The while loop in sonic_rx() traverses the rx descriptor ring. It stops
when it reaches a descriptor that the SONIC has not used. Each iteration
advances the EOL flag so the SONIC can keep using more descriptors.
Therefore, the while loop has no definite termination condition.
The algorithm described in the National Semiconductor literature is quite
different. It consumes descriptors up to the one with its EOL flag set
(which will also have its "in use" flag set). All freed descriptors are
then returned to the ring at once, by adjusting the EOL flags (and link
pointers).
Adopt the algorithm from datasheet as it's simpler, terminates quickly
and avoids a lot of pointless descriptor EOL flag changes.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SONIC can sometimes advance its rx buffer pointer (RRP register)
without advancing its rx descriptor pointer (CRDA register). As a result
the index of the current rx descriptor may not equal that of the current
rx buffer. The driver mistakenly assumes that they are always equal.
This assumption leads to incorrect packet lengths and possible packet
duplication. Avoid this by calling a new function to locate the buffer
corresponding to a given descriptor.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_aborted_errors statistic should count packets flagged with EXD,
EXC, FU, or BCM bits because those bits denote an aborted transmission.
That corresponds to the bitmask 0x0446, not 0x0642. Use macros for these
constants to avoid mistakes. Better to leave out FIFO Underruns (FU) as
there's a separate counter for that purpose.
Don't lump all these errors in with the general tx_errors counter as
that's used for tx timeout events.
On the rx side, don't count RDE and RBAE interrupts as dropped packets.
These interrupts don't indicate a lost packet, just a lack of resources.
When a lack of resources results in a lost packet, this gets reported
in the rx_missed_errors counter (along with RFO events).
Don't double-count rx_frame_errors and rx_crc_errors.
Don't use the general rx_errors counter for events that already have
special counters.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver accesses descriptor memory which is simultaneously accessed by
the chip, so the compiler must not be allowed to re-order CPU accesses.
sonic_buf_get() used 'volatile' to prevent that. sonic_buf_put() should
have done so too but was overlooked.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip can change a packet's descriptor status flags at any time.
However, an active interrupt flag gets cleared rather late. This
allows a race condition that could theoretically lose an interrupt.
Fix this by clearing asserted interrupt flags immediately.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_stop_queue() call in sonic_send_packet() races with the
netif_wake_queue() call in sonic_interrupt(). This causes issues
like "NETDEV WATCHDOG: eth0 (macsonic): transmit queue 0 timed out".
Fix this by disabling interrupts when accessing tx_skb[] and next_tx.
Update a comment to clarify the synchronization properties.
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the only 10G PHY interface type defined at the moment the code
was developed was XGMII, although the PHY interface mode used was
not XGMII, XGMII was used in the code to denote 10G. This patch
renames the 10G interface mode to remove the ambiguity.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fsl,erratum-a011043 is set, adjust for erratum A011043:
MDIO reads to internal PCS registers may result in having
the MDIO_CFG[MDIO_RD_ER] bit set, even when there is no
error and read data (MDIO_DATA[MDIO_DATA]) is correct.
Software may get false read error when reading internal
PCS registers through MDIO. As a workaround, all internal
MDIO accesses should ignore the MDIO_CFG[MDIO_RD_ER] bit.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver while collecting firmware dump takes longer time to
collect/process some of the firmware dump entries/memories.
Bigger capture masks makes it worse as it results in larger
amount of data being collected and results in CPU soft lockup.
Place cond_resched() in some of the driver flows that are
expectedly time consuming to relinquish the CPU to avoid CPU
soft lockup panic.
Signed-off-by: Shahed Shaikh <shshaikh@marvell.com>
Tested-by: Yonggen Xu <Yonggen.Xu@dell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During reload (or module unload), the router block is de-initialized.
Among other things, this results in the removal of a default multicast
route from each active virtual router (VRF). These default routes are
configured during initialization to trap packets to the CPU. In
Spectrum-2, unlike Spectrum-1, multicast routes are implemented using
ACL rules.
Since the router block is de-initialized before the ACL block, it is
possible that the ACL rules corresponding to the default routes are
deleted while being accessed by the ACL delayed work that queries rules'
activity from the device. This can result in a rare use-after-free [1].
Fix this by protecting the rules list accessed by the delayed work with
a lock. We cannot use a spinlock as the activity read operation is
blocking.
