This patch merges the GENEVE and VXLAN code so that both functions pass
through a shared code path. This way we can start the effort of using a
single function on the network device drivers to handle both of these
tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that we add udp_tunnel.h to vxlan.h and geneve.h
header files. This is useful as I plan to move the generic handlers for
the port offloads into the udp_tunnel header file and leave the vxlan and
geneve headers to be a bit more protocol specific.
I also went through and cleaned out a number of redundant includes that
where in the .h and .c files for these drivers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function vxlan_dev_create() (only used by ovs) never calls
rtnl_configure_link(). The consequence is that dev->rtnl_link_state is
never set to RTNL_LINK_INITIALIZED.
During the deletion phase, the function rollback_registered_many() sends
a RTM_DELLINK only if dev->rtnl_link_state is set to RTNL_LINK_INITIALIZED.
Note that the function vxlan_dev_create() is moved after the rtnl stuff so
that vxlan_dellink() can be called in this function.
Fixes: dcc38c033b ("openvswitch: Re-add CONFIG_OPENVSWITCH_VXLAN")
CC: Thomas Graf <tgraf@suug.ch>
CC: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When create a new vxlan link, example:
ip link add vtap mtu 1440 type vxlan vni 1 dev eth0
The argument "mtu" has no effect, because it is not set to conf->mtu. The
default value is used in vxlan_dev_configure function.
This problem was introduced by commit 0dfbdf4102 (vxlan: Factor out device
configuration).
Fixes: 0dfbdf4102 (vxlan: Factor out device configuration)
Signed-off-by: Chen Haiquan <oc@yunify.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For VXLAN-GPE, the interface is ARPHRD_NONE, thus we need to reset
mac_header after pulling the outer header.
v2: Put the code to the existing conditional block as suggested by
Shmulik Ladkani.
Fixes: e1e5314de0 ("vxlan: implement GPE")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP tunnel segmentation code relies on the inner offsets being set for
an UDP tunnel GSO packet, but the inner *_complete() functions will
set the inner offsets only if 'encapsulation' is set before calling
them. Currently, udp_gro_complete() sets 'encapsulation' only after
the inner *_complete() functions are done. This causes the inner
offsets having invalid values after udp_gro_complete() returns, which
in turn will make it impossible to properly segment the packet in case
it needs to be forwarded, which would be visible to the user either as
invalid packets being sent or as packet loss.
This patch fixes this by setting skb's 'encapsulation' in
udp_gro_complete() before calling into the inner complete functions,
and by making each possible UDP tunnel gro_complete() callback set the
inner_mac_header to the beginning of the tunnel payload.
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Reviewed-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The setting of the UDP tunnel GSO type is already performed by
udp[46]_gro_complete().
Signed-off-by: Jarno Rajahalme <jarno@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0c867c9bf8 ("vxlan: move Ethernet initialization to a separate
function") changed initialization order and as an unintended result, when the
user specifies additional link parameters (such as IFLA_ADDRESS) while
creating vxlan interface, those are overwritten by vxlan_ether_setup later.
It's necessary to call ether_setup from withing the ->setup callback. That
way, the correct parameters are set by rtnl_create_link later. This is done
also for VXLAN-GPE, as we don't know the interface type yet at that point,
and changed to the correct interface type later.
Fixes: 0c867c9bf8 ("vxlan: move Ethernet initialization to a separate function")
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Tested-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all drivers depend and autoload the vxlan module because how
vxlan_get_rx_port is linked into them. Remove this dependency:
By using a new event type in the netdevice notifier call chain we proxy
the request from the drivers to flush and resetup the vxlan ports not
directly via function call but by the already existing netdevice
notifier call chain.
I added a separate new event type, NETDEV_OFFLOAD_PUSH_VXLAN, to do so.
We don't need to save those ids, as the event type field is an unsigned
long and using specialized event types for this purpose seemed to be a
more elegant way. This also comes in beneficial if in future we want to
add offloading knobs for vxlan.
Cc: Jesse Gross <jesse@kernel.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the IP tunnel core function iptunnel_handle_offloads so
that we return an int and do not free the skb inside the function. This
actually allows us to clean up several paths in several tunnels so that we
can free the skb at one point in the path without having to have a
secondary path if we are supporting tunnel offloads.
In addition it should resolve some double-free issues I have found in the
tunnels paths as I believe it is possible for us to end up triggering such
an event in the case of fou or gue.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need to do the synchronize_net dance once for both, ipv4 and
ipv6 sockets, thus removing one synchronize_net in case both sockets get
dismantled.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that the udp socket is destructed asynchronously in a
work queue, we have some nondeterministic behavior during shutdown of
vxlan tunnels and creating new ones. Fix this by keeping the destruction
process synchronous in regards to the user space process so IFF_UP can
be reliably set.
udp_tunnel_sock_release destroys vs->sock->sk if reference counter
indicates so. We expect to have the same lifetime of vxlan_sock and
vxlan_sock->sock->sk even in fast paths with only rcu locks held. So
only destruct the whole socket after we can be sure it cannot be found
by searching vxlan_net->sock_list.
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jiri Benc <jbenc@redhat.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The protocol is 16bit, not 32bit.
Fixes: e1e5314de0 ("vxlan: implement GPE")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adapt vxlan_gro_receive, vxlan_gro_complete to take a socket argument.
Set these functions in tunnel_config. Don't set udp_offloads any more.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement VXLAN-GPE. Only COLLECT_METADATA is supported for now (it is
possible to support static configuration, too, if there is demand for it).
The GPE header parsing has to be moved before iptunnel_pull_header, as we
need to know the protocol.
v2: Removed what was called "L2 mode" in v1 of the patchset. Only "L3 mode"
(now called "raw mode") is added by this patch. This mode does not allow
Ethernet header to be encapsulated in VXLAN-GPE when using ip route to
specify the encapsulation, IP header is encapsulated instead. The patch
does support Ethernet to be encapsulated, though, using ETH_P_TEB in
skb->protocol. This will be utilized by other COLLECT_METADATA users
(openvswitch in particular).
If there is ever demand for Ethernet encapsulation with VXLAN-GPE using
ip route, it's easy to add a new flag switching the interface to
"Ethernet mode" (called "L2 mode" in v1 of this patchset). For now,
leave this out, it seems we don't need it.
Disallowed more flag combinations, especially RCO with GPE.
Added comment explaining that GBP and GPE cannot be set together.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle VXLAN_F_COLLECT_METADATA before VXLAN_F_PROXY. The latter does not
make sense with the former, as it needs populated fdb which does not happen
in metadata mode.
After this cleanup, the fdb code in vxlan_xmit is moved to a common location
and can be later skipped for VXLAN-GPE which does not necessarily carry
inner Ethernet header.
v2: changed commit description to not reference L3 mode
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow to initialize vxlan in ARPHRD_NONE mode based on the passed
rtnl attributes.
v2: renamed "l2mode" to "ether".
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_remcsum is called after iptunnel_pull_header and thus the skb has
vxlan header already pulled. Don't include vxlan header again in the
calculation.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri mentioned that flowi6_tos of struct flowi6 is never used/read
anywhere. In fact, rest of the kernel uses the flowi6's flowlabel,
where the traffic class _and_ the flowlabel (aka flowinfo) is encoded.
For example, for policy routing, fib6_rule_match() uses ip6_tclass()
that is applied on the flowlabel member for matching on tclass. Similar
fix is needed for geneve, where flowi6_tos is set as well. Installing
a v6 blackhole rule that f.e. matches on tos is now working with vxlan.
