Allow using Switchtec NTB in setups that have more than two partitions.
Note: this does not enable having multi-host communication, it only
allows for a single NTB link between two hosts in a network that might
have more than two.
Use following logic to determine the NT peer partition:
1) If there are 2 partitions, and the target vector is set in
the Switchtec configuration, use the partition specified in target
vector.
2) If there are 2 partitions and target vector is unset
use the only other partition as specified in the NT EP map.
3) If there are more than 2 partitions and target vector is set
use the other partition specified in target vector.
4) If there are more than 2 partitions and target vector is unset,
this is invalid and report an error.
Signed-off-by: Kelvin Cao <kelvin.cao@microsemi.com>
[logang@deltatee.com: commit message fleshed out]
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Trivial fix to spelling mistake in dev_err error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-By: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.
This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference, especially when the string is defined just a few
lines above the usage of it.
Reported-and-reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Gary R Hook <gary.hook@amd.com>
Cc: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This resolves a bug which may incorrectly configure the peer host's
LUT for shared memory window access. The code was using the local
host's first BAR number, rather than the peer hosts's first BAR
number, to determine what peer NT control register to program.
The bug will cause the Switchtec NTB link to work only if both peers
have the same first NTB BAR configured. In all other configurations,
the link will not come up, failing silently.
When both hosts have the same first BAR, the configuration works only
because the first BAR numbers happent to be the same. When the hosts
do not have the same first BAR, then the LUT translation will not be
configured in the correct peer LUT and will not give the peer the
shared memory window access required for the link to operate.
Signed-off-by: Doug Meyer <dmeyer@gigaio.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: 678784a44ae8 ("NTB: switchtec_ntb: Initialize hardware for memory windows")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The workaround code is never used because Skylake NTB does not need it.
Reported-by: Allen Hubbe <allen.hubbe@dell.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Make these const as they are only used during a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The Switchtec hardware has two types of memory windows: LUTs and Direct.
The first area in each BAR is for LUT windows and the remaining area is
for the direct region. The total number of LUT entries is set by a
configuration setting in hardware and they all must be the same
size. (This is fixed by switchtec_ntb to be 64K.)
switchtec_ntb enables the LUTs only for the first BAR and enables the
highest power of two possible. Seeing the LUTs are at the beginning of
the BAR, the direct memory window's alignment is affected. Therefore,
the maximum direct memory window size can not be greater than the number
of LUTs times 64K. The direct window in other BARs will not have this
restriction as the LUTs will not be enabled there. LUTs will only be
exposed through the NTB API if the use_lut_mw parameter is set.
Seeing the Switchtec hardware, by default, configures BARs to be 4G a
module parameter is given to limit the size of the advertised memory
windows. Higher layers tend to allocate the maximum BAR size and this
has a tendency to fail when they try to allocate 4GB of contiguous
memory.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Seeing there is no dedicated hardware for this, we simply add
these as entries in the shared memory window. Thus, we could support
any number of them but 128 seems like enough, for now.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Pretty straightforward implementation of doorbell registers.
The shift and mask were setup in an earlier patch and this just hooks
up the appropriate portion of the IDB register as the local doorbells
and the opposite portion of ODB as the peer doorbells. The DB mask is
protected by a spinlock to avoid concurrent read-modify-write accesses.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
switchtec_ntb checks for a link by looking at the shared memory
window. If the magic number is correct and the other side indicates
their link is enabled then we take the link to be up.
Whenever we change our local link status we send a msg to the
other side to check whether it's up and change their status.
The current status is maintained in a flag so ntb_is_link_up
can return quickly.
We utilize Switchtec's link status notifier to also check link changes
when the switch notices a port changes state.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add a skeleton NTB driver which will be filled out in subsequent patches.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Set up some hardware registers and creates interrupt service routines
for the doorbells and messages.
There are 64 doorbells in the switch that are shared between all
partitions. The upper 4 doorbells are also shared with the messages
and are therefore not used. Thus, this provides 28 doorbells for each
partition.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Add the code to initialize the memory windows in the hardware.
This includes setting up the requester ID table, and figuring out
which BAR corresponds to which memory window. (Seeing the switch
can be configured with any number of BARs.)
