The ELD notification can be received asynchronously from the graphics
side, and this may happen just at the moment the sound driver is
processing the suspend or the resume, and it would confuse the whole
procedure. Since the ELD and connection states are updated in anyway
at the end of the resume, we can skip it when received during PM
process.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I've tested it on one device and it works fine, no clicks.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The numbers aren't always linear, just like in the real world.
Correct to the right numbers stated in the datasheet (although we
can't trust the datasheet as well).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent addition of ELD notifier for Intel HDMI/DP codec may lead
the bad codec connection found as kernel messages like below:
Suspending console(s) (use no_console_suspend to debug)
hdmi_present_sense: snd_hda_codec_hdmi hdaudioC0D2: HDMI status: Codec=2 Pin=6 Presence_Detect=1 ELD_Valid=1
snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f2e08
snd_hda_intel 0000:00:1f.3: spurious response 0x0:0x2, last cmd=0x206f2e08
....
snd_hda_codec_hdmi hdaudioC0D2: HDMI: ELD buf size is 0, force 128
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: last cmd=0x206f2f00
snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x206f2f00
snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to single_cmd mode: last cmd=0x206f2f00
azx_single_wait_for_response: 42 callbacks suppressed
This seems appearing when the sound driver went to suspend before i915
driver. Then i915 driver disables HDMI/DP audio bit and calls the
registered notifier, and the HDA codec tries to handle it as a
hot(un)plug. But since the driver is already in the suspended state,
it fails miserably.
As this is a sort of spurious wakeup, it can be ignored safely, as
long as it's delivered during the system suspend. OTOH, if a
notification comes during the runtime suspend, the situation is
different: we need to wake up. But during the system suspend, such a
notification can't be the reason for a wakeup.
This patch addresses it by a simple check of the current sound card
status. The skipped notification doesn't matter because the HDA
driver will check the plugged status forcibly at the resume in
return.
Then, why the card status, not a runtime PM status or else? The HDA
controller driver is supposed to set the card status to D3 at the
system suspend but not at the runtime suspend. So we can see it as a
flag that is set only for the system suspend. Admittedly, it's a bit
ugly, but it should work well for now.
Reported-and-tested-by: "Zhang, Xiong Y" <xiong.y.zhang@intel.com>
Fixes: 25adc137c5 ('ALSA: hda - Wake the codec up on pin/ELD notify events')
Cc: <stable@vger.kernel.org> # v4.3+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Quite a large batch of fixes have come in since the merge window, mainly
driver specific ones but there's a couple of core ones:
- A fix for DAPM resume on active streams to ensure everything ends up
cleanly in the right state.
- Reset the DAPM cache when freeing widgets to fix a crash on driver
remove and reload.
The PM functions for nau8825 are new code which fix crashes on resume.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWWE13AAoJECTWi3JdVIfQF+wH/3D0Asc5rVdU81cxaxdjgGxJ
WUGUCJ+4D1HTtZQf8MouwFqMvDK+lOKiPkAzMdyk3NQG50S0XtMD8xM7JeglPZ1L
U7ro6EfYqGmkMyqClVxWnJMBnGoTiLrAftFlIBFPaQ6FDdfMMlNcK2Y4hCs/t3y7
A5T0LlqKdz++bKQRoq0zpiWWSnfoaEub25IaEB97k9sjlr9rRTR1UwHibHdm3JGg
vzkqLTaH/zm1VgR70jH6XnQSN8KtIdrx/u2ZWJZVqfioMTMFYIboufcwDWqX4oNA
vqcYjzfCyhDaMnVYpI+7ettHfXn3iBR3VykXIOI1uzM63N5f1IK7bOwPRxiMXAA=
=CDO8
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.4-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.4
Quite a large batch of fixes have come in since the merge window, mainly
driver specific ones but there's a couple of core ones:
- A fix for DAPM resume on active streams to ensure everything ends up
cleanly in the right state.