Fixes: 1400615d64 ("vxlan: allow setting ipv6 traffic class")
Reported-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the GRO handlers for GRE, VXLAN, GENEVE, and FOU so that
we do not clear the flush bit until after we have called the next level GRO
handler. Previously this was being cleared before parsing through the list
of frames, however this resulted in several paths where either the bit
needed to be reset but wasn't as in the case of FOU, or cases where it was
being set as in GENEVE. By just deferring the clearing of the bit until
after the next level protocol has been parsed we can avoid any unnecessary
bit twiddling and avoid bugs.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds support for setting the IPv6 flow label for vxlan per
device and through collect metadata (ip_tunnel_key) frontends. The
vxlan dst cache does not need any special considerations here, for
the cases where caches can be used, the label is static per cache.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends udp_tunnel6_xmit_skb() to pass in the IPv6 flow label
from call sites. Currently, there's no such option and it's always set to
zero when writing ip6_flow_hdr(). Add a label member to ip_tunnel_key, so
that flow-based tunnels via collect metadata frontends can make use of it.
vxlan and geneve will be converted to add flow label support separately.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can already do that for IPv4, but IPv6 support was missing. Add
it for vxlan, so it can be used with collect metadata frontends.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The assumptions from commit 0c1d70af92 ("net: use dst_cache for vxlan
device"), 468dfffcd7 ("geneve: add dst caching support") and 3c1cb4d260
("net/ipv4: add dst cache support for gre lwtunnels") on dst_cache usage
when ip_tunnel_info is used is unfortunately not always valid as assumed.
While it seems correct for ip_tunnel_info front-ends such as OVS, eBPF
however can fill in ip_tunnel_info for consumers like vxlan, geneve or gre
with different remote dsts, tos, etc, therefore they cannot be assumed as
packet independent.
Right now vxlan, geneve, gre would cache the dst for eBPF and every packet
would reuse the same entry that was first created on the initial route
lookup. eBPF doesn't store/cache the ip_tunnel_info, so each skb may have
a different one.
Fix it by adding a flag that checks the ip_tunnel_info. Also the !tos test
in vxlan needs to be handeled differently in this context as it is currently
inferred from ip_tunnel_info as well if present. ip_tunnel_dst_cache_usable()
helper is added for the three tunnel cases, which checks if we can use dst
cache.
Fixes: 0c1d70af92 ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd7 ("geneve: add dst caching support")
Fixes: 3c1cb4d260 ("net/ipv4: add dst cache support for gre lwtunnels")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add operation
in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When signalling to metadata consumers that the metadata_dst entry
carries additional GBP extension data for vxlan (TUNNEL_VXLAN_OPT),
the dst's vxlan_metadata information is populated, but options_len
is left to zero. F.e. in ovs, ovs_flow_key_extract() checks for
options_len before extracting the data through ip_tunnel_info_opts_get().
Geneve uses ip_tunnel_info_opts_set() helper in receive path, which
sets options_len internally, vxlan however uses ip_tunnel_info_opts(),
so when filling vxlan_metadata, we do need to update options_len.
Fixes: 4c22279848 ("ip-tunnel: Use API to access tunnel metadata options.")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the send skbuff reaches the end, nlmsg_put and friends returns
-EMSGSIZE but it is silently thrown away in ndo_fdb_dump. It is called
within a for_each_netdev loop and the first fdb entry of a following
netdev could fit in the remaining skbuff. This breaks the mechanism
of cb->args[0] and idx to keep track of the entries that are already
dumped, which results missing entries in bridge fdb show command.
Signed-off-by: Minoura Makoto <minoura@valinux.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when the packet is scrubbed early, the metadata_dst can be assigned to
the skb as soon as it is allocated. This simplifies the error cleanup path,
as the dst will be freed by kfree_skb. It is also not necessary to pass it
as a parameter to functions anymore.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when both vxlan_udp_encap_recv and vxlan_rcv are much shorter, combine
them into a single function.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code will be different for VXLAN-GPE, so move it to a separate
function. It will also make the rx path less spaghetti-like.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when the packet is scrubbed early, skb->mark can be set in the GBP
handling code.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that if UDP CSUM is not specified we will default
to enabling it. The main motivation behind this is the fact that with the
use of outer checksum we can greatly improve the performance for VXLAN
tunnels on devices that don't know how to parse tunnel headers.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In metadata mode, the vxlan interface is not supposed to use the fdb control
plane but an external one (openvswitch or static routes). With the current
code, packets may leak into the fdb handling code which usually causes them
to be dropped anyway but may have strange side effects.
Just drop the packets directly when in metadata mode if the destination data
are not correctly provided on egress.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by vxlan
as it modifies the skb on xmit.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of skb_scrub_packet was open coded in iptunnel_pull_header. Let it call
skb_scrub_packet directly instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is in preparation for iptunnel_pull_header calling skb_scrub_packet.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tun_id field in struct ip_tunnel_key is __be64, not __be32. We need to
convert the vni to tun_id correctly.
Fixes: 54bfd872bf ("vxlan: keep flags and vni in network byte order")
Reported-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For metadata based tunnels, VNI is ignored when doing vxlan device lookups
(because such tunnel receives all VNIs). However, this was not honored by
vxlan_xmit_one when doing encapsulation bypass. Move the check for metadata
based tunnel to the common place where it belongs.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there are unrecognized flags present in the vxlan header, it doesn't
make much sense to return the packet for further UDP processing, especially
considering that for other invalid flag combinations we drop the packet
because of previous checks.
This means we return positive value only at the beginning of the function
where tun_dst is not yet allocated. This allows us to get rid of the
bad_flags and error jump labels.
When we're dropping packet, we need to free tun_dst now.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring the extension handling to a single place and move the actual handling
logic out of vxlan_udp_encap_recv as much as possible.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make vxlan_udp_encap_recv shorter and more comprehensible.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Part of the parameters is not needed. Simplify the caller of this function
in preparation of making vxlan rx more comprehensible.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent repeated conversions from and to network order in the fast path.
To achieve this, define all flag constants in big endian order and store VNI
as __be32. To prevent confusion between the actual VNI value and the VNI
field from the header (which contains additional reserved byte), strictly
distinguish between "vni" and "vni_field".
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, pointer to the vxlan header is kept in a local variable. It has
to be reloaded whenever the pskb pull operations are performed which usually
happens somewhere deep in called functions.
Create a vxlan_hdr function and use it to reference the vxlan header
instead.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UDP traffic with datagram length
below MTU this give about 2% performance increase
when tunneling over ipv4 and about 60% when tunneling
over ipv6
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of UDP traffic with datagram length
below MTU this give about 3% performance increase
when tunneling over ipv4 and about 70% when
tunneling over ipv6.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
All users now pass false, so we can remove it, and remove the code that
was conditional upon it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to 4.3, openvswitch tunnel vports (vxlan, gre and geneve) could
transmit vxlan packets of any size, constrained only by the ability to
send out the resulting packets. 4.3 introduced netdevs corresponding
to tunnel vports. These netdevs have an MTU, which limits the size of
a packet that can be successfully encapsulated. The default MTU
values are low (1500 or less), which is awkwardly small in the context
of physical networks supporting jumbo frames, and leads to a
conspicuous change in behaviour for userspace.
Instead, set the MTU on openvswitch-created netdevs to be the relevant
maximum (i.e. the maximum IP packet size minus any relevant overhead),
effectively restoring the behaviour prior to 4.3.
Signed-off-by: David Wragg <david@weave.works>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the MTU of vxlan devices without an underlying device to be set
to larger values (up to a maximum based on IP packet limits and vxlan
overhead).
Previously, their MTUs could not be set to higher than the
conventional ethernet value of 1500. This is a very arbitrary value
in the context of vxlan, and prevented vxlan devices from being able
to take advantage of jumbo frames etc.
The default MTU remains 1500, for compatibility.
Signed-off-by: David Wragg <david@weave.works>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of code duplication. Factor out the duplicate code to a new
function shared between IPv4 and IPv6 xmit path.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag for tx checksumming for tunneling over IPv4 and IPv6 is different.
Decide whether to do tx checksumming in vxlan_xmit_one and pass it on as
a separate flag. This will allow for tx path consolidation in the next
patch.
