-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJaW+iVAAoJEHm+PkMAQRiGCDsIAJALNpX7odTx/8y+yCSWbpBH
E57iwr4rmnI6tXJY6gqBUWTYnjAcf4b8IsHGCO6q3WIE3l/kt+m3eA21a32mF2Db
/bfPGTOWu5LoOnFqzgH2kiFuC3Y474toxpld2YtkQWYxi5W7SUtIHi/jGgkUprth
g15yPfwYgotJd/gpmPfBDMPlYDYvLlnPYbTG6ZWdMbg39m2RF2m0BdQ6aBFLHvbJ
IN0tjCM6hrLFBP0+6Zn60pevUW9/AFYotZn2ankNTk5QVCQm14rgQIP+Pfoa5WpE
I25r0DbkG2jKJCq+tlgIJjxHKD37GEDMc4T8/5Y8CNNeT9Q8si9EWvznjaAPazw=
=o5gx
-----END PGP SIGNATURE-----
BackMerge tag 'v4.15-rc8' into drm-next
Linux 4.15-rc8
Daniel requested this for so the intel CI won't fall over on drm-next
so often.
The omap4 CEC hardware cannot tell a Nack from a Low Drive from an
Arbitration Lost error, so just report a Nack, which is almost
certainly the reason for the error anyway.
This also simplifies the implementation. The only three interrupts
that need to be enabled are:
Transmit Buffer Full/Empty Change event: triggered when the
transmit finished successfully and cleared the buffer.
Receiver FIFO Not Empty event: triggered when a message was received.
Frame Retransmit Count Exceeded event: triggered when a transmit
failed repeatedly, usually due to the message being Nacked. Other
reasons are possible (Low Drive, Arbitration Lost) but there is no
way to know. If this happens the TX buffer needs to be cleared
manually.
While testing various error conditions I noticed that the hardware
can receive messages up to 18 bytes in total, which exceeds the legal
maximum of 16. This could cause a buffer overflow, so we check for
this and constrain the size to 16 bytes.
The old incorrect interrupt handler could cause the CEC framework to
enter into a bad state because it mis-detected the "Start Bit Irregularity
event" as an ARB_LOST transmit error when it actually is a receive error
which should be ignored.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Henrik Austad <haustad@cisco.com>
Tested-by: Henrik Austad <haustad@cisco.com>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Currently, calls into each file are used to register the various
platform drivers. Change this to a table of pointers to platform_driver
structs to allow using platform_register_drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Having the filename in the header serves little purpose and is
often wrong after renames as it is here in several places, just
drop it from all omapdrm files.
While we are here unify the copyright tags to the TI recommended style.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Check the status of the DMM engine after it is reported that the
transaction was completed as in rare cases the engine might not reached a
working state.
The wait_status() will print information in case the DMM is not reached the
expected state and the dmm_txn_commit() will return with an error code to
make sure that we are not continuing with a broken setup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
To help diagnose DMM errors, print out information if any of the error bits
are set in the interrupt status register.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If the wait_status() fails either because of an error reported in the
STATUS register or because of a timeout waiting for the wait_mask, print
information which might help diagnose the reason.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The error bit definitions are typoed in DMM_IRQSTAT_ERR_MASK which went
unnoticed since the DMM_IRQSTAT_ERR_MASK was not used.
Change the bit definitions to the correct ones.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The number of function declarations in the omap_drv.h degrades
readability. To fix it, create new header files for each part of the
driver and move the related functions.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The venc_probe_of() function has an error cleanup path that returns
success instead of an error code. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The dpi_data structure port_initialized field is used to check in the
cleanup path whether the DPI has been initialized. This can be performed
through the associated device_node data field instead. Remove the
port_initialized field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The function isn't used outside of its compilation unit, make it static.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When merging the omapdrm and omapdss drivers the omapdrm virtual
platform device will disappear, and the omapdss platform device will be
used for DMA memory allocation. To prepare for that, set the DMA
coherent mask for the device.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_find_device() function is unused. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_gem_resume() function is internal to the driver. Pass it a
drm_device pointer that the caller already has instead of looking it up
from device data.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
There's no need to print an error message on probe deferral, that's a
normal situation. Probe deferral debugging can be performed by enabling
the related debug messages in the drivers core.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the new descriptor based GPIO API instead of
the legacy one, which results in cleaner code
with less lines of code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Droid 4 has a command mode DSI panel, which does not have/use
DSI based backlight support. This adds proper support for this
using a backlight phandle property, which follows the common
panel binding.