- Reset the DAPM cache when freeing widgets to fix a crash on driver
remove and reload.
The PM functions for nau8825 are new code which fix crashes on resume.
Gigabyte Z710X mobo with ALC1150 codec gets significant noises from
the analog loopback routes even if their inputs are all muted.
Simply kill the aamix for fixing it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=108301
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have a machine Dell XPS 13 with the codec alc256, after resume back
from S3, the headphone has noise when play sound.
Through comparing with the coeff vaule before and after S3, we found
restoring a coeff register will help remove noise.
BugLink: https://bugs.launchpad.net/bugs/1519168
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turned out that many HP laptops suffer from the same problem as
fixed in commit [c932b98c1e: ALSA: hda - Apply pin fixup for HP
ProBook 6550b]. But, it's tiresome to list up all such PCI SSIDs, as
there are really lots of HP machines.
Instead, we do a bit more clever, try to check the supposedly dock and
built-in headphone pins, and apply the fixup when both seem valid.
This rule can be applied generically to all models using the same
quirk, so we'll fix all in a shot.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=107491
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For making the speakers on Acer Aspire One Cloudbook 14 to work, we
need the as same quirk as for another Chromebook. This patch adds the
corresponding fixup entry.
Reported-by: Patrick <epictetus@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For SKL, only the HDMI codec is in the display power well while the
HD-A controller isn't. So the codec flag 'link_power_control' is
set to request/release the display power via bus link_power ops.
For BXT, the power well design is the same as SKL, so the patch
should be applied to BXT too.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add HD Audio Device PCI ID for the Intel Broxton platform.
It is an HDA Intel PCH controller.
Signed-off-by: Lu, Han <han.lu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here are a collection of small fixes tha have been gathered for
4.4-rc1. The only significant changes are those in PCI drivers
Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
A reverse select is often more user-friendly, but in this case, it
makes hard to manage with the conflict with ZONE_DEVICE, so changed in
such a way for now.
Others are all small fixes and quirks: an error check in soundcore
reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
quirk, USB-audio DSD device quirk, some constifications, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJWRw2MAAoJEGwxgFQ9KSmkoMIQAK0ORPYWNqHpELyu3e2ohaxD
VJxRTOw1ZHTMEDm2N9gYp93PxKlH/ja8XDltV0FXttcCMzj98V8z2gXxhGFF9lUw
MKnUnDahvC9oIRQscQZUggUKkNHuTJ/vcWPzVQqUZJNVIvFog52ikKnxfUJau6b4
ONkWJo2JVXdVi6Q+fCvCvzejeHukMTRPcAahBLP13geNtbO3Va6XfsfqRecHDm4T
MKV6HApacYovKmRDbdA3eTpY8Rf+7VjcvIleJ9bbwPBdxb4J/ZNzZLKRq9A4yXDp
A5ScIsmd0doht688zagDTizCcPXmRIzdmY0JbnwryxXkBm8K4u285UteMbTJgFPP
1r14o8BU3cWYc/fYySacSSArS0zYVPqxJxlEXY/Nl4O9gCKiOjFxffTPBMhErYcT
XlJbBxuUQn58Oms1SqpXOJOwKMI6zEWg58ksFcm9+7Z8iiyoVpJY1ZhiOEG72fJg
LydPyryjlEo2CUm1pzKL+kX8XZt/H8i28kqGrI54saVu//YM26PLSzoAHhXj2QDV
B0ENG4o36Uuo0TWbLu4TqNXZV99c2kG1TN+yOHOEyjtcnnskJM+QbnmlKBZO5PZB
s/XqEni41GWaYLZo7OHfGukPyavjLV4b64aejHPQ6yhB8EUZxD1ZhIlA9+wqFoz/
kEm5aeJZHTaGfFI7TQVG
=k0zD
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes tha have been gathered for
4.4-rc1. The only significant changes are those in PCI drivers
Kconfig, to use "depends on" instead of "select" for CONFIG_ZONE_DMA.