Also, seeing the device doesn't have hardware for scratchpads or
determining the link status, we create a shared memory window that has
these features. A magic number with a version component will be used
to determine if the other side's driver is actually up.
The shared memory window also informs the other side of the
size and count of the local memory windows.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Seeing the Switchtec NTB hardware shares the same endpoint as the
management endpoint we utilize the class_interface API to register
an NTB driver for every Switchtec device in the system that has the
NTB class code.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Stephen Bates <sbates@raithlin.com>
Reviewed-by: Kurt Schwemmer <kurt.schwemmer@microsemi.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
With Switchtec hardware it's impossible to get the alignment parameters
for a peer's memory window until the peer's driver has configured its
windows. Strictly speaking, the link doesn't have to be up for this,
but the link being up is the only way the client can tell that
the other side has been configured.
This patch converts ntb_transport and ntb_perf to use this function after
the link goes up. This simplifies these clients slightly because they
no longer have to store the alignment parameters. It also tweaks
ntb_tool so that peer_mw_trans will print zero if it is run before
the link goes up.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
It seems that under certain scenarios the SPAD can have bogus values caused
by an agent (i.e. BIOS or other software) that is not the kernel driver, and
that causes memory window setup failure. This should not cause the link to
be disabled because if we do that, the driver will never recover again. We
have verified in testing that this issue happens and prevents proper link
recovery.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Fixes: 84f766855f ("ntb: stop link work when we do not have memory")
After converting to the new API, both ntb_tool and ntb_transport are
using ntb_mw_count to iterate through ntb_peer_get_addr when they
should be using ntb_peer_mw_count.
This probably isn't an issue with the Intel and AMD drivers but
this will matter for any future driver with asymetric memory window
counts.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Fixes: 443b9a14ec ("NTB: Alter MW API to support multi-ports devices")
If a failure occurs when creating Debug FS entries, unroll all of
the work that's been done.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The ntb_perf tool uses module parameters to control the
characteristics of its test. Enable the changing of these
options through debugfs, and eliminating the need to unload
and reload the module to make changes and run additional tests.
Add a new module parameter that forces the DMA channel
selection onto the same node as the NTB device (default: true).
- seg_order: Size of the NTB memory window; power of 2.
- run_order: Size of the data buffer; power of 2.
- use_dma: Use DMA or memcpy? Default: 0.
- on_node: Only use DMA channel(s) on the NTB node. Default: true.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The Debug FS entries manage themselves; we don't need to hang onto
them in the context structure.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The DMA channel(s)/memory used to transfer data to an NTB device
may not be required to be on the same node as the device. Add a
module parameter that allows any candidate channel (aside from
node assocation) and allocated memory to be used.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
IDT 89HPESxNTx device series is PCIe-switches, which support
Non-Transparent bridging between domains connected to the device ports.
Since new NTB API exposes multi-port interface and messaging API, the
IDT NT-functions can be now supported in the kernel. This driver adds
the following functionality:
1) Multi-port NTB API to have information of possible NT-functions
activated in compliance with available device ports.
2) Memory windows of direct and look up table based address translation
with all possible combinations of BARs setup.
3) Traditional doorbell NTB API.
4) One-on-one messaging NTB API.
There are some IDT PCIe-switch setups, which must be done before any of
the NTB peers started. It can be performed either by system BIOS via
IDT SMBus-slave interface or by pre-initialized IDT PCIe-switch EEPROM:
1) NT-functions of corresponding ports must be activated using
SWPARTxCTL and SWPORTxCTL registers.
2) BAR0 must be configured to expose NT-function configuration
registers map.
3) The rest of the BARs must have at least one memory window
configured, otherwise the driver will just return an error.
Temperature sensor of IDT PCIe-switches can be also optionally
activated by BIOS or EEPROM.
(See IDT documentations for details of how the pre-initialization can
be done)
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
As per a comments in [1] by Greg Kroah-Hartman, the ndev_* macros should
be cleaned up. This makes it more clear what's actually going on when
reading the code.
[1] http://www.spinics.net/lists/linux-pci/msg56904.html
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
As per a comments in [1] by Greg Kroah-Hartman, the ndev_* macros should
be cleaned up. This makes it more clear what's actually going on when
reading the code.