Unfortunately, gcc is not clever enough to see that udp_sum is always
initialized and gives an uninitialized variable warning. Set it to false to
silence the warning.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code for output route lookup is duplicated for ndo_start_xmit and
ndo_fill_metadata_dst. Move it to a common function.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of all_zeros_mac is 6 byte, but eth_hash() will access the
8 byte, and KASan reported the below bug:
[ 8596.479031] BUG: KASan: out of bounds access in __vxlan_find_mac+0x24/0x100 at addr ffffffff841514c0
[ 8596.487647] Read of size 8 by task ip/52820
[ 8596.490818] Address belongs to variable all_zeros_mac+0x0/0x40
[ 8596.496051] CPU: 0 PID: 52820 Comm: ip Tainted: G WC 4.1.15 #1
[ 8596.503520] Hardware name: HP ProLiant DL380p Gen8, BIOS P70 02/10/2014
[ 8596.509365] ffffffff841514c0 ffff88007450f0b8 ffffffff822fa5e1 0000000000000032
[ 8596.516112] ffff88007450f150 ffff88007450f138 ffffffff812dd58c ffff88007450f1d8
[ 8596.522856] ffffffff81113b80 0000000000000282 0000000000000001 ffffffff8101ee4d
[ 8596.529599] Call Trace:
[ 8596.530858] [<ffffffff822fa5e1>] dump_stack+0x4f/0x7b
[ 8596.535080] [<ffffffff812dd58c>] kasan_report_error+0x3bc/0x3f0
[ 8596.540258] [<ffffffff81113b80>] ? __lock_acquire+0x90/0x2140
[ 8596.545245] [<ffffffff8101ee4d>] ? save_stack_trace+0x2d/0x80
[ 8596.550234] [<ffffffff812dda70>] kasan_report+0x40/0x50
[ 8596.554647] [<ffffffff81b211e4>] ? __vxlan_find_mac+0x24/0x100
[ 8596.559729] [<ffffffff812dc399>] __asan_load8+0x69/0xa0
[ 8596.564141] [<ffffffff81b211e4>] __vxlan_find_mac+0x24/0x100
[ 8596.569033] [<ffffffff81b2683d>] vxlan_fdb_create+0x9d/0x570
it can be fixed by enlarging the all_zeros_mac to 8 byte, although it is
harmless; eth_hash() will be called in other place with the memory which
is larger and equal to 8 byte.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring checksums on UDP tunnels, the flags are different
for IPv4 vs. IPv6 (and reversed). However, when lightweight tunnels
are enabled the flags used are always the IPv4 versions, which are
ignored in the IPv6 code paths. This uses the correct IPv6 flags, so
checksums can be controlled appropriately.
Fixes: a725e514 ("vxlan: metadata based tunneling for IPv6")
Fixes: abe492b4 ("geneve: UDP checksum configuration via netlink")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_main.c
drivers/net/ethernet/mellanox/mlxsw/spectrum.h
drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c
The bond_main.c and mellanox switch conflicts were cases of
overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
udp tunnel offloads tend to aggregate datagrams based on inner
headers. gro engine gets notified by tunnel implementations about
possible offloads. The match is solely based on the port number.
Imagine a tunnel bound to port 53, the offloading will look into all
DNS packets and tries to aggregate them based on the inner data found
within. This could lead to data corruption and malformed DNS packets.
While this patch minimizes the problem and helps an administrator to find
the issue by querying ip tunnel/fou, a better way would be to match on
the specific destination ip address so if a user space socket is bound
to the same address it will conflict.
Cc: Tom Herbert <tom@herbertland.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a vxlan interface is created, the driver checks that there is not
another vxlan interface with the same properties. To do this, it checks
the existing vxlan udp socket. Since commit 1c51a9159d, the creation of
the vxlan socket is done only when the interface is set up, thus it breaks
that test.
Example:
$ ip l a vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip l a vxlan11 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
$ ip -br l | grep vxlan
vxlan10 DOWN f2:55:1c:6a:fb:00 <BROADCAST,MULTICAST>
vxlan11 DOWN 7a:cb:b9:38:59:0d <BROADCAST,MULTICAST>
Instead of checking sockets, let's loop over the vxlan iface list.
Fixes: 1c51a9159d ("vxlan: fix race caused by dropping rtnl_unlock")
Reported-by: Thomas Faivre <thomas.faivre@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By moving stats update into iptunnel_xmit(), we can simplify
iptunnel_xmit() usage. With this change there is no need to
call another function (iptunnel_xmit_stats()) to update stats
in tunnel xmit code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When looking for outer IP header, use the actual socket address family, not
the address family of the default destination which is not set for metadata
based interfaces (and doesn't have to match the address family of the
received packet even if it was set).
Fix also the misleading comment.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fill the metadata correctly even when tunneling over IPv6. Also, check that
the provided metadata is of an address family that is supported by the
tunnel.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices. Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Before lightweight tunnels existed, it really didn't make sense to
create a tunnel that was not fully specified, such as without a
destination IP address - the resulting packets would go nowhere.
However, with lightweight tunnels, the opposite is true - it doesn't
make sense to require this information when it will be provided later
on by the route. This loosens the requirements for this information.
An alternative would be to allow the relaxed version only when
COLLECT_METADATA is enabled. However, since there are several
variations on this theme (such as NBMA tunnels in GRE), just dropping
the restrictions seems the most consistent across tunnels and with
the existing configuration.
CC: John Linville <linville@tuxdriver.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For metadata based vxlan interface, open both IPv4 and IPv6 socket. This is
much more user friendly: it's not necessary to create two vxlan interfaces
and pay attention to using the right one in routing rules.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make vxlan_sock_add both alloc the socket and attach it to vxlan_dev. Let
vxlan_sock_release accept vxlan_dev as its parameter instead of vxlan_sock.
This makes vxlan_sock_add and vxlan_sock release complementary. It reduces
code duplication in the next patch.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When IPv6 address is set without IPv6 configured, the vxlan socket is mostly
treated as an IPv4 one but various lookus in fdb etc. still take the
AF_INET6 into account. This creates incosistencies with weird consequences.
Just reject IPv6 addresses in such case.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vxlan_setup is called when allocating the net_device, i.e. way before
vxlan_newlink (or vxlan_dev_configure) is called. This means
vxlan->default_dst is actually unset in vxlan_setup and the condition that
sets needed_headroom always takes the else branch.
Set the needed_headrom at the point when we have the information about
the address family available.
Fixes: e4c7ed4153 ("vxlan: add ipv6 support")
Fixes: 2853af6a2e ("vxlan: use dev->needed_headroom instead of dev->hard_header_len")
CC: Cong Wang <cwang@twopensource.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/vxlan.c: In function ‘vxlan_udp_encap_recv’:
drivers/net/vxlan.c:1226: warning: ‘info’ may be used uninitialized in this function
While this warning is a false positive, it can be killed easily by
getting rid of the pointer intermediary and referring directly to the
ip_tunnel_info structure.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently tun-info options pointer is used in few cases to
pass options around. But tunnel options can be accessed using
ip_tunnel_info_opts() API without using the pointer. Following
patch removes the redundant pointer and consistently make use
of API.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default (subject to the sysctl settings), IPv6 sockets listen also for
IPv4 traffic. Vxlan is not prepared for that and expects IPv6 header in
packets received through an IPv6 socket.
In addition, it's currently not possible to have both IPv4 and IPv6 vxlan
tunnel on the same port (unless bindv6only sysctl is enabled), as it's not
possible to create and bind both IPv4 and IPv6 vxlan interfaces and there's
no way to specify both IPv4 and IPv6 remote/group IP addresses.
Set IPV6_V6ONLY on vxlan sockets to fix both of these issues. This is not
done globally in udp_tunnel, as l2tp and tipc seems to work okay when
receiving IPv4 packets on IPv6 socket and people may rely on this behavior.
The other tunnels (geneve and fou) do not support IPv6.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's currently nothing preventing directing packets with IPv6
encapsulation data to IPv4 tunnels (and vice versa). If this happens,
IPv6 addresses are incorrectly interpreted as IPv4 ones.