A reverse select is often more user-friendly, but in this case, it
makes hard to manage with the conflict with ZONE_DEVICE, so changed in
such a way for now.
Others are all small fixes and quirks: an error check in soundcore
reigster_chrdev(), HD-audio HDMI/DP phantom jack fix, Intel Broxton DP
quirk, USB-audio DSD device quirk, some constifications, etc"
* tag 'sound-fix-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: pci: depend on ZONE_DMA
ALSA: hda - Simplify phantom jack handling for HDMI/DP
ALSA: hda/hdmi - apply Skylake fix-ups to Broxton display codec
ALSA: ctxfi: constify rsc ops structures
ALSA: usb: Add native DSD support for Aune X1S
ALSA: oxfw: add an comment to Kconfig for TASCAM FireOne
sound: fix check for error condition of register_chrdev()
Dell Latitude E6440 (1028:05bd) needs the same fixup as applied to
other Latitude E7xxx models for the click noise due to the recent
power-saving changes.
Bugzilla: http://bugzilla.opensuse.org/show_bug.cgi?id=954876
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HDMI codec parser may create a phantom jack, but the helper
function snd_hda_jack_add_kctl() treats always as a normal jack. This
is superfluous as the jack query is executed at each time the jack
sync is performed.
Since the HDMI codec parser is the only caller of this function, it's
easier to change back this directly calling the original
__snd_hda_jack_add_kctl() with phantom_jack parameter.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Broxton and Skylake have the same behavior on display audio. So this patch
applys Skylake fix-ups to Broxton.
Signed-off-by: Lu, Han <han.lu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull drm updates from Dave Airlie:
"I Was Almost Tempted To Capitalise Every Word, but then I decided I
couldn't read it myself!
I've also got one pull request for the sti driver outstanding. It
relied on a commit in Greg's tree and I didn't find out in time, that
commit is in your tree now so I might send that along once this is
merged.
I also had the accidental misfortune to have access to a Skylake on my
desk for a few days, and I've had to encourage Intel to try harder,
which seems to be happening now.
Here is the main drm-next pull request for 4.4.
Highlights:
New driver:
vc4 driver for the Rasberry Pi VPU.
(From Eric Anholt at Broadcom.)
Core:
Atomic fbdev support
Atomic helpers for runtime pm
dp/aux i2c STATUS_UPDATE handling
struct_mutex usage cleanups.
Generic of probing support.
Documentation:
Kerneldoc for VGA switcheroo code.
Rename to gpu instead of drm to reflect scope.
i915:
Skylake GuC firmware fixes
HPD A support
VBT backlight fallbacks
Fastboot by default for some systems
FBC work
BXT/SKL workarounds
Skylake deeper sleep state fixes
amdgpu:
Enable GPU scheduler by default
New atombios opcodes
GPUVM debugging options
Stoney support.
Fencing cleanups.
radeon:
More efficient CS checking
nouveau:
gk20a instance memory handling improvements.
Improved PGOB detection and GK107 support
Kepler GDDR5 PLL statbility improvement
G8x/GT2xx reclock improvements
new userspace API compatiblity fixes.
virtio-gpu:
Add 3D support - qemu 2.5 has it merged for it's gtk backend.
msm:
Initial msm88896 (snapdragon 8200)
exynos:
HDMI cleanups
Enable mixer driver byt default
Add DECON-TV support
vmwgfx:
Move to using memremap + fixes.
rcar-du:
Add support for R8A7793/4 DU
armada:
Remove support for non-component mode
Improved plane handling
Power savings while in DPMS off.
tda998x:
Remove unused slave encoder support
Use more HDMI helpers
Fix EDID read handling
dwhdmi:
Interlace video mode support for ipu-v3/dw_hdmi
Hotplug state fixes
Audio driver integration
imx:
More color formats support.
