Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TCON driver used to need the panel pointer in order to configure the
tcon according to the various parameters of the panel. However, this has
evolved over time (especially to support bridges), and therefore the panel
pointer isn't needed anymore by the TCON driver.
Move that pointer to the LVDS and RGB encoders drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # tested on pinebook
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/13288b6b8f27b614a6c9aef348923c34b2803ad4.1551191081.git-series.maxime.ripard@bootlin.com
Some panels need an active-low data enable (DE) signal for the RGB
interface. This requires flipping a bit in the TCON0 polarity register
when setting up the mode for the RGB interface.
Match the associated bus flag and use it to set the polarity inversion
bit for the DE signal when required.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107181843.27628-4-contact@paulk.fr
Dithering is only supported for TCON channel 0. Throughout the datasheet
all the names associated with these register are prefixed "TCON0",
instead of "TCON". The only exception is the control register
"TCON_FRM_CTL_REG".
Rename the macros to reflect this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907041948.19913-3-wens@csie.org
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJauCZfAAoJEHm+PkMAQRiGWGUH/2rhdQDkoJpYWnjaQkolECG8
MxpGE7nmIIHxQcbSDdHTGJ8IhVm6Z5wZ7ym/PwCDTT043Y1y341sJrIwL2/nTG6d
HVidk8hFvgN6QzlzVAHT3ZZMII/V9Zt+VV5SUYLGnPAVuJNHo/6uzWlTU5g+NTFo
IquFDdQUaGBlkKqby+NoAFnkV1UAIkW0g22cfvPnlO5GMer0gusGyVNvVp7TNj3C
sqj4Hvt3RMDLMNe9RZ2pFTiOD096n8FWpYftZneUTxFImhRV3Jg5MaaYZm9SI3HW
tXrv/LChT/F1mi5Pkx6tkT5Hr8WvcrwDMJ4It1kom10RqWAgjxIR3CMm448ileY=
=YKUG
-----END PGP SIGNATURE-----
Backmerge tag 'v4.16-rc7' into drm-next
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
The Allwinner A80 SoC has 2 documented TCONs. The display pipeline
diagram from the user manual shows a third TCON, but it's missing
an interrupt line, and its registers are not explained either.
It's also not used in Allwinner's vendor BSP.
The first TCON only has channel 0, for LCD panel output. The TCON
hardware setup is peculiar in that the eDP reset must also be
deasserted to allow access to the TCON. How the eDP module is wired
in the SoC itself is never explained.
The second TCON only has channel 1, and its output is connected to
the HDMI encoder block.
This patch adds a "needs_edp_reset" field to the tcon quirks structure,
and adds quirks and compatible strings for the 2 documented TCONs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315114136.24747-4-wens@csie.org
The current logic to deal with old DT missing the LVDS properties doesn't
take into account whether the LVDS output is supported in the first place,
resulting in spurious error messages on SoCs where it doesn't even matter.
Introduce a new TCON flag to list if LVDS is supported at all to prevent
this from happening.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180221125703.4595-1-maxime.ripard@bootlin.com
Some TCONs on newer SoCs doesn't support channel 0, since they are meant
to be used only with TV or HDMI encoder.
Prepare support for them with adding has_channel_0 quirk.
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180214200906.31509-8-jernej.skrabec@siol.net
The sun4i DRM driver maintains a list of compatible strings it uses to
check if a device node within the display component graph is a TCON.
The TCON driver also has this list, used to bind the TCON driver to
the device. These two lists are identical.
Instead of maintaining two identical lists, export the list from the
TCON driver for the DRM driver to use.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171127084632.25511-1-wens@csie.org
So far, we've required all the TCON-connected encoders to call the TCON
enable and disable functions.
This was made this way because in the RGB/LVDS case, the TCON is the CRTC
and the encoder. However, in all the other cases (HDMI, TV, DSI, etc.), we
have another encoder down the road that needs to be programmed.
