This enables the Broadcom uart bluetooth driver on uart0 and gives it
ownership of its gpios. In order to use this, you must enable the
following kconfig options:
- CONFIG_BT_HCIUART_BCM
- CONFIG_SERIAL_DEV
This is applicable to rk3288-veyron series boards that use the bcm43540
wifi+bt chips.
As part of this change, also refactor the pinctrl across the various
boards. All the boards using broadcom bluetooth shouldn't touch the
bt_dev_wake pin.
Signed-off-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20191127223909.253873-2-abhishekpandit@chromium.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This is like commit 0ca87bd5ba ("ARM: dts: rockchip: Add pin names
for rk3288-veyron-jerry") and commit ca3516b32c ("ARM: dts:
rockchip: Add pin names for rk3288-veyron-minnie") but for 3 more
veyron boards.
A few notes:
- While there is most certainly duplication between all the veyron
boards, it still feels like it is sane to just have each board have
a full list of its pin names. The format of "gpio-line-names" does
not lend itself to one-off overriding and besides it seems sane to
more fully match schematic names. Also note that the extra
duplication here is only in source code and is unlikely to ever
change (since these boards are shipped). Duplication in the .dtb
files is unavoidable.
- veyron-jaq and veyron-mighty are very closely related and so I have
shared a single list for them both with comments on how they are
different. This is just a typo fix on one of the boards, a possible
missing signal on one of the boards (or perhaps I was never given
the most recent schematics?) and dealing with the fact that one of
the two boards has full sized SD.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
mickey crams a lot of hardware into a tiny package, which requires
more aggressive thermal throttling than for devices with a larger
footprint. Configure the GPU thermal zone to throttle the GPU
progressively at temperatures >= 60°C. Heat dissipated by the
CPUs also affects the GPU temperature, hence we cap the CPU
frequency to 1.4 GHz for temperatures above 65°C. Further throttling
of the CPUs may be performed by the CPU thermal zone.
The configuration matches that of the downstream Chrome OS 3.14
kernel, the 'official' kernel for mickey.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
On rk3288 the CPU and GPU temperatures are correlated. Limit the GPU
frequency on veyron mickey to 400 MHz for CPU temperatures >= 65°C
and to 300 MHz for CPU temperatures >= 85°C.
This matches the configuration of the downstream Chrome OS 3.14 kernel,
the 'official' kernel for mickey.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
When I try to boot rk3288-veyron-mickey I totally fail to make the
eMMC work. Specifically my logs (on Chrome OS 4.19):
mmc_host mmc1: card is non-removable.
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: new high speed MMC card at address 0001
mmcblk1: mmc1:0001 HAG2e 14.7 GiB
mmcblk1boot0: mmc1:0001 HAG2e partition 1 4.00 MiB
mmcblk1boot1: mmc1:0001 HAG2e partition 2 4.00 MiB
mmcblk1rpmb: mmc1:0001 HAG2e partition 3 4.00 MiB, chardev (243:0)
mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, actual 50000000HZ div = 0)
mmc1: switch to bus width 8 failed
mmc1: switch to bus width 4 failed
mmc1: tried to HW reset card, got error -110
mmcblk1: error -110 requesting status
mmcblk1: recovery failed!
print_req_error: I/O error, dev mmcblk1, sector 0
...
When I remove the '/delete-property/mmc-hs200-1_8v' then everything is
hunky dory.
That line comes from the original submission of the mickey dts
upstream, so presumably at the time the HS200 was failing and just
enumerating things as a high speed device was fine. ...or maybe it's
just that some mickey devices work when enumerating at "high speed",
just not mine?
In any case, hs200 seems good now. Let's turn it on.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The rk3288-veyron-mickey device tree overrides the default "i2s" clock
settings to add the clock for "i2s_clk_out".
That clock is only present in the bindings downstream Chrome OS 3.14
tree. Upstream the i2s port bindings doesn't specify that as a
possible clock.
Let's remove it.
NOTE: for other rk3288-veyron devices this clock is consumed by
'maxim,max98090'. Presumably if this clock is needed for mickey it'll
need to be consumed by something similar.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Each CPU can (and does) participate in cooling down the system but the
DT only captures a handful of them, normally CPU0, in the cooling maps.
Things work by chance currently as under normal circumstances its the
first CPU of each cluster which is used by the operating systems to
probe the cooling devices. But as soon as this CPU ordering changes and
any other CPU is used to bring up the cooling device, we will start
seeing failures.
Also the DT is rather incomplete when we list only one CPU in the
cooling maps, as the hardware doesn't have any such limitations.
Update cooling maps to include all devices affected by individual trip
points.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Update all 32bit rockchip devicetree files to use SPDX-License-Identifiers.
All files except rk3288-veyron-analog-audio.dtsi (which is GPL 2.0 only)
claim to be GPL and X11 while the actual license text is MIT. Use the
MIT SPDX tag for them.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use macros to describe gpios will make the dts easier to
read and write.
All the modifications done with sed:
sed -i -e 's/ 0 GPIO_ACTIVE_/ RK_PA0 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 1 GPIO_ACTIVE_/ RK_PA1 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 2 GPIO_ACTIVE_/ RK_PA2 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
.......
.......
sed -i -e 's/ 30 GPIO_ACTIVE_/ RK_PD6 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
sed -i -e 's/ 31 GPIO_ACTIVE_/ RK_PD7 GPIO_ACTIVE_/' arch/arm/boot/dts/rk*
Tested with:
for i in dts-old/*dtb; do scripts/dtc/dtx_diff $i dts-new/$(basename $i); done
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
[also adapted the gpio interrupts]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Also known as the Asus Chromebit.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Tested-by: Caesar Wang <wxt@rock-chips.com>
For the license change:
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
