Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Register the 5V boost converter as a regulator named "usb_otg_vbus".
This commit also adds support for bq24190_platform_data, through which
non device-tree platforms can pass the regulator_init_data (containing
mappings for the consumer amongst other things).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Support data memory update on BQ27425. Parameters from TI datasheets are also
provided for BQ27500, 545, 421, 441, 621; however these are commented out,
as they are not tested.
Add BQ27XXX_O_CFGUP & _O_RAM for use in bq27xxx_chip_data[n].opts
and by data memory update functions.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
For the existing features, these chips act like others already ID'd,
so they had false but functional IDs. We will be adding features
which require correct IDs, so the following IDs are added:
BQ2752X, 531, 542, 546, 742, 425, 441, 621
Chip-specific features are now tracked by BQ27XXX_O_* flags in di->opts.
No functional changes to the driver.
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When the BQ27xxx driver was originally written the w1 subsystem only
allowed device drivers for w1 attached devices to live in the w1
subsystem. Kernel driver subsystems expect that the driver for a device
live in the directory of the subsystem for which it implements
functionality, not in the directory of the bus that it is attached. To
work around this, the BQ27xxx driver was implemented as a platform device
driver and the interface driver would instantiate this device from within
the w1 directory, then pass a w1 read callback as platform data.
As we can now have the w1 interface driver in the power/supply directory
(like we do already with the i2c interface driver) we can remove this
middle-layer platform driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Previously there was no way to configure these chips in the event that the
defaults didn't match the battery in question.
For chips with RAM data memory (and also those with flash/NVM data memory
if CONFIG_BATTERY_BQ27XXX_DT_UPDATES_NVM is defined and the user has not
set module param dt_monitored_battery_updates_nvm=0) we now call
power_supply_get_battery_info(), check its values, and write battery
properties to chip data memory if there is a dm_regs table for the chip.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add these to enable read/write of chip data memory RAM/NVM/flash:
bq27xxx_battery_seal()
bq27xxx_battery_unseal()
bq27xxx_battery_set_cfgupdate()
bq27xxx_battery_soft_reset()
bq27xxx_battery_read_dm_block()
bq27xxx_battery_write_dm_block()
bq27xxx_battery_checksum_dm_block()
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Declare bus.write/read_bulk/write_bulk().
Add I2C write/read_bulk/write_bulk() to implement the above.
Add bq27xxx_write/read_block/write_block() helpers to call the above.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: "Andrew F. Davis" <afd@ti.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Userspace prefers the driver having a status property over having to guess
itself. Specifically this will properly make the GNOME3 UI (and likely
others) properly show discharging / charging / full status, instead
of always showing discharging as status.
Note that in the case there is no charger driver supplying the max17042,
then a status of unknown will get returned. At least upower treats
this the same as not having a status attribute, so in this case nothing
changes from a userspace pov.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Some x86 machines use a max17047 fuel-gauge and x86 might be missing
platform_data if not provided by SFI.
This commit adds default platform_data as fallback option so that the
driver can work on boards where no platform_data is provided.
Since not all boards have a thermistor hooked up, set temp_min to 0 and
change the health checks from temp <= temp_min to temp < temp_min to
not trigger on such boards (where temp reads 0).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The i2c-core already maps of irqs before calling the driver's probe
function and there are no in tree users of
bq24190_platform_data->gpio_int.
Remove the redundant custom irq-mapping code and just use client->irq.
Cc: Liam Breck <kernel@networkimprov.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G4 chip definition to specifically match the
bq27520-G4 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G3 chip definition to specifically match the
bq27520-G3 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G2 chip definition to specifically match the
bq27520-G2 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27520G1 chip definition to specifically match the
bq27520-G1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G3 chip definition to specifically match the
bq27510-G3 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Tested-by: Chris Lapa <chris@lapa.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G2 chip definition to specifically match the
bq27510-G2 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27510G1 chip definition to specifically match the
bq27510-G1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This commit adds the BQ27500 chip definition to specifically match the
bq27500/1 functionality as described in the datasheet.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The BQ2751X definition exists only to satisfy backwards compatibility.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The BQ2750X definition exists only to satisfy backwards compatibility.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The BQ27510 and BQ27520 use a slightly different register map than the
BQ27500, add a new type enum and add these gauges to it.