We also needed to know which channel the encoder is connected to, which is
encoder-specific.
The CRTC's enable and disable callbacks can work just fine for our use
case, and we can get the channel to use just by looking at the type of
encoder, since that is fixed. Implement those callbacks, which will
remove some of the encoder boilerplate.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/90b4396e19b3eca61b2ebfdae0672074b88ad74d.1508231063.git-series.maxime.ripard@free-electrons.com
Different SoCs have different muxing options and values for the TCON
outputs. Instead of stuffing every possibility in sun4i_tcon_set_mux(),
add a callback pointer to sun4i_tcon_quirks that each TCON variant
can use to provide muxing support.
The current muxing options in sun4i_tcon_set_mux() for sun5i-a13 are
moved to a new sun5i-specific callback function.
Since the new callback replaces what the .has_unknown_mux field in
tcon quirks did in the past, the field is removed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171010032008.682-2-wens@csie.org
UAPI Changes:
Cross-subsystem Changes:
Core Changes:
- DP SDP defines (Ville)
- polish for scdc helpers (Thierry Reding)
- fix lifetimes for connector/plane state across crtc changes (Maarten
Lankhorst).
- sparse fixes (Ville+Thierry)
- make legacy kms ioctls all interruptible (Maarten)
- push edid override into the edid helpers (out of probe helpers)
(Jani)
- DP ESI defines for link status (DK)
Driver Changes:
- drm-panel is now in drm-misc!
- minor panel-simple cleanups/refactoring by various folks
- drm_bridge_add cleanup (Inki Dae)
- constify a few i2c_device_id structs (Arvind Yadav)
- More patches from Noralf's fb/gem helper cleanup
- bridge/synopsis: reset fix (Philippe Cornu)
- fix tracepoint include handling in drivers (Thierry)
- rockchip: lvds support (Sandy Huang)
- move sun4i into drm-misc fold (Maxime Ripard)
- sun4i: refactor driver load + support TCON backend/layer muxing
(Chen-Yu Tsai)
- pl111: support more pl11x variants (Linus Walleij)
- bridge/adv7511: robustify probing/edid handling (Lars-Petersen
Clausen)
New hw support:
- S6E63J0X03 panel (Hoegeun Kwon)
- OTM8009A panel (Philippe CORNU)
- Seiko 43WVF1G panel (Marco Franchi)
- tve200 driver (Linus Walleij)
Plus assorted of tiny patches all over, including our first outreachy
patches from applicants for the winter round!
* tag 'drm-misc-next-2017-09-20' of git://anongit.freedesktop.org/git/drm-misc: (101 commits)
drm: add backwards compatibility support for drm_kms_helper.edid_firmware
drm: handle override and firmware EDID at drm_do_get_edid() level
drm/dp: DPCD register defines for link status within ESI field
drm/rockchip: Replace dev_* with DRM_DEV_*
drm/tinydrm: Drop driver registered message
drm/gem-fb-helper: Use debug message on gem lookup failure
drm/imx: Use drm_gem_fb_create() and drm_gem_fb_prepare_fb()
drm/bridge: adv7511: Constify HDMI CODEC platform data
drm/bridge: adv7511: Enable connector polling when no interrupt is specified
drm/bridge: adv7511: Remove private copy of the EDID
drm/bridge: adv7511: Properly update EDID when no EDID was found
drm/crtc: Convert setcrtc ioctl locking to interruptible.
drm/atomic: Convert pageflip ioctl locking to interruptible.
drm/legacy: Convert setplane ioctl locking to interruptible.
drm/legacy: Convert cursor ioctl locking to interruptible.
drm/atomic: Convert atomic ioctl locking to interruptible.
drm/atomic: Prepare drm_modeset_lock infrastructure for interruptible waiting, v2.
drm/tve200: Clean up panel bridging
drm/doc: Update todo.rst
drm/dp/mst: Sideband message transaction to power up/down nodes
...
