Without this you will get a panic if the device initialization
fails. Also, free ath_hw instance properly. ath9k_hw_deinit()
shouldn't do it.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9271 needs a full reset only upon the first reset, add
a call for the driver to enable these special resets. We
can optimize this out later without an export.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When initializing the PLL on AR9271 we always need
to set the core clock to 117MHz. While at it remove
the baud rate settings for the serial device on the
AR9271, the default settings work well unless you
want to customize it.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Periodic power amplifier offset calibration is skipped on ath9k
algorithmically, this is required on AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noisefloor values read on AR9271 are unreliable if they
are less than -114, set those statically to -116.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Noisefloor calibration involves querying hardware for samples
and storing this information on a history buffer in hardware for
actual noisefloor calibration processing in hardware. The history
buffer supports collecting information for all Atheros hardware,
one history buffer slot for each chain on each channel used for
MIMO operation. For current hardware this means one history
buffer slot for each chain on both the control (or primary) channel
and the extension (or secondary) channel. We know which noisefloor
registers to poke for collecting noisefloor data through the
chainmask.
For AR9285 and AR9271 devices, both 1x1, the chaimmask is defined as
0x9 = 0b0001001. The first four bits represent each chain out of
a maximum of 4 chains [0-3] on the primary channel. The last four
bits represent each chain on the extension channel. A chainmask
of 0x9 therefore indicates chain 1 is active on both the primary
and the extension channel.
AR9271 only requires collecting and storing noisefloor history buffer
data for the first chain on both the control and extension channel
(nfarray[0] and nfarray[3]) so fix the code and avoid which reads
and writes to the history buffer for the other chains.
Since the noisefloor varies depending on the number of chains your
device supports also initialize the noisefloor history buffer with
reasonable values seen on 1x1 devices such as AR9285.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After telling the AR9271 to go into full sleep we do not need
to clear the RTC reset signal.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TX descriptors setup for AR971 requires the same
setup as AR9285, so use that.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chip test is not required for AR9271 on the host driver
code as the firmware will do the test internally on its own.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign the proper number of GPIO pins for AR9271.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update the register initialization values for AR9271.
This is based on our last review from our systems team.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From e74b075cdb143d45be9b371ee8a8e2dcfc15ab34 Mon Sep 17 00:00:00 2001
From: Ming Lei <tom.leiming@gmail.com>
Date: Sat, 27 Feb 2010 23:50:54 +0800
Subject: [PATCH] ath9k: decrease size of ath9k.ko
The patch defines the fields of 'valid_single_stream' and 'valid' in
struct ath_rate_table as char type, so decrease the size of ath9k.ko
about 2KB.
old ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
69344 3080 168 72592 11b90 ath9k.ko
new ath9k.ko
[tom@tom-lei ath9k]$ size ath9k.ko
text data bss dec hex filename
67304 3080 168 70552 11398 ath9k.ko
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the rate control tx status update gets called for every
subframe of an A-MPDU, and ath9k marks the frame with the relevant
status update with an internal flag. This not suitable for rate control
algorithms using the standard mac80211 rate control API, so fix this by
using IEEE80211_TX_STAT_AMPDU for marking the correct frames that
should be processed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR_IMR_S2 register sometimes cannot be read correctly. Instead of a
valid value, 0xdeadbeef is returned. The driver has been observed
writing that value back to AR_IMR_S2 after changing a few bits.
Cache the register value in ah->imrs2_reg and always write chached value
to the register.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handling HT configuration changes involved setting the channel
with the new HT parameters and then issuing a rate_update()
notification to the driver.
This behavior changed after the off-channel changes. Now, the channel
is not updated with the new HT params in enable_ht() - instead, it
is now done when the scan work terminates. This results in the driver
depending on stale information, defaulting to non-HT mode always.
Fix this by passing the new channel type to the driver.
Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While ath9k does not support RIFS yet, the ability to receive RIFS
frames is currently enabled for most chipsets in the initvals.
This is causing baseband related issues on AR9160 and AR9130 based
chipsets, which can lock up under certain conditions.
This patch fixes these issues by overriding the initvals, effectively
disabling RIFS for all affected chipsets.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Acked-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This converts ath9k to use the new station
add/remove callbacks instead of using the
old sta_notify callback.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In AP mode, ath_beacon_config_ap only restarts the timer if a TSF
restart is requested. Apparently this was added, because this function
unconditionally sets the flag for TSF reset.
The problem with this is, that ath9k_hw_reset() clobbers the timer
registers (specified in the initvals), thus effectively disabling the
SWBA interrupt whenever a card reset without TSF reset is issued
(happens in a few places in the code).
This patch fixes ath_beacon_config_ap to only issue the TSF reset flag
when necessary, but reinitialize the timer unconditionally. Tests show,
that this is enough to keep the SWBA interrupt going after a call to
ath_reset()
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When selecting the tx fallback rate, rc.c used a separate variable
'nrix' for storing the next rate index, however it did not use that as
reference for further rate index lowering. Because of that, it ended up
reusing the same rate for multiple multi-rate retry stages, thus
decreasing delivery probability under changing link conditions.
