Node name should be generic, use "reset-controller" instead of "src" for
i.MX6/i.MX7 SoCs src nodes.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the missing input mux for ENET2 mdio. Without this setting, it is not
possible to read the MDIO answers back from the PHY.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although ocotp clock is always ON for i.MX6SL, OCOTP can be
accessed directly, but since i.MX6SL nvmem interface is supported,
and fsl,tempmon-data is deprecated, use it instead of getting fuse
data by reading ocotp directly, this makes all i.MX6 SoCs aligned.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Although ocotp clock is always ON for i.MX6QDL, OCOTP can be
accessed directly, but since i.MX6QDL nvmem interface is supported,
and fsl,tempmon-data is deprecated, use it instead of getting fuse
data by reading ocotp directly, this makes all i.MX6 SoCs aligned.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Connect the wl_reg regulator to usdhc2 such that it can be enabled
and disabled as needed. There is no need for this to be always-on.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Sterling-LWB has a BCM4330 which has a UART based bluetooth
HCI. Add support for binding to the bcm_hci driver to take care
of handling the shutdown gpio and loading firmware.
Because the shutdown gpio is more of an enable than a regulator
go ahead and replace the regulator with a shutdown-gpio.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add one node for the accel/gyro i2c device and another for the separate
magnetometer device in the lsm9ds1.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Interrupt is a required property according to SRC binding, add
it for SRC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Interrupt is a required property according to SRC binding, add
it for SRC node.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The iomuxc-gpr node is not used and causes the following dtc
warning with W=1:
arch/arm/boot/dts/imx50.dtsi:286.28-289.6: Warning (unique_unit_address): /soc/bus@50000000/iomuxc@53fa8000: duplicate unit-address (also used in node /soc/bus@50000000/iomuxc-gpr@53fa8000)
Remove the node to fix the warning.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW552x-B board revision adds USB OTG support.
Enable the device-tree node and configure the OTG_ID pin.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add ethernet PHY configuration ahead of removing the quirk that
configures the clocking mode for the PHY. The RGMII delay is
already set correctly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1021A-TWR has one micron "n25q128a13" flash of size 16M.
Add QSPI node properties for it.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since the PMIC driver now has IRQ handling, add the GPIO to
listen to things like RTC alarm or ADC conversion completion.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Introduce dtsi with overlay configuration for enabling UHS-I
for Colibri iMX6S/DL V1.1x re-design.
2. Introduce new dts for the Colibri iMX6S/DL V1.1x
on Colibri Evaluation Carrier Board V3.x. However, disable 1.8V for
the Colibri Evaluation Board since this carrier board has 3.3V pull-ups on.
3. Provide proper configuration for VGEN3, which allows that rail to
be automatically switched to 1.8 volts for proper UHS-I operation mode.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each cpu-core is supposed to list its supply separately, add
supply for cpu1.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX7 uses cpufreq-dt driver which requires the CPU supply name to be
either "cpu0-supply" or "cpu-supply", correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add DT bits to support the DH 560-200 display unit, which can be plugged
into the side of the PDK2 board. The display unit contains a display, EDT
ETM0700G0EDH6 and an EDT FT5x06 touchscreen controller.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
To: linux-arm-kernel@lists.infradead.org
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most of the commits are for additional hardware support and minor fixes
for existing machines for all the usual platforms: qcom, amlogic, at91,
gemini, mediatek, ti, socfpga, i.mx, layerscape, uniphier, rockchip,
exynos, ux500, mvebu, tegra, stm32, renesas, sunxi, broadcom, omap,
and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation.
