The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly.
Therefore, add a flag to skip any phy power management in the
core layer, leaving it up to the glue driver to manage.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
With the id and vbus detection done via extcon we need to make
sure we poll the status of OTGSC properly by considering what the
extcon is saying, and not just what the register is saying. Let's
move this hw_wait_reg() function to the only place it's used and
simplify it for polling the OTGSC register. Then we can make
certain we only use the hw_read_otgsc() API to read OTGSC, which
will make sure we properly handle extcon events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b0 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.
Get rid of the union and just keep ktime_t as simple typedef of type s64.
The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
- Properly mark little endian descriptors for udc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYO4X5AAoJEEhZKYFQ1nG78yYH/A8GJ6a3pBwvgF3XUhZusp75
w1yg7TnP4aPXDFdS2dpS0buFrBji/0MxTZm3aKNKIHL2jF6ZRW5TvhapA9xv7ezY
BhJOMXMUQAQSG/hnnu8QBJcrd0de3+EUhK6jYKInhvtNQUWl1jW073VAudlp2u4L
lVeHg49+u/10KlZ1Y6yipOH/KzfrOM1oGYBwyl7KMA48R2EASJ0FATcwUM/tRUX3
n6suCg/Z0VVFRdeYkiJdgnjxIbI+QR6TPMV+MWT1O32EniWm3pQT4G3WODooVqO9
oLc+4xgMoPkoiN5XwkYRNZ3wqhDp7xk2v10XJ7zTP1Xrqt2YFBk8K+Ls2/eQmGU=
=uOYb
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
- Adding ULPI PHY support for imx53
- Properly mark little endian descriptors for udc
The internal 60Mhz clock for host2 and host3 are useless in ULPI
phy mode, so we disable it when configuring ULPI PHY node for
those host.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In order to use ULPI phy with usb host 2 and 3, we need to configure
controller register to enable ULPI features.
Each USB controller have different behaviour, so in order to avoid to have
several "swicth(data->index)" and lock/unlock, we prefer to get the index
switch and then test for features if they exist for this index.
This patch also remove useless test of reg and val. Those two values cannot
be NULL.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.co.uk>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The DMA descriptors are little endian, and we do a pretty good
job of handling them with the proper le32_to_cpu() markings, but
we don't actually mark them as __le32. This means checkers like
sparse can't easily find new bugs. Let's mark the members of
structures properly and fix the few places where we're missing
conversions.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Now that usb_endpoint_maxp() only returns the lowest
11 bits from wMaxPacketSize, we can remove the &
operation from this driver.
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We have introduced a helper to calculate multiplier
value from wMaxPacketSize. Start using it.
Acked-by: Peter Chen <Peter.Chen@nxp.com>
Cc: <linux-usb@vger.kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After commit b09b5224fe ("usb: chipidea: implement platform shutdown
callback") and commit 43a404577a ("usb: chipidea: host: set host to
be null after hcd is freed") a NULL pointer dereference is caused
on i.MX23 during shutdown. So ensure that role is set to CI_ROLE_END and
we finish interrupt handling before the hcd is deallocated. This avoids
the NULL pointer dereference.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: b09b5224fe ("usb: chipidea: implement platform shutdown callback")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
According to Documentation/CodingStyle:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
"
, so do as suggested to improve readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
No need to split the dma_pool_zalloc() line into two as it can
perfectly fit into a single line.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
We can make the code simpler by using dma_pool_zalloc() instead
of calling dma_pool_alloc() and then a memset().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The Chipidea EHCI core seems to behave sanely and doesn't need
the IO watchdog. This kills off 10 non-deferrable wakeup events
per second when the controller is otherwise idle.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
This driver make assumptions about the value of the direction flags.
So better use them in comparisons to improve the readability.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
imx usb over current polarity is low active by default, with
over-current-active-high property added, user can config it to be high
active. Meanwhile keep this setting unchanged for existing platforms
so new platform must set the right value for active low by its usbmisc
init function if over current is enabled.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The endpoint fifo is already flushed in _ep_nuke so there
is no need to flush it twice.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Since there should be a write barrier before every call of
hw_ep_prime we could move it into hw_ep_prime.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Problems with the signal integrity of the high speed USB data lines or
noise on reference ground lines can cause the i.MX6 USB controller to
violate USB specs and exhibit unexpected behavior.
It was observed that USBi_UI interrupts were triggered first and when
isr_setup_status_phase was called, ci->status was NULL, which lead to a
NULL pointer dereference kernel panic.
This patch fixes the kernel panic, emits a warning once and returns
-EPIPE to halt the device and let the host get stalled.
It also adds a comment to point people, who are experiencing this issue,
to their USB hardware design.
Cc: <stable@vger.kernel.org> #4.1+
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
When the controller is configured to be dual role and it's in host mode,
if bind udc and gadgt driver, those gadget operations will do gadget
disconnect and finally pull down DP line, which will break host function.
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Chipidea driver has been updated a lot, and more functions are supported,
update Kconfig help text accordingly.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
For each platform devices which is created by device tree, the default
DMA mask is set by of_dma_configure when the device are created. So
delete the redundant code at driver.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots of
other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlbp8/EACgkQMUfUDdst+ylsyQCgnVK6ZIFVPV9VijJvBIjxS3F+
fTMAoIMQwNrRMHQOq/lhxX00AgN0B9Ch
=2EQp
-----END PGP SIGNATURE-----
Merge tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB patchset for 4.6-rc1.
