rk3066 MK808 board
devicetree: Add vendor prefix for Rikomagic
ARM: dts: rockchip: initialize rk3066 PLL clock rate
clk: rockchip: Add binding ids for cpu and peri clocks on rk3066
ARM: dts: rockchip: enable HS200/DDR52 mode for emmc on rk3288-popmetal
ARM: dts: rockchip: Support UHS mode for SD card on PopMetal-RK3288 board
ARM: dts: rockchip: remove always-on and boot-on from vcc_sd for px3-evb
ARM: dts: rockchip: update compatible strings for Rockchip efuse
ARM: dts: rockchip: add rockchip PX3 Evaluation board
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3xxx boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3288 boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk322x boards
ARM: dts: rockchip: Add missing unit name to memory nodes in rk3036 boards
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk3xxx.dtsi
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk3288.dtsi
ARM: dts: rockchip: Remove skeleton.dtsi inclusion in rk322x.dtsi
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add specific compatible strings for variants of Cyclone5 boards
- Add QSPI node on Arria10
- Enable QSPI on Arria5 and Arria10 devkit, and Cyclone5 SoCKit
- Add NAND controller node on Cyclone5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=clFU
-----END PGP SIGNATURE-----
Merge tag 'socfpga_dts_for_v4.10_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS update for v4.10, part 2
- Add specific compatible strings for variants of Cyclone5 boards
- Add QSPI node on Arria10
- Enable QSPI on Arria5 and Arria10 devkit, and Cyclone5 SoCKit
- Add NAND controller node on Cyclone5
* tag 'socfpga_dts_for_v4.10_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: add nand controller nodes
ARM: dts: socfpga: Enable QSPI on the Arria5 devkit
ARM: dts: socfpga: Enable QSPI on the Cyclone5 sockit
ARM: dts: socfpga: Enable QSPI in Arria10 devkit
ARM: dts: socfpga: Add QSPI node for the Arria10
ARM: dts: socfpga: enable qspi on the Cyclone5 devkit
ARM: dts: socfpga: add specific compatible strings for boards
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add TOPEET itop core and Elite boards, based on Exynos4412.
2. Remove the Exynos4415 DTSI. We did not have any mainlined boards
using it. I am also not aware of any popular out-of-tree boards using it.
3. Add Snoop Control Unit node for Exynos4.
4. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qzwE
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.10:
1. Add TOPEET itop core and Elite boards, based on Exynos4412.
2. Remove the Exynos4415 DTSI. We did not have any mainlined boards
using it. I am also not aware of any popular out-of-tree boards using it.
3. Add Snoop Control Unit node for Exynos4.
4. Minor cleanups.
* tag 'samsung-dt-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add SCU device node to exynos4.dtsi
ARM: dts: exynos: Remove exynos4415.dtsi
ARM: dts: exynos: Document eMMC/SD/SDIO devices in Snow and Peach boards
ARM: dts: exynos: Add TOPEET itop elite based board
ARM: dts: exynos: Add TOPEET itop core board SCP package version
ARM: dts: exynos: Add entries for sound support on Odroid-XU board
ARM: dts: exynos: Remove "simple-bus" compatible from fimc-is node
Signed-off-by: Olof Johansson <olof@lixom.net>
This includes a single functional change:
* set default parent clock for PWM1 & PWM2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=9l30
-----END PGP SIGNATURE-----
Merge tag 'lpc32xx-dt-v4.10' of https://github.com/sylemieux/linux-lpc32xx into next/dt
NXP LPC32xx ARM SoC device tree updates for v4.10
This includes a single functional change:
* set default parent clock for PWM1 & PWM2.