[1]
[ 123.331662] ==================================================================
[ 123.339920] BUG: KASAN: use-after-free in mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.349381] Read of size 8 at addr ffff8881f3bb4520 by task kworker/0:2/78
[ 123.357080]
[ 123.358773] CPU: 0 PID: 78 Comm: kworker/0:2 Not tainted 5.5.0-rc5-custom-33108-gf5df95d3ef41 #2209
[ 123.368898] Hardware name: Mellanox Technologies Ltd. MSN3700C/VMOD0008, BIOS 5.11 10/10/2018
[ 123.378456] Workqueue: mlxsw_core mlxsw_sp_acl_rule_activity_update_work
[ 123.385970] Call Trace:
[ 123.388734] dump_stack+0xc6/0x11e
[ 123.392568] print_address_description.constprop.4+0x21/0x340
[ 123.403236] __kasan_report.cold.8+0x76/0xb1
[ 123.414884] kasan_report+0xe/0x20
[ 123.418716] mlxsw_sp_acl_rule_activity_update_work+0x330/0x3b0
[ 123.444034] process_one_work+0xb06/0x19a0
[ 123.453731] worker_thread+0x91/0xe90
[ 123.467348] kthread+0x348/0x410
[ 123.476847] ret_from_fork+0x24/0x30
[ 123.480863]
[ 123.482545] Allocated by task 73:
[ 123.486273] save_stack+0x19/0x80
[ 123.490000] __kasan_kmalloc.constprop.6+0xc1/0xd0
[ 123.495379] mlxsw_sp_acl_rule_create+0xa7/0x230
[ 123.500566] mlxsw_sp2_mr_tcam_route_create+0xf6/0x3e0
[ 123.506334] mlxsw_sp_mr_tcam_route_create+0x5b4/0x820
[ 123.512102] mlxsw_sp_mr_table_create+0x3b5/0x690
[ 123.517389] mlxsw_sp_vr_get+0x289/0x4d0
[ 123.521797] mlxsw_sp_fib_node_get+0xa2/0x990
[ 123.526692] mlxsw_sp_router_fib4_event_work+0x54c/0x2d60
[ 123.532752] process_one_work+0xb06/0x19a0
[ 123.537352] worker_thread+0x91/0xe90
[ 123.541471] kthread+0x348/0x410
[ 123.545103] ret_from_fork+0x24/0x30
[ 123.549113]
[ 123.550795] Freed by task 518:
[ 123.554231] save_stack+0x19/0x80
[ 123.557958] __kasan_slab_free+0x125/0x170
[ 123.562556] kfree+0xd7/0x3a0
[ 123.565895] mlxsw_sp_acl_rule_destroy+0x63/0xd0
[ 123.571081] mlxsw_sp2_mr_tcam_route_destroy+0xd5/0x130
[ 123.576946] mlxsw_sp_mr_tcam_route_destroy+0xba/0x260
[ 123.582714] mlxsw_sp_mr_table_destroy+0x1ab/0x290
[ 123.588091] mlxsw_sp_vr_put+0x1db/0x350
[ 123.592496] mlxsw_sp_fib_node_put+0x298/0x4c0
[ 123.597486] mlxsw_sp_vr_fib_flush+0x15b/0x360
[ 123.602476] mlxsw_sp_router_fib_flush+0xba/0x470
[ 123.607756] mlxsw_sp_vrs_fini+0xaa/0x120
[ 123.612260] mlxsw_sp_router_fini+0x137/0x384
[ 123.617152] mlxsw_sp_fini+0x30a/0x4a0
[ 123.621374] mlxsw_core_bus_device_unregister+0x159/0x600
[ 123.627435] mlxsw_devlink_core_bus_device_reload_down+0x7e/0xb0
[ 123.634176] devlink_reload+0xb4/0x380
[ 123.638391] devlink_nl_cmd_reload+0x610/0x700
[ 123.643382] genl_rcv_msg+0x6a8/0xdc0
[ 123.647497] netlink_rcv_skb+0x134/0x3a0
[ 123.651904] genl_rcv+0x29/0x40
[ 123.655436] netlink_unicast+0x4d4/0x700
[ 123.659843] netlink_sendmsg+0x7c0/0xc70
[ 123.664251] __sys_sendto+0x265/0x3c0
[ 123.668367] __x64_sys_sendto+0xe2/0x1b0
[ 123.672773] do_syscall_64+0xa0/0x530
[ 123.676892] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 123.682552]
[ 123.684238] The buggy address belongs to the object at ffff8881f3bb4500
[ 123.684238] which belongs to the cache kmalloc-128 of size 128
[ 123.698261] The buggy address is located 32 bytes inside of
[ 123.698261] 128-byte region [ffff8881f3bb4500, ffff8881f3bb4580)
[ 123.711303] The buggy address belongs to the page:
[ 123.716682] page:ffffea0007ceed00 refcount:1 mapcount:0 mapping:ffff888236403500 index:0x0
[ 123.725958] raw: 0200000000000200 dead000000000100 dead000000000122 ffff888236403500
[ 123.734646] raw: 0000000000000000 0000000000100010 00000001ffffffff 0000000000000000
[ 123.743315] page dumped because: kasan: bad access detected
[ 123.749562]
[ 123.751241] Memory state around the buggy address:
[ 123.756620] ffff8881f3bb4400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.764716] ffff8881f3bb4480: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.772812] >ffff8881f3bb4500: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 123.780904] ^