If no backlight phandle is found, it is assumed, that the
native backlight should be used instead. This is used by
the Nokia N950.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support to load physical size information from DT using
the properties defined by the common panel binding.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add support for regulators used by panels found inside
of the Nokia N950, N9 and Motorola Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This adds support for get_timings() and check_timings()
to get the driver working and properly initializes the
timing information from DT.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
While physical size information is automatically parsed for EDID
based displays, we need to provide it manually for displays providing
one fixed mode.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The wrappers have been removed in commit 5a35876e28
(drm: omapdrm: Remove manual update display support)
and will not be reintroduced, since the normal sys
functions properly call the dirty callback.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove driver (un)register API defines. They do not even exist
anymore.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If we have memory bandwidth limit configured, reject the modes which would
require more bandwidth than the limit if it is used with one full
resolution plane (most common use case).
This filtering is not providing full protection as it is possible that
application would pick smaller crtc resolution with high resolution planes
and down scaling, or can enable more smaller planes where the sum of their
bandwidth need would be higher than the limit.
This patch only allows us to filter out modes which would need more
bandwidth if they were used with one full screen plane.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The get_memory_bandwidth_limit() in dispc_ops can be used to query the
memory bandwidth limit of dispc by upper layers.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
to make it easier to keep in sync with the OF device table.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The vendor name was "toppoly" but other panels and the vendor list
have defined it as "tpo". So let's fix it in driver and bindings.
We keep the old definition in parallel to stay compatible with
potential older DTB setup.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This driver can use drm_fb_helper_lastclose() as its .lastclose callback.
It can also use drm_fb_helper_output_poll_changed() as its
.output_poll_changed callback.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171205182504.41923-9-noralf@tronnes.org
"ret" needs to be signed for the error handling to work.
Fixes: 8d7f934df8 ("omapdrm: hdmi4_cec: add OMAP4 HDMI CEC support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Commit d178e034d5 ("drm: omapdrm: Move FEAT_DPI_USES_VDDS_DSI feature
to dpi code") replaced usage of platform data version with SoC matching
to configure DPI VDDS. The SoC match entries were incorrect, they should
have matched on the machine name instead of the SoC family. Fix it.
The result was observed on OpenPandora with OMAP3530 where the panel only
had the Blue channel and Red&Green were missing. It was not observed on
GTA04 with DM3730.
Fixes: d178e034d5 ("drm: omapdrm: Move FEAT_DPI_USES_VDDS_DSI feature to dpi code")
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: stable@vger.kernel.org # 4.14
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
I believe the intention of the commit 2c9fc9bf45
("drm: omapdrm: Move FEAT_HDMI_* features to hdmi4 driver")
was to identify omap4430 ES1.x, omap4430 ES2.x and other OMAP4 revisions,
like omap4460.
By using family=OMAP4 in the match the code will treat omap4460 ES1.x in a
same way as it would treat omap4430 ES1.x
This breaks HDMI audio on OMAP4460 devices (PandaES for example).
Correct the match rule so we are not going to get false positive match.
Fixes: 2c9fc9bf45 ("drm: omapdrm: Move FEAT_HDMI_* features to hdmi4 driver")
Cc: stable@vger.kernel.org # 4.14
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The new backlight code causes a link failure when backlight
support itself is disabled:
drivers/gpu/drm/omapdrm/displays/panel-dpi.o: In function `panel_dpi_probe_of':
panel-dpi.c:(.text+0x35c): undefined reference to `of_find_backlight_by_node'
This adds a Kconfig dependency like we have for the other OMAP
display targets.