Track whether the given ip_tunnel_key contains IPv4 or IPv6 data. Store this
in ip_tunnel_info. Reject packets at appropriate places if they are supposed
to be encapsulated into an incompatible protocol.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mode field holds a single bit of information only (whether the
ip_tunnel_info struct is for rx or tx). Change the mode field to bit flags.
This allows more mode flags to be added.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce function udp_tun_rx_dst() to initialize tunnel dst on
receive path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before 56ef9c909b40[1] it used to ignore all errors from igmp_join().
That commit enhanced that and made it error out whatever error happened
with igmp_join(), but that's not good because when using multicast
groups vxlan will try to join it multiple times if the socket is reused
and then the 2nd and further attempts will fail with EADDRINUSE.
As we don't track to which groups the socket is already subscribed, it's
okay to just ignore that error.
Fixes: 56ef9c909b ("vxlan: Move socket initialization to within rtnl scope")
Reported-by: John Nielsen <lists@jnielsen.net>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add calls to gro_cells infrastructure to do GRO when receiving on a tunnel.
Testing:
Ran 200 netperf TCP_STREAM instance
- With fix (GRO enabled on VXLAN interface)
Verify GRO is happening.
9084 MBps tput
3.44% CPU utilization
- Without fix (GRO disabled on VXLAN interface)
Verified no GRO is happening.
9084 MBps tput
5.54% CPU utilization
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The remote checksum offload GRO did not consider the case that frag0
might be in use. This patch fixes that by accessing headers using the
skb_gro functions and not saving offsets relative to skb->head.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support metadata based (formerly flow based) tunneling also for IPv6.
This complements commit ee122c79d4 ("vxlan: Flow based tunneling").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'flags' variable is already defined in the outer scope.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the lwtunnel state resides in per-protocol data. This is
a problem if we encapsulate ipv6 traffic in an ipv4 tunnel (or vice versa).
The xmit function of the tunnel does not know whether the packet has been
routed to it by ipv4 or ipv6, yet it needs the lwtstate data. Moving the
lwtstate data to dst_entry makes such inter-protocol tunneling possible.
As a bonus, this brings a nice diffstat.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the ipv4_tos and ipv4_ttl fields to just 'tos' and 'ttl', as they'll
be used with IPv6 tunnels, too.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the IPv6 addresses as an union with IPv4 ones. When using IPv4, the
newly introduced padding after the IPv4 addresses needs to be zeroed out.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When too many remotes are bound to an FDB entry, index may not be increased.
This problem will be caused on the large scale environment that is based on
the unicast default destination, for instance.
Signed-off-by: Atzm Watanabe <atzm@iij.ad.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
IFLA_VXLAN_FLOWBASED is useless without IFLA_VXLAN_COLLECT_METADATA,
so combine them into single IFLA_VXLAN_COLLECT_METADATA flag.
'flowbased' doesn't convey real meaning of the vxlan tunnel mode.
This mode can be used by routing, tc+bpf and ovs.
Only ovs is strictly flow based, so 'collect metadata' is a better
name for this tunnel mode.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two vxlan driver flags FLOWBASED and COLLECT_METADATA need to be set to
make use of its new flow mode. The former already exposed. Expose the latter.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds net argument to ipv6_stub_impl.ipv6_dst_lookup
for use cases where sk is not available (like mpls).
sk appears to be needed to get the namespace 'net' and is optional
otherwise. This patch series changes ipv6_stub_impl.ipv6_dst_lookup
to take net argument. sk remains optional.
All callers of ipv6_stub_impl.ipv6_dst_lookup have been modified
to pass net. I have modified them to use already available
'net' in the scope of the call. I can change them to
sock_net(sk) to avoid any unintended change in behaviour if sock
namespace is different. They dont seem to be from code inspection.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Silences the following sparse warnings:
drivers/net/vxlan.c:1818:21: warning: incorrect type in assignment (different base types)
drivers/net/vxlan.c:1818:21: expected restricted __be32 [usertype] vx_vni
drivers/net/vxlan.c:1818:21: got unsigned int [unsigned] [usertype] vni
drivers/net/vxlan.c:2014:58: warning: incorrect type in argument 11 (different base types)
drivers/net/vxlan.c:2014:58: expected unsigned int [unsigned] [usertype] vni
drivers/net/vxlan.c:2014:58: got restricted __be32 [usertype] <noident>
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets rid of all OVS specific VXLAN code in the receive and
transmit path by using a VXLAN net_device to represent the vport.
Only a small shim layer remains which takes care of handling the
VXLAN specific OVS Netlink configuration.
Unexports vxlan_sock_add(), vxlan_sock_release(), vxlan_xmit_skb()
since they are no longer needed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This factors out the device configuration out of the RTNL newlink
API which allows for in-kernel creation of VXLAN net_devices.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This add the ability to select a routing table based on the tunnel
id which allows to maintain separate routing tables for each virtual
tunnel network.
ip rule add from all tunnel-id 100 lookup 100
ip rule add from all tunnel-id 200 lookup 200
A new static key controls the collection of metadata at tunnel level
upon demand.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces a new IP tunnel lightweight tunnel type which allows
to specify IP tunnel instructions per route. Only IPv4 is supported
at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allows putting a VXLAN device into a new flow-based mode in which
skbs with a ip_tunnel_info dst metadata attached will be encapsulated
according to the instructions stored in there with the VXLAN device
defaults taken into consideration.
Similar on the receive side, if the VXLAN_F_COLLECT_METADATA flag is
set, the packet processing will populate a ip_tunnel_info struct for
each packet received and attach it to the skb using the new metadata
dst. The metadata structure will contain the outer header and tunnel
header fields which have been stripped off. Layers further up in the
stack such as routing, tc or netfitler can later match on these fields
and perform forwarding. It is the responsibility of upper layers to
ensure that the flag is set if the metadata is needed. The flag limits
the additional cost of metadata collecting based on demand.
This prepares the VXLAN device to be steered by the routing and other
subsystems which allows to support encapsulation for a large number
of tunnel endpoints and tunnel ids through a single net_device which
improves the scalability.
It also allows for OVS to leverage this mode which in turn allows for
the removal of the OVS specific VXLAN code.
Because the skb is currently scrubed in vxlan_rcv(), the attachment of
the new dst metadata is postponed until after scrubing which requires
the temporary addition of a new member to vxlan_metadata. This member
is removed again in a later commit after the indirect VXLAN receive API
has been removed.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__vxlan_find_mac invokes ether_addr_equal on the eth_addr field,
which triggers unaligned access messages, so rearrange vxlan_fdb
to avoid this in the most non-intrusive way.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're seeing some softlockups from this function when there
are a lot fdb entries on a vxlan device. Taking the lock for
each bucket instead of the whole table is enough to fix that.
Signed-off-by: Sorin Dumitru <sdumitru@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
By inspection, this appears to be a typo. The gating comparison
involves vxlan->dev rather than dev. In fact, dev is the iterator in
the preceding loop above but it is actually constant in the 2nd loop.
Use of dev seems to be a bad cut-n-paste from the prior call to
unregister_netdevice_queue. Change dev to vxlan->dev, since that is
what is actually being checked.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a following commit, a new function will be introduced to only lookup for
a nsid (no allocation if the nsid doesn't exist). To avoid confusion, the
existing function is renamed.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VXLAN must provide the skb mark and specifiy IPPROTO_UDP when doing
the FIB lookup for the remote ip. Otherwise an invalid route might
be returned.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value of vxlan_fdb_replace always is greater than or equal to 0
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac-socfpga.c conflict was a case of a bug fix overlapping
changes in net-next to handle an error pointer differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
handle_offloads() calls skb_reset_inner_headers() to store
the layer pointers to the encapsulated packet. However, we
currently push the vlag tag (if there is one) onto the packet
afterwards. This changes the MAC header for the encapsulated
packet but it is not reflected in skb->inner_mac_header, which
breaks GSO and drivers which attempt to use this for encapsulation
offloads.