The normal mess is here, gadget and xhci fixes and updates, and lots
of other driver updates and cleanups as well. Full details are in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-4.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (266 commits)
USB: core: let USB device know device node
usb: devio: Add ioctl to disallow detaching kernel USB drivers.
usb: gadget: f_acm: Fix configfs attr name
usb: udc: lpc32xx: remove USB PLL and USB OTG clock management
usb: udc: lpc32xx: remove direct access to clock controller registers
usb: udc: lpc32xx: switch to clock prepare/unprepare model
usb: renesas_usbhs: gadget: fix giveback status code in usbhsg_pipe_disable()
usb: gadget: renesas_usb3: Use ARCH_RENESAS
usb: dwc2: Fix issues in dwc2_complete_non_isoc_xfer_ddma()
usb: dwc2: Add support for Lantiq ARX and XRX SoCs
usb: phy: generic: Handle late registration of gadget
usb: gadget: bdc_udc: fix race condition in bdc_udc_exit()
usb: musb: core: added missing const qualifier to musb_hdrc_platform_data::config
usb: dwc2: Move host-specific core functions into hcd.c
usb: dwc2: Move register save and restore functions
usb: dwc2: Use kmem_cache_free()
usb: dwc2: host: If using uframe scheduler, end splits better
usb: dwc2: host: Totally redo the microframe scheduler
usb: dwc2: host: Properly set even/odd frame
usb: dwc2: host: Add dwc2_hcd_get_future_frame_number() call
...
B-device detects that bus is idle for more than TB_AIDL_BDIS min and
begins HNP by turning off pullup on DP, this allows the bus to discharge
to the SE0 state. This timer was missed and failed with PET test:
6.8.5 B-UUT HNP of USB OTG and EH automated compliance plan v1.2,
this patch is to fix this timing issue.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Enable HNP polling support for chipidea gadget and allocate memory
for host request flag when otg fsm init.
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Set host_request_flag if the current peripheral wants to take host role
via changing a_bus_req or b_bus_req by user application.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Since gadget driver will handle this request, so controller driver bypass
it.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Avoid printing an error if adding the device failes with return
value EPROBE_DEFFER. This may happen e.g. due to missing GPIO for
the vbus-supply regulator.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
In chipidea IP RTL, there is a very limited design for siTD, the detail
like below:
There is no Max Packet Size at siTD, so it uses one constant for both
Max Packet Size for packet and the packet size for the last transaction
when considering schedule.
If the ttctrl.ttha does not match against Hub Address field in siTD,
this constant is 188 bytes, else this constant is 1023 bytes.
If the ttctrl.ttha is non-zero value, RTL will use 188 as this constant,
so it will lose the data if the packet size is larger than 188 bytes, eg,
if we playback a wav which format is 48khz, 16 bits, 2 channels, the
packet size will be 192bytes, but the controller will only send 188 bytes
for this packet, the noise will be heared using USB audio card.
The use case is single transaction, but higher frame rate.
If the ttctr.ttha is zero value, we can send 1023 bytes within one
transaction, but the controller will not accept the coming tranaction
if it considers the schedule time is less than 1023 bytes. So the
limitation is we can't schedule as many as transactions within frame.
If the total bytes is already 256 bytes for previous transactions within
frame, it can't accept another transaction. The use case is multiple
transactions, but less frame rate.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
retval is assigned to be -EOVERFLOW but is overwritten later before
it's used, remove this unused value assignment.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Until now the imx23 uses the imx27 platform flag. But the
imx23 needs the flag CI_HDRC_TURN_VBUS_EARLY_ON, too. So
fix this by adding a separate platform flag.
Suggested-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The write value is 8bit, but currently writing a larger number (eg a doubled
digit) is not errored but instead gets cast and sets off an action probably
undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function usb_phy_generic_register()
returns ERR_PTR() and never returns NULL. The NULL test in
the return value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
The write value is 8bit, but currently writing a larger number
(eg a doubled digit) is not errored but instead gets cast and
sets off an action probably undesired.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
(Change the style of commit log to fix checkpatch.pl warning)
Use list_for_each_entry() instead of list_for_each() to simplify
the code.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull kbuild updates from Michal Marek:
- Make <modname>-m in makefiles work like <modname>-y and fix the
fallout
- Minor genksyms fix
- Fix race with make -j install modules_install
- Move -Wsign-compare from make W=1 to W=2
- Other minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Demote 'sign-compare' warning to W=2
Makefile: revert "Makefile: Document ability to make file.lst and file.S" partially
kbuild: Do not run modules_install and install in paralel
genksyms: Handle string literals with spaces in reference files
fixdep: constify strrcmp arguments
ath10k: Fix build with CONFIG_THERMAL=m
Revert "drm: Hack around CONFIG_AGP=m build failures"
kbuild: Allow to specify composite modules with modname-m
staging/ad7606: Actually build the interface modules
Directly manipulate the controller regsiter to suspend the usb bus
for HNP is not the proper way, this should be done through the usbcore
by usb autosuspend. So to start HNP, autosuspend support should be
added for OTG devices interface driver if it's not enabled.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Set ci->hcd and ci->otg.host to be null in host_stop since the
hcd already freed.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
call to of_find_property() before of_property_read_u32() is unnecessary.
of_property_read_u32() anyway calls to of_find_property() only.