tegra:
Minor fixes/improvements"
[ Merge fixup: remove unused variable 'dev' that had all uses removed in
commit 4e270f0880: "drm/gem: Drop struct_mutex requirement from
drm_gem_mmap_obj" ]
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (764 commits)
drm/vmwgfx: Relax irq locking somewhat
drm/vmwgfx: Properly flush cursor updates and page-flips
drm/i915/skl: disable display side power well support for now
drm/i915: Extend DSL readout fix to BDW and SKL.
drm/i915: Do graphics device reset under forcewake
drm/i915: Skip fence installation for objects with rotated views (v4)
vga_switcheroo: Drop client power state VGA_SWITCHEROO_INIT
drm/amdgpu: group together common fence implementation
drm/amdgpu: remove AMDGPU_FENCE_OWNER_MOVE
drm/amdgpu: remove now unused fence functions
drm/amdgpu: fix fence fallback check
drm/amdgpu: fix stoping the scheduler timeout
drm/amdgpu: cleanup on error in amdgpu_cs_ioctl()
drm/i915: Fix locking around GuC firmware load
drm/amdgpu: update Fiji's Golden setting
drm/amdgpu: update Fiji's rev id
drm/amdgpu: extract common code in vi_common_early_init
drm/amd/scheduler: don't oops on failure to load
drm/amdgpu: don't oops on failure to load (v2)
drm/amdgpu: don't VT switch on suspend
...
Adding Intel codename Lewisburg platform device IDs for audio.
[rearranged the position by tiwai]
Signed-off-by: Alexandra Yates <alexandra.yates@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP ProBook 6550b needs the same pin fixup applied to other HP B-series
laptops with docks for making its headphone and dock headphone jacks
working properly. We just need to add the codec SSID to the list.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=191971
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During the migration to HDA core code, we lost the workaround for 4k
BDL boundary. The flag exists in the new hdac_bus, but it's never
set. This resulted in the sudden sound stall on some controllers that
require this workaround like Creative Recon3D.
This patch fixes the issue by setting the flag for such controllers
properly.
Fixes: ccc98865aa ('ALSA: hda - Migrate more hdac_stream codes')
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've had many reports that some Creative sound cards with CA0132
don't work well. Some reported that it starts working after reloading
the module, while some reported it starts working when a 32bit kernel
is used. All these facts seem implying that the chip fails to
communicate when the buffer is located in 64bit address.
This patch addresses these issues by just adding AZX_DCAPS_NO_64BIT
flag to the corresponding PCI entries. I casually had a chance to
test an SB Recon3D board, and indeed this seems helping.
Although this hasn't been tested on all Creative devices, it's safer
to assume that this restriction applies to the rest of them, too. So
the flag is applied to all Creative entries.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This machine had I2S codec for speaker output.
It need to refill the I2S codec initial verb after resume back.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Reported-and-tested-by: George Gugulea <gugulea@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use codec_*() macro instead of pr_*() for improving the log
information. The current form even slips from alsa-info.sh.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWLbbGAAoJECTWi3JdVIfQH7oH/1VdN2ozP9A03p24aC5qso1F
VWOBnG4pkw1G6J5qK2lemMDeJdRdTfreICUAa9Tw9kOSfTIb6F3X8kCw8tbwlw0I
4phgmyo23P53OfLZFMkQi/RCfwItnE0sszqhvoumUg0ryjYxg2JT+gTMgwvVo7Pq
hf6m6a3we5pxLIIYP4wlQgOKwUJe4B4nC37ExySf24Dlo/DzmWDtfQbGvmyluFzb
MB1qzEvAc/KC3LZFkIFmhfg2/caNRhcQrzkUCYrLR3t+oz9P1zCpYTII7VDdMg7L
SM2VoL+ynEAdBqa38Ozwxvd/mpHwinlAeiikuwz1PyxVOqZvZqqiWzD8eUJkhZk=
=/F/Q
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.3-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.4
Not much core work here, a few small tweaks to interfaces but mainly the
changes here are driver ones. Highlights include:
- Updates to the topology userspace interface
- Big updates to the Renesas support from Morimoto-san
- Most of the support for Intel Sky Lake systems.