Fixes: 1eaa8178 ("vxlan: Add tx-vlan offload support.")
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 79b16aadea
("udp_tunnel: Pass UDP socket down through udp_tunnel{, 6}_xmit_skb()")
introduce 'sk' but we already have one inner 'sk'.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Those are counterparts to nla_put_in_addr and nla_put_in6_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some lines in vxlan code are indented by 7 spaces instead of a tab.
Fixes: e4c7ed4153 ("vxlan: add ipv6 support")
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dan Carpenter's static checker warned that in vxlan_stop we are checking
if 'vs' can be NULL while later we simply derreference it.
As after commit 56ef9c909b ("vxlan: Move socket initialization to
within rtnl scope") 'vs' just cannot be NULL in vxlan_stop() anymore, as
the interface won't go up if the socket initialization fails. So we are
good to just remove the check and make it consistent.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Test robot noticed that we check the return of vxlan_igmp_join and leave
but inside them there was a path that it could be used initialized.
It's not really possible because those if() inside these igmp functions
would always match as we can't have sockets of other type in there, but
this way we keep the compiler happy.
Fixes: 56ef9c909b ("vxlan: Move socket initialization to within rtnl scope")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if a multicast join operation fail, the vxlan interface will
be UP but not functional, without even a log message informing the user.
Now that we can grab socket lock after already having rntl, we don't
need to defer socket creation and multicast operations. By not deferring
we can do proper error reporting to the user through ip exit code.
This patch thus removes all deferred work that vxlan had and put it back
inline. Now the socket will only be created, bound and join multicast
group when one bring the interface up, and will undo all that as soon as
one put the interface down.
As vxlan_sock_hold() is not used after this patch, it was removed too.
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in favor of their inner __ ones, which doesn't grab rtnl.
As these functions need to operate on a locked socket, we can't be
grabbing rtnl by then. It's too late and doing so causes reversed
locking.
So this patch:
- move rtnl handling to callers instead while already fixing some
reversed locking situations, like on vxlan and ipvs code.
- renames __ ones to not have the __ mark:
__ip_mc_{join,leave}_group -> ip_mc_{join,leave}_group
__ipv6_sock_mc_{join,drop} -> ipv6_sock_mc_{join,drop}
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit dfd8645ea1 wrongly assumes that VXLAN_VDI_MASK includes
eight lower order reserved bits of VNI field that are using for remote
checksum offload.
Right now, when VNI number greater then 0xffff, vxlan_udp_encap_recv()
will always return with 'bad_flag' error, reducing the usable vni range
from 0..16777215 to 0..65535. Also, it doesn't really check whether RCO
bits processed or not.
Fix it by adding new VNI mask which has all 32 bits of VNI field:
24 bits for id and 8 bits for other usage.
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of AF_INET s_addr was set to INADDR_ANY (0) which which both
symmetric with the AF_INET6 case, where s_addr is not set, and unnecessary
as udp_conf is zeroed out earlier in the same function.
I suspect this change does not have any run-time effect due to compiler
optimisations. But it does make the code a little easier on the/my eyes.
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change remote checksum handling to set checksum partial as default
behavior. Added an iflink parameter to configure not using
checksum partial (calling csum_partial to update checksum).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds infrastructure so that remote checksum offload can
set CHECKSUM_PARTIAL instead of calling csum_partial and writing
the modfied checksum field.
Add skb_remcsum_adjust_partial function to set an skb for using
CHECKSUM_PARTIAL with remote checksum offload. Changed
skb_remcsum_process and skb_gro_remcsum_process to take a boolean
argument to indicate if checksum partial can be set or the
checksum needs to be modified using the normal algorithm.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remote checksum offload processing is currently the same for both
the GRO and non-GRO path. When the remote checksum offload option
is encountered, the checksum field referred to is modified in
the packet. So in the GRO case, the packet is modified in the
GRO path and then the operation is skipped when the packet goes
through the normal path based on skb->remcsum_offload. There is
a problem in that the packet may be modified in the GRO path, but
then forwarded off host still containing the remote checksum option.
A remote host will again perform RCO but now the checksum verification
will fail since GRO RCO already modified the checksum.
To fix this, we ensure that GRO restores a packet to it's original
state before returning. In this model, when GRO processes a remote
checksum option it still changes the checksum per the algorithm
but on return from lower layer processing the checksum is restored
to its original value.
In this patch we add define gro_remcsum structure which is passed
to skb_gro_remcsum_process to save offset and delta for the checksum
being changed. After lower layer processing, skb_gro_remcsum_cleanup
is called to restore the checksum before returning from GRO.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
src_ip is a pointer to a union vxlan_addr, one member of which is a
struct sockaddr. Passing a pointer to src_ip is wrong; one should pass
the value of src_ip itself. Since %pIS formally expects something of
type struct sockaddr*, let's pass a pointer to the appropriate union
member, though this of course doesn't change the generated code.
Fixes: e4c7ed4153 ("vxlan: add ipv6 support")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows for a VXLAN-GBP socket to talk to a Linux VXLAN socket by
not setting any of the bits.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds skb_remcsum_process and skb_gro_remcsum_process to
perform the appropriate adjustments to the skb when receiving
remote checksum offload.
Updated vxlan and gue to use these functions.
Tested: Ran TCP_RR and TCP_STREAM netperf for VXLAN and GUE, did
not see any change in performance.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the netns to src_net to avoid confusion with the netns where the
interface stands. The user may specify IFLA_NET_NS_[PID|FD] to create
a x-netns netndevice: IFLA_NET_NS_[PID|FD] points to the netns where the
netdevice stands and src_net to the link netns.
Note that before commit f01ec1c017 ("vxlan: add x-netns support"), it was
possible to create a x-netns vxlan netdevice, but the netdevice was not
operational.
Fixes: f01ec1c017 ("vxlan: add x-netns support")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous commit is based on a wrong assumption, fdb messages are always sent
into the netns where the interface stands (see vxlan_fdb_notify()).
These fdb messages doesn't embed the rtnl attribute IFLA_LINK_NETNSID, thus we
need to add it (useful to interpret NDA_IFINDEX or NDA_DST for example).
Note also that vxlan_nlmsg_size() was not updated.
Fixes: 193523bf93 ("vxlan: advertise netns of vxlan dev in fdb msg")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the vxlan transmit path there is no need to reference the socket
for a tunnel which is needed for the receive side. We do, however,
need the vxlan_dev flags. This patch eliminate references
to the socket in the transmit path, and changes VXLAN_F_UNSHAREABLE
to be VXLAN_F_RCV_FLAGS. This mask is used to store the flags
applicable to receive (GBP, CSUM6_RX, and REMCSUM_RX) in the
vxlan_sock flags.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP tunnel transmit functions udp_tunnel_xmit_skb and
udp_tunnel6_xmit_skb include a socket argument. The socket being
passed to the functions (from VXLAN) is a UDP created for receive
side. The only thing that the socket is used for in the transmit
functions is to get the setting for checksum (enabled or zero).
This patch removes the argument and and adds a nocheck argument
for checksum setting. This eliminates the unnecessary dependency
on a UDP socket for UDP tunnel transmit.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink FDB messages are sent in the link netns. The header of these messages
contains the ifindex (ndm_ifindex) of the netdevice, but this ifindex is
unusable in case of x-netns vxlan.
I named the new attribute NDA_NDM_IFINDEX_NETNSID, to avoid confusion with
NDA_IFINDEX.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Contrary to common expectations for an "int" return, these functions
return only a positive value -- if used correctly they cannot even
return 0 because the message header will necessarily be in the skb.
This makes the very common pattern of
if (genlmsg_end(...) < 0) { ... }
be a whole bunch of dead code. Many places also simply do
return nlmsg_end(...);
and the caller is expected to deal with it.
This also commonly (at least for me) causes errors, because it is very
common to write
if (my_function(...))