* tag 'lpc32xx-dt-v4.10' of https://github.com/sylemieux/linux-lpc32xx:
ARM: dts: lpc32xx: set default parent clock for pwm1 & pwm2
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add OPP tables to support generic cpufreq driver
- Use more clocks/resets properties
- Misc fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DdcH
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into next/dt
UniPhier ARM SoC DT updates for v4.10
- Add OPP tables to support generic cpufreq driver
- Use more clocks/resets properties
- Misc fixes and cleanups
* tag 'uniphier-dt-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: make compatible of syscon nodes SoC-specific
ARM: dts: uniphier: add clocks/resets to EHCI nodes of sLD3 SoC
ARM: dts: uniphier: remove redundant serial fifo-size properties
ARM: dts: uniphier: make 32bit SoC DTSI linear
ARM: dts: uniphier: add CPU clocks and OPP table for PXs2 SoC
ARM: dts: uniphier: add CPU clocks and OPP table for Pro5 SoC
ARM: dts: uniphier: increase register region size of sysctrl node
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJYFQwAAAoJEHm+PkMAQRiGr8YH/0urDFZm/RFu752rSawF7iVM
nx9Ck03YkRiMRZfdzPARbHJts7lhLG1rvsT50VQNMK1sVv0BXcrnJnDu49xV+dLj
DqXWvYGtdTCpAd34Am37pX/rrRl11vdJgS2VgprmbytkM8FD0xEe+aDKxnnmuALo
bggYDhMrJik3/UXG0zVfefKZJFLNAJiZv9AgWgkCR+bo861bu3UFn47tN1jGXOOl
QyFl5t7ggesojA5Q1U9hTrk1gS9Ia9it3Elyzfqb66lUdyf001I1nbUA/hNYyDXD
HU9dj3agvVXjvnDjyDR4/k86FA+EEEwSgk5CBTCVe30dLKnojFyb7FWZg72utg4=
=CHER
-----END PGP SIGNATURE-----
Merge tag 'v4.9-rc3' into next/dt
Linux 4.9-rc3
* tag 'v4.9-rc3': (292 commits)
Linux 4.9-rc3
x86/smpboot: Init apic mapping before usage
ACPICA: Dispatcher: Fix interpreter locking around acpi_ev_initialize_region()
ACPICA: Dispatcher: Fix an unbalanced lock exit path in acpi_ds_auto_serialize_method()
ACPICA: Dispatcher: Fix order issue of method termination
ARC: module: print pretty section names
ARC: module: elide loop to save reference to .eh_frame
ARC: mm: retire ARC_DBG_TLB_MISS_COUNT...
ARC: build: retire old toggles
ARC: boot log: refactor cpu name/release printing
ARC: boot log: remove awkward space comma from MMU line
ARC: boot log: don't assume SWAPE instruction support
ARC: boot log: refactor printing abt features not captured in BCRs
ARCv2: boot log: print IOC exists as well as enabled status
ubifs: Fix regression in ubifs_readdir()
ubi: fastmap: Fix add_vol() return value test in ubi_attach_fastmap()
MAINTAINERS: Add entry for genwqe driver
VMCI: Doorbell create and destroy fixes
GenWQE: Fix bad page access during abort of resource allocation
vme: vme_get_size potentially returning incorrect value on failure
...
Clean-Ups and Corrections:
* Removed Z clock from r8a7794 SoC; it is not present in hardware
* Use generic pinctrl properties in SDHI nodes in gose board
* Correct W=1 dtc warnings on r8a7794 SoC
* Correct DU reg property on r8a7779 SoC
* Correct SCIFB reg properties to cover all registers
Enhancements:
* Configure pinmuxing for the DU0 input clock on the Marzen board
* Enable VIN 0 - 2 on r8a7793 SoC
* Enable HDMI input on Koelsch and Lager boards
* Enable SDHI1 on rskrza1 board
* Add MMCIF nodes to r7s72100 SoC
* Add MSIOF clocks to r8a7792 SoC
* Enable UHS for SDHI 0 & 1 on koelsch and alt boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Tkdc
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.10
Clean-Ups and Corrections:
* Removed Z clock from r8a7794 SoC; it is not present in hardware
* Use generic pinctrl properties in SDHI nodes in gose board
* Correct W=1 dtc warnings on r8a7794 SoC