Andre Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into
dts files, for many devices that relied on a mix of auxiliary data
in addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants, along
with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based on
the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAl6HpMkACgkQmmx57+YA
GNkGsQ/+KRbE74XGQvZww5PleaesqoZZhrt2gbi0pEJZ/JTgNa3dBkT+JwlToe/H
x7nFVfMZeEl4O9GO0+/CH2tsmQa5BA8R9JddhFxwnZ48ZYLQAdaukwt94LM2zj3K
GFgs47N4DAAF5QJoXNtmmQCXUWbj7A/0S5TTpXe94TYPN9XiJCdsyNNLpW3undTe
K1HLnd4yWGforQc/VfRsV/Gsqi1VNHgL34M3belahiG7x0lytJDCHfhsfmIdxdGR
n3LVRRJr6NhKcuUw3XtA8MxT4dTAcgHjbbDLkS/b1nHfuXMi0/zW8VPBzD/xyHL7
fbFl8ayUMANB6FD/U7ptUC/0IMXuHDUn4B60CEEzK8ddkEbErrmXlYVGogpFHxvm
MqrW8CnO0YEr0YMNAIyZoqHYGq8+8DCq+SRH48brdPzuiKI6OahdV1o07ulGhOjq
ihwoZNE+J0NjeaX7C1xBX3DT1XqdcNPCmu3gx6r06u2FVXVm1J19YkIzQnEXQvKy
NRIw5LIOfEsxkMSQ0oUuAUUUY1Fq1zuHqD8MmgBd3jqIULQqgfahmPL6Dtwm5QFf
R17YsMcQ7ae1Pp7a+D3Jrkbn+s2y8wmJZIqH3eWebps9RvpWmrxzsRfOJ2czhqM1
NY7Z/TGMM7lGM75DZ+xskfk7UCAX+hqMSTiNg9xbRo8946GAbV4=
=ye2F
-----END PGP SIGNATURE-----
Merge tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
Here are 3 SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your current
tree, that should be trivial to handle (one file modified by two things,
one file deleted.)
All 3 of these have been in linux-next for a while, with no reported
issues other than the merge conflict.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXodg5A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykySQCgy9YDrkz7nWq6v3Gohl6+lW/L+rMAnRM4uTZm
m5AuCzO3Azt9KBi7NL+L
=2Lm5
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
-----BEGIN PGP SIGNATURE-----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=db/l
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
MAINTAINERS: drop an old reference to stm32 pwm timers doc
MAINTAINERS: dt: update etnaviv file reference
dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
dt-bindings: uniphier-system-bus: fix warning in the example
dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
dt-bindings: power: Fix example for power-domain
dt-bindings: arm: Add some constraints for PSCI nodes
of: some unittest overlays not untracked
of: gpio unittest kfree() wrong object
dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
dt-bindings: serial: sh-sci: Convert to json-schema
dt-bindings: serial: Document serialN aliases
dt-bindings: thermal: tsens: Set 'additionalProperties: false'
dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
dt-bindings: vendor-prefixes: Add Beacon vendor prefix
dt-bindings: vendor-prefixes: Add Topwise
of: of_private.h: Replace zero-length array with flexible-array member
docs: dt: fix a broken reference to input.yaml
docs: dt: fix references to ap806-system-controller.txt
...
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and some
vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHT8w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yl3CwCgj/97IKb4K49nV2rDgiV+t/ELWqUAnjBp+Zpd
H2BEdhwCFhq/5CJHKXWH
=JTm1
-----END PGP SIGNATURE-----
Merge tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
Pull EFI updates from Ingo Molnar:
"The EFI changes in this cycle are much larger than usual, for two
(positive) reasons:
- The GRUB project is showing signs of life again, resulting in the
introduction of the generic Linux/UEFI boot protocol, instead of
x86 specific hacks which are increasingly difficult to maintain.
There's hope that all future extensions will now go through that
boot protocol.
- Preparatory work for RISC-V EFI support.
The main changes are:
- Boot time GDT handling changes
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file
I/O, memory allocation, etc.
- Introduce a generic initrd loading method based on calling back
into the firmware, instead of relying on the x86 EFI handover
protocol or device tree.
- Introduce a mixed mode boot method that does not rely on the x86
EFI handover protocol either, and could potentially be adopted by
other architectures (if another one ever surfaces where one
execution mode is a superset of another)
- Clean up the contents of 'struct efi', and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit
firmware implementations to return EFI_UNSUPPORTED from UEFI
runtime services at OS runtime, and expose a mask of which ones are
supported or unsupported via a configuration table.
- Partial fix for the lack of by-VA cache maintenance in the
decompressor on 32-bit ARM.