- New drivers for Asahi Kasei Microdevices AK4613, Allwinnner A10,
Cirrus Logic WM8998, Dialog DA7219, Nuvoton NAU8825 and Rockchip
S/PDIF.
- A new driver for the Atmel Class D speaker drivers
The HDA codec driver issues snd_hda_codec_reset() at the error path of
PCM build. This was needed in the earlier code base, but the recent
rewrite to use the standard bus binding made this a deadlock:
modprobe D 0000000000000005 0 720 716 0x00000080
Call Trace:
[<ffffffff816a5dbe>] schedule+0x3e/0x90
[<ffffffff816a61a5>] schedule_preempt_disabled+0x15/0x20
[<ffffffff816a7ae5>] __mutex_lock_slowpath+0xb5/0x120
[<ffffffff816a7b6b>] mutex_lock+0x1b/0x30
[<ffffffff8148656b>] device_release_driver+0x1b/0x30
[<ffffffff81485c15>] bus_remove_device+0x105/0x180
[<ffffffff814822b9>] device_del+0x139/0x260
[<ffffffffa05e0ec5>] snd_hdac_device_unregister+0x25/0x30 [snd_hda_core]
[<ffffffffa074fa6a>] snd_hda_codec_reset+0x2a/0x70 [snd_hda_codec]
[<ffffffffa075007b>] snd_hda_codec_build_pcms+0x18b/0x1b0 [snd_hda_codec]
[<ffffffffa074a44e>] hda_codec_driver_probe+0xbe/0x140 [snd_hda_codec]
[<ffffffff81486ac4>] driver_probe_device+0x1f4/0x460
[<ffffffff81486dc0>] __driver_attach+0x90/0xa0
[<ffffffff81484844>] bus_for_each_dev+0x64/0xa0
[<ffffffff814862de>] driver_attach+0x1e/0x20
[<ffffffff81485e7b>] bus_add_driver+0x1eb/0x280
[<ffffffff81487680>] driver_register+0x60/0xe0
[<ffffffffa074a0da>] __hda_codec_driver_register+0x5a/0x60 [snd_hda_codec]
[<ffffffffa070a01e>] realtek_driver_init+0x1e/0x1000 [snd_hda_codec_realtek]
[<ffffffff810002f3>] do_one_initcall+0xb3/0x200
[<ffffffff816a1fc5>] do_init_module+0x60/0x1f8
[<ffffffff810ee5c3>] load_module+0x1653/0x1bd0
[<ffffffff810eed48>] SYSC_finit_module+0x98/0xc0
[<ffffffff810eed8e>] SyS_finit_module+0xe/0x10
[<ffffffff816aa032>] entry_SYSCALL_64_fastpath+0x16/0x75
The simple fix is just to remove this call, since we don't need to
think about unbinding at there any longer.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=948758
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Finally we have a proper infrastructure to generate the modaliases
automatically, let's move to hda_device_id from the legacy
hda_codec_preset that contains basically the same information.
The patch function hook is stored in driver_data field, which is long,
and we need an explicit cast. Other than that, the conversion is
mostly straightforward. Each entry is even simplified using a macro,
and the lengthy (and error-prone) manual modaliases got removed.
As a result, we achieved a quite good diet:
14 files changed, 407 insertions(+), 595 deletions(-)
Reviewed-by: Vinod Koul <vinod.koul@intel.com>
Tested-by: Subhransu S Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
More drm-misc for 4.4.