* Correct DU reg property on r8a7779 SoC
* Correct SCIFB reg properties to cover all registers
Enhancements:
* Configure pinmuxing for the DU0 input clock on the Marzen board
* Enable VIN 0 - 2 on r8a7793 SoC
* Enable HDMI input on Koelsch and Lager boards
* Enable SDHI1 on rskrza1 board
* Add MMCIF nodes to r7s72100 SoC
* Add MSIOF clocks to r8a7792 SoC
* Enable UHS for SDHI 0 & 1 on koelsch and alt boards
* tag 'renesas-dt-for-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (29 commits)
ARM: dts: r8a7794: remove Z clock
ARM: dts: r8a7779: marzen: Configure pinmuxing for the DU0 input clock
ARM: dts: sh73a0: Remove skeleton.dtsi inclusion
ARM: dts: r8a7740: Remove skeleton.dtsi inclusion
ARM: dts: r8a7779: Remove skeleton.dtsi inclusion
ARM: dts: r8a7778: Remove skeleton.dtsi inclusion
ARM: dts: emev2: Remove skeleton.dtsi inclusion
ARM: dts: r8a7779: Fix DU reg property
ARM: dts: r8a7793: Enable VIN0-VIN2
ARM: dts: koelsch: add HDMI input
ARM: dts: lager: Add entries for VIN HDMI input support
ARM: dts: rskrza1: add sdhi1 DT support
ARM: dts: r7s72100: add sdhi to device tree
ARM: dts: r8a7794: Fix W=1 dtc warnings
ARM: dts: gose: use generic pinctrl properties in SDHI nodes
ARM: dts: r7s72100: add sdhi clock to device tree
ARM: dts: r7s72100: add mmcif to device tree
ARM: dts: r8a7792: add MSIOF support
ARM: dts: r8a7792: add MSIOF clocks
ARM: dts: wheat: add DU support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add blue-and-red-wiring -property to LCDC node. Also adds comments on
how to get support 24 bit RGB mode. After this patch am335x-boneblack
support RGB565, BGR888, and XBGR8888 color formats. See details in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt.
The BBB has straight color wiring from am335x to tda19988, however the
tda19988 can be configured to cross the blue and red wires. The
comments show how to do that with video-ports property of tda19988
node and how to tell LCDC that blue and red wires are crossed, with
blue-and-red-wiring LCDC node property. This changes supported color
formats from 16 bit RGB and 24 bit BGR to 16 bit BGR and 24 bit RGB.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A fix to reintroduce missing pinmux options that turned out not to be
optional.
-----BEGIN PGP SIGNATURE-----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=WBs5
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Allwinner fixes for 4.9
A fix to reintroduce missing pinmux options that turned out not to be
optional.
* tag 'sunxi-fixes-for-4.9' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i: fix the pinmux for UART1
Signed-off-by: Olof Johansson <olof@lixom.net>
It fixes a boot failure on imx53-qsb board with a DA9053 PMIC, which is
caused by the regulator core change, commit fa93fd4ecc ("regulator:
core: Ensure we are at least in bounds for our constraints").
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYKnQ1AAoJEFBXWFqHsHzOyEYH/0F1TKtmJwLeDBKBinmeG0wx
IX/0mXCV0E72T7W6PuifofG7H9jax9UY8qGyDl9+h/dMBQCaKPfXDo6wg5FoXaBe
UAQVHbRbEuazI2xW0UWeiywt6soGBe1/iNpt+OXXfmJY77vS5nuGfFCLGey6+uTe
WeGi3J6g2Oxa65FndvfTm5dNj6vCa3VHs5UKQKCId3KoTjuLZu4EUrN81e47tkmJ
pmzaGBfAUyvACfwkITzc6rAbBp29FtxMK52ieuh+w4L3DWa3kpCabHPMIAeP8C9P
GQ80PTyfs/F163yYM6dWRipwhz/XJhjtT8SWBG/hnYBJDEHOua4uqW3YcoNdm7E=
=xunY
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.9, 2nd round:
It fixes a boot failure on imx53-qsb board with a DA9053 PMIC, which is
caused by the regulator core change, commit fa93fd4ecc ("regulator:
core: Ensure we are at least in bounds for our constraints").