- Changes to load device firmware from EFI boot service memory
regions
- Various documentation updates and minor code cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
efi/libstub/arm: Fix spurious message that an initrd was loaded
efi/libstub/arm64: Avoid image_base value from efi_loaded_image
partitions/efi: Fix partition name parsing in GUID partition entry
efi/x86: Fix cast of image argument
efi/libstub/x86: Use ULONG_MAX as upper bound for all allocations
efi: Fix a mistype in comments mentioning efivar_entry_iter_begin()
efi/libstub: Avoid linking libstub/lib-ksyms.o into vmlinux
efi/x86: Preserve %ebx correctly in efi_set_virtual_address_map()
efi/x86: Ignore the memory attributes table on i386
efi/x86: Don't relocate the kernel unless necessary
efi/x86: Remove extra headroom for setup block
efi/x86: Add kernel preferred address to PE header
efi/x86: Decompress at start of PE image load address
x86/boot/compressed/32: Save the output address instead of recalculating it
efi/libstub/x86: Deal with exit() boot service returning
x86/boot: Use unsigned comparison for addresses
efi/x86: Avoid using code32_start
efi/x86: Make efi32_pe_entry() more readable
efi/x86: Respect 32-bit ABI in efi32_pe_entry()
efi/x86: Annotate the LOADED_IMAGE_PROTOCOL_GUID with SYM_DATA
...
Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids, and
other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXoHL9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymz6wCcDwDTZouXj+0B37q+kwlCQQPyLukAn2CxKfrM
d+wScRHWoZutA8IdzqaU
=5+jn
-----END PGP SIGNATURE-----
Merge tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids,
and other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (239 commits)
USB: cdc-acm: restore capability check order
usb: cdns3: make signed 1 bit bitfields unsigned
usb: gadget: fsl: remove unused variable 'driver_desc'
usb: gadget: f_fs: Fix use after free issue as part of queue failure
usb: typec: Correct the documentation for typec_cable_put()
USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
USB: serial: option: add Wistron Neweb D19Q1
USB: serial: option: add BroadMobi BM806U
USB: serial: option: add support for ASKEY WWHC050
usb: core: Add ACPI support for USB interface devices
driver core: platform: Reimplement devm_platform_ioremap_resource
usb: dwc2: convert to devm_platform_get_and_ioremap_resource
usb: host: hisilicon: convert to devm_platform_get_and_ioremap_resource
usb: host: xhci-plat: convert to devm_platform_get_and_ioremap_resource
drivers: provide devm_platform_get_and_ioremap_resource()
phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
...
Until now a PHY-fixup in mach-imx set our rgmii timing correctly. For
the PHY KSZ9131 there is no PHY-fixup in mach-imx. To support this PHY
too, use rgmii-id.
For the now used KSZ9031 nothing will change, as rgmii-id is only
implemented and supported by the KSZ9131.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and a
few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the timings
for the NAND flash on the Nokia N900 that regressed a while ago after
the move to configuring them from DT. Some other OMAPs now set the
correct dma limits on the L3 bus, and a regression fix addresses lost
Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel
power supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC,
this is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data when
mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver
-----BEGIN PGP SIGNATURE-----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=31+Z
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM DT and driver fixes from Arnd Bergmann:
"For the devicetree files, there are a total of 20 patches, almost
entirely for 32-bit machines:
- The Allwinner/sun9i r40 SoC dtsi file contains a number of issues,
both for correctness and for style that are addressed in separate
patches. This causes most of the changed lines of the DT updates
this time.
- More Allwinner updates fixing the identification of the security
system on sun8i/A33, a recent regression of the A83t ethernet, and
a few board specific issues on the TBS-A711 macine.
- Several bug fixes for OMAP dts files, most notably fixing the
timings for the NAND flash on the Nokia N900 that regressed a while
ago after the move to configuring them from DT. Some other OMAPs
now set the correct dma limits on the L3 bus, and a regression fix
addresses lost Ethernet on dm814x
- One incorrect setting in the newly added Raspberry Pi Zero W that
may cause issues with the SD card controller.
- A missing property on the bcm2835 firmware node caused incorrect
DMA settings.
- An old bug on the oxnas platform causing spurious interrupts is
finally addressed.
- A regression on the Exynos Midas board broke the OLED panel power
supply.
- The i.MX6 phycore SoM specified the wrong voltage for the SoC, this
is now set to the values from the datasheet.
- Some 64-bit machines use a deprecated string to identify the PSCI
firmware.
There are also several small code fixes addressing mostly serious
issues:
- Fix the sunxi rsb bus access to no longer return incorrect data
when mixing 8 and 16 bit I/O.