[1] http://www.spinics.net/lists/linux-pci/msg56904.html
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Some IDT NTB-capable PCIe-switches have message registers to communicate with
peer devices. This patch adds new NTB API callback methods, which can be used
to utilize these registers functionality:
ntb_msg_count(); - get number of message registers
ntb_msg_inbits(); - get bitfield of inbound message registers status
ntb_msg_outbits(); - get bitfield of outbound message registers status
ntb_msg_read_sts(); - read the inbound and outbound message registers status
ntb_msg_clear_sts(); - clear status bits of message registers
ntb_msg_set_mask(); - mask interrupts raised by status bits of message
registers.
ntb_msg_clear_mask(); - clear interrupts mask bits of message registers
ntb_msg_read(midx, *pidx); - read message register with specified index,
additionally getting peer port index which data received from
ntb_msg_write(midx, pidx); - write data to the specified message register
sending it to the passed peer device connected over a pidx port
ntb_msg_event(); - notify driver context of a new message event
Of course there is hardware which doesn't support Message registers, so
this API is made optional.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Even though there is no any real NTB hardware, which would have both more
than two ports and Scratchpad registers, it is logically correct to have
Scratchpad API accepting a peer port index as well. Intel/AMD drivers utilize
Primary and Secondary topology to split Scratchpad between connected root
devices. Since port-index API introduced, Intel/AMD NTB hardware drivers can
use device port to determine which Scratchpad registers actually belong to
local and peer devices. The same approach can be used if some potential
hardware in future will be multi-port and have some set of Scratchpads.
Here are the brief of changes in the API:
ntb_spad_count() - return number of Scratchpads per each port
ntb_peer_spad_addr(pidx, sidx) - address of Scratchpad register of the
peer device with pidx-index
ntb_peer_spad_read(pidx, sidx) - read specified Scratchpad register of the
peer with pidx-index
ntb_peer_spad_write(pidx, sidx) - write data to Scratchpad register of the
peer with pidx-index
Since there is hardware which doesn't support Scratchpad registers, the
corresponding API methods are now made optional.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Multi-port NTB devices permit to share a memory between all accessible peers.
Memory Windows API is altered to correspondingly initialize and map memory
windows for such devices:
ntb_mw_count(pidx); - number of inbound memory windows, which can be allocated
for shared buffer with specified peer device.
ntb_mw_get_align(pidx, widx); - get alignment and size restriction parameters
to properly allocate inbound memory region.
ntb_peer_mw_count(); - get number of outbound memory windows.
ntb_peer_mw_get_addr(widx); - get mapping address of an outbound memory window
If hardware supports inbound translation configured on the local ntb port:
ntb_mw_set_trans(pidx, widx); - set translation address of allocated inbound
memory window so a peer device could access it.
ntb_mw_clear_trans(pidx, widx); - clear the translation address of an inbound
memory window.
If hardware supports outbound translation configured on the peer ntb port:
ntb_peer_mw_set_trans(pidx, widx); - set translation address of a memory
window retrieved from a peer device
ntb_peer_mw_clear_trans(pidx, widx); - clear the translation address of an
outbound memory window
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Multi-port devices permit the NTB connections between multiple domains,
so a local device can have NTB link being up with one peer and being
down with another. NTB link-state API is appropriately altered to return
a bitfield of the link-states between the local device and possible peers.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
There is some NTB hardware, which can combine more than just two domains
over NTB. For instance, some IDT PCIe-switches can have NTB-functions
activated on more than two-ports. The different domains are distinguished
by ports they are connected to. So the new port-related methods are added to
the NTB API:
ntb_port_number() - return local port
ntb_peer_port_count() - return number of peers local port can connect to
ntb_peer_port_number(pdix) - return port number by it index
ntb_peer_port_idx(port) - return port index by it number
Current test-drivers aren't changed much. They still support two-ports devices
for the time being while multi-ports hardware drivers aren't added.
By default port-related API is declared for two-ports hardware.
So corresponding hardware drivers won't need to implement it.
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Do not sleep in ntb_async_tx_submit, which could deadlock.