* tag 'imx-fixes-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx53-qsb: Fix regulator constraints
Signed-off-by: Olof Johansson <olof@lixom.net>
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
-----BEGIN PGP SIGNATURE-----
iQIuBAABCAAYBQJYKlYvERx0b255QGF0b21pZGUuY29tAAoJEBvUPslcq6VzT50Q
AJEsYX1dYwMyVeditzSWb65ajT53uhxPw51vIfA/bV3FUsMTaD5aZ9fsxYMt/3Eo
ayEzDFM74FM9nMGB4gXW4wryta4r5NT/lBg6vvwJfivVjTUkhQUKmH6C94dg3t2d
bHr9isM7ONJ5wxx02olg9vHyNXXgWEwPLhWKtxZKanKpoxKJajSA5dJuZR9T39X5
ZuhPFFmpMEh+IsnqYs4C1+215cFkRf21aEhMqwKRySTcHf35zitPfiuYF4Gft6Vb
Cor9JXlZGUN+dfhG48qcn+1NBEgha5r7JT2u7w+dPCXKvEn6OmpyAziUT3CYHMAc
IGeZLmBznhSZhJUvYjBmiy88YLORpWvPuGCE19AKJoi+VOGv8bSc2bnp+JCw+Ven
DB0GDWJgI2FVPNrRrLRW+dOdKwH/R8b9vE3ZtVHK8x7vowViDoGyFpndv30sL0HA
ssRvC24wAyRAcpXtAqQrFc2I8BMLzVsLzHLHriR9EnhMAspk4IJV5zkFv52ZtlxO
N6NabaD7se2ww7q3MSGuIe3+u9u3KcfKf1dsaq/E8cWFxvcJ07xnCCCYJ8DlGmZh
mS+Fkbof7NO0gbSiapzgjVtb+sfrkKqYTiIMldTzIGzmEcpK6SKXC6mAcrFAPojK
ecBq9BrLuAte4u6W1ohQoAW6rwjfz6yrAqIdzhzufGsN
=LgIW
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.9-rc cycle. Except for the omap3 fix for the SoC
features printed, all these are quite trivial and tiny. The omap5 jack
detection and gpadc patches are not strictly fixes, but I wanted to get
binding document typo fixed before it pops up on other boards. The
gpadc one liner was in the same series and I applied and pushed it out
already before noticing it could have waited. The list of changes is:
- Fix omap3 SoC features printed
- Make sure OMAP_INTERCONNECT is selected for am43xx only configurations
- Add missing memory node for torpedo
- Initialize uart4_mask properly to avoid writing garbage to PRM registers
- Fix NULL pointer dereference for omap4 volt_data
- Add alias for omap5 gpadc needed by iio drivers
- Enable omap5 jack headset jack detection and fix it's binding typo
- Add missing memory node for logicpd-som-lv
- Fix wrong SMPS6 voltage for VDD-DDR3 for omap5
* tag 'omap-for-v4.9/fixes-for-rc-cycle' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5: board-common: fix wrong SMPS6 (VDD-DDR3) voltage
ARM: omap3: Add missing memory node in SOM-LV
ASoC: omap-abe-twl6040: fix typo in bindings documentation
dts: omap5: board-common: enable twl6040 headset jack detection
dts: omap5: board-common: add phandle to reference Palmas gpadc
ARM: OMAP2+: avoid NULL pointer dereference
ARM: OMAP2+: PRM: initialize en_uart4_mask and grpsel_uart4_mask
ARM: dts: omap3: Fix memory node in Torpedo board
ARM: AM43XX: Select OMAP_INTERCONNECT in Kconfig
ARM: OMAP3: Fix formatting of features printed
Signed-off-by: Olof Johansson <olof@lixom.net>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds the GPIO names for the Raspberry Pi Zero. The GPIO lines
of the RPi Zero are almost identical to the Model A+ except:
* GPIO 35, 38, 40 and 45 are not connected
* Status LED is active low
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are some differences between the schematics and the official firmware
DTS [1]. So based on these additional information the following has been
changed:
* use consistent "CAM_GPIO1" for camera LED
* use consistent "CAM_GPIO0" for camera shutdown
* add "USB_LIMIT" for USB current limit (0=600mA, 1=1200mA)
[1] - https://github.com/raspberrypi/firmware/blob/master/extra/dt-blob.dts
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This enables the GPIO-b support for Broadcom NSP SoC
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's BCM4709A0 based device with 16 MiB flash, 128 MiB of RAM and two
PCIe based on-PCB BCM4360 chipsets.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The M0 processor handles interrupts for the always-on CRMU GPIO
controller. Setting the CRMU GPIO driver with the mailbox controller as
the interrupt parent allows the mailbox controller to forward interrupts
from the M0 to the GPIO driver for processing.
Reviewed-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Tested-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Reviewed-by: Vikram Prakash <vikram.prakash@broadcom.com>
Reviewed-by: Shreesha Rajashekar <shreesha.rajashekar@broadcom.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathan.richardson@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
RK1108 EVB is designed by Rockchip for CVR field.