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
disable wakeup irq during shutdown, otherwise kexec fails for
kernels that setup irq handlers before resetting the hardware
Signed-off-by: Andreas Fenkart <andreas.fenkart@dev.digitalstrom.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Since this configuration option has deleted, cleans up all
its references.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Since we need to mount debugfs to show/store the things we
want to debug, it is duplicated to add another configuration
to enable it. Meanwhile, with CONFIG_USB_CHIPIDEA_DEBUG,
we can't support chipidea debugfs at runtime.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Cc: Jun Li <jun.li@freescale.com>
_hardware_enqueue() didn't check for errors when using
add_td_to_list() which can fail if dma_pool_alloc fails, thus
causing a kernel panic when lastnode->ptr is NULL.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Update comments to reflect current state of functions.
Signed-off-by: Felipe F. Tonello <eu@felipetonello.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
This patch sets the AHBMODE to allow for posted data writes. This
results in higher performance.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
replace dma_pool_alloc and memset with a single call to dma_pool_zalloc
Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows to write
drm-$(CONFIG_AGP) += drm_agpsupport.o
without having to handle CONFIG_AGP=y vs. CONFIG_AGP=m. Only support
this syntax for modules, since built-in code depending on something
modular cannot work and init/Makefile actually relies on the current
semantics. There are a few drivers which adapted to the current
semantics out of necessity; these are fixed to also work when the
respective subsystem is modular.
Acked-by: Peter Chen <peter.chen@freescale.com> [chipidea]
Signed-off-by: Michal Marek <mmarek@suse.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Reported-by: coverity (CID 1324138)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
of_match_device could return NULL, and so cause a NULL pointer
dereference later. Renaming tmp_dev to of_id (like all others do) in the
process.
Reported-by: coverity (CID 1324135)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
This patch is to support load and unload gadget driver in full OTG mode.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Jiada Wang <jiada_wang@mentor.com>
Cc: <stable@vger.kernel.org> #v4.0+
Since the ci->role will be set after the host role start is complete, there
will be nobody cared irq during start host if usb irq enabled. This error
can be reproduced on i.mx6 sololite EVK board by:
1. disable otg id irq(IDIE) and disable all real otg properties of usbotg1
in dts.
2. boot up the board with ID cable and usb device connected.
3. echo gadget > /sys/kernel/debug/ci_hdrc.0/role
4. echo host > /sys/kernel/debug/ci_hdrc.0/role
5. irq 212: nobody cared.
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Some i.mx platforms need three clocks to let controller work, but
others only need one, refine clock operation to adapt for all
platforms, it fixes a regression found at i.mx27.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: <stable@vger.kernel.org> #v4.1+
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWKEKdAAoJEEhZKYFQ1nG7dysH/jmFSatDJvgA7woliRZ7p0H/
elNu6AOjqBnsi23Vp54IOVWYTVIDhLsXxlzEOgO6XXfsI99TqFQIIS2VYSo6xues
Eq5hIxh5n9uue3VMnw9bxYHcFkFG9LDAlyMXecEayAB74UqnQLbo2bRDfnSopaf1
dEOq9mdT8llYbtVww6bVXtL78wgwxVk1gTfISllxgt7DEuYwgT+gQJCDLrmkGPn0
XfiaZWamNmDlQd4z/qqoG65+yNmZZMZQKtugCx4MoiBbHVclRN7j2eNsCZ0y6dsZ
qxs+CazL/IeYCqxRRXl5Fopraer1uJeOPeFgA+lRV6WPhMEe7eg6ojkDp/8Y18Y=
=Dh+g
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB Chipidea updates for v4.4-rc1
- Use extcon framework for VBUS and ID detect
- Add imx6sx and imx7d support
- Other small changes
Some HW design may use ID pin state to control vbus for otg port,
so before host role start, the vbus is already turned on, in this
case, we do not need wait vbus dropping below BSV.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Fix using the PCI_DEVICE() macro instead of less verbose PCI_VDEVICE().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add imx6ul usb support.
Signed-off-by: Peter chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add support for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power mode
and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use imx6sx instead of imx6sl's platform flags for imx6sx.
Fixes: e14db48dfc ("usb: chipidea: imx: add runtime power management support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Due to having hardware tx buffers less than 512 bytes in size, streaming
must be enabled on the Zynq for the udc to work at all. Add platform data
specific to the Zynq udc, which does not set the CI_HDRC_DISABLE_STREAMING
flag.
Based on a patch by the same name from the Xilinx vendor tree.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
According to spec, there are functional and protocol stalls.
For functional stall, it is for bulk and interrupt endpoints,
below are cases for it:
- Host sends SET_FEATURE request for Set-Halt, the udc driver
needs to set stall, and return true unconditionally.
- The gadget driver may call usb_ep_set_halt to stall certain
endpoints, if there is a transfer in pending, the udc driver
should not set stall, and return -EAGAIN accordingly.
These two kinds of stall need to be cleared by host using CLEAR_FEATURE
request (Clear-Halt).
For protocol stall, it is for control endpoint, this stall will
be set if the control request has failed. This stall will be
cleared by next setup request (hardware will do it).
