A collection of fixes since the merge window, mostly driver specific but
there's a few in the core that clean up fallout from the refactorings
done in the last cycle.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl34w3ITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0FM/B/9zM8zae1DIXi10S7tRElz/LnadE7il
umQ34PoghSd/f9D5TCQZMgyLjdglyQGiOar4G1xkOEC87yjBCY8AOfcV3QQLRsgK
ej8AdrBGKQUWvCdoJGx/FsrwTpgBcvRNvVJbHIKab2BfGxZA8t733tMCAkuXHnty
/dtYhA5wjI6gGtUofihEp9jvVuRLWFjopaUJs4JANKO5pmRfXgzdayt74xUKz2/q
VQCp2dCmCSXSIyYUwoY/Dg9+3RQ6Ebt3YfSWBGUrxyW+EyYtCGz4lHzV3Wb+QThM
daV+wHXlz0vW4Zr6rUz6D6WlyiK9IlhEX+hdYJagFnHmKXNcpHHl2LvU
=sP7K
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v5.5-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.5
A collection of fixes since the merge window, mostly driver specific but
there's a few in the core that clean up fallout from the refactorings
done in the last cycle.
The simple-card tries to signal the codec to disable rate constraints,
see commit 2458adb8f9 ("SoC: simple-card-utils: set 0Hz to sysclk when
shutdown"). This wasn't handled by the codec, instead it would set the
FLL frequency to 0Hz which isn't working. Since we don't have any rate
constraints just ignore this request.
Fixes: 13409d27cb ("ASoC: wm8904: configure sysclk/FLL automatically")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191122232532.22258-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
The current code assumes that the power is turned off in
SND_SOC_BIAS_OFF. If there are no actual regulator the codec isn't
turned off and the registers are not reset to their default values but
the regcache is still marked as dirty. Thus a value might not be written
to the hardware if it is set to the default value. Do a software reset
before turning off the power to make sure the registers are always reset
to their default states.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191112223629.21867-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds a new mode WM8904_CLK_AUTO which automatically enables the FLL
if a frequency different than the MCLK is set.
These additions make the codec work with the simple-card driver in
general and especially in systems where the MCLK doesn't match the
required clock.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20191108203152.19098-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MCLK input is needed when accessing any register after enabling SYSCLK.
This also fixes imbalance of clk_enable / clk_disable when transitioning
between ON -> STANDBY -> ON bias levels.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Save 2x unsigned int of .rodata.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
module.h already contained moduleparam.h, so it is safe to remove
the redundant include.
The issue is detected with the help of Coccinelle.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115042 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Trivial fix to spelling mistake in SOC_ENUM literal string
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Check for snd_soc_codec_driver structures that are only passed to
snd_soc_register_codec or memcpy (2nd arg), for which the corresponding
parameters are declared const. Declare as const snd_soc_codec_driver
structures that have these properties.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct snd_soc_codec_driver i@p = { ... };
@ok@
identifier r.i;
expression e1,e2,e3;
position p;
@@
(
snd_soc_register_codec(e1,&i@p,e2,e3)
|
memcpy(e1,&i@p,e2)
)
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct snd_soc_codec_driver i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"DRC Mode" and "EQ Mode" ctls in wm8904 codec driver are enum, while
the current driver accesses wrongly via value.integer.value[]. They
have to be via value.enumerated.item[] instead.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We try to check that "deemph" is zero or one, but because of an
underflow bug, it can also be negative. It's fine, negative values are
handled as non-zero. But it's messy and static checkers complain so
let's fix it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dapm field of the snd_soc_codec struct is eventually going to be
removed, in preparation for this replace all manual access to
codec->dapm.bias_level with snd_soc_codec_get_bias_level() and replace all
other manual access to codec->dapm with snd_soc_codec_get_dapm().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All drivers have the same line at the end of the set_bias_level callback to
update the bias_level state. Move this update into
snd_soc_dapm_force_bias_level() and remove them from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The WM8904 and WM8918 has the same data type, while the WM8912
has different data type. So, use the data in dt ids table to
distinguish them.
Signed-off-by: Alexander Morozov <linux@meltdown.ru>
[voice.shen@atmel.com: add code to distinguish device type]
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the path name for mux to get rid of the following warning:
--->8---
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTL
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTL
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTL
wm8904 1-001a: Control not supported for path ADCL -> [Left] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCL --> Left --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCL -> Left -> AIFOUTR
wm8904 1-001a: Control not supported for path ADCR -> [Right] -> AIFOUTR
wm8904 1-001a: ASoC: no dapm match for ADCR --> Right --> AIFOUTR
wm8904 1-001a: ASoC: Failed to add route ADCR -> Right -> AIFOUTR
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACL
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACL
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACL
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACL
wm8904 1-001a: Control not supported for path AIFINR -> [Right] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINR --> Right --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINR -> Right -> DACR
wm8904 1-001a: Control not supported for path AIFINL -> [Left] -> DACR
wm8904 1-001a: ASoC: no dapm match for AIFINL --> Left --> DACR
wm8904 1-001a: ASoC: Failed to add route AIFINL -> Left -> DACR
---8<---
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The CODEC doesn't care how data is laid out in memory.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For CODEC controls snd_kcontrol_chip() currently returns a pointer to the
CODEC that registered the control. With the upcoming consolidation of
platform and CODEC controls this will change. Prepare for this by introducing
the snd_soc_kcontrol_codec() helper function that will hide the implementation
details of how the CODEC for a control can be obtained. This will allow us to
change this easily in the future.
The patch also updates all CODEC drivers to use the new helper function.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For some CODEC drivers like who act as the MFDs children are ignored
by this patch.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just replace with the helper macro. No functional change at all.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The name "max" in struct soc_enum is rather confusing since it
actually takes the number of items. With "max", one might try to
assign (nitems - 1) value.
Rename the field to a more appropriate one, "items", which is also
used in struct snd_ctl_elem_info, too.
This patch also rewrites some code like "if (x > e->nitems - 1)" with
"if (x >= e->nitems)". Not only the latter improves the readability,
it also fixes a potential bug when e->items is zero.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When wm8904 work in DSP mode B, we still need to configure it to
work in DSP mode. Or else, it will work in Right Justified mode.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
BUG() used in the driver is just to spit the stack trace on buggy
points, not really needed to stop the whole operation. For that
purpose, it'd be more convenient to use WARN() instead with more
error information.
Cc: patches@opensource.wolfsonmicro.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The core will call snd_soc_dapm_new_widgets() once all components of the card
have been initialized, so there is no need to do this manually in the driver.
Calling it earlier also might result in a partially instantiated system being
powered up which cause undesired side effects.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The core_intercon is added two times, remove the redundant one
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