This patch add basic support for it, which can boot with
initramfs into shell.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
RK1108 is embedded with an ARM Cortex-A7 single core and a DSP core.
It is designed for varies application scenario such as car DVR, sports
DV, secure camera and UAV camera.
This patch add basic support for it with DMAC / UART / CRU / pinctrl / MMC
enabled.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Tested-by: Jacob Chen <jacob2.chen@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Drop the space before/after '<' and '>'; and
separate the entries to be a bit more readable.
Reported-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: arm-soc
Series-cc: julia@ni.com
The patch removes these warnings reported by dtc 1.4:
Warning (unit_address_vs_reg): Node /pmu has a reg or ranges property,
but no unit name
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name,
but no reg property
Warning (unit_address_vs_reg): Node /memory has a reg or ranges
property, but no unit name
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Julia Cartwright <julia@ni.com>
Series-to: arm-soc
Based on
"ARM: dts: explicitly mark skeleton.dtsi as deprecated"
(sha1: 9c0da3cc61)
skeleton.dtsi is deprecated.
Move address and size-cells directly to zynq-7000.dtsi.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Julia Cartwright <julia@ni.com>
Let's add minimal support for droid 4 with MMC and WLAN working.
It can be booted with appended dtb using kexec to a state where
MMC and WLAN work with currently no support for it's PMIC or
display.
Note that we are currently using fixed regulators as we don't
have support for it's cpcap PMIC. I'll be posting regmap_spi
based minimal cpcap patches later on for USB and the debug
UART on droid 4 multiplexed with the USB connector.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the nodes for the MSTPRI configuration and DDR2/mDDR memory
controller drivers to da850.dtsi.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This patch adds the QSPI clock for stm32f469 discovery board.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
The STMicrolectornics's STM32F746 MCU has the following main features:
- Cortex-M7 core running up to @216MHz
- 1MB internal flash, 320KBytes internal RAM (+4KB of backup SRAM)
- FMC controller to connect SDRAM, NOR and NAND memories
- Dual mode QSPI
- SD/MMC/SDIO support
- Ethernet controller
- USB OTFG FS & HS controllers
- I2C, SPI, CAN busses support
- Several 16 & 32 bits general purpose timers
- Serial Audio interface
- LCD controller
- HDMI-CEC
- SPDIFRX
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
It is the 10th processor in the well-known imx6 series, and derived
from imx6ul but cost optimized. The more information about imx6ull
can be found at:
http://www.nxp.com/products/microcontrollers-and-processors/
arm-processors/i.mx-applications-processors/i.mx-6-processors
/i.mx6qp/i.mx-6ull-single-core-processor-with-arm-cortex-a7-core
:i.MX6ULL
imx6ul.dtsi is the SoC common stuff for both imx6ul and imx6ull;
imx6ul-14x14-evk.dts is the board common stuff for both imx6ul
and imx6ull 14x14 evk. In this patch, for SoC part, the
imx6ull.dtsi includes imx6ul.dtsi; for board part, imx6ull-14x14-evk.dts
includes imx6ul-14x14-evk.dts.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DDR3L is usually specified as
JEDEC standard 1.35V(1.28V~1.45V) & 1.5V(1.425V~1.575V)
Therefore setting smps6 regulator to 1.2V is definitively below
minimum. It appears that real world chips are more forgiving than
data sheets indicate, but let's set the regulator right.
Note: a board that uses other voltages (DDR with 1.5V) can
overwrite by referencing &smps6_reg.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Though the keyboard driver for GPIO buttons(gpio-keys) will continue to
check for/support the legacy "gpio-key,wakeup" boolean property to
enable gpio buttons as wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces the legacy "gpio-key,wakeup" with the unified
"wakeup-source" property in order to avoid any further copy-paste
duplication.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
DMA controller driver is in good shape these days on rockchip platforms.
So lets enable DMA for uart and mmc.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
As explained by commit 9c0da3cc61 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It turns out that the i2c1 adapter is connected to a multiplexer
controlled by a gpio line. The first (default) mux option connects
i2c1 to a bus connected to the already known peripherals. The other
one connects the adapter to the ddc pins of the DVI port.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the schematics of CompuLab's sbc-fx6 baseboard and the
vendor devicetree GPIO_16 is *not* muxed to ENET_REF_CLK but to SPDIF_IN.