It fixed usbtest (drivers/usb/misc/usbtest.c) Test 13 "set/clear halt"
test failure, meanwhile, this change has been verified by
USB2 CV Compliance Test and MSC Tests.
Cc: <stable@vger.kernel.org> #3.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.
Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVzU3lAAoJEEhZKYFQ1nG7nZ4H/AsCAhoiUqcyP4fRziaZzexa
F55CuhIVd6vg6vhuiccoUo4XZXR6IsZikczNowWphqXhtQUBr/rvv0VSb2sMxZfn
AgdNuinhGUat4rdcf0earr9+EQzjbdrHoxDzFKes21S0vS+J3TaYUk6F7Q6sUL81
t97itMmKBrffMZLsQzB9MJo4E8mD4JNlWu/ezGNu11ZD2/w8Ha7GpyExyb2AGHrs
M1rlE6Ph8AKpyECI7OecCxPIDyDRuUQ8Bvj+MkR9BrDX1gOv512ZLfRbIGJCqVOO
A2Urzh/jEI9e7ttGqSpMxGYKZ4wvZ7Ta5IvLLseb0vszM2oQGDNHcJx7fKOuUVU=
=IIud
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
USB: chipidea updates for v4.3-rc1
The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.
Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WuIB
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.3 merge window
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
With this setting and AHBBRST at SBUSCFG as "Incremental burst of
unspecified length", each non-burst size can be taken as single
transfer. It is benefit for non-burst size transfer.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Stream mode enable is known for better performance, this stream mode
enable patch has been passed with stress tests at device mode for
imx6sl and imx6sx, and no issue is found.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The system bus and chipidea IP have different limitations for
both host and device mode.
For example, with below errata, we need to enable SDIS(Stream Disable
Mode) at host mode. But we don't want it for device mode at the
same system.
TAR 9000378958
Title: Non-Double Word Aligned Buffer Address Sometimes Causes Host to
Hang on OUT Retry
Impacted Configuration: Host mode, all transfer types
Description:
The host core operating in streaming mode may under run while sending
the data packet of an OUT transaction. This under run can occur if
there are unexpected system delays in fetching the remaining packet
data from memory. The host forces a bad CRC on the packet, the device
detects the error and discards the packet. The host then retries a Bulk,
Interrupt, or Control transfer if an under run occurs according to the
USB specification. During simulations, it was found that the host does
not issue the retry of the failed bulk OUT. It does not issue any other
transactions except SOF packets that have incorrect frame numbers.
The second failure mode occurs if the under run occurs on an ISO OUT
transaction and the next ISO transaction is a zero byte packet. The host
does not issue any transactions (including SOFs). The device detects a
Suspend condition, reverts to full speed, and waits for resume signaling.
A third failure mode occurs when the host under runs on an ISO OUT and
the next ISO in the schedule is an ISO OUT with two max packets of 1024
bytes each. The host should issue MDATA for the first OUT followed by
DATA1 for the second. However, it drops the MDATA transaction, and
issues the DATA1 transaction.
The system impact of this bug is the same regardless of the failure mode
observed. The host core hangs, the ehci_ctrl state machine waits for the
protocol engine to send the completion status for the corrupted
transaction, which never occurs. No indication is sent to the host
controller driver, no register bits change and no interrupts occur.
Eventually the requesting application times out.
Detailed internal behavior:
The EHCI control state machine (ehci_ctrl) in the DMA block is responsible
for parsing the schedules and initiating all transactions. The ehci_ctrl
state machine passes the transaction details to the protocol block by
writing the transaction information in to the TxFIFO. It then asserts
the pe_hst_run_pkt signal to inform the host protocol state machine
(pe_hst_state) that there is a packet in the TxFIFO.
A tag of 0x0 indicates a start of packet with the data providing the
following information:
35:32 Tag
31:30 Reserved
29:23 Endpoint (lowest 4 bits)
22:16 Address
15:10 Reserved
9:8 Endpoint speed
7:6 Endpoint type
5:6 Data Toggle
3:0 PID
The pe_hst_state reads the packet information and constructs the packet
and issues it to the PHY interface.
The ehci_ctrl state machine writes the start transaction information in
to the TxFIFO as 0x03002910c for the OUT packet that had the under run
error. However, it writes 0xC3002910C for the retry of the Out
transaction, which is incorrect.
The pe_hst_state enters a bus timeout state after sending the bad CRC
for the packet that under ran. It then purges any data that was back
filled in to the TxFIFO for the packet that under ran. The pe_hst_state
machine stops purging the TxFIFO when it is empty or if it reads a
location that has a tag of 0x0, indicating a start of packet command.
The pe_hst_state reads 0xC3002910C and discards it as it does not decode
to a start of packet command. It continues to purge the OUT data that
has been pre-buffered for the OUT retry . The pe_hst_state detects the
hst_packet_run signal and attempts to read the PID and address
information from the TxFIFO. This location has packet data and so does
not decode to a valid PID and so falls through to the PE_HST_SOF_LOAD
state where the frame_num_counter is updated. The frame_num_counter
is updated with the data in the TxFIFO. In this case, the data is
incorrect as the ehci_ctrl state machine did not initiate the load.
The hst_pe_state machine detects the SOF request signal and sends an
SOF with the bad frame number. Meanwhile, the ehci_ctrl state machine
waits indefinitely in the run_pkt state waiting for the completion
status from pe_hst_state machine, which will never happen.