This reverts commit "8c874cc140d667f84ae4642bb5b5e0d6396d2ca4"
Fixes: 8c874cc140 ("NTB: Address out of DMA descriptor issue with NTB")
Reported-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Allen Hubbe <Allen.Hubbe@dell.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Fixing doorbell register length to 32bits per spec. On Skylake NTB, the
doorbell registers are 32bit write only registers. The source for the
doorbell is a 64bit register that shows the interrupt bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6cc4 ("ntb: Adding Skylake Xeon NTB support")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
A divide by zero error occurs if qp_count is less than mw_count because
num_qps_mw is calculated to be zero. The calculation appears to be
incorrect.
The requirement is for num_qps_mw to be set to qp_count / mw_count
with any remainder divided among the earlier mws.
For example, if mw_count is 5 and qp_count is 12 then mws 0 and 1
will have 3 qps per window and mws 2 through 4 will have 2 qps per window.
Thus, when mw_num < qp_count % mw_count, num_qps_mw is 1 higher
than when mw_num >= qp_count.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In cases where there are more mw's than spads/2-2, the mw count gets
reduced to match the limitation. ntb_transport also tries to ensure that
there are fewer qps than mws but uses the full mw count instead of
the reduced one. When this happens, the math in
'ntb_transport_setup_qp_mw' will get confused and result in a kernel
paging request bug.
This patch fixes the bug by reducing qp_count to the reduced mw count
instead of the full mw count.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The order parameters are powers of 2; adjust the usage information
to use correct mathematical representations.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Fixes: 8a7b6a778a ("ntb: ntb perf tool")
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On Skylake hardware, the link_poll isn't clearing the pending interrupt
bit. Adding a new function for SKX that handles clearing of status bit the
right way.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 783dfa6c ("ntb: Adding Skylake Xeon NTB support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Fix typo causing ntb_transport_create_queue to select the first
queue every time, instead of using the next free queue.
Signed-off-by: Thomas VanSelus <tvanselus@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: fce8a7bb5 ("PCI-Express Non-Transparent Bridge Support")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In the normal I/O execution path, ntb_perf is missing a call to
dmaengine_unmap_put() after submission. That causes us to leak
unmap objects.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 8a7b6a77 ("ntb: ntb perf tool")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The call to debugfs_remove_recursive(qp->debugfs_dir) of the sub-level
directory must not be later than
debugfs_remove_recursive(nt_debugfs_dir) of the top-level directory.
Otherwise, the sub-level directory will not exist, and it would be
invalid (panic) to attempt to remove it. This removes the top-level
directory last, after sub-level directories have been cleaned up.
Signed-off-by: Allen Hubbe <Allen.Hubbe@dell.com>
Fixes: e26a5843f ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The results were previously ignored, anyway.
Signed-off-by: Steve Wahl <Steve.Wahl@dell.com>
Fixes: e26a5843f7
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
'request_irq()' and 'free_irq()' should have the same 'dev_id'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The offsets for the SZ registers are wrong. Updated.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Sandeep Mann <sandeep@purestorage.com>
Tested-by: Zachary Ross <zacharyx.ross@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When the underlying NTB H/W driver advertises more memory windows
than the number of scratchpads available to setup MW's, it is likely
that we may end up filling the remaining memory windows with garbage.
So to avoid that, lets limit the memory windows that transport driver
can setup based on the available scratchpads.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Due to incorrect limit and translation register values, NTB link was
going down when the memory window was setup. Made appropriate changes
as per spec.
Fix limit register values for BAR1, which was overlapping
with the BAR23 address.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
AMD NTB support hotplug under B2B mode. NTB will trigger link
up/down interrupt event when doing plug add/remove, this patch
implements the two interrupt event to support B2B hotplug function.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The Skylake Xeon NTB hardware has made some changes to the register name,
offset, and the way doorbells work. Adding driver support for the new
hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This is a static checker warning, not something I'm desperately
concerned about. But snprintf() returns the number of bytes that
would have been copied if there were space. We really care about the
number of bytes that actually were copied so we should use scnprintf()
instead.