Remove the wrong pinctrl setting.
Fixes: 682d055e6a ("ARM: dts: Add initial support for cm-fx6.")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The UART pinmux defines for the pins which are part of the LPSR
pinmux controller are wrong: Output signals configure the input
sel value and the pinmux defines allow not to distinguish between
DCE/DTE mode. Follow the usual pattern using DTE/DCE as part of
the define to denote the two UART configuration options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QP the LDB clock tree has changed to move the clk gate
before the divider, to prevent clock glitches propagating downstream.
A consequence of this change is that the clk divider is now the
parent of the LDB inputs. Reflect this change in the devicetree
to allow the LDB driver to properly configure the display clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
MMDC has a slightly different programming model between imx6q and imx6qp
in terms of perf support, it's exactly same for suspend support, so we
have fsl,imx6q-mmdc here to save patching suspend driver with the new
compatible.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a compatible entry for the specific board versions.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board is now manufactured by Aries Embedded GmbH, update compat string.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The idea is to give useful names to GPIO lines that an implementer
will be using from userspace, e.g. for maker type projects. These are
user-visible using tools/gpio/lsgpio.c
v2: Major rewrite by anholt: Flatten each GPIO line to a line in the
file for better diffing, prefix all expansion header pins with
"P<number>" or "P5HEADER_P<number>" and drop the mostly-unused
GPIO_GEN<smallnumber> names in favor of GPIO<socgpionumber>, fix
extra '[]' on a couple of lines, fix locations of SD_CARD_DETECT,
CAM_GPIO and STATUS_LED, fix HDMI_HPD polarities, rewrite A+ using
unreleased schematics.
v3: More changes by anholt: Drop P<number> / P5HEADER<number>
prefixes. I had been skeptical about adding them, and was
convinced to drop them by Gottfried (who probably has more
experience with GPIOs in educational contexts than the rest of
us). Also drop [] brackets for "is pinmuxed", which didn't seem
to clarify, and were ambiguous for things like the SPI_*-labeled
pins which may or may not actually be pinmuxed to SPI.
v4: Rename B+'s SDA0/SCL0 to match the other boards, despite the
naming on its schematic.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add the node for the thermal sensor of the bcm2835-soc
to the device tree.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Changelog:
V1 -> V5: generic settings is shared in bcm283x.dtsi, but disabled
moved the compatible string to the SOC specific dtsi
for arm and arm64
V5 -> V6: fix remove 0x prefix from thermal@0x7e212000
Note: there is no arm/boot/dts/bcm2837.dtsi as of now,
so the 32-bit rpi3 dt is not modified.
Signed-off-by: Eric Anholt <eric@anholt.net>
We used to use a fixed rate clock for the UARTs. Now that we have clock
support we can associate the correct clocks to the UARTs and drop the
26MHz fixed rate UART clock.
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clock controller nodes for MT2701, include topckgen, infracfg,
pericfg and apmixedsys. This patch also add two oscillators that
provide clocks for MT2701.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Rename sound card to differentiate B2120 and B2260 sound card.
Sound card name is used by alsa-lib to load associated card
configuration file.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Lots of platforms contain clocks which if turned off would prove fatal.
The only way to recover is to restart the board(s). This driver takes
references to clocks which are required to be always-on. The Common
Clk Framework will then take references to them. This way they will
not be turned off during the clk_disabled_unused() procedure.
In this patch we are identifying clocks, which if gated would render
the STiH407 development board unserviceable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
The DRA718-evm is a board based on TI's DRA718 processor targeting
BOM-optimized entry infotainment systems and is a reduced pin and
software compatible derivative of the DRA72 ES2.0 processor.
This platform features:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- uSD
- 8GB eMMC
- CAN
- PCIe
- USB3.0
- Video Input Port
- LP873x PMIC
More information can be found here[1].
Adding support for this board while reusing the data available in
dra72-evm-common.dtsi.
[1] http://www.ti.com/product/dra718
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dra72-evm-common.dtsi consolidates dra72-evm.dts and dra72-evm-revc.dts
which also include tps65917 pmic support as both the evms uses the same
pmic. But, dra71-evm has mostly similar features with a different pmic.