- fb refcount fix in atomic fbdev
- various locking reworks to reduce drm_global_mutex and dev->struct_mutex
- rename docbook to gpu.tmpl and include vga_switcheroo stuff, plus more
vga_switcheroo (Lukas Wunner)
- viewport check fixes for atomic drivers from Ville
- DRM_DEBUG_VBL from Ville
- non-contentious header fixes from Mikko Rapeli
- small things all over
* tag 'topic/drm-misc-2015-10-19' of git://anongit.freedesktop.org/drm-intel: (31 commits)
drm/fb-helper: Fix fb refcounting in pan_display_atomic
drm/fb-helper: Set plane rotation directly
drm: fix mutex leak in drm_dp_get_mst_branch_device
drm: Check plane src coordinates correctly during page flip for atomic drivers
drm: Check crtc viewport correctly with rotated primary plane on atomic drivers
drm: Refactor plane src coordinate checks
drm: Swap w/h when converting the mode to src coordidates for a rotated primary plane
drm: Don't leak fb when plane crtc coodinates are bad
ALSA: hda - Spell vga_switcheroo consistently
drm/gem: Use kref_get_unless_zero for the weak mmap references
drm/vgem: Drop vgem_drm_gem_mmap
drm: Fix return value of drm_framebuffer_init()
drm/gem: Use container_of in drm_gem_object_free
drm/gem: Check locking in drm_gem_object_unreference
drm/gem: Drop struct_mutex requirement from drm_gem_mmap_obj
drm/i810_drm.h: include drm/drm.h
r128_drm.h: include drm/drm.h
savage_drm.h: include <drm/drm.h>
gpu/doc: Convert to markdown harder
gpu/doc: Add vga_switcheroo documentation
...
- dmc fixes from Animesh (not yet all) for deeper sleep states
- piles of prep patches from Ville to make mmio functions type-safe
- more fbc work from Paulo all over
- w/a shuffling from Arun Siluvery
- first part of atomic watermark updates from Matt and Ville (later parts had to
be dropped again unfortunately)
- lots of patches to prepare bxt dsi support ( Shashank Sharma)
- userptr fixes from Chris
- audio rate interface between i915/snd_hda plus kerneldoc (Libin Yang)
- shrinker improvements and fixes (Chris Wilson)
- lots and lots of small patches all over
* tag 'drm-intel-next-2015-10-10' of git://anongit.freedesktop.org/drm-intel: (134 commits)
drm/i915: Update DRIVER_DATE to 20151010
drm/i915: Partial revert of atomic watermark series
drm/i915: Early exit from semaphore_waits_for for execlist mode.
drm/i915: Remove wrong warning from i915_gem_context_clean
drm/i915: Determine the stolen memory base address on gen2
drm/i915: fix FBC buffer size checks
drm/i915: fix CFB size calculation
drm/i915: remove pre-atomic check from SKL update_primary_plane
drm/i915: don't allocate fbcon from stolen memory if it's too big
Revert "drm/i915: Call encoder hotplug for init and resume cases"
Revert "drm/i915: Add hot_plug hook for hdmi encoder"
drm/i915: use error path
drm/i915/irq: Fix misspelled word register in kernel-doc
drm/i915/irq: Fix kernel-doc warnings
drm/i915: Hook up ring workaround writes at context creation time on Gen6-7.
drm/i915: Don't warn if the workaround list is empty.
drm/i915: Resurrect golden context on gen6/7
drm/i915/chv: remove pre-production hardware workarounds
drm/i915/snb: remove pre-production hardware workaround
drm/i915/bxt: Set time interval unit to 0.833us
...
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: http://patchwork.freedesktop.org/patch/msgid/9b0175319ce78d831acfcf11e4c6c760f826b0e3.1444663039.git.lukas@wunner.de
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The recent commit [7fbe824a0f: ALSA: hda - Update mixer name for the
lower codec address] tried to improve the mixer chip name assignment
in the order of codec address. However, this fix was utterly bogus;
it checks the field set in each codec, thus this value is reset at
each codec creation, of course. For really handling this priority,
the assignment has to be remembered in the common place, namely in
hda_bus, instead of hda_codec.
Fixes: 7fbe824a0f ('ALSA: hda - Update mixer name for the lower codec address')
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In most cases, we prefer the onboard codec as the primary device, thus
it's better to set it as the mixer name. Currently, however, the
mixer name is updated per the device instantiation order, and user
gets often HDMI/DP or other seen as a mixer chip name. Also, if a
codec name is renamed by the driver, the old chip name might be left
still as the mixer name.