Fixes: 39135a305a ("drm/omap: displays: panel-dpi: Support for handling backlight devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If we don't find a matching device node, we must free the memory allocated
in 'omap_dmm' a few lines above.
Fixes: 7cb0d6c17b ("drm/omap: fix TILER on OMAP5")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This mechanically converts all remaining cases of ancient open-coded timer
setup with the old setup_timer() API, which is the first step in timer
conversions. This has no behavioral changes, since it ultimately just
changes the order of assignment to fields of struct timer_list when
finding variations of:
init_timer(&t);
f.function = timer_callback;
t.data = timer_callback_arg;
to be converted into:
setup_timer(&t, timer_callback, timer_callback_arg);
The conversion is done with the following Coccinelle script, which
is an improved version of scripts/cocci/api/setup_timer.cocci, in the
following ways:
- assignments-before-init_timer() cases
- limit the .data case removal to the specific struct timer_list instance
- handling calls by dereference (timer->field vs timer.field)
spatch --very-quiet --all-includes --include-headers \
-I ./arch/x86/include -I ./arch/x86/include/generated \
-I ./include -I ./arch/x86/include/uapi \
-I ./arch/x86/include/generated/uapi -I ./include/uapi \
-I ./include/generated/uapi --include ./include/linux/kconfig.h \
--dir . \
--cocci-file ~/src/data/setup_timer.cocci
@fix_address_of@
expression e;
@@
init_timer(
-&(e)
+&e
, ...)
// Match the common cases first to avoid Coccinelle parsing loops with
// "... when" clauses.
@match_immediate_function_data_after_init_timer@
expression e, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
@match_immediate_function_data_before_init_timer@
expression e, func, da;
@@
(
-\(e.function\|e->function\) = func;
-\(e.data\|e->data\) = da;
|
-\(e.data\|e->data\) = da;
-\(e.function\|e->function\) = func;
)
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@match_function_and_data_after_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
... when != func = e2
when != da = e3
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
@match_function_and_data_before_init_timer@
expression e, e2, e3, e4, e5, func, da;
@@
(
-e.function = func;
... when != da = e4
-e.data = da;
|
-e->function = func;
... when != da = e4
-e->data = da;
|
-e.data = da;
... when != func = e5
-e.function = func;
|
-e->data = da;
... when != func = e5
-e->function = func;
)
... when != func = e2
when != da = e3
-init_timer
+setup_timer
( \(&e\|e\)
+, func, da
);
@r1 exists@
expression t;
identifier f;
position p;
@@
f(...) { ... when any
init_timer@p(\(&t\|t\))
... when any
}
@r2 exists@
expression r1.t;
identifier g != r1.f;
expression e8;
@@
g(...) { ... when any
\(t.data\|t->data\) = e8
... when any
}
// It is dangerous to use setup_timer if data field is initialized
// in another function.
@script:python depends on r2@
p << r1.p;
@@
cocci.include_match(False)
@r3@
expression r1.t, func, e7;
position r1.p;
@@
(
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
... when != func = e7
-t.function = func;
|
-t.function = func;
... when != func = e7
-init_timer@p(&t);
+setup_timer(&t, func, 0UL);
|
-init_timer@p(t);
+setup_timer(t, func, 0UL);
... when != func = e7
-t->function = func;
|
-t->function = func;
... when != func = e7
-init_timer@p(t);
+setup_timer(t, func, 0UL);
)
Signed-off-by: Kees Cook <keescook@chromium.org>
-----BEGIN PGP SIGNATURE-----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=xVV2
-----END PGP SIGNATURE-----
Merge tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.15.
Core:
- Atomic object lifetime fixes
- Atomic iterator improvements
- Sparse/smatch fixes
- Legacy kms ioctls to be interruptible
- EDID override improvements
- fb/gem helper cleanups
- Simple outreachy patches
- Documentation improvements
- Fix dma-buf rcu races
- DRM mode object leasing for improving VR use cases.