[ 123.785697] ffff8881f3bb4580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 123.793793] ffff8881f3bb4600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 123.801883] ==================================================================
Fixes: cf7221a4f5 ("mlxsw: spectrum_router: Add Multicast routing support for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A queue can't belong to multiple traffic classes. So, reject
any such configuration that results in overlapped queues for a
traffic class.
Fixes: b1396c2bd6 ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
T6 can support 2 egress traffic management channels per port to
double the total number of traffic classes that can be configured.
In this configuration, if the class belongs to the other channel,
then all the queues must be bound again explicitly to the new class,
for the rate limit parameters on the other channel to take effect.
So, always explicitly bind all queues to the port rate limit traffic
class, regardless of the traffic management channel that it belongs
to. Also, only bind queues to port rate limit traffic class, if all
the queues don't already belong to an existing different traffic
class.
Fixes: 4ec4762d8e ("cxgb4: add TC-MATCHALL classifier egress offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSN read can fail, for example on a kdump kernel without PCIe extended
config space support. If DSN read fails, don't set the
BNXT_FLAG_DSN_VALID flag and continue loading. Check the flag
to see if the stored DSN is valid before using it. Only VF reps
creation should fail without valid DSN.
Fixes: 03213a9965 ("bnxt: move bp->switch_id initialization to PF probe")
Reported-by: Marc Smith <msmith626@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bnxt_fltr_match() to match ipv6 source and destination addresses.
The function currently only checks ipv4 addresses and will not work
corrently on ipv6 filters.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NTUPLE related firmware commands are sent to the wrong firmware
channel, causing all these commands to fail on new firmware that
supports the new firmware channel. Fix it by excluding the 3
NTUPLE firmware commands from the list for the new firmware channel.
Fixes: 760b6d3341 ("bnxt_en: Add support for 2nd firmware message channel.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We would not be transmitting using the correct SYSTEMPORT transmit queue
during ndo_select_queue() which looks up the internal TX ring map
because while establishing the mapping we would be off by 4, so for
instance, when we populate switch port mappings we would be doing:
switch port 0, queue 0 -> ring index #0
switch port 0, queue 1 -> ring index #1
...
switch port 0, queue 3 -> ring index #3
switch port 1, queue 0 -> ring index #8 (4 + 4 * 1)
...
instead of using ring index #4. This would cause our ndo_select_queue()
to use the fallback queue mechanism which would pick up an incorrect
ring for that switch port. Fix this by using the correct switch queue
number instead of SYSTEMPORT queue number.
Fixes: 25c4407046 ("net: systemport: Simplify queue mapping logic")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is not enough memory and napi_alloc_skb() return NULL,
the HNS driver will print error message, and than try again, if
the memory is not enough for a while, huge error message and the
retry operation will cause soft lockup.
When napi_alloc_skb() return NULL because of no memory, we can
get a warn_alloc() call trace, so this patch deletes the error
message. We already use polling mode to handle irq, but the
retry operation will render the polling weight inactive, this
patch just return budget when the rx is not completed to avoid
dead loop.