- Fix a suspend/resume regression on the OMAP2+ lcdc from a missing
quirk in the ti-sysc driver
- Fix a NULL pointer access from a race in the fsl dpio driver
- Fix a v5.5 regression in the exynos-chipid driver that caused an
invalid error code probing the device on non-exynos platforms
- Fix an out-of-bounds access in the AMD TEE driver"
* tag 'arm-soc-fixes-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (24 commits)
soc: samsung: chipid: Fix return value on non-Exynos platforms
arm64: dts: Fix leftover entry-methods for PSCI
ARM: dts: exynos: Fix regulator node aliasing on Midas-based boards
ARM: dts: oxnas: Fix clear-mask property
ARM: dts: bcm283x: Fix vc4's firmware bus DMA limitations
ARM: dts: omap5: Add bus_dma_limit for L3 bus
ARM: dts: omap4-droid4: Fix lost touchscreen interrupts
ARM: dts: dra7: Add bus_dma_limit for L3 bus
ARM: bcm2835-rpi-zero-w: Add missing pinctrl name
ARM: dts: sun8i: a33: add the new SS compatible
dt-bindings: crypto: add new compatible for A33 SS
ARM: dts: sun8i: r40: Move SPI device nodes based on address order
ARM: dts: sun8i: r40: Fix register base address for SPI2 and SPI3
ARM: dts: sun8i: r40: Move AHCI device node based on address order
ARM: dts: imx6: phycore-som: fix arm and soc minimum voltage
soc: fsl: dpio: register dpio irq handlers after dpio create
tee: amdtee: out of bounds read in find_session()
ARM: dts: N900: fix onenand timings
bus: ti-sysc: Fix quirk flags for lcdc on am335x
ARM: dts: Fix dm814x Ethernet by changing to use rgmii-id mode
...
I renamed the dsi-nodes from dsi@ to dsi-controller@
so that the schema check would kick in, but missed to
rename it in a few places.
Link: https://lore.kernel.org/r/20200326222536.86441-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With a non-critical clock fix for dm814x ethernet, we can update ti81xx
for cpsw ethernet and edma to probe them with ti-sysc interconnect
target module driver and device tree data. And we can drop the related
remaining platform data for cpsw and edma.
-----BEGIN PGP SIGNATURE-----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=EDSy
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-drop-pdata-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Drop remaining legacy platform data for cpsw and edma
With a non-critical clock fix for dm814x ethernet, we can update ti81xx
for cpsw ethernet and edma to probe them with ti-sysc interconnect
target module driver and device tree data. And we can drop the related
remaining platform data for cpsw and edma.
* tag 'omap-for-v5.7/ti-sysc-drop-pdata-ti81xx-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Drop legacy platform data for ti81xx edma
ARM: dts: Configure interconnect target module for ti816x edma
ARM: dts: Configure interconnect target module for dm814x tptc3
ARM: dts: Configure interconnect target module for dm814x tptc2
ARM: dts: Configure interconnect target module for dm814x tptc1
ARM: dts: Configure interconnect target module for dm814x tptc0
ARM: dts: Configure interconnect target module for dm814x tpcc
ARM: OMAP2+: Drop legacy platform data for dm814x cpsw
ARM: dts: Configure interconnect target module for dm814x cpsw
clk: ti: Fix dm814x clkctrl for ethernet
Link: https://lore.kernel.org/r/pull-1584575307-189595@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This series of changes continues dropping legacy platform data for
omaps by updating devices to probe with ti-sysc interconnect target
module driver:
- Update omap4, omap5, am437x, and dra7 display subsystem (DSS)
to probe with device tree data only
- Update am335x, am437x and dra7 to probe EDMA to probe with
device tree data only
- Drop legacy platform data for am335x and am437x PRUSS as the
current code just keeps the devices in reset
- Drop legacy platform data for omap4 DSP and IPU as the current
code just keeps the devices in reset
- Configure am437x and dra7 PRU-ICSS to probe with device tree
data
For the dropped omap4 DSP and IPU platform data, there will be patches
coming later on to configure the accelerators using the omap remoteproc
bindings so hopefully folks can actually use these devices eventually.