- vgaarb improvements for non-x86 platforms.
New driver:
- tve200: Faraday Technology TVE200 block.
This "TV Encoder" encodes a ITU-T BT.656 stream and can be found in
the StorLink SL3516 (later Cortina Systems CS3516) as well as the
Grain Media GM8180.
New bridges:
- SiI9234 support
New panels:
- S6E63J0X03, OTM8009A, Seiko 43WVF1G, 7" rpi touch panel, Toshiba
LT089AC19000, Innolux AT043TN24
i915:
- Remove Coffeelake from alpha support
- Cannonlake workarounds
- Infoframe refactoring for DisplayPort
- VBT updates
- DisplayPort vswing/emph/buffer translation refactoring
- CCS fixes
- Restore GPU clock boost on missed vblanks
- Scatter list updates for userptr allocations
- Gen9+ transition watermarks
- Display IPC (Isochronous Priority Control)
- Private PAT management
- GVT: improved error handling and pci config sanitizing
- Execlist refactoring
- Transparent Huge Page support
- User defined priorities support
- HuC/GuC firmware refactoring
- DP MST fixes
- eDP power sequencing fixes
- Use RCU instead of stop_machine
- PSR state tracking support
- Eviction fixes
- BDW DP aux channel timeout fixes
- LSPCON fixes
- Cannonlake PLL fixes
amdgpu:
- Per VM BO support
- Powerplay cleanups
- CI powerplay support
- PASID mgr for kfd
- SR-IOV fixes
- initial GPU reset for vega10
- Prime mmap support
- TTM updates
- Clock query interface for Raven
- Fence to handle ioctl
- UVD encode ring support on Polaris
- Transparent huge page DMA support
- Compute LRU pipe tweaks
- BO flag to allow buffers to opt out of implicit sync
- CTX priority setting API
- VRAM lost infrastructure plumbing
qxl:
- fix flicker since atomic rework
amdkfd:
- Further improvements from internal AMD tree
- Usermode events
- Drop radeon support
nouveau:
- Pascal temperature sensor support
- Improved BAR2 handling
- MMU rework to support Pascal MMU
exynos:
- Improved HDMI/mixer support
- HDMI audio interface support
tegra:
- Prep work for tegra186
- Cleanup/fixes
msm:
- Preemption support for a5xx
- Display fixes for 8x96 (snapdragon 820)
- Async cursor plane fixes
- FW loading rework
- GPU debugging improvements
vc4:
- Prep for DSI panels
- fix T-format tiling scanout
- New madvise ioctl
Rockchip:
- LVDS support
omapdrm:
- omap4 HDMI CEC support
etnaviv:
- GPU performance counters groundwork
sun4i:
- refactor driver load + TCON backend
- HDMI improvements
- A31 support
- Misc fixes
udl:
- Probe/EDID read fixes.
tilcdc:
- Misc fixes.
pl111:
- Support more variants
adv7511:
- Improve EDID handling.
- HDMI CEC support
sii8620:
- Add remote control support"
* tag 'drm-for-v4.15' of git://people.freedesktop.org/~airlied/linux: (1480 commits)
drm/rockchip: analogix_dp: Use mutex rather than spinlock
drm/mode_object: fix documentation for object lookups.
drm/i915: Reorder context-close to avoid calling i915_vma_close() under RCU
drm/i915: Move init_clock_gating() back to where it was
drm/i915: Prune the reservation shared fence array
drm/i915: Idle the GPU before shinking everything
drm/i915: Lock llist_del_first() vs llist_del_all()
drm/i915: Calculate ironlake intermediate watermarks correctly, v2.