This patch addresses these issues by remembering the chip address that
was referred as the mixer name. When a codec with the same or lower
address gives its name, renew the mixer name accordingly, as it's
either the update of the codec name or we get likely the more
appropriate chip as the reference.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few multiple codec drivers do renaming the chip_name string but all
these are open-coded and some of them have even no error check. Let's
make common helpers to do it properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cirrus codecs have also fine power controls on each widget, thus it
gets benefit from the recent widget power-saving feature. As we
haven't seen any obvious regressions with tests on some MacBooks,
let's try to enable it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we have introduced the core fns we should make hda use these
helpers
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Pull in the i915/hda changes for N/CTS setting so I can apply the
follow-up documentation work for drm/i915.
Some conflicts because ofc we had to rework i915 while that N/CTS work
was going on. But not more than adjacent changes really.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The recent widget power saving introduced some unavoidable click
noises on old IDT 92HD73xx chips while it still seems working on the
compatible new chips. In the bugzilla, we tried lots of tests and
workarounds, but they didn't help much. So, let's disable the feature
for these specific chips as the least (but safest) fix.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=104981
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The MacBookPro 12,1 has the same setup as the 11 for controlling the
status of the optical audio light. Simply apply the existing workaround
to the subsystem ID for the 12,1.
[sorted the fixup entry by tiwai]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=105401
Signed-off-by: John Flatness <john@zerocrates.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Much like all the other Lenovo laptops, add a quirk to make
sound work with docking.
Reported-and-tested-by: lacknerflo@gmail.com
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Another attempt at drm-misc for 4.4 ...
- better atomic helpers for runtime pm drivers
- atomic fbdev
- dp aux i2c STATUS_UPDATE handling (for short i2c replies from the sink)
- bunch of constify patches
- inital kerneldoc for vga switcheroo
- some vblank code cleanups from Ville and Thierry
- various polish all over
* tag 'topic/drm-misc-2015-09-25' of git://anongit.freedesktop.org/drm-intel: (57 commits)
drm/irq: Add drm_crtc_vblank_count_and_time()
drm/irq: Rename drm_crtc -> crtc
drm: drm_atomic_crtc_get_property should be static
drm/gma500: Remove DP_LINK_STATUS_SIZE redefinition
vga_switcheroo: Set active attribute to false for audio clients
drm/core: Preserve the fb id on close.
drm/core: Preserve the framebuffer after removing it.
drm: Use vblank timestamps to guesstimate how many vblanks were missed
drm: store_vblank() is never called with NULL timestamp
drm: Clean up drm_calc_vbltimestamp_from_scanoutpos() vbl_status
drm: Limit the number of .get_vblank_counter() retries
drm: Pass flags to drm_update_vblank_count()
drm/i915: Fix vblank count variable types
drm: Kill pixeldur_ns
drm: Stop using linedur_ns and pixeldur_ns for vblank timestamps
drm: Move timestamping constants into drm_vblank_crtc
drm/fbdev: Update legacy plane->fb refcounting for atomic restore
drm: fix kernel-doc warnings in drm_crtc.h
vga_switcheroo: Sort headers alphabetically
drm: Spell vga_switcheroo consistently
...
For display audio, call the sync_audio_rate callback function
to do the synchronization between gfx driver and audio driver.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Thinkpads with recent Realtek codecs seem suffering from click
noises at power transition since the introduction of widget power
saving in 4.1 kernel. Although this might be solved by some delays in
appropriate points, as a quick workaround, just disable the
power_save_node feature for now. The gain it gives is relatively
small, and this makes the situation back to pre 4.1 time.
This patch ended up with a bit more code changes than usual because
the existing fixup for Thinkpads is highly chained. Instead of adding
yet another chain, combine a few of them into a single fixup entry, as
a gratis cleanup.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=943982
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