-----BEGIN PGP SIGNATURE-----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=QqzI
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v5.7/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/late
Drop legacy platform data for omaps for v5.7
This series of changes continues dropping legacy platform data for
omaps by updating devices to probe with ti-sysc interconnect target
module driver:
- Update omap4, omap5, am437x, and dra7 display subsystem (DSS)
to probe with device tree data only
- Update am335x, am437x and dra7 to probe EDMA to probe with
device tree data only
- Drop legacy platform data for am335x and am437x PRUSS as the
current code just keeps the devices in reset
- Drop legacy platform data for omap4 DSP and IPU as the current
code just keeps the devices in reset
- Configure am437x and dra7 PRU-ICSS to probe with device tree
data
For the dropped omap4 DSP and IPU platform data, there will be patches
coming later on to configure the accelerators using the omap remoteproc
bindings so hopefully folks can actually use these devices eventually.
* tag 'omap-for-v5.7/ti-sysc-drop-pdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (56 commits)
ARM: OMAP2+: Drop legacy platform data for dra7 edma
ARM: OMAP2+: Drop legacy platform data for am3 and am4 edma
ARM: dts: Configure interconnect target module for dra7 tptc1
ARM: dts: Configure interconnect target module for dra7 tptc0
ARM: dts: Configure interconnect target module for dra7 tpcc
ARM: dts: Configure interconnect target module for am4 tptc2
ARM: dts: Configure interconnect target module for am4 tptc1
ARM: dts: Configure interconnect target module for am4 tptc0
ARM: dts: Configure interconnect target module for am4 tpcc
ARM: dts: Configure interconnect target module for am3 tptc2
ARM: dts: Configure interconnect target module for am3 tptc1
ARM: dts: Configure interconnect target module for am3 tptc0
ARM: dts: Configure interconnect target module for am3 tpcc
ARM: dts: dra7: Add PRU-ICSS interconnect target-module nodes
ARM: dts: AM4372: Add the PRU-ICSS interconnect target-module node
ARM: dts: AM33xx-l4: Update PRUSS interconnect target-module node
ARM: OMAP2+: Drop legacy platform data for am437x DSS
ARM: OMAP2+: Drop legacy platform data for dra7 DSS
ARM: OMAP2+: Drop legacy platform data for omap5 DSS
ARM: OMAP2+: Drop legacy platform data for omap4 dss
...
Link: https://lore.kernel.org/r/pull-1583858385-416921@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
For proper bindings checks we need to properly group the port-phys and
sgpio-gpio items, so that they match the expected number of items.
Link: https://lore.kernel.org/r/20200228135106.220620-5-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently multiple interrupts for some devices are written as one array
instead of using the DT grouping notation (<0 42 4>, <0 23 4>).
This ends up in the same binary representation in the .dtb, but is
semantically not equivalent. The yaml schema checks will stumble over
this, so lets fix that first.
I refrained from using the symbolic names for GIC_SPI/GIC_PPI and
IRQ_TYPE_LEVEL_HIGH, mostly because it increases the delta between the
original DTS files and the mainline versions, so it's just additional
churn.
Link: https://lore.kernel.org/r/20200228135106.220620-4-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The PL011 UART binding requires two clocks to be named in a node.
Add the second clock, which is the bus gate, that just gets enabled.
Since this is a fixed clock anyway, it doesn't make any difference.
Link: https://lore.kernel.org/r/20200228135106.220620-3-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The .dts files for the Calxeda machines are quite old, so carry some
sloppy mistakes that the DT schema checker will complain about.
Fix those issues, they should not have any effect on functionality.
Link: https://lore.kernel.org/r/20200228135106.220620-2-andre.przywara@arm.com
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds Bluetooth support on Nexus 5, USB on Xperia Z1 and defines
gpio-ranges throughout the various gpio-controllers.
-----BEGIN PGP SIGNATURE-----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=1cGm
-----END PGP SIGNATURE-----
Merge tag 'qcom-dts-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/dt
Qualcomm ARM dts updates for v5.7
This adds Bluetooth support on Nexus 5, USB on Xperia Z1 and defines
gpio-ranges throughout the various gpio-controllers.
* tag 'qcom-dts-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: add gpio-ranges property
ARM: dts: qcom: msm8974-hammerhead: add support for bluetooth
ARM: dts: qcom: msm8974: add blsp2_uart10
ARM: dts: qcom: msm8974-honami: Add USB node.