In order to exploit dra72-evm-common.dtsi, creating a separate dtsi
for tps65915 support and including it in respective board files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add proper description of input voltage regulators and update the voltage
rail map for all the regulators.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due
to the limitations introduced by erratum ID: i869[1] (IO Glitches
can occur when changing IO settings) and elaborated in the Technical
Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
Only peripheral that is permitted for dynamic pin mux configuration
is MMC and DCAN. MMC is permitted to change to accommodate the
requirements for varied speeds (which require IO-delay support in
kernel as well). DCAN is a result of i893[1] (DCAN initialization
sequence). With the exception of DCAN and MMC, all other pin mux
configurations are removed from the dts.
[1] http://www.ti.com/lit/er/sprz436a/sprz436a.pdf
[2] http://www.ti.com/lit/ug/spruhz7c/spruhz7c.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change is needed in order to enable some hardware components
from bootloader.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SoC specific and the external
clock is board dependent. Assigning the corresponding clocks.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SoC specific and the external
clock is board dependent. Assigning the corresponding clocks.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SoC specific and the external
clock is board dependent. Assigning the corresponding clocks.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
commit ("766a1fe78fc3 ARM: omap3: Add missing memory node") had
fixes for Torpedo and Overo boards, but this SOM-LV was missed.
This should help prevent the DTC warning:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the power button driver gets corresponding IRQ number by
using platform_get_irq().
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the charger driver gets corresponding IRQ number by using
platform_get_irq_byname() helper.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x bone based boards have the PMIC interrupt named NMI which is
connected to TPS65217 device. AM335x main interrupt controller provides it
and the number is 7.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support the power button driver and disable it by default.
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
TPS65217 MFD driver supports the IRQ domain to handle the charger input
interrupts and push button status event. The interrupt controller enables
corresponding IRQ handling in the charger[*] and power button driver[**].
[*] drivers/power/supply/tps65217_charger.c
[**] drivers/input/misc/tps65218-pwrbutton.c
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In drivers/mmc/core/host.c, there is a "max-frequency" property.
Behavior should not change, so use the "max-frequency" instead of
"clock-freq-min-max".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
In drivers/mmc/core/host.c, there is "max-frequency" property.
It should be same behavior. So use the "max-frequency" instead of
"clock-freq-min-max".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable the QSPI node and add the flash chip.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v3: Use n25q00 for the compatible entry for the flash part and
tested on SoCKit
v2: Remove partition entries for the SoCKIT
Add a more specific board compatible entry for all of the SOCFPGA
Cyclone 5 based boards.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
---
v3: Be a bit more specific with the c5 dk and sockit, use
"altr,socfpga-cyclone5-socdk" and "terasic,socfpga-cyclone5-sockit"
v2: remove extra space and add a comma between compatible entries
According to the latest best practices, unit-addresses should be
represented without any leading zeroes.
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit ("766a1fe78fc3 ARM: omap3: Add missing memory node") added
the memory node, but the patch didn't have the correct starting address.
This patch fixes the correct starting address.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sama5d2 has some static RAM that can be erased by the security module,
add its node
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Now that there is support for the sama5d4 slow clock controller, use its
driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The actual frequency was updated in commit ae142bd997 ("ARM: mvebu:
Fix the main PLL frequency on Armada 375, 38x and 39x SoCs") but the
comment was not updated. Update it now.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Drivers using pinctrl-single,pins have #pinctrl-cells = <1>, while
pinctrl-single,bits need #pinctrl-cells = <2>.
Note that this patch can be optionally applied separately from the
driver changes as the driver supports also the legacy binding without
#pinctrl-cells.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This enables the GPU node for tegra124 nyan boards, which is required to
get graphics acceleration with nouveau on these devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device node for the GMI controller found on Tegra30.
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Colibri T20/T30 on EvalBoard V3.x and GMI-Memory Board
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a device node for the GMI controller found on Tegra20.
Signed-off-by: Mirza Krak <mirza.krak@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Colibri T20/T30 on EvalBoard V3.x and GMI-Memory Board
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
We need to change trimming value (as a percentage) of the 17.78mA TX
reference current for better signal quality. With this change, we
can pass the eye-diagram test on this board.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
We need to change trimming value (as a percentage) of the 17.78mA TX
reference current for better signal quality. With this change, we
can pass the eye-diagram test on this board.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Currently driver leaves sdmmc frequency at its default.