It probably won't overrun, and in that case we may as well just use
sprintf() but these sorts of things make static checkers and code
reviewers happier.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The peer_addr member of intel_ntb_dev is not set, therefore when
acquiring ntb_peer_db and ntb_peer_spad we only get the offset rather
than the actual physical address. Adding fix to correct that.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
schedule_timeout_* takes a timeout in jiffies but the code currently is
passing in a constant which makes this timeout HZ dependent, so pass it
through msecs_to_jiffies() to fix this up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
schedule_timeout_* takes a timeout in jiffies but the code currently is
passing in a constant which makes this timeout HZ dependent, so pass it
through msecs_to_jiffies() to fix this up.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Adding support on the rx DMA path to allow recovery of errors when
DMA responds with error status and abort all the subsequent ops.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: linux-ntb@googlegroups.com
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Adding support on the tx DMA path to allow recovery of errors when
DMA responds with error status and abort all the subsequent ops.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: linux-ntb@googlegroups.com
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Clean up duplicated expression by replacing it with the equivalent local
variable pdev.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
It will be useful to know the hardware configured BAR size to diagnose
issues with NTB memory windows.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When the link goes down, the link_is_up flag did not return to
false. This could have caused some subtle corner case bugs
when the link goes up and down quickly.
Once that was fixed, there was found to be a race if the link was
brought down then immediately up. The link_cleanup work would
occasionally be scheduled after the next link up event. This would
cancel the link_work that was supposed to occur and leave ntb_perf
in an unusable state.
To fix this we get rid of the link_cleanup work and put the actions
directly in the link_down event.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This commit adds a debugfs 'count' file to ntb_pingpong. This is so
testing with ntb_pingpong can be automated beyond just checking the
logs for pong messages.
The count file returns a number which increments every pong. The
counter can be cleared by writing a zero.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In order to more successfully script with ntb_tool it's useful to
have a link file to check the link status so that the script
doesn't use the other files until the link is up.
This commit adds a 'link' file to the debugfs directory which reads
boolean (Y or N) depending on the link status. Writing to the file
change the link state using ntb_link_enable or ntb_link_disable.
A 'link_event' file is also provided so an application can block until
the link changes to the desired state. If the user writes a 1, it will
block until the link is up. If the user writes a 0, it will block until
the link is down.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
In order to make the interface closer to the raw NTB API, this commit
changes memory windows so they are not initialized on link up.
Instead, the 'peer_trans*' debugfs files are introduced. When read,
they return information provided by ntb_mw_get_range. When written,
they create a buffer and initialize the memory window. The
value written is taken as the requested size of the buffer (which
is then rounded for alignment). Writing a value of zero frees the buffer
and tears down the memory window translation. The 'peer_mw*' file is
only created once the memory window translation is setup by the user.
Additionally, it was noticed that the read and write functions for the
'peer_mw*' files should have checked for a NULL pointer.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of returning immediately with an error when the link is
down, wait for the link to come up (or the user sends a SIGINT).
This is to make scripting ntb_perf easier.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of having to watch logs, allow the results to be retrieved
by reading back the run file. This file will return "running" when
the test is running and nothing if no tests have been run yet.
It returns 1 line per thread, and will display an error message if the
corresponding thread returns an error.
With the above change, the pr_info calls that returned the results are
then changed to pr_debug calls.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This commit accomplishes a few things:
1) Properly prevent multiple sets of threads from running at once using
a mutex. Lots of race issues existed with the thread_cleanup.
2) The mutex allows us to ensure that threads are finished before
tearing down the device or module.
3) Don't use kthread_stop when the threads can exit by themselves, as
this is counter-indicated by the kthread_create documentation. Threads
now wait for kthread_stop to occur.
4) Writing to the run file now blocks until the threads are complete.
The test can then be safely interrupted by a SIGINT.
Also, while I was at it:
5) debugfs_run_write shouldn't return 0 in the early check cases as this
could cause debugfs_run_write to loop undesirably.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
When debugging performance problems, if some issue causes the ntb
hardware to be significantly slower than expected, ntb_perf will
hang requiring a reboot because it only schedules once every 4GB.
Instead, schedule based on jiffies so it will not hang the CPU if
the transfer is slow.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
I'm working on hardware that currently has a limited number of
scratchpad registers and ntb_ndev fails with no clue as to why. I
feel it is better to fail early and provide a reasonable error message
then to fail later on.
The same is done to ntb_perf, but it doesn't currently require enough
spads to actually fail. I've also removed the unused SPAD_MSG and
SPAD_ACK enums so that MAX_SPAD accurately reflects the number of
spads used.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
We allocate some memory window buffers when the link comes up, then we
provide debugfs files to read/write each side of the link.