The TCON has a mux to select the source of the data to display.
This mux includes selecting the display backends. On the A31,
which has two display pipelines, this mux can let the TCON
select either backend as its data source. Although the muxing
can be changed on the fly, DRM needs to be able to group a
bunch of layers such that they get switched to another crtc
together. This is because the display backend does the layer
compositing, while the TCON generates the display timings.
This constraint is not supported by DRM.
Here we simply pair up backends and TCONs with the same ID.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170908075016.18657-7-wens@csie.org
Even though that function is defined in the TCON header, it's not defined
nor used anywhere. Remove the prototype.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Both TCON channels need to have the resolution doubled, since the size the
hardware is going to use is whatever we put in the register divided by two.
However, we handle it differently for the two channels: in the channel 0,
our register access macro does the multiplication of the value passed as
paremeter, while in the channel 1, the macro doesn't do this, and we need
to do it before calling it.
Make this consistent by aligning the channel 0 with the channel 1
behaviour.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The muxing can actually happen on both channels on some SoCs, so it makes
more sense to just move it out of the sun4i_tcon1_mode_set function and
create a separate function that needs to be called by the encoders.
Let's do that and convert the existing drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The tcons and backends have a one-to-one relationship. Their IDs,
or indexes in the documentation, are also the same.
Copy the ID from the associated backend and save it in the tcon
structure. This will later be used when we add support for the
output data path muxes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
To support multiple display pipelines, we need to keep track of the
multiple display backends and TCONs registered with the driver.
Switch to lists to track registered components. Components are only
appended to their respective lists if the bind process was successful.
The TCON bind function now defers if a backend was not registered.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The tcon provides part of the functionality of the crtc, and also
provides the device node for the output port of the crtc. To be able
to use drm_of_find_possible_crtcs(), all crtc must be initialized before
any downstream encoders. The other part of the crtc is the display
backend.
The Rockchip DRM driver does this by first binding all vops, which is
their crtc, and this step also creates the crtc objects. Then all
remaining hardware components are bound. With the Allwinner display
pipeline, we have multiple components comprising the crtc, and varying
depths of the display pipeline. Since components are added with a depth
first search of the of_graph, we can initialize the crtc object within
the tcon bind function. Since the backend precedes the tcon, and the
backends cannot be muxed or switched around, we can be sure that the
associated backend is already initialized.
This patch also moves the crtc pointer from the main drm_device data to
the tcon device data. Besides the crtc callbacks, the crtc structure is
only used within the tcon driver to signal vblank events from its
interrupt handler.
As the crtc and layer bits are now called from the tcon bits, we must
move them from the sun4i-drm module to the sun4i-tcon module to avoid
circular dependencies between the two modules. This is because sun4i-drm
also calls into sun4i-tcon.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We already have some differences between the 2 supported SoCs.
More will be added as we support other SoCs. To avoid bloating
the probe function with even more conditionals, move the quirks
to a separate data structure that's tied to the compatible string.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some Allwinner SoCs, such as the A33, have a variation of the TCON that
doesn't have a second channel (or it is not wired to anything).
Make sure we can handle that case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Our RGB bus can be either connected to a bridge or a panel. While the panel
support was already there, the bridge was not.
Fix that.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In order to properly support bridges and use drm_encoder's bridge pointer,
move the panel (and bridge eventually) retrieval code in the RGB output
init function.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We will need to access TCON's struct device from outside of TCON's driver
bind function. Store it in our private structure.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
One of the A10 display pipeline possible output is an RGB interface to
drive LCD panels directly. This is done through the first channel of the
TCON that will output our video signals directly.
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Allwinner A10 and subsequent SoCs share the same display pipeline, with
variations in the number of controllers (1 or 2), or the presence or not of
some output (HDMI, TV, VGA) or not.
Add a driver with a limited set of features for now, and we will hopefully
support all of them eventually
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