drm/i915: Disable lazy PPGTT page table optimization for vGPU
drm/i915/execlists: Remove the priority "optimisation"
drm/i915: Filter out spurious execlists context-switch interrupts
drm/amdgpu: use irq-safe lock for kiq->ring_lock
drm/amdgpu: bypass lru touch for KIQ ring submission
drm/amdgpu: Potential uninitialized variable in amdgpu_vm_update_directories()
drm/amdgpu: potential uninitialized variable in amdgpu_vce_ring_parse_cs()
drm/amd/powerplay: initialize a variable before using it
drm/amd/powerplay: suppress KASAN out of bounds warning in vega10_populate_all_memory_levels
drm/amd/amdgpu: fix evicted VRAM bo adjudgement condition
drm/vblank: Tune drm_crtc_accurate_vblank_count() WARN down to a debug
drm/rockchip: add CONFIG_OF dependency for lvds
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CEC framework needs to know when the hotplug detect signal
disappears, since that means the CEC physical address has to be
invalidated (i.e. set to f.f.f.f).
Add a lost_hotplug op that is called when the HPD signal goes away.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Hook up the HDMI CEC support in the hdmi4 driver.
It add the CEC irq handler, the CEC (un)init calls and tells the CEC
implementation when the physical address changes.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add the source and header for the OMAP4 HDMI CEC support.
This code is not yet hooked up, that will happen in the next patch.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The hdmi_power_on/off_core functions can be called multiple times:
when the HPD changes and when the HDMI CEC support needs to power
the HDMI core.
So use a counter to know when to really power on or off the HDMI core.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Call hdmi4_core_powerdown_disable() in hdmi_power_on_core() to
power up the HDMI core (needed for CEC). The same call can now be dropped
in hdmi4_configure().
Signed-off-by: Hans Verkuil <hansverk@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pass struct omap_hdmi to the irq handler since it will need access
to hdmi.core.
Do not clear the IRQ_HDMI_CORE bit: that will be controlled by the
HDMI CEC code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Three low-level functions in hdmi4.c and hdmi4_core.c are
made available for use by the OMAP4 CEC support.
Renamed the prefix to hdmi4 since these are OMAP4 specific.
These function deal with the HDMI core and are needed to
power it up for use with CEC, even when the HPD is low.
Background: even if the HPD is low it should still be possible
to use CEC. Some displays will set the HPD low when they go into standby or
when they switch to another input, but CEC is still available and able
to wake up/change input for such a display.
This is explicitly allowed by the CEC standard.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Extend the hdmi_core_data struct with the additional fields needed
for CEC.
Also fix a simple typo in a comment.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
For OMAP4 CEC support the CEC pin should always be on. So keep
ls_oe_gpio high all the time in order to support CEC.
Background: even if the HPD is low it should still be possible
to use CEC. Some displays will set the HPD low when they go into standby or
when they switch to another input, but CEC is still available and able
to wake up/change input for such a display.
This is explicitly allowed by the CEC standard.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Seems that on omap3 enabling a crtc without any planes causes a sync
lost flood. This only happens on the first enable, and after that it
works. This looks like an HW issue and it's unclear why this is
happening or how to fix it.
This started happening after 897145d0c7
("drm/omapdrm: Move commit_modeset_enables() before commit_planes()")
which, as a work-around, changed omapdrm first to do the modeset enable,
and plane set only after that. This WA should be fine on all DSS
versions, but apparently OMAP3 DSS is an exception.
This patch reverts that work-around for OMAP3 DSS.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
7d267f068a ("drm/omap: work-around for
errata i886") changed how the PLL dividers and multipliers are
calculated. While the new way should work fine for all the PLLs, it
breaks omap5 PLLs. The issues seen are rather odd: seemed that the
output clock rate is half of what we asked. It is unclear what's causing
there issues.
As a work-around this patch adds a "errata_i886" flag, which is set only
for DRA7's PLLs, and the PLL setup is done according to that flag.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
omapdrm rejects all venc (analog tv-out) videomodes, due to somewhat
strict checking of the values, making tv-out unusable.
We only support two videomodes, one for PAL and one for NTSC, so instead
of trying to check every field in the videomode struct, this patch makes
the driver check only the pixel clock and the size of the display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