The ISO failure case is similar except that there is no retry for ISO.
The ehci_ctrl state machine moves to the next transfer in the periodic
schedule. If the under run occurs on the last entry of the periodic
list then it moves to the Async schedule.
In the case of ISO OUT simulations, the next ISO is a zero byte OUT
and again the start of packet command gets corrupted. The TxFIFO is
empty when the hst_pe_state attempts to read the Address and PID
information as the transaction is a zero byte packet. This results
in the hst_pe_state machine staying in the GET_PID state, which means
that it does not issue any transactions (including SOFs). The device
detects a Suspend condition and reverts to full speed mode and waits
for a Resume or Reset signal.
The EHCI specification allows a Non-DoubleWord (32 bits) offset to
be used as a current offset for Buffer Pointer Page 0 of the qTD.
In Non-DoubleWord aligned cases, the core reads the packet data
from the AHB memory, performs the alignment operation before writing
it in to the TxFIFO as a 32 bit data word. An End Of Packet tag (EOP)
is written to the TxFIFO after all the packet data has been written
in to the TxFIFO. The alignment function is reset to Idle by the EOP
tag. The corruption of the start of packet command arises because the
packet buffer for the OUT transaction that under ran is not aligned
to a DoubleWord, and hence no EOP tag is written to the TxFIFO. The
alignment function is still active when the start packet information
is written in to the TxFIFO for the retry of the bulk packet or for
the next transaction in the case of an under run on an ISO. This
results in the corruption of the start tag and the transaction
information.
Click for waveform showing the command 0x 0000300291 being written in
to the TX FIFO for the Out that under ran.
Click for waveform showing the command 0xC3002910C written to the
TxFIFO instead of 0x 0000300291
Versions affected: Versions 2.10a and previous versions
How discovered: Customer simulation
Workaround:
1- The EHCI specification allows a non-DoubleWord offset to be used
as a current offset for Buffer Pointer Page 0 of the qTD. However,
if a DoubleWord offset is used then this issue does not arise.
2- Use non streaming mode to eliminate under runs.
Resolution:
The fix involves changes to the traffic state machine in the
vusb_hs_dma_traf block. The ehci_ctrl state machine updates the context
information by encoding the transaction results on the
hst_op_context_update signals at the end of a transaction. The signal
hst_op_context_update is added to the traffic state machine, and the
tx_fifo_under_ran_r signal is generated if the transaction results in
an under run error. Click for waveform
The traffic state machine then traverses to the do_eop states if the
tx_fifo_under_ran error is asserted. Thus an EOP tag is written in to
the TxFIFO as shown in this waveform .
The EOP tag resets the align state machine to the Idle state ensuring
that the next command written by the echi_ctrl state machine does not
get corrupted.
File(s) modified:
RTL code fixed: …..
Method of reproducing: This failure cannot be reproduced in the current
test bench.
Date Found: March 2010
Date Fixed: June 2010
Update information:
Added the RTL code fix
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The zero-length packet is the sendor tells the receiver that there
is no more data, so it is only needed at the TX side.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The system configuration API should be called before the controller
run, otherwise, undefined results may occur. So, we override hcd
reset API, and add system configuration API after controller reset.
Cc: Li Jun <peter.chen@freescale.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
If usbmisc hasn't probed yet, defer the probe.
It's not enough to check if the platform device for the OF node of the
usbmisc has been registered, but it also needs to have been probed
already before we can call imx_usbmisc_init().
This can happen if the order in which devices are probed change due to
async probing or on-demand probing of dependencies.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
This makes the function hw_alloc_repmap be declared to have a return
type of void now due to this particular function never returning
a error code to its caller due to this function always running
successfully to completion nor it's caller putting the return
value into a variable in order to check if a error code is passed
from the function hw_alloc_repmap when calling this function.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
The struct ci_hdrc is the drvdata for hcd device, so we don't
need to introduce extra ci_hdrc structure for ehci.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
ITC (Interrupt Threshold Control) is used to set the maximum rate at which
the host/device controller will issue interrupts. The default value is 8 (1ms)
for it. EHCI core will modify it to 1, but device mode keeps it as default
value.
In some use cases like Android ADB, it only has one usb request for each
direction, and maximum payload data is only 4KB, so the speed is 4MB/s
at most, it needs controller to trigger interrupt as fast as possible
to increase the speed. The USB performance will be better if the interrupt
can be triggered faster.
Reduce ITC value is benefit for USB performance, but the interrupt number
is increased at the same time, it may increase cpu utilization too.
Most of use case cares about performance, but some may care about
cpu utilization, so, we leave a platform interface for user.
We set ITC as 1 (1 micro-frame) as default value which is aligned
with ehci core default value.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
It is used to configure controller parameters according to
platform data, like speed, stream mode, etc, both host and
device's initialization need it, most of code are the
same for both roles, with this new interface, it can reduce
the duplicated code and be easy to maintain in future.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
We can support USB OTG 1.3 USB_DEVICE_A_HNP_SUPPORT request when
the driver supports OTG FSM mode.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
For i.mx platform, set ttctrl.ttha with non-zero value only affects
sitd, and ehci core makes sure the schedule is not full when accepts
new request, so it will not occur the transaction which will acorss
the SoF.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
The register of ttctrl.ttha describes like below:
- Internal TT Hub Address Representation
- RW
- Default = 0000000b
This field is used to match against the Hub Address field in QH & siTD
to determine if the packet is routed to the internal TT for directly
attached FS/LS devices. If the Hub Address in the QH or siTD does not
match this address then the packet will be broadcast on the High Speed
ports destined for a downstream High Speed hub with the address in the QH/siTD.