Link: https://lore.kernel.org/r/20200318044305.GE470201@yoga
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Rename the IDE nodes to match the YAML schema
- Add a temperature zone to the DIR-685, use hard drive
as sensor and cool the case using the fan.
-----BEGIN PGP SIGNATURE-----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=/Tw7
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
Gemini DTS changes for v5.7:
- Rename the IDE nodes to match the YAML schema
- Add a temperature zone to the DIR-685, use hard drive
as sensor and cool the case using the fan.
* tag 'gemini-dts-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
Link: https://lore.kernel.org/r/CACRpkdbvgqCVuoMCHJrCZ0J+3NrwdrBnwBz+BJrSE=hqYh2j+Q@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- New support for i.MX6/7 based PICO devices and Toradex i.MX7 based
Aster boards.
- Add voltage monitor device node for vf610-zii boards.
- Improve UART pins macro defines for i.MX6SX SoC and switch related
boards to use the new names.
- Use generic node name for devices like GPT, KPP, CCM, WDOG, OCOTP and
IOMUXC in i.MX DTS files.
- Switch imx6ul-pico device tree to DRM bindings.
- Use SPDX-License-Identifier for all Toradex i.MX6/7 based boards.
- Add proper rgmii PHY description for imx6dl-riotboard and
imx6q-marsboard.
- Add capture-subsystem device support for i.MX51.
- Kill off "simple-panel" compatibles which has never been an accepted
as an upstream compatible string.
- Random device addition to various boards.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAl5xkLsUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM5UZwgAh4EMxfFHTvfIO3Pobcax9qTnwQfX
A1cNE5VcZFhIt93FHV9H4k/rd/28v1QArs18X2PsdYk9NChzmEXSH1fPUQj7aMxT
NnDMDrkPaVGezWZbtoUEcpYr9sCxS6c0eMXq/VI2TTZS0pWPTzBBtsyqWiPbx3ZN
4h12SjS8T3M81VI90En1QStFAlg0YnDXYdEHNS3c/0rBcXLenkfPMlAeBJw6Rti2
9simCtJEDYnJpN77JUfFz8Lkm1bc7np4Fr56diKOrOmCeXD9VQ/qyy/KyBu99oRN
SL404Y7ACFc1OG9MMTkCKrbSCCQqa5ZseNyvV7PJEZImZ3XNb59+ICidRQ==
=42du
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm DTS changes for 5.7:
- New support for i.MX6/7 based PICO devices and Toradex i.MX7 based
Aster boards.
- Add voltage monitor device node for vf610-zii boards.
- Improve UART pins macro defines for i.MX6SX SoC and switch related
boards to use the new names.
- Use generic node name for devices like GPT, KPP, CCM, WDOG, OCOTP and
IOMUXC in i.MX DTS files.
- Switch imx6ul-pico device tree to DRM bindings.
- Use SPDX-License-Identifier for all Toradex i.MX6/7 based boards.
- Add proper rgmii PHY description for imx6dl-riotboard and
imx6q-marsboard.
- Add capture-subsystem device support for i.MX51.
- Kill off "simple-panel" compatibles which has never been an accepted
as an upstream compatible string.
- Random device addition to various boards.
* tag 'imx-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (55 commits)
ARM: dts: imx6q-marsboard: properly define rgmii PHY
ARM: dts: imx6dl-riotboard: properly define rgmii PHY
ARM: dts: imx51-zii-rdu1: set name prefix for TPA6130A2
ARM: dts: imx6: RDU2: assign video PLL as input to LDB
ARM: dts: vf: toradex: SPDX tags and copyright cleanup
ARM: dts: imx7: toradex: use SPDX-License-Identifier
ARM: dts: imx6: toradex: use SPDX-License-Identifier
ARM: dts: imx51: add capture-subsystem device
ARM: dts: imx: add nvmem property for cpu0
ARM: dts: imx6qdl: Add imx6qdl-pico support
ARM: dts: imx6ul-pico: Add support for the dwarf baseboard
ARM: dts: imx7d-pico: Add support for the nymph baseboard
ARM: dts: imx7d-pico: Add support for the dwarf baseboard
ARM: dts: imx23: introduce mmc0_sck_cfg
ARM: dts: imx25-pinfunc: add config for kpp rows 4 to 7
ARM: dts: imx: align name for crypto node and child nodes
ARM: dts: imx6qdl-gw5910: add CC1352 UART
ARM: dts: imx6qdl-sr-som-ti: indicate powering off wifi is safe
ARM: dts: imx6: phycore-som: add da9062 gpio support
ARM: dts: imx6: phycore-som: explicit disable pmic watchdog during suspend
...