This is useful for debugging the mapping when writing new drivers.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On my system, dma_alloc_coherent won't produce memory anywhere
near the size of the BAR. So I needed a way to limit this.
It's pretty much copied straight from ntb_transport.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Currently we only allocate a fixed default number of descriptors for the tx
and rx side. We should dynamically resize it to the number of descriptors
resides in the transport rings. We should know the number of transmit
descriptors at initializaiton. We will allocate the default number of
descriptors for receive side and allocate additional ones when we know the
actual max entries for receive.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <allen.hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
On hardware with 32 scratchpad registers the spad field in ntb tool
could chop off the end. The maximum buffer size is increased from
256 to 15 times the number or scratchpads.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
If you tried to write two spads in one line, as per the example:
root@peer# echo '0 0x01010101 1 0x7f7f7f7f' > $DBG_DIR/peer_spad
then the CPU would freeze in an infinite loop.
This wasn't immediately obvious but 'pos' was not incrementing the
buffer, so after reading the second pair of values, 'pos' would once
again be 3 and it would re-read the second pair of values ad infinitum.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Kernel zero day testing warned about address space confusion. A virtual
iomem address was used where a physical address is expected. The
offending functions implement an optional part of the api, so they are
removed. They can be added later, after testing.
Fixes: a1b3695820
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The clean up routine when we failed to allocate kthread is not cleaning
up all the threads, only the same one over and over again.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
kthread_create_no_node() returns error pointers, never NULL. Fix check so
it handles error correctly.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
kmalloc can fail and we should check for NULL before using the pointer
returned by kmalloc.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The perf tool is missing the setup of translation window. Adding call to
setup the translation window for backed memory.
Signed-off-by: John Kading <john.kading@gd-ms.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Instead of keep trying to go through the init routine when we aren't able
to allocate memory, we should just stop and go down.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
We can leave tasklet spinning forever if we disable the tasklet during
qp shutdown and the tasklets are still being kicked off. This hopefully
should avoid that race condition.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reported-by: Alex Depoutovitch <alex@pernixdata.com>
Tested-by: Alex Depoutovitch <alex@pernixdata.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The ntb driver assigns between pointers an __iomem tokens, and
also casts them to 64-bit integers, which results in compiler
warnings on 32-bit systems:
drivers/ntb/test/ntb_perf.c: In function 'perf_copy':
drivers/ntb/test/ntb_perf.c:213:10: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
vbase = (u64)(u64 *)mw->vbase;
^
drivers/ntb/test/ntb_perf.c:214:14: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
dst_vaddr = (u64)(u64 *)dst;
^
This adds __iomem annotations where needed and changes the temporary
variables to iomem pointers to avoid casting them to u64. I did not
see the problem in linux-next earlier, but it show showed up in
4.5-rc1.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Fixes: 8a7b6a778a ("ntb: ntb perf tool")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
If the parameter given to the macro is replaced throughout the macro as
it is evaluated. The intent is that the macro parameter should replace
the only the first parameter to container_of(). However, the way the
macro was written, it would also inadvertantly replace a structure field
name. If a parameter of any other name is given to the macro, it will
fail to compile, if the structure does not contain a field of the same
name. At worst, it will compile, and hide improper access of an
unintended field in the structure.
Change the macro parameter name, so it does not conflict with the
structure field name.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Acked-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
This adds support for AMD's PCI-Express Non-Transparent Bridge
(NTB) device on the Zeppelin platform. The driver connnects to the
standard NTB sub-system interface, with modification to add hooks
for power management in a separate patch. The AMD NTB device has 3
memory windows, 16 doorbell, 16 scratch-pad registers, and supports
up to 16 PCIe lanes running a Gen3 speeds.
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Reviewed-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Providing raw performance data via a tool that directly access data from
NTB w/o any software overhead. This allows measurement of the hardware
performance limit. In revision one we are only doing single direction
CPU and DMA writes. Eventually we will provide bi-directional writes.
The measurement using DMA engine for NTB performance measure does
not measure the raw performance of DMA engine over NTB due to software
overhead. But it should provide the peak performance through the Linux DMA
driver.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Tested-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The transport right now does not handle the case where we run out of DMA
descriptors. We just fail when we do not succeed. Adding code to retry for
a bit attempting to use the DMA engine instead of instantly fail to CPU
copy.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The lower bits read from a BAR register will contain property bits
that we do not care about. Clear those so that we can use the BAR
values for limit and xlat registers.