In silicon RTL, this entry only affects QH and siTD, and the hub.addr at
both QH and siTD are 0 in ehci core for chipidea (with hcd->has_tt = 1).
So, for QH, if the "usage_tt" flag at RTL is 0, set CI_HDRC_SET_NON_ZERO_TTHA
will not affect QH (with non-hs device); for siTD, set this flag
will change remaining space requirement for the last transaction from 1023
bytes to 188 bytes, it can increase the number of transactions within one
frame, ehci periodic schedule code will not queue the packet if the frame space
is full, so it is safe to set this flag for siTD.
With this flag, it can fix the problem Alan Stern reported below:
http://www.spinics.net/lists/linux-usb/msg123125.html
And may fix Michael Tessier's problem too.
http://www.spinics.net/lists/linux-usb/msg118679.html
CC: stern@rowland.harvard.edu
CC: michael.tessier@axiontech.ca
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since some chipidea based controller is not otg capable, add ci->is_otg
condition when setting is_otg flag for gadget.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After introduce usb otg properties, update ci_otg_is_fsm_mode conditions
to be depending on both usb hardware properties and usb driver config,
also resolve a compile issue in debug.c after the API change.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Init and update otg capabilities by DT, set gadget's otg capabilities
accordingly.
Acked-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just a minor change for code style
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVdQexAAoJEEhZKYFQ1nG7/M0H/3gZcnjvF2nN6NYBUhFpz33r
BAIDYumRhAPOVbnmXYZOh24+yPEhKYTWaZycjQeJXBVd23r8EFGP4Vl+K6vCTtJX
jIQZ+73ntPwDBgvDfPN1Lk+Kj2G3dPl6b+ZmmAj1lS1ea2ewDR5Q+OM3/bX6kscN
zccMIMv/++jLOvAeOvoa5Hk7JZdQK+DQaSCLRZAfEfID40I0A7j6OcWP3B8qebGD
faYc9XfA+Li/C1q7qvUFWTWHcVkQT56syffLXetts3sOuo7EzPlyyBT6zreKi//a
MHWv+VBkoQvqDYej7fLqfpRBy221beEfFXH5DAcDRr7q1ikKUIPWxiqwUOnJ4P0=
=Yq7y
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-work
Peter writes:
USB Chipidea update for v4.2-rc1
Just a minor change for code style
The Marvell 28nm HSIC PHY requires the port to be forced to HS mode after
the port power is applied. This is done using the test mode in the PORTSC
register.
As HSIC is always HS, this work-around should be safe to do with all HSIC
PHYs and has been tested on i.MX6S.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, ci_default_pdata is common to all instances of the driver and
gets modified by the core driver code. This is bad if there are multiple
instances of the device with different settings such as the phy type. Fix
this by making a copy of the default platform_data.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unneeded semicolon.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/semicolon.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
A string written by the user may not be zero terminated.
sscanf may read memory beyond the buffer if no zero byte
is found.
For testing build with CONFIG_USB_CHIPIDEA=y, CONFIG_USB_CHIPIDEA_DEBUG=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Wrongly release mutex lock during otg_statemachine may result in re-enter
otg_statemachine, which is not allowed, we should do next state transtition
after previous one completed.
Fixes: 826cfe751f ("usb: chipidea: add OTG fsm operation functions implementation")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the required clock to access registers is gated off in low power mode,
add ci->in_lpm check before try to dump registers value.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
By pass pullup DP in OTG fsm mode when do gadget connect, to let it handled
by OTG state machine.
This patch can fix the problem you found with my HNP polling patchset after
below 3 patches introduced:
467a78c usb: chipidea: udc: apply new usb_udc_vbus_handler interface
628ef0d usb: udc: add usb_udc_vbus_handler
dfea9c9 usb: udc: store usb_udc pointer in struct usb_gadget
Problem:
- Connect USB cable and MicroAB cable between two boards
- Boot up two boards
- load g_mass_storage at B-device side, the enumeration will success,
and A will see a usb mass-storage device
- load g_mass_storage at A-device side, the problem has occurred, the
connection will be lost at the beginning, then connect again.