Fixes: d74534c277 ("power: bq27xxx_battery: Add support for additional bq27xxx family devices")
Based-on-patch-by: Kenneth R. Crudup <kenny@panix.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Fix issue with poll_interval being not updated till the previous
interval expired.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Liam Breck <liam@networkimprov.net>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
There where still a few lingering references to pdata after commit
power: supply: sbs-battery: simplify DT parsing.
Remove pdata from struct·sbs_info and conditional checks to ser if this
was set from the i2c read / write functions.
Instead of call max in each function for incrementing poll_retry_count
do it once in the probe function.
Fixup null pointer dereference in to pdata in sbs_external_power_changed.
Change retry counts to u32 to avoid need for max.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This requests the status GPIO with initial input setup. It is required
to read the GPIO status at probe time and thus correctly avoid sending
I2C messages when AC is not plugged.
When requesting the GPIO without initial input setup, it always reads 0
which causes probe to fail as it assumes the charger is connected, sends
I2C messages and fails.
While at it, this switches the driver over to gpiod API.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Switch to using new gpio_desc interface and devm gpio get calls to
automatically manage gpio resource. Use gpiod_get_value which handles
active high / low calls.
If gpio_detect is set then force loading of the driver as it is
reasonable to assume that the battery may not be present.
Update the is_present flag immediately in the IRQ.
Remove legacy gpio specification from platform data.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The max8903_charger.h file indicated that dcm and dok were not optional
when dc_valid is set.
It makes sense to have dok as a compulsory pin when dc_valid is given.
However dcm can be optionally wired to a fixed level especially when the
circuit is configured for dc power exclusively.
The previous implementation already allowed for this somewhat, however no
error was given if dok wasn't given whilst dc_valid was.
The new implementation enforces dok presence when dc_valid is given. Whilst
allowing dcm to be optional.
Signed-off-by: Chris Lapa <chris@lapa.com.au>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
* add types for USB Type C and PD chargers
* add act8945a charger driver
* add ACPI/DT bindings for goldfish-battery
* add support for versatile reset controller
* misc. fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCgAGBQJW6XstAAoJENju1/PIO/qaSmMP+gJY9U4yPscEoW2UkvKJ2y81
/Bxvy8GWSnnaFFPLMHYk/n53EPJbPnewETBftv1xRHzgJ6wQlgM/5EAEU2Qwud+A
V8K3V8VStIZLIrQ1tU8r10UE5OW95lsupCAlFp9AHYrBgIiRDUHlqWtxuhwH12F2
uLZt7moLHJFZtvg3EWl4agsvoEWfqPOKwmOpda+PyIUOlZrAIu3nItvKwBKWdvr3
WuomqfknkekkvX2lSB8R4OfE+w4fkYTFak2+4ymNiaQWrLeEqLuJbICUNGMD+APb
nX8TmQ8wmYYHLZTu455ctGJIdpYfrRI/IPAsdW/vMYnQ/8GiO0dgke5dfzZU08Du
PAWb/NM2pjFfG76fqG46hQPq/Jsns9k/SM1e3Q6fCkwewqtx8P56vUML6FtomYe7
HP3oPqlNeEpcF/jMmxKfSNiF78pmRLpCkWuhhYaT4Suv8bJhoQRE7Ur00Y47hp9i
taAIDE3HNFucqTEXMudBktEKsDPRpEx2K1fZEvZbCF8sOUK4xWPQr1yuPTXrM7jm
sWl/T4s1tn9/P6esdZUTXGghBiehj71mCHsOfXBQZPifaB2s8uINEf+GHQyQcLL4
X2HiMWrv9Pyn+PLVVwWRmTpSVIFWrCHNQPQ1ofgsgWkrEqsAbdZ4O2srlCqg/4WL
irCHBm6fbGpoVRQHg3xS
=L4ho
-----END PGP SIGNATURE-----
Merge tag 'for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset changes from Sebastian Reichel:
- add types for USB Type C and PD chargers
- add act8945a charger driver
- add ACPI/DT bindings for goldfish-battery
- add support for versatile reset controller
- misc fixes
* tag 'for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
power: pm2301-charger: use __maybe_unused to hide pm functions
power: ipaq-micro-battery: use __maybe_unused to hide pm functions
power_supply: 88pm860x_charger: do not pass NULL to power_supply_put
jz4740-battery: Correct voltage change check
power_supply: lp8788-charger: initialize boolean 'found'
goldfish: Enable ACPI-based enumeration for goldfish battery
power: goldfish_battery: add devicetree bindings
power: act8945a: add charger driver for ACT8945A
power: add documentation for ACT8945A's charger DT bindings
ARM: dts: n900: Rename isp1704 to isp1707 to match correct name
power_supply: bq27xxx_battery: Add of modalias and match table when CONFIG_OF is enabled
power_supply: bq2415x_charger: Add of modalias and match table when CONFIG_OF is enabled
power_supply: bq2415x_charger: Do not add acpi modalias when CONFIG_ACPI is not enabled
power_supply: isp1704_charger: Add compatible of match for nxp,isp1707
power_supply: isp1704_charger: Error messages when probe fail
power_supply: Add types for USB Type C and PD chargers
power: bq24735-charger: add 'ti,external-control' option
power: bq24735-charger: document 'ti,external-control' option
power: bq24735-charger: fix failed i2c with ac-detect
power: reset: Fix dependencies for !HAS_IOMEM archs
...