Link: https://lore.kernel.org/r/20200318051918.32579-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Rename nodes to avoid dt-schema warnings
- Add a generic compatible to EEPROM so that it matches OF table
- Add USB controller nodes to Pro5 SoC
- Fix clock and reset of SPI nodes
-----BEGIN PGP SIGNATURE-----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=posG
-----END PGP SIGNATURE-----
Merge tag 'uniphier-dt-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier into arm/dt
UniPhier ARM SoC DT updates for v5.7
- Rename nodes to avoid dt-schema warnings
- Add a generic compatible to EEPROM so that it matches OF table
- Add USB controller nodes to Pro5 SoC
- Fix clock and reset of SPI nodes
* tag 'uniphier-dt-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-uniphier:
ARM: dts: uniphier: Set SCSSI clock and reset IDs for each channel
ARM: dts: uniphier: Add USB3 controller nodes for Pro5
ARM: dts: uniphier: Add one more generic compatible string for I2C EEPROM
ARM: dts: uniphier: rename cache controller nodes to follow json-schema
ARM: dts: uniphier: rename NAND node names to follow json-schema
ARM: dts: uniphier: rename aidet node names to follow json-schema
ARM: dts: uniphier: change SD/eMMC node names to follow json-schema
Link: https://lore.kernel.org/r/CAK7LNAQ-AOTyqpV1E_S-hksjqexHfVauwGV9rrfDvjRVnu8-UQ@mail.gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
1. Various fixes:
- Reboot of some Odroid Exynos4412-based boards,
- MMC regulators on Arndale5250,
- Memory mapping on Artik5,
- GPU power domain on Exynos542x boards,
- LCD SPI polarity on UniversalC210,
2. Add thermal cooling of GPU on Odroid XU3/XU4 family,
3. Add dynamic-power-coefficient to Exynos5422 for energy model.
-----BEGIN PGP SIGNATURE-----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=6UVu
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/dt
Samsung DTS ARM changes for v5.7
1. Various fixes:
- Reboot of some Odroid Exynos4412-based boards,
- MMC regulators on Arndale5250,
- Memory mapping on Artik5,
- GPU power domain on Exynos542x boards,
- LCD SPI polarity on UniversalC210,
2. Add thermal cooling of GPU on Odroid XU3/XU4 family,
3. Add dynamic-power-coefficient to Exynos5422 for energy model.
* tag 'samsung-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix polarity of the LCD SPI bus on UniversalC210 board
ARM: dts: exynos: Fix G3D power domain supply on Arndale Octa boards
ARM: dts: exynos: Fix G3D power domain supply on Odroid XU3/XU4/HC1 boards
ARM: dts: exynos: Fix memory on Artik5 evaluation boards
ARM: dts: exynos: Make fixed regulators always-on on Arndale5250
ARM: dts: exynos: Fix MMC regulator on Arndale5250 board
ARM: dts: exynos: Add dynamic-power-coefficient to Exynos5422 CPUs
ARM: dts: exynos: Add GPU thermal zone cooling maps for Odroid XU3/XU4/HC1
ARM: dts: exynos: Fix broken reboot on some Odroid U2/X2/U3 boards
Link: https://lore.kernel.org/r/20200316175652.5604-3-krzk@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Minor fixes and additions for 32-bit Tegra SoC device trees.
-----BEGIN PGP SIGNATURE-----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=qQJM
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.7-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/dt
ARM: tegra: Device tree changes for v5.7-rc1
Minor fixes and additions for 32-bit Tegra SoC device trees.
* tag 'tegra-for-5.7-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Update sound node clocks in device tree
ARM: tegra: Add clock-cells property to PMC
ARM: tegra: Remove USB 2-0 port from Jetson TK1 padctl
Link: https://lore.kernel.org/r/20200313165848.2915133-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