This patch is based on
commit eff933c1d3a2e046492b3dfc86db813856553a29
(chipidea: pci: make it depends on NOP_USB_XCEIV)
on branch peter-usb-dev of
git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb.git
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
After commit ba1aff67f9 (chipidea: pci: register nop PHY) the PCI glue driver
requires nop-PHY to be selected. Thus, make it an explicit dependency.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: ba1aff67f9 (chipidea: pci: register nop PHY)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces USB_CHIPIDEA_PCI and USB_CHIPIDEA_OF Kconfig options, one
per each specific glue driver. This is needed to provide different dependencies
they have.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current otg fsm timers are using controller 1ms irq and count it, this patch
is to replace it with hrtimer solution, use one hrtimer for all otg timers.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
B_DATA_PLS(data-line pulse time) and B_SSEND_SRP(session end to SRP init) are
also from OTG&EH 2.0 Specification and they are not chipidea specific.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since BSV irq is enabled for B-device all the time, so B_SESS_VLD timer
is not required, and also no need to check BSV status when B_ASE0_BRST
timer timeout.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=U+M2
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
It can move all pullup/pulldown operation control to udc-core
through usb_gadget_connect/usb_gadget_disconnect according to
vbus status.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch adds runtime power management support for otg fsm mode, since
A-device in a_idle state cannot detect data pulse irq after suspended, here
enable wakeup by connection before suspend to make it can be resumed by DP;
and handle wakeup from that state like SRP.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If CI_HDRC_TURN_VBUS_EARLY_ON is set, turn on vbus before adding hcd, so it
will not set reg_vbus of ehci_ci_priv, then vbus will not be handled by ehci core.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some usb PHYs need power supply from vbus to make it work, eg mxs-phy, if
there is no vbus, USB PHY will not in correct state when the controller starts
to work, for host, this requires vbus should be turned on before setting port
power(PP) of ehci, to work with this kind of USB PHY design, this patch adds
a flag CI_HDRC_TURN_VBUS_EARLY_ON, can be checked by host driver to turn on
vbus while start host.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since PHY for ChipIdea is optional (not all SoCs having PHY for ChipIdea should
be programmed), we register 'nop' PHY for platforms that do not have
programmable PHY.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For chipidea, its resume sequence is not-EHCI compatible, see
below description for FPR at portsc. So in order to send SoF in
time for remote wakeup sequence(within 3ms), the RUN/STOP bit must
be set before the resume signal is ended, but the usb resume
code may run after resume signal is ended, so we had to set it
at suspend path.
Force Port Resume - RW. Default = 0b.
1= Resume detected/driven on port.
0=No resume (K-state) detected/driven on port.
Host mode:
Software sets this bit to one to drive resume signaling. The Controller sets this bit to '1' if
a J-to-K transition is detected while the port is in the Suspend state. When this bit
transitions to a '1' because a J-to-K transition is detected, the Port Change Detect bit in
the USBSTS register is also set to '1'. This bit will automatically change to '0' after the
resume sequence is complete. This behavior is different from EHCI where the controller
driver is required to set this bit to a '0' after the resume duration is timed in the driver.
Note that when the controller owns the port, the resume sequence follows the defined
sequence documented in the USB Specification Revision 2.0. The resume signaling
(Full-speed 'K') is driven on the port as long as this bit remains a '1'. This bit will remain
a '1' until the port has switched to idle. Writing a '0' has no affect because the port
controller will time the resume operation, clear the bit and the port control state switches
to HS or FS idle.
This field is '0' if Port Power(PP) is '0' in host mode.
This bit is not-EHCI compatible.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PORTSC_PFSC is not set on entering host mode which means the USB OTG
controller will attempt to enumerate USB devices at high speed even when the
CI_HDRC_FORCE_FULLSPEED flag is set in the platform data.
This patch ensures it is set right before host mode operations begin if needed.
Signed-off-by: Daniel Tang <dt.tangr@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At chipidea revision 2.40a, there is a below errata:
9000531823 B2-Medium Adding a dTD to a Primed Endpoint May Not Get Recognized
Title: Adding a dTD to a Primed Endpoint May Not Get Recognized
Impacted Configuration: All device mode configurations.
Description:
There is an issue with the add dTD tripwire semaphore (ATDTW bit in USBCMD register)
that can cause the controller to ignore a dTD that is added to a primed endpoint.
When this happens, the software can read the tripwire bit and the status bit at '1'
even though the endpoint is unprimed.
After executing a dTD, the device controller endpoint state machine executes a final
read of the dTD terminate bit to check if the application added a dTD to the linked
list at the last moment. This read is done in the finpkt_read_latest_next_td (44) state.
After the read is performed, if the terminate bit is still set, the state machine moves
to unprime the endpoint. The decision to unprime the endpoint is done in the
checkqh_decision (59) state, based on the value of the terminate bit.
Before reaching the checkqh_decision state, the state machine traverses the
writeqhtd_status (57), writeqh_status (56), and release_prime_mask (42) states.
As shown in the waveform, the ep_addtd_tripwire_clr signal is not set to clear
the tripwire bit in these states.
Workaround:
The software must implement a periodic poll cycle, and check for each dTD
pending on execution (Active = 1), if the enpoint is primed. It can do this by reading
the corresponding bits in the ENDPTPRIME and ENDPTSTAT registers. If these bits are
read at 0, the software needs to re-prime the endpoint by writing 1 to the corresponding
bit in the ENDPTPRIME register. This can be done for every microframe, every frame or
with a larger interval, depending on the urgency of transfer execution for the application.
Tested-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define ci_get_revision API to know the controller revision
information according to chipidea 1.1a, 2.0a and 2.5a spec.
Besides, add one entry at struct ci_hdrc to indicate revision
information, it can be used for adding different code for
revisions, eg kinds of errata.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using hw_write_id_reg and hw_read_id_reg to write and read identification
registers contents, they can be used to get controller information, change
some system configurations, and so on.
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Except the same process with earlier imx6, it has below two features:
- Choose which vbus voltage as vbus wakeup source
We choose B_SESSION_VALID as vbus wakeup source since when the system
goes to suspend, the vbus comparator can't compare the vbus voltage
for VBUS_VALID.