Fixes: 36eedfde1a ("net: hns: Optimize hns_nic_common_poll for better performance")
Fixes: b5996f11ea ("net: add Hisilicon Network Subsystem basic ethernet support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building with PROVE_LOCKING=y, lockdep shows the following
dump message.
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
...
Calling device_set_wakeup_enable() directly occurs this issue,
and it isn't necessary for initialization, so this patch creates
internal function __ave_ethtool_set_wol() and replaces with this
in ave_init() and ave_resume().
Fixes: 7200f2e3c9 ("net: ethernet: ave: Set initial wol state to disabled")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can not handle short frames below or equal to 32
bytes according to the hardware user manual, and it will trigger
a RAS error when the frame's length is below 33 bytes.
This patch pads the SKB when skb->len is below 33 bytes before
sending it to hardware.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When HW does not support perfect filtering the feature will not be
enabled in the net_device. Add a check for this to prevent failures.
Fixes: 1b2250a04c ("net: stmmac: selftests: Add tests for VLAN Perfect Filtering")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the VLAN ID does not match the expected one it means filter failed
in HW. Fix it.
Fixes: 94e1838200 ("net: stmmac: selftests: Add selftest for VLAN TX Offload")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synopsys AXS101 boards do not support unaligned memory loads or stores.
Change the selftests mechanism to explicity:
- Not add extra alignment in TX SKB
- Use the unaligned version of ether_addr_equal()
Fixes: 091810dbde ("net: stmmac: Introduce selftests support")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw configures Spectrum in such a way that BUM traffic is passed not
through its nominal traffic class TC, but through its MC counterpart TC+8.
However, when collecting statistics, Qdiscs only look at the nominal TC and
ignore the MC TC.
Add two helpers to compute the value for logical TC from the constituents,
one for backlog, the other for tail drops. Use them throughout instead of
going through the xstats pointer directly.
Counters for TX bytes and packets are deduced from packet priority
counters, and therefore already include BUM traffic. wred_drop counter is
irrelevant on MC TCs, because RED is not enabled on them.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per-port counter cache used by Qdiscs is updated periodically, unless the
port is down. The fact that the cache is not updated for down ports is no
problem for most counters, which are relative in nature. However, backlog
is absolute in nature, and if there is a non-zero value in the cache around
the time that the port goes down, that value just stays there. This value
then leaks to offloaded Qdiscs that report non-zero backlog even if
there (obviously) is no traffic.
The HW does not keep backlog of a downed port, so do likewise: as the port
goes down, wipe the backlog value from xstats.
Fixes: 075ab8adaf ("mlxsw: spectrum: Collect tclass related stats periodically")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 31557f0f97 ("mlxsw: Introduce Mellanox SwitchX-2 ASIC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs to prepend a Tx header to each packet it is
transmitting. The header includes information such as the egress port
and traffic class.
The addition of the header requires the driver to modify the SKB's
header and therefore it must not be shared. Otherwise, we risk hitting
various race conditions.
For example, when a packet is flooded (cloned) by the bridge driver to
two switch ports swp1 and swp2:
t0 - mlxsw_sp_port_xmit() is called for swp1. Tx header is prepended with
swp1's port number
t1 - mlxsw_sp_port_xmit() is called for swp2. Tx header is prepended with
swp2's port number, overwriting swp1's port number
t2 - The device processes data buffer from t0. Packet is transmitted via
swp2
t3 - The device processes data buffer from t1. Packet is transmitted via
swp2
Usually, the device is fast enough and transmits the packet before its
Tx header is overwritten, but this is not the case in emulated
environments.
Fix this by making sure the SKB's header is writable by calling
skb_cow_head(). Since the function ensures we have headroom to push the
Tx header, the check further in the function can be removed.
v2:
* Use skb_cow_head() instead of skb_unshare() as suggested by Jakub
* Remove unnecessary check regarding headroom
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a72afb6879 ("mlxsw: Enforce firmware version for
Spectrum-2") I added a required firmware version for Spectrum-2, but
missed the fact that mlxsw_sp2_init() is used by both Spectrum-2 and
Spectrum-3. This means that the same firmware version will be used for
both, which is wrong.
Fix this by creating a new init() callback for Spectrum-3.