/* error condition */
and if my_function() does "return nlmsg_end()" this is of course wrong.
Additionally, there's not a single place in the kernel that actually
needs the message length returned, and if anyone needs it later then
it'll be very easy to just use skb->len there.
Remove this, and make the functions void. This removes a bunch of dead
code as described above. The patch adds lines because I did
- return nlmsg_end(...);
+ nlmsg_end(...);
+ return 0;
I could have preserved all the function's return values by returning
skb->len, but instead I've audited all the places calling the affected
functions and found that none cared. A few places actually compared
the return value with <= 0 in dump functionality, but that could just
be changed to < 0 with no change in behaviour, so I opted for the more
efficient version.
One instance of the error I've made numerous times now is also present
in net/phonet/pn_netlink.c in the route_dumpit() function - it didn't
check for <0 or <=0 and thus broke out of the loop every single time.
I've preserved this since it will (I think) have caused the messages to
userspace to be formatted differently with just a single message for
every SKB returned to userspace. It's possible that this isn't needed
for the tools that actually use this, but I don't even know what they
are so couldn't test that changing this behaviour would be acceptable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A VXLAN net_device looking for an appropriate socket may only consider
a socket which has a matching set of flags/extensions enabled. If
incompatible flags are enabled, return a conflict to have the caller
create a distinct socket with distinct port.
The OVS VXLAN port is kept unaware of extensions at this point.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements supports for the Group Policy VXLAN extension [0] to provide
a lightweight and simple security label mechanism across network peers
based on VXLAN. The security context and associated metadata is mapped
to/from skb->mark. This allows further mapping to a SELinux context
using SECMARK, to implement ACLs directly with nftables, iptables, OVS,
tc, etc.
The group membership is defined by the lower 16 bits of skb->mark, the
upper 16 bits are used for flags.
SELinux allows to manage label to secure local resources. However,
distributed applications require ACLs to implemented across hosts. This
is typically achieved by matching on L2-L4 fields to identify the
original sending host and process on the receiver. On top of that,
netlabel and specifically CIPSO [1] allow to map security contexts to
universal labels. However, netlabel and CIPSO are relatively complex.
This patch provides a lightweight alternative for overlay network
environments with a trusted underlay. No additional control protocol
is required.
Host 1: Host 2:
Group A Group B Group B Group A
+-----+ +-------------+ +-------+ +-----+
| lxc | | SELinux CTX | | httpd | | VM |
+--+--+ +--+----------+ +---+---+ +--+--+
\---+---/ \----+---/
| |
+---+---+ +---+---+
| vxlan | | vxlan |
+---+---+ +---+---+
+------------------------------+
Backwards compatibility:
A VXLAN-GBP socket can receive standard VXLAN frames and will assign
the default group 0x0000 to such frames. A Linux VXLAN socket will
drop VXLAN-GBP frames. The extension is therefore disabled by default
and needs to be specifically enabled:
ip link add [...] type vxlan [...] gbp
In a mixed environment with VXLAN and VXLAN-GBP sockets, the GBP socket
must run on a separate port number.
Examples:
iptables:
host1# iptables -I OUTPUT -m owner --uid-owner 101 -j MARK --set-mark 0x200
host2# iptables -I INPUT -m mark --mark 0x200 -j DROP
OVS:
# ovs-ofctl add-flow br0 'in_port=1,actions=load:0x200->NXM_NX_TUN_GBP_ID[],NORMAL'
# ovs-ofctl add-flow br0 'in_port=2,tun_gbp_id=0x200,actions=drop'
[0] https://tools.ietf.org/html/draft-smith-vxlan-group-policy
[1] http://lwn.net/Articles/204905/
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for remote checksum offload in VXLAN. This uses a
reserved bit to indicate that RCO is being done, and uses the low order
reserved eight bits of the VNI to hold the start and offset values in a
compressed manner.
Start is encoded in the low order seven bits of VNI. This is start >> 1
so that the checksum start offset is 0-254 using even values only.
Checksum offset (transport checksum field) is indicated in the high
order bit in the low order byte of the VNI. If the bit is set, the
checksum field is for UDP (so offset = start + 6), else checksum
field is for TCP (so offset = start + 16). Only TCP and UDP are
supported in this implementation.
Remote checksum offload for VXLAN is described in:
https://tools.ietf.org/html/draft-herbert-vxlan-rco-00
Tested by running 200 TCP_STREAM connections with VXLAN (over IPv4).
With UDP checksums and Remote Checksum Offload
IPv4
Client
11.84% CPU utilization
Server
12.96% CPU utilization
9197 Mbps
IPv6
Client
12.46% CPU utilization
Server
14.48% CPU utilization
8963 Mbps
With UDP checksums, no remote checksum offload
IPv4
Client
15.67% CPU utilization
Server
14.83% CPU utilization
9094 Mbps
IPv6
Client
16.21% CPU utilization
Server
14.32% CPU utilization
9058 Mbps
No UDP checksums
IPv4
Client
15.03% CPU utilization
Server
23.09% CPU utilization
9089 Mbps
IPv6
Client
16.18% CPU utilization
Server
26.57% CPU utilization
8954 Mbps
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces udp_offload_callbacks which has the same
GRO functions (but not a GSO function) as offload_callbacks,
except there is an argument to a udp_offload struct passed to
gro_receive and gro_complete functions. This additional argument
can be used to retrieve the per port structure of the encapsulation
for use in gro processing (mostly by doing container_of on the
structure).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the header flags of VXLAN in anticipation of
defining some new ones:
- Move header related definitions from vxlan.c to vxlan.h
- Change VXLAN_FLAGS to be VXLAN_HF_VNI (only currently defined flag)
- Move check for unknown flags to after we find vxlan_sock, this
assumes that some flags may be processed based on tunnel
configuration
- Add a comment about why the stack treating unknown set flags as an
error instead of ignoring them
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the only tunnel protocol that supports GRO with encapsulated
Ethernet is VXLAN. This pulls out the Ethernet code into a proper layer
so that it can be used by other tunnel protocols such as GRE and Geneve.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error vxlan_xmit_one() can free already freed skb.
Also fixes memory leak of dst-entry.
Fixes: acbf74a763 ("vxlan: Refactor vxlan driver to make use
of the common UDP tunnel functions").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when trying to reuse a socket, vxlan_sock_add will grab
vn->sock_lock, locate a reusable socket, inc refcount and release
vn->sock_lock.
But vxlan_sock_release() will first decrement refcount, and then grab
that lock. refcnt operations are atomic but as currently we have
deferred works which hold vs->refcnt each, this might happen, leading to
a use after free (specially after vxlan_igmp_leave):
CPU 1 CPU 2
deferred work vxlan_sock_add
... ...
spin_lock(&vn->sock_lock)
vs = vxlan_find_sock();
vxlan_sock_release
dec vs->refcnt, reaches 0
spin_lock(&vn->sock_lock)
vxlan_sock_hold(vs), refcnt=1
spin_unlock(&vn->sock_lock)
hlist_del_rcu(&vs->hlist);
vxlan_notify_del_rx_port(vs)
spin_unlock(&vn->sock_lock)
So when we look for a reusable socket, we check if it wasn't freed
already before reusing it.
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Fixes: 7c47cedf43 ("vxlan: move IGMP join/leave to work queue")
Signed-off-by: David S. Miller <davem@davemloft.net>
Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In "vxlan: Call udp_sock_create" there was a logic error that resulted in
the default for IPv6 VXLAN tunnels going from using checksums to not using
checksums. Since there is currently no support in iproute2 for setting
these values it means that a kernel after the change cannot talk over a IPv6
VXLAN tunnel to a kernel prior the change.
Fixes: 3ee64f3 ("vxlan: Call udp_sock_create")
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use them to push skb->vlan_tci into the payload and avoid code
duplication.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name fits better. Plus there's going to be introduced
__vlan_insert_tag later on.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most NICs that report NETIF_F_GSO_UDP_TUNNEL support VXLAN, and not
other UDP-based encapsulation protocols where the format and size of the
header differs. This patch implements a generic ndo_gso_check() for
VXLAN which will only advertise GSO support when the skb looks like it
contains VXLAN (or no UDP tunnelling at all).