- Disable dp/dm (linestate) change as wakeup source at device mode
when the vbus is not there, we don't expect dp/dm change waking up
usb controller at this situation.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to do it for all otg capable controller, not only peripheral
featured otg capable controller, otherwise, the host-only role, but
otg capable controller may be responded by otg interrupt.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable USB as system wakeup source, and each platform needs to implement
imx_usbmisc_set_wakeup in usbmisc_imx.c to support.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The USB signal can be system wakeup source, this patch add the
support, for how to enable it, see Documentation/usb/chipidea.txt.
Since USB wakeup enable logic is vendor/platform specific, the
glue layer needs to implement it to support this feature.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add runtime pm support for imx, only imx6 series are supported and tested.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This API is used to enable/disable usb wakeup, only imx6 series are
added, since I don't have other imx hardware on hand. Other imx users
can add their API according to reference manual after testing.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move struct imx_usbmisc_data NULL pointer judgement from caller to
each API, it can simplify the caller.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All imx usb controller's non core registers uses the same clock gate with
core registers, the usbmisc_imx is the library for imx glue driver, the
glue keeps clock on when it calls usbmisc_imx API to change non-core register.
Besides, we will support runtime pm in the future, it also needs to
close this clock when the usb is not in use.
Philipp Zabel also verifies it at imx6q platform, see
http://www.spinics.net/lists/linux-usb/msg118491.html
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is meaningless the glue layer driver has its own platform flag
which is the same meaning with common platform flag.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some gadget driver (like uac1) will try to enable endpoint again even
the ep is not empty, it will cause the ep reset again and may affect
the dTD list which has already queued.
It returns -EBUSY immediately, and indicate the endpoint is in use.
In this way, the ep's behavior will not be affected, and the gadget
driver is also notified.
Cc: Xuebing Wang <xbing6@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds response to a_alt_hnp_support set feature request from legacy
A device, that is, B-device can provide a message to the user indicating that
the user needs to connect the B-device to an alternate port on the A-device.
A device sets this feature indicates to the B-device that it is connected
to an A-device port that is not capable of HNP, but that the A-device does have
an alternate port that is capable of HNP.
[Peter]
Without this patch, the OTG B device can't be enumerated on
non-HNP port at A device, see below log:
[ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.293105] usb 1-1: can't set HNP mode: -32
[ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc
[ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.466424] usb 1-1: can't set HNP mode: -32
[ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc
[ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port
[ 2.636436] usb 1-1: can't set HNP mode: -32
[ 2.641003] usb usb1-port1: unable to enumerate USB device
Cc: stable <stable@vger.kernel.org>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=bGMq
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.20 merge window
Here's the big pull request for Gadgets and PHYs. It's
a total of 217 non-merge commits with pretty much everything
being touched.
The most important bits are a ton of new documentation for
almost all usb gadget functions, a new isp1760 UDC driver,
several improvements to the old net2280 UDC driver, and
some minor tracepoint improvements to dwc3.
Other than that, a big list of minor cleanups, smaller bugfixes
and new features all over the place.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is a follow up to the previously submitted commit cefa9a31a5 (ehci-pci:
disable for Intel MID platforms).
It includes the following changes:
- table and function are renamed to reflect this is not only about ChipIdea
- ChipIdea PCI driver (ci_hdrc_pci.c) gets the comment about the table in
ehci-pci.c
- MIPS IDs removed from the list since it was discovered and tested on Intel
MID platforms
Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget power property will be used at get_status request.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 14b4099c07
It moved platform_set_drvdata(pdev, ci) before hcd is created,
and the hcd will assign itself as ci controller's drvdata during
the hcd creation function (in usb_create_shared_hcd), so it
overwrites the real ci's drvdata which we want to use.
So, if the controller is at host mode, the system suspend
API will get the wrong struct ci_hdrc pointer, and cause the
oops.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
drivers/usb/chipidea/ci_hdrc_usb2.c:108:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Cc: Antoine Tenart <antoine.tenart@free-electrons.com>
Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed typos in comments of 2 drivers/usb/chipidea files
Signed-off-by: Mickael Maison <mickael.maison@gmail.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a USB2 ChipIdea driver for ci13xxx, with optional PHY, clock
and DMA mask, to support USB2 ChipIdea controllers that don't need
specific functions.
Tested on the Marvell Berlin SoCs USB controllers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic plaftorm device for ChipIdea drivers is probed by calling
ci_hdrc_probe. The device structure used is not the one of the specific
ChipIdea driver but the one of the generic ChipIdea platform device.
This results in not being able to probe the PHYs as we're not using the
right device structure. Since all ChipIdea drivers are retrieving their
PHYs in their specific driver code, this didn't impact any of them yet.
Fixes it using the right device structure (dev->parent).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core driver has already done it, besides, move set driver data
operation just after ci has allocated successfully in case some
code (like ci_role_start) want to access this driver data.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The hw_device_reset is dedicated to be used at device mode initializaiton,
so delete the parameter 'mode'. For host driver, the ehci driver will
handle all things.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add controller reset API, currently it is used for device mode only.
It may be used for host/otg driver in future.
Ususally, we need this API for dual-role switch and back from hibernation
suspend to let the controller at default state.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, USB PHY is mandatory for chipidea core, the flag
CI_HDRC_REQUIRE_TRANSCEIVER is useless.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add basic system power management support
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