Patch <703df6c09795> ("power: bq27xxx_battery: Reorganize I2C
into a module") has removed the device name numbering from
bq27xxx_battery_i2c_probe. Fix that by restoring the code.
Fixes: 703df6c097
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Reviewed-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Implement an 'ti,external-control' option for when the charger
shouldn't be configured by the host.
Signed-off-by: Jonathan Tinkham <sctincman@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Separate out I2C functionality into a module. This fixes several small
issues and simplifies the driver initialization.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add support for additional devices and register equivalent family devices
including the bq27010, bq27210, bq27500, bq27510, bq27520, bq27530,
bq27531, bq27541, bq27542, bq27546, bq27545, bq27441, bq27421, and the
bq27641.
To facilitate this process the register mapings have been moved to tables
and other small cleanups have been made.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
When initialized as a platform device the initializer must now specify
a device. An empty device name is no longer valid.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
By accident I stumbled over a few misspelled words in the
charger-manager header file which this patch fixes. Namely:
- Extcon rather than Exton
- constraint rather than constratint
- existence rather than existance
- difference rather than diffential
While at it also add a missing space before a closing comment star
forward-slash.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch adds the support for following battery properties
to max17042 fuel gauge driver.
POWER_SUPPLY_PROP_TEMP_ALERT_MIN
POWER_SUPPLY_PROP_TEMP_ALERT_MAX
POWER_SUPPLY_PROP_TEMP_MIN
POWER_SUPPLY_PROP_TEMP_MAX
POWER_SUPPLY_PROP_HEALTH
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Currently, max17042 battery driver choose register map by MAX17042_DevName
register. But it is return IC specific firmware version. So other maxim chip
hard to use this drvier. This patch choose chip type from driver_data.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Change the ownership of power_supply structure from each driver
implementing the class to the power supply core.
The patch changes power_supply_register() function thus all drivers
implementing power supply class are adjusted.
Each driver provides the implementation of power supply. However it
should not be the owner of power supply class instance because it is
exposed by core to other subsystems with power_supply_get_by_name().
These other subsystems have no knowledge when the driver will unregister
the power supply. This leads to several issues when driver is unbound -
mostly because user of power supply accesses freed memory.
Instead let the core own the instance of struct 'power_supply'. Other
users of this power supply will still access valid memory because it
will be freed when device reference count reaches 0. Currently this
means "it will leak" but power_supply_put() call in next patches will
solve it.
This solves invalid memory references in following race condition
scenario:
Thread 1: charger manager
Thread 2: power supply driver, used by charger manager
THREAD 1 (charger manager) THREAD 2 (power supply driver)
========================== ==============================
psy = power_supply_get_by_name()
Driver unbind, .remove
power_supply_unregister()
Device fully removed
psy->get_property()
The 'get_property' call is executed in invalid context because the driver was
unbound and struct 'power_supply' memory was freed.