Implementation shamelessly stolen from Tom Herbert:
http://thread.gmane.org/gmane.linux.network/332428/focus=333111
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/chelsio/cxgb4vf/sge.c
drivers/net/ethernet/intel/ixgbe/ixgbe_phy.c
sge.c was overlapping two changes, one to use the new
__dev_alloc_page() in net-next, and one to use s->fl_pg_order in net.
ixgbe_phy.c was a set of overlapping whitespace changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, we only match against local port number in order to reuse
socket. But if this new vxlan wants an IPv6 socket and a IPv4 one bound
to that port, vxlan will reuse an IPv4 socket as IPv6 and a panic will
follow. The following steps reproduce it:
# ip link add vxlan6 type vxlan id 42 group 229.10.10.10 \
srcport 5000 6000 dev eth0
# ip link add vxlan7 type vxlan id 43 group ff0e::110 \
srcport 5000 6000 dev eth0
# ip link set vxlan6 up
# ip link set vxlan7 up
<panic>
[ 4.187481] BUG: unable to handle kernel NULL pointer dereference at 0000000000000058
...
[ 4.188076] Call Trace:
[ 4.188085] [<ffffffff81667c4a>] ? ipv6_sock_mc_join+0x3a/0x630
[ 4.188098] [<ffffffffa05a6ad6>] vxlan_igmp_join+0x66/0xd0 [vxlan]
[ 4.188113] [<ffffffff810a3430>] process_one_work+0x220/0x710
[ 4.188125] [<ffffffff810a33c4>] ? process_one_work+0x1b4/0x710
[ 4.188138] [<ffffffff810a3a3b>] worker_thread+0x11b/0x3a0
[ 4.188149] [<ffffffff810a3920>] ? process_one_work+0x710/0x710
So address family must also match in order to reuse a socket.
Reported-by: Jean-Tsung Hsiao <jhsiao@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing GRO processing for UDP tunnels, we never add
SKB_GSO_UDP_TUNNEL to gso_type - only the type of the inner protocol
is added (such as SKB_GSO_TCPV4). The result is that if the packet is
later resegmented we will do GSO but not treat it as a tunnel. This
results in UDP fragmentation of the outer header instead of (i.e.) TCP
segmentation of the inner header as was originally on the wire.
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add definition to vxlan nla_policy for UDP checksum. This is necessary
to enable UDP checksums on VXLAN.
In some instances, enabling UDP checksums can improve performance on
receive for devices that return legacy checksum-unnecessary for UDP/IP.
Also, UDP checksum provides some protection against VNI corruption.
Testing:
Ran 200 instances of TCP_STREAM and TCP_RR on bnx2x.
TCP_STREAM
IPv4, without UDP checksums
14.41% TX CPU utilization
25.71% RX CPU utilization
9083.4 Mbps
IPv4, with UDP checksums
13.99% TX CPU utilization
13.40% RX CPU utilization
9095.65 Mbps
TCP_RR
IPv4, without UDP checksums
94.08% TX CPU utilization
156/248/462 90/95/99% latencies
1.12743e+06 tps
IPv4, with UDP checksums
94.43% TX CPU utilization
158/250/462 90/95/99% latencies
1.13345e+06 tps
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull maybe change skb->data and make eth pointer oboslete,
so eth needs to reload
Fixes: 91269e390d ("vxlan: using pskb_may_pull as early as possible")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull should be used to check if skb->data has enough space,
skb->len can not ensure that.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when netif_rx() is done, the netif_rx handled skb maybe be freed,
and should not be used.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_protocol to set inner Ethernet protocol to
ETH_P_TEB before transmit. This is needed for GSO with UDP tunnels.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit acbf74a763 ("vxlan: Refactor vxlan driver to make use of the common UDP tunnel functions." introduced a bug in vxlan_xmit_one()
function, causing it to transmit Vxlan packets without proper
Vxlan header inserted. The change was not needed in the first
place. Revert it.
Reported-by: Tom Herbert <therbert@google.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify vxlan implementation using common UDP tunnel APIs.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch:
- Clarifies the specific requirements of devices returning
CHECKSUM_UNNECESSARY (comments in skbuff.h).
- Adds csum_level field to skbuff. This is used to express how
many checksums are covered by CHECKSUM_UNNECESSARY (stores n - 1).
This replaces the overloading of skb->encapsulation, that field is
is now only used to indicate inner headers are valid.
- Change __skb_checksum_validate_needed to "consume" each checksum
as indicated by csum_level as layers of the the packet are parsed.
- Remove skb_pop_rcv_encapsulation, no longer needed in the new
csum_level model.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first initializer in the following
union vxlan_addr ipa = {
.sin.sin_addr.s_addr = tip,
.sa.sa_family = AF_INET,
};
is optimised away by the compiler, due to the second initializer,
therefore initialising .sin.sin_addr.s_addr always to 0.
This results in netlink messages indicating a L3 miss never contain the
missed IP address. This was observed with GCC 4.8 and 4.9. I do not know about previous versions.
The problem affects user space programs relying on an IP address being
sent as part of a netlink message indicating a L3 miss.
Changing
.sa.sa_family = AF_INET,
to
.sin.sin_family = AF_INET,
fixes the problem.
Signed-off-by: Gerhard Stenzel <gerhard.stenzel@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndm_type means L3 address type, in neighbour proxy and vxlan, it's RTN_UNICAST.
NDA_DST is for netlink TLV type, hence it's not right value in this context.
Signed-off-by: Jun Zhao <mypopydev@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxlan driver call common function udp_sock_create to create the
listener UDP port.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dumping a bridge fdb dumps every fdb entry
held. With this change we are going to filter
on selected bridge port.
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxlan and OVS vport-vxlan call common function to get source port
for a UDP tunnel. Removed vxlan_src_port since the functionality is
now in udp_flow_src_port.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_pop_rcv_encapsulation and postpull_rcsum for the Ethernet
header to work properly with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we mirror packets from a vxlan tunnel to other device,
the mirror device should see the same packets (that is, without
outer header). Because vxlan tunnel sets dev->hard_header_len,
tcf_mirred() resets mac header back to outer mac, the mirror device
actually sees packets with outer headers
Vxlan tunnel should set dev->needed_headroom instead of
dev->hard_header_len, like what other ip tunnels do. This fixes
the above problem.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: stephen hemminger <stephen@networkplumber.org>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to gro_postpull_rcsum for GRO to work with checksum complete.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added VXLAN link configuration for sending UDP checksums, and allowing
TX and RX of UDP6 checksums.
Also, call common iptunnel_handle_offloads and added GSO support for
checksums.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows to switch the netns when packet is encapsulated or
decapsulated.
The vxlan socket is openned into the i/o netns, ie into the netns where
encapsulated packets are received. The socket lookup is done into this netns to
find the corresponding vxlan tunnel. After decapsulation, the packet is
injecting into the corresponding interface which may stand to another netns.
When one of the two netns is removed, the tunnel is destroyed.
Configuration example:
ip netns add netns1
ip netns exec netns1 ip link set lo up
ip link add vxlan10 type vxlan id 10 group 239.0.0.10 dev eth0 dstport 0
ip link set vxlan10 netns netns1
ip netns exec netns1 ip addr add 192.168.0.249/24 broadcast 192.168.0.255 dev vxlan10
ip netns exec netns1 ip link set vxlan10 up
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goal of this patch is to fix rtnelink notification. The main problem was
about notification for fdb entry with more than one remote. Before the patch,
when a remote was added to an existing fdb entry, the kernel advertised the
first remote instead of the added one. Also when a remote was removed from a fdb
entry with several remotes, the deleted remote was not advertised.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the dst->output() path for ipv4, the code assumes the skb it has to
transmit is attached to an inet socket, specifically via
ip_mc_output() : The sk_mc_loop() test triggers a WARN_ON() when the
provider of the packet is an AF_PACKET socket.