This patch removes the separate (unnecessary) variable and fixes
fallback the way it was intended to work.
This should result in increased throughput and better link stability.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcoding the lowest rate for Beacon frames, use the rate
index specified in the mac80211 TX info in AP mode.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding support for setting the coverage class in some cases broke
association and data transfer, as it overwrote the initial ACK timeout
value from the initvals with a smaller value.
I don't know why the new value works in 5 GHz (matches the initval
there), but not in 2.4 GHz (initvals use 64us here), so until the
problem is fully understood, the value should be increased again.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, PAE frames are not assigned proper sequence numbers.
Since sending PAE frames as part of aggregates breaks
crupto with several APs, they are sent as normal MPDUs.
Fix the seqeuence number issue by updating the frame with the
internal sequence number.
Tested-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If split tkip key is used, ath_delete_key should delete
rx key and rx mic key. This patch fixes the leak of hw
keycache in the case.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TIM timer interrupt is enabled even before the ACK of nullqos
is received which is unnecessary.
Also clean up the CONF_PS part of config callback properly for
better readability.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
beacons configuration SHOULD be done only if the STA is associated.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some single chip family devices are sold in the market with
802.11n bonded out, these have no hardware capability for
802.11n but ath9k can still support them. These are called
AR2427.
Cc: stable@kernel.org
Reported-by: Rolf Leggewie <bugzilla.kernel.org@rolf.leggewie.biz>
Tested-by: Bernhard Reiter <ockham@raz.or.at>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Calling ath_bus_cleanup() after ieee80211_free_hw() resulted in access
to common->bus_ops, which is already freed as part of the device data.
Remove the cleanup field in struct ath_bus_ops, as it was never used
properly. Remove ath_bus_cleanup(). Merge cleanup functions in place
of the ath_bus_cleanup() calls. Take care not to use any device data
after ieee80211_free_hw().
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using stack for that causes warnings with CONFIG_FRAME_WARN=1024
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Numeric channel is hard to get, so it won't be printed. Replace Mhz
with MHz on the affected lines and add commas as needed.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IDLE PS (Full Sleep) doesn't work when ifconfig up
is done during Idle unassociated state.
Fix this by restoring FULL SLEEP in ps_restore if CONF_IDLE
is set.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k currently forces hw->max_rate_tries to 4 to work around rate
control inefficiencies. This has some negative side effects, such as
rate_control_send_low also using a maximum of 4 tries, which could
negatively affect reliability of unicast management frames.
This patch pushes the retry limit to the rate control instead, and
allows it to use more tries on the last stage to prevent unnecessary
packet loss.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Among other changes, this commit:
commit 06d0f0663e
Author: Sujith <Sujith.Manoharan@atheros.com>
Date: Thu Feb 12 10:06:45 2009 +0530
ath9k: Enable Fractional N mode
changed the hw attach code to fix up initialization values only for
dual band devices, however the commit message did not give a reason as
to why this would be useful or necessary.
According to tests by Jorge Boncompte, this breaks at least some
2GHz-only cards, so the code should be changed back to the
unconditional INI fixup.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Jorge Boncompte <jorge@dti2.net>
Cc: stable@kernel.org
Tested-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As all bt packets are priority traffic during bt scan, wifi
will get disconnected when bt scan lasts for few seconds. Fix
this by allocating 10% of bt period time (4.5ms) to wifi fully.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When cleaning up beacon buffers and slots, ath9k currently checks if
sc->ah->opmode is set to a beacon related mode before cleaning up
buffers.
An unfortunate ordering of interface up/down commands can lead to
sc->ah->opmode being set to monitor mode, while there are AP interfaces
present on the same wiphy.
Always cleaning up beacon buffers if present fixes this issue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users wishing to tweak tx power want it to happen immediately,
try to respect that. This was tested by Lorenzo by measuring the
received signal strength from an AP with ath9k and the patch.
Changing the tx power on the AP produced these results:
1) iwconfig wlan0 txpower 20 ---> Rx power -37dbm
2) iwconfig wlan0 txpower 15 ---> Rx power -41dbm
3) iwconfig wlan0 txpower 10 ---> Rx power -45dbm
4) iwconfig wlan0 txpower 5 ---> Rx power -51dbm
5) iwconfig wlan0 txpower 0 ---> Rx power -37dbm
The result with 0 is an anomoly and would need to be
addressed through a separate patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Tx DMA descriptor has two kinds of flags that select RTS/CTS usage.
The first one (global for the frame) selects whether RTS/CTS or
CTS-to-self should be used, the second one enables RTS/CTS or
CTS-to-self usage for an individual multi-rate-retry entry.
Previously the code preparing the descriptor only enabled the global
flag, if the first MRR series selected the local one.
Fix this by enabling the global flag if any of the MRR entries need it.
With this patch, rate control can properly select the use of RTS/CTS
for all MRR entries except the first one, which is the default behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