This could be observed easily with charger manager driver (here compiled
with max17040 fuel gauge):
$ cat /sys/devices/virtual/power_supply/cm-battery/capacity &
$ echo "1-0036" > /sys/bus/i2c/drivers/max17040/unbind
[ 55.725123] Unable to handle kernel NULL pointer dereference at virtual address 00000000
[ 55.732584] pgd = d98d4000
[ 55.734060] [00000000] *pgd=5afa2831, *pte=00000000, *ppte=00000000
[ 55.740318] Internal error: Oops: 80000007 [#1] PREEMPT SMP ARM
[ 55.746210] Modules linked in:
[ 55.749259] CPU: 1 PID: 2936 Comm: cat Tainted: G W 3.19.0-rc1-next-20141226-00048-gf79f475f3c44-dirty #1496
[ 55.760190] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 55.766270] task: d9b76f00 ti: daf54000 task.ti: daf54000
[ 55.771647] PC is at 0x0
[ 55.774182] LR is at charger_get_property+0x2f4/0x36c
[ 55.779201] pc : [<00000000>] lr : [<c034b0b4>] psr: 60000013
[ 55.779201] sp : daf55e90 ip : 00000003 fp : 00000000
[ 55.790657] r10: 00000000 r9 : c06e2878 r8 : d9b26c68
[ 55.795865] r7 : dad81610 r6 : daec7410 r5 : daf55ebc r4 : 00000000
[ 55.802367] r3 : 00000000 r2 : daf55ebc r1 : 0000002a r0 : d9b26c68
[ 55.808879] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
[ 55.815994] Control: 10c5387d Table: 598d406a DAC: 00000015
[ 55.821723] Process cat (pid: 2936, stack limit = 0xdaf54210)
[ 55.827451] Stack: (0xdaf55e90 to 0xdaf56000)
[ 55.831795] 5e80: 60000013 c01459c4 0000002a c06f8ef8
[ 55.839956] 5ea0: db651000 c06f8ef8 daebac00 c04cb668 daebac08 c0346864 00000000 c01459c4
[ 55.848115] 5ec0: d99eaa80 c06f8ef8 00000fff 00001000 db651000 c027f25c c027f240 d99eaa80
[ 55.856274] 5ee0: d9a06c00 c0146218 daf55f18 00001000 d99eaa80 db4c18c0 00000001 00000001
[ 55.864468] 5f00: daf55f80 c0144c78 c0144c54 c0107f90 00015000 d99eaab0 00000000 00000000
[ 55.872603] 5f20: 000051c7 00000000 db4c18c0 c04a9370 00015000 00001000 daf55f80 00001000
[ 55.880763] 5f40: daf54000 00015000 00000000 c00e53dc db4c18c0 c00e548c 0000000d 00008124
[ 55.888937] 5f60: 00000001 00000000 00000000 db4c18c0 db4c18c0 00001000 00015000 c00e5550
[ 55.897099] 5f80: 00000000 00000000 00001000 00001000 00015000 00000003 00000003 c000f364
[ 55.905239] 5fa0: 00000000 c000f1a0 00001000 00015000 00000003 00015000 00001000 0001333c
[ 55.913399] 5fc0: 00001000 00015000 00000003 00000003 00000002 00000000 00000000 00000000
[ 55.921560] 5fe0: 7fffe000 be999850 0000a225 b6f3c19c 60000010 00000003 00000000 00000000
[ 55.929744] [<c034b0b4>] (charger_get_property) from [<c0346864>] (power_supply_show_property+0x48/0x20c)
[ 55.939286] [<c0346864>] (power_supply_show_property) from [<c027f25c>] (dev_attr_show+0x1c/0x48)
[ 55.948130] [<c027f25c>] (dev_attr_show) from [<c0146218>] (sysfs_kf_seq_show+0x84/0x104)
[ 55.956298] [<c0146218>] (sysfs_kf_seq_show) from [<c0144c78>] (kernfs_seq_show+0x24/0x28)
[ 55.964536] [<c0144c78>] (kernfs_seq_show) from [<c0107f90>] (seq_read+0x1b0/0x484)
[ 55.972172] [<c0107f90>] (seq_read) from [<c00e53dc>] (__vfs_read+0x18/0x4c)
[ 55.979188] [<c00e53dc>] (__vfs_read) from [<c00e548c>] (vfs_read+0x7c/0x100)
[ 55.986304] [<c00e548c>] (vfs_read) from [<c00e5550>] (SyS_read+0x40/0x8c)
[ 55.993164] [<c00e5550>] (SyS_read) from [<c000f1a0>] (ret_fast_syscall+0x0/0x48)
[ 56.000626] Code: bad PC value
[ 56.011652] ---[ end trace 7b64343fbdae8ef1 ]---
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[for the nvec part]
Reviewed-by: Marc Dietrich <marvin24@gmx.de>
[for compal-laptop.c]
Acked-by: Darren Hart <dvhart@linux.intel.com>
[for the mfd part]
Acked-by: Lee Jones <lee.jones@linaro.org>
[for the hid part]
Acked-by: Jiri Kosina <jkosina@suse.cz>
[for the acpi part]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
To guerantee proper charing and managing batteries even in suspend,
charger-manager has used rtc device with rtc framework interface.