The dst->output() method gets an additional 'struct sock *sk'
parameter. This needs a cascade of changes so that this parameter can
be propagated from vxlan to final consumer.
Fixes: 8f646c922d ("vxlan: keep original skb ownership")
Reported-by: lucien xin <lucien.xin@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The VXLAN neigh_reduce() code is completely non-functional since
check-in. Specific errors:
1) The original code drops all packets with a multicast destination address,
even though neighbor solicitations are sent to the solicited-node
address, a multicast address. The code after this check was never run.
2) The neighbor table lookup used the IPv6 header destination, which is the
solicited node address, rather than the target address from the
neighbor solicitation. So neighbor lookups would always fail if it
got this far. Also for L3MISSes.
3) The code calls ndisc_send_na(), which does a send on the tunnel device.
The context for neigh_reduce() is the transmit path, vxlan_xmit(),
where the host or a bridge-attached neighbor is trying to transmit
a neighbor solicitation. To respond to it, the tunnel endpoint needs
to do a *receive* of the appropriate neighbor advertisement. Doing a
send, would only try to send the advertisement, encapsulated, to the
remote destinations in the fdb -- hosts that definitely did not do the
corresponding solicitation.
4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the
isrouter flag in the advertisement. This has nothing to do with whether
or not the target is a router, and generally won't be set since the
tunnel endpoint is bridging, not routing, traffic.
The patch below creates a proxy neighbor advertisement to respond to
neighbor solicitions as intended, providing proper IPv6 support for neighbor
reduction.
Signed-off-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a NULL pointer dereference in the event of an
skb allocation failure in arp_reduce().
Signed-Off-By: David L Stevens <dlstevens@us.ibm.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The loop in vxlan_gro_receive() over the current set of candidates for
coalescing was wrongly aborted once a match was found. In rare cases,
this can cause a false-positives matching in the next layer GRO checks.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the practice set by commit 0afb166 "vxlan: Add capability
of Rx checksum offload for inner packet" is applied when the skb
goes through the portion of the RX code which is shared between
vxlan netdevices and ovs vxlan port instances.
Cc: Joseph Gasparakis <joseph.gasparakis@intel.com>
Cc: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per suggestion from Eric W. Biederman, vxlan should be using
{un,}register_pernet_subsys() instead of {un,}register_pernet_device()
to ensure the vxlan_net structure is initialized before and cleaned
up after all network devices in a given network namespace i.e. when
dealing with network notifiers. This is similarly handeled already in
commit 91e2ff3528 ("net: Teach vlans to cleanup as a pernet subsystem")
and, thus, improves upon fd27e0d44a ("net: vxlan: do not use vxlan_net
before checking event type"). Just as in 91e2ff3528, we do not need
to explicitly handle deletion of vxlan devices as network namespace
exit calls dellink on all remaining virtual devices, and
rtnl_link_unregister() calls dellink on all outstanding devices in that
network namespace, so we can entirely drop the pernet exit operation
as well. Moreover, on vxlan module exit, rcu_barrier() is called by
netns since commit 3a765edadb ("netns: Add an explicit rcu_barrier
to unregister_pernet_{device|subsys}"), so this may be omitted. Tested
with various scenarios and works well on my side.
Suggested-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a description to the vxlan module, helping save the world
from the minions of destruction and confusion.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Brandeburg reported that commit acaf4e7099 caused a panic
when adding a network namespace while vxlan module was present in
the system:
[<ffffffff814d0865>] vxlan_lowerdev_event+0xf5/0x100
[<ffffffff816e9e5d>] notifier_call_chain+0x4d/0x70
[<ffffffff810912be>] __raw_notifier_call_chain+0xe/0x10
[<ffffffff810912d6>] raw_notifier_call_chain+0x16/0x20
[<ffffffff815d9610>] call_netdevice_notifiers_info+0x40/0x70
[<ffffffff815d9656>] call_netdevice_notifiers+0x16/0x20
[<ffffffff815e1bce>] register_netdevice+0x1be/0x3a0
[<ffffffff815e1dce>] register_netdev+0x1e/0x30
[<ffffffff814cb94a>] loopback_net_init+0x4a/0xb0
[<ffffffffa016ed6e>] ? lockd_init_net+0x6e/0xb0 [lockd]
[<ffffffff815d6bac>] ops_init+0x4c/0x150
[<ffffffff815d6d23>] setup_net+0x73/0x110
[<ffffffff815d725b>] copy_net_ns+0x7b/0x100
[<ffffffff81090e11>] create_new_namespaces+0x101/0x1b0
[<ffffffff81090f45>] copy_namespaces+0x85/0xb0
[<ffffffff810693d5>] copy_process.part.26+0x935/0x1500
[<ffffffff811d5186>] ? mntput+0x26/0x40
[<ffffffff8106a15c>] do_fork+0xbc/0x2e0
[<ffffffff811b7f2e>] ? ____fput+0xe/0x10
[<ffffffff81089c5c>] ? task_work_run+0xac/0xe0
[<ffffffff8106a406>] SyS_clone+0x16/0x20
[<ffffffff816ee689>] stub_clone+0x69/0x90
[<ffffffff816ee329>] ? system_call_fastpath+0x16/0x1b
Apparently loopback device is being registered first and thus we
receive an event notification when vxlan_net is not ready. Hence,
when we call net_generic() and request vxlan_net_id, we seem to
access garbage at that point in time. In setup_net() where we set
up a newly allocated network namespace, we traverse the list of
pernet ops ...
list_for_each_entry(ops, &pernet_list, list) {
error = ops_init(ops, net);
if (error < 0)
goto out_undo;
}
... and loopback_net_init() is invoked first here, so in the middle
of setup_net() we get this notification in vxlan. As currently we
only care about devices that unregister, move access through
net_generic() there. Fix is based on Cong Wang's proposal, but
only changes what is needed here. It sucks a bit as we only work
around the actual cure: right now it seems the only way to check if
a netns actually finished traversing all init ops would be to check
if it's part of net_namespace_list. But that I find quite expensive
each time we go through a notifier callback. Anyway, did a couple
of tests and it seems good for now.
Fixes: acaf4e7099 ("net: vxlan: when lower dev unregisters remove vxlan dev as well")
Reported-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Tested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use vxlan_dellink() handler in vxlan_exit_net(), since
i) we're not in fast-path and we should be consistent in dismantle
just as we would remove a device through rtnl ops, and more
importantly, ii) in case future code will kfree() memory in
vxlan_dellink(), we would leak it right here unnoticed. Therefore,
do not only half of the cleanup work, but make it properly.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can create a vxlan device with an explicit underlying carrier.
In that case, when the carrier link is being deleted from the
system (e.g. due to module unload) we should also clean up all
created vxlan devices on top of it since otherwise we're in an
inconsistent state in vxlan device. In that case, the user needs
to remove all such devices, while in case of other virtual devs
that sit on top of physical ones, it is usually the case that
these devices do unregister automatically as well and do not
leave the burden on the user.
This work is not necessary when vxlan device was not created with
a real underlying device, as connections can resume in that case
when driver is plugged again. But at least for the other cases,
we should go ahead and do the cleanup on removal.
We don't register the notifier during vxlan_newlink() here since
I consider this event rather rare, and therefore we should not
bloat vxlan's core structure unecessary. Also, we can simply make
use of unregister_netdevice_many() to batch that. fdb is flushed
upon ndo_stop().
E.g. `ip -d link show vxlan13` after carrier removal before
this patch:
5: vxlan13: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN mode DEFAULT group default
link/ether 1e:47:da:6d:4d:99 brd ff:ff:ff:ff:ff:ff promiscuity 0
vxlan id 13 group 239.0.0.10 dev 2 port 32768 61000 ageing 300
^^^^^
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