So lets set this to 50MHz.
This gives us performance boost in mmc transfers.
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Exynos4 like other Cortex-A9 SoC's has a Snoop Control Unit(SCU)
and its SFR are used during SMP boot and S2R. Add SCU node to the device tree.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
These hardware blocks are SoC-specific, so their compatible strings
should be SoC-specific as well. This change has no impact on the
actual behavior since it is controlled by the generic "simple-mfd",
"syscon" compatible strings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I notice some mistakes in the SoC DTSI; wrong interrupts properties
of timer nodes, mismatch between the node name and the compatible
for sdctrl block. Given those problems fixed, the common parts
among SoCs are less than I had first expected. The more and more
property overrides are making the SoC DTSI unreadable.
Stretch out the SoC DTSI files and fix the following:
- Fix the 3rd cell of the interrupts property of the timer nodes
for Pro4, Pro5, PXs2
- Fix the node name mioctrl to sdctrl for Pro5, PXs2
- Fix the second region of l2 node for PXs2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
imx-weim should always set address-cells to 2,
and size_cells to 1.
On imx6, fsl,weim-cs-gpr will always be &gpr
Set these common parameters in the dtsi file,
rather than in a downstream dts.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since commit fa93fd4ecc ("regulator: core: Ensure we are at least in
bounds for our constraints") the imx53-qsb board populated with a Dialog
DA9053 PMIC fails to boot:
LDO3: Bringing 3300000uV into 1800000-1800000uV
The LDO3 voltage constraints passed in the device tree do not match
the valid range according to the datasheet, so fix this accordingly to
allow the board booting again.
While at it, fix the other voltage constraints as well.
Cc: <stable@vger.kernel.org> # 4.7.x
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add a CPU clock to every CPU node and a CPU OPP table to use the
generic cpufreq driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
The System Control node has 0x10000 byte of registers. The current
reg size must be expanded to use the cpufreq driver because the
registers controlling CPU frequency are located at offset 0x8000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch adds lsi / lse oscillators. These clocks can be use by
RTC clocks.
The clock drivers needs to disable the power domain write protection using
syscon / regmap to enable these clocks.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch aligns clocks names and node reference according to new
stm32-dwmac glue binding. It also renames Ethernet pinctrl phandle
(indeed there is no need to add 0 as Ethernet instance as there is only
one IP in SOC).
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
stm32f469-disco and stm32f429-eval boards use SDRAM start address remapping
(to @0) to boost performances. A DMA translation through "dma-ranges"
property was needed for other masters than the M4 CPU.
stm32f429-disco doesn't use remapping so doesn't need this DMA translation.
This patches moves this DMA translation definition from stm32f429 soc file
to board files.
Tested-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Up to now a working i2c bus depended on the bootloader to configure the
pinmuxing. Make it explicit.
As a side effect this change makes i2c work in barebox.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add device tree for the Oxford Seminconductor OX820 SoC and the
Cloud Engines PogoPlug v3 board.
Add the SoC and board compatible strings to oxnas bindings.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
DU0 uses an externally provided clock, but the corresponding pin isn't
correctly muxed. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9c0da3cc61 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated"), including skeleton.dtsi is deprecated.
This fixes the following warning with W=1:
Warning (unit_address_vs_reg): Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The system uses one address cell and one size cell, not two. Fix the DU
DT node.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add support in the dts for the HDMI input. Based on the Lager dts
patch from Ulrich Hecht.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[uli: removed "renesas," prefixes from pfc nodes]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT entries for vin0, vin0_pins, and adv7612.
Sets the 'default-input' property for ADV7612, enabling image and video
capture without the need to have userspace specifying routing.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
[uli: added interrupt, renamed endpoint, merged default-input]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,dvc/dvc@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,dvc/dvc@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,mix/mix@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,mix/mix@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ctu/ctu@7 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,src/src@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@7 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@8 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound@ec500000/rcar_sound,ssi/ssi@9 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since 16ccaf5bb5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 parts of the MSIOF0/1 device nodes.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the MSIOF0/1 clocks and their parent, MP clock in the R8A7792
device tree.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