However, it is better to use alarmtimer for cleaner and more appropriate
operation.
This patch makes driver to use alarmtimer for polling work in suspend and
removes all deprecated codes related with using rtc interface.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
The charger manager obtained reference to fuel gauge power supply in probe
with power_supply_get_by_name() for later usage. However if fuel gauge
driver was removed and re-added then this reference would point to old
power supply (from driver which was removed).
This lead to accessing old (and probably invalid) memory which could be
observed with:
$ echo "12-0036" > /sys/bus/i2c/drivers/max17042/unbind
$ echo "12-0036" > /sys/bus/i2c/drivers/max17042/bind
$ cat /sys/devices/virtual/power_supply/battery/capacity
[ 240.480084] INFO: task cat:1393 blocked for more than 120 seconds.
[ 240.484799] Not tainted 3.17.0-next-20141007-00028-ge60b6dd79570 #203
[ 240.491782] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 240.499589] cat D c0469530 0 1393 1 0x00000000
[ 240.505947] [<c0469530>] (__schedule) from [<c0469d3c>] (schedule_preempt_disabled+0x14/0x20)
[ 240.514449] [<c0469d3c>] (schedule_preempt_disabled) from [<c046af08>] (mutex_lock_nested+0x1bc/0x458)
[ 240.523736] [<c046af08>] (mutex_lock_nested) from [<c0287a98>] (regmap_read+0x30/0x60)
[ 240.531647] [<c0287a98>] (regmap_read) from [<c032238c>] (max17042_get_property+0x2e8/0x350)
[ 240.540055] [<c032238c>] (max17042_get_property) from [<c03247d8>] (charger_get_property+0x264/0x348)
[ 240.549252] [<c03247d8>] (charger_get_property) from [<c0320764>] (power_supply_show_property+0x48/0x1e0)
[ 240.558808] [<c0320764>] (power_supply_show_property) from [<c027308c>] (dev_attr_show+0x1c/0x48)
[ 240.567664] [<c027308c>] (dev_attr_show) from [<c0141fb0>] (sysfs_kf_seq_show+0x84/0x104)
[ 240.575814] [<c0141fb0>] (sysfs_kf_seq_show) from [<c0140b18>] (kernfs_seq_show+0x24/0x28)
[ 240.584061] [<c0140b18>] (kernfs_seq_show) from [<c0104574>] (seq_read+0x1b0/0x484)
[ 240.591702] [<c0104574>] (seq_read) from [<c00e1e24>] (vfs_read+0x88/0x144)
[ 240.598640] [<c00e1e24>] (vfs_read) from [<c00e1f20>] (SyS_read+0x40/0x8c)
[ 240.605507] [<c00e1f20>] (SyS_read) from [<c000e760>] (ret_fast_syscall+0x0/0x48)
[ 240.612952] 4 locks held by cat/1393:
[ 240.616589] #0: (&p->lock){+.+.+.}, at: [<c01043f4>] seq_read+0x30/0x484
[ 240.623414] #1: (&of->mutex){+.+.+.}, at: [<c01417dc>] kernfs_seq_start+0x1c/0x8c
[ 240.631086] #2: (s_active#31){++++.+}, at: [<c01417e4>] kernfs_seq_start+0x24/0x8c
[ 240.638777] #3: (&map->mutex){+.+...}, at: [<c0287a98>] regmap_read+0x30/0x60
The charger-manager should get reference to fuel gauge power supply on
each use of get_property callback. The thermal zone 'tzd' field of
power supply should not be used because of the same reason.