Reported-by: Conrad Meyer <cem@freebsd.org>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The transmit overrun avoidance error path in ntb_process_tx accidentally
swapped the first two values being passed to the tx_handler client.
This could result in crashes in the ntb_netdev (or other out-of-tree NTB
clients).
Reported-by: Alex Depoutovitch <alex@pernixdata.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
resource_size_t may be 32-bit wide on some architectures, which causes
this warning when building the NTB code:
drivers/ntb/ntb_transport.c: In function 'ntb_transport_link_work':
drivers/ntb/ntb_transport.c:828:46: warning: right shift count >= width of type [-Wshift-count-overflow]
The warning is harmless but can be avoided by using the upper_32_bits()
macro.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e26a5843f7 ("NTB: Split ntb_hw_intel and ntb_transport drivers")
Signed-off-by: Jon Mason <jdmason@kudzu.us>
There is no need for the upstream and downstream addresses to be different
for the NTB configs. Go to using a single set of address. It is still
possible to configure them differently using module parameter override
however.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked and Tested-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Order of operations issue with the QP Num and MW count, which would
result in the receive buffer pointer being invalid if there are more
than 1 MW. Corrected with parenthesis to enforce the proper order of
operations.
Reported-by: John I. Kading <John.Kading@gd-ms.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
These variables were not used anywhere. So remove them.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
We were accessing nt->mw_vec after freeing it. Fix the error path so
that we free nt->mw_vec after we have finished using it.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
smatch detected an issue in the function ntb_transport_max_size() where
we could be dereferencing a dma channel pointer when it is NULL.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Check that b2b_mw_idx is in range of the number of memory windows when
initializing the device. The workaround is considered to be in effect
only if the device b2b_idx is exactly UINT_MAX, instead of any index
past the last memory window.
Only print B2B MW workaround information in debugfs if the workaround is
in effect.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Allocate two DMA channels, one for TX operation and one for RX
operation, instead of having one DMA channel for everything. This
provides slightly better performance, and also will make error handling
cleaner later on.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The dma_sync_wait can hurt the performance of workloads mixed with both
large and small frames. Large frames will be copied using the dma
engine. Small frames will be copied by the cpu. The dma_sync_wait
prevents the cpu and dma engine copying in parallel.
In the period where the cpu is copying, the dma engine is stopped. The
dma engine is not doing any useful work to copy large frames during that
time, and the additional time to restart the dma engine for the next
large frame. This will decrease the throughput for the portion of a
workload with large frames.
In the period where the dma engine is copying, the cpu is held up
waiting for dma to complete. The small frames processing will be
delayed until the dma is complete. The RX frames are completed
in-order, and the processing of small frames takes very little time, so
dma_sync_wait may have an insignificant impact on the respose time of
frames. The more significant impact is to the system, because the delay
in dma_sync_wait is implemented as busy non-blocking wait. This can
prevent the delayed core from doing any useful work, even if it could be
processing work for other drivers, unrelated to transport RX processing.
After applying the earlier patch to fix out-of-order RX acknoledgement,
the dma_sync_wait is no longer necessary. Remove it, so that cpu memcpy
will proceed immediately for small frames, in parallel with ongoing dma
for large frames. Do not hold up the cpu from doing work while dma is
in progress. The prior fix will continue to ensure in-order completion
of the RX frames to the upper layer, and in-order delivery of the RX
acknoledgement.
Signed-off-by: Allen Hubbe <Allen.Hubbe@emc.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Make QP stats info more readable for debugging purposes. Also add an
entry to indicate whether DMA is being used.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
The list should be added from the bottom and not the top in order to
ensure the transport is provided in the same order to clients as ntb
devices are discovered.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Adding PCI Device IDs for B2B (back to back), RP (root port, primary),
and TB (transparent bridge, secondary) devices.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Right now if we push the NTB really hard, we start dropping packets due
to not able to process the packets fast enough. We need to st:qop the
upper layer from flooding us when that happens.
A timer is necessary in order to restart the queue once the resource has
been processed on the receive side. Due to the way NTB is setup, the
resources on the tx side are tied to the processing of the rx side and
there's no async way to know when the rx side has released those
resources.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