Additionally this change solves also the issue with nested
thermal_zone_get_temp() calls and related false lockdep positive for
deadlock for thermal zone's mutex [1]. When fuel gauge is used as source of
temperature then the charger manager forwards its get_temp calls to fuel
gauge thermal zone. So actually different mutexes are used (one for
charger manager thermal zone and second for fuel gauge thermal zone) but
for lockdep this is one class of mutex.
The recursion is removed by retrieving temperature through power
supply's get_property().
In case external thermal zone is used ('cm-thermal-zone' property is
present in DTS) the recursion does not exist. Charger manager simply
exports POWER_SUPPLY_PROP_TEMP_AMBIENT property (instead of
POWER_SUPPLY_PROP_TEMP) thus no thermal zone is created for this power
supply.
[1] https://lkml.org/lkml/2014/10/6/309
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Cc: <stable@vger.kernel.org>
Fixes: 3bb3dbbd56 ("power_supply: Add initial Charger-Manager driver")
Signed-off-by: Sebastian Reichel <sre@kernel.org>
This patch introduces device tree support to the isp1704 charger driver.
Adding support involved moving the handling of the enable GPIO from board
code into the driver.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This patch removing set_mode_hook function from board data and replacing
it with new string variable of notifier power supply device. After this
change it is possible to add DT support because driver does not need
specific board function anymore. Only static data and name of power supply
device is required.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Charger-manager can parse charger_desc data from devicetree which is used
to register charger manager.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Charger-manager driver used to check battery temperature through the
callback function passed by platform data. Unfortunatley, without that
pre-defined callback function, charger-manager can't get battery's
temperature at all. Also passing callback function through platform data
ruins DT support for charger-manager.
This patch mondifies charger-manager driver to get temperature of battery
without pre-defined callback function. Now, charger-manager can use either
of battery thermometer in fuel-gauge and ouside of battery. It uses
thermal framework interface for outer thermometer if thermal fw is
enabled. Otherwise, it tries to use fuel-gauge's through the power supply
interface.
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Adds support for the bq24735 charger chipset. The bq24735 is a
high-efficiency, synchronous battery charger.
It allows control of the charging current, input current, and the charger
voltage DAC's through SMBus.
Signed-off-by: Darbha Sriharsha <dsriharsha@nvidia.com>
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Thanks-to: Stephen Warren <swarren@wwwdotorg.org>
Thanks-to: Thierry Reding <thierry.reding@gmail.com>
Thanks-to: Manish Badarkhe <badarkhe.manish@gmail.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
This driver is used and tested on gta04 phone. It's using twl4030_madc
(similar to rx51 existing driver). Driver also implement charging and
discharging calibration data so user can define ranges and level.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Lukas Märdian <lukas@goldelico.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
Add driver support for the Texas Instruments BQ24190 battery charger.
Some of the information provided by the device is about the charger and
other information is about the battery so create two power_supply objects
(one for each) and provide the appropriate information for each one.
The device has many fields that go beyond what is reasonable to report or
modify using the existing 'POWER_SUPPLY_PROP_*' properties so the driver
exports the register fields via sysfs. They are prefixed by 'f_' (for
'field') to make it easier to distinguish between a register field and a
"normal" sysfs file exported by the power_supply infrastructure.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Anton Vorontsov <anton@enomsg.org>
SmartReflex driver interface is natively divided to two parts:
- external SmartReflex interface
- interface between SmartReflex driver and SmartReflex Class
Functions which belong to AVS class interface can use
struct omap_sr* instead of struct voltatedomain*, to provide a
direct connection between SR driver and SR class. This allows
us to optimize and not do additional lookups where none is
required.
sr_enable() and sr_disable() are interface functions between
SR driver and SR class. They are typically used by Class driver
to enable/disable SmartReflex hardware module.
Now they take struct omap_sr* as input parameter.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
SmartReflex driver interface is natively divided to two parts:
- external SmartReflex interface
- interface between SmartReflex driver and SmartReflex Class
Functions which belong to AVS class interface can use
struct omap_sr* instead of struct voltatedomain*, to provide a
direct connection between SR driver and SR class. This allows
us to optimize and not do additional lookups where none is
required.
sr_configure_minmax() is interface function between SR driver
and SR class. It is typically used by Class driver to
configure MINMAXAVG module inside SmartReflex module.
Now it takes struct omap_sr* as input parameter.
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