Fixes: a72afb6879 ("mlxsw: Enforce firmware version for Spectrum-2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Page pool API will start syncing (if requested) starting from
page->dma_addr + pool->p.offset. Fix dma sync length in
mvneta_run_xdp since we do not need to account xdp headroom
Fixes: 07e13edbb6 ("net: mvneta: get rid of huge dma sync in mvneta_rx_refill")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the issue with fixed link. With fixed-link
device opening fails due to macb_phylink_connect not
handling fixed-link mode, in which case no MAC-PHY connection
is needed and phylink_connect return success (0), however
in current driver attempt is made to search and connect to
PHY even for fixed-link.
Fixes: 7897b071ac ("net: macb: convert to phylink")
Signed-off-by: Milind Parab <mparab@cadence.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The function to obtain a unique snapshot id was mistakenly typo'd as
devlink_region_shapshot_id_get. Fix this typo by renaming the function
and all of its users.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSS, when enabled, will bypass the L3 and L4 filtering causing it not
to work. Add a check before trying to setup the filters.
Fixes: 425eabddaf ("net: stmmac: Implement L3/L4 Filters using TC Flower")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are disabling RSS on HW but not updating the internal private status
to the 'disabled' state. This is needed for next tc commit that will
check if RSS is disabled before trying to apply filters.
Fixes: 4647e02119 ("net: stmmac: selftests: Add selftest for L3/L4 Filters")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2020-01-09
This series contains fixes to e1000e, igb, ixgbe, ixgbevf, i40e and iavf
drivers.
Brett fixes the validation of the virtchnl queue select bitmaps by
comparing the bitmaps against BIT(I40E_MAX_VF_QUEUES).
Radoslaw removes the limitation of only 10 filter entries for a VF and
allows use of all free RAR entries for the forwarding database, if
needed.
Cambda Zhu fixes the calculation of queue when restoring flow director
filters after resetting the adapter for ixgbe.
Manfred Rudigier fixes the SGMIISFP module discovery for 100FX/LX
modules for igb.
Stefan Assmann fixes iavf where during a VF reset event, MAC filters
were not altered, which could lead to a stale filter when an
administratively set MAC address is forced by the PF.
Adam adds the missing code to set the PHY access flag on X722 devices,
which supports accessing PHY registers with the admin queue command.
Revert a previous commit for e1000e to use "delayed work" which was
causing connections to reset unexpectedly and possible driver crashes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When adding the sh_eth_cpu_data::dual_port flag I forgot to add the flag
checks to __sh_eth_get_regs(), causing the non-existing TSU registers to
be dumped by 'ethtool' on the single port Ether controllers having TSU...
Fixes: a94cf2a614 ("sh_eth: fix TSU init on SH7734/R8A7740")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 59653e6497.
This is due to this commit causing driver crashes and connections to
reset unexpectedly.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
The X722 FW API version 1.9 adds support for accessing PHY
registers with Admin Queue Command. This enables reading
EEPROM data from (Q)SFP+ transceivers, what was previously
possible only on X710 devices.
Signed-off-by: Adam Ludkiewicz <adam.ludkiewicz@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently MAC filters are not altered during a VF reset event. This may
lead to a stale filter when an administratively set MAC is forced by the
PF.
For an administratively set MAC the PF driver deletes the VFs filters,
overwrites the VFs MAC address and triggers a VF reset. However
the VF driver itself is not aware of the filter removal, which is what
the VF reset is for.
The VF reset queues all filters present in the VF driver to be re-added
to the PF filter list (including the filter for the now stale VF MAC
address) and triggers a VIRTCHNL_OP_GET_VF_RESOURCES event, which
provides the new MAC address to the VF.
When this happens i40e will complain and reject the stale MAC filter,
at least in the untrusted VF case.
i40e 0000:08:00.0: Setting MAC 3c:fa:fa:fa:fa:01 on VF 0
iavf 0000:08:02.0: Reset warning received from the PF
iavf 0000:08:02.0: Scheduling reset task
i40e 0000:08:00.0: Bring down and up the VF interface to make this change effective.
i40e 0000:08:00.0: VF attempting to override administratively set MAC address, bring down and up the VF interface to resume normal operation
i40e 0000:08:00.0: VF 0 failed opcode 10, retval: -1
iavf 0000:08:02.0: Failed to add MAC filter, error IAVF_ERR_NVM
To avoid re-adding the stale MAC filter it needs to be removed from the
VF driver's filter list before queuing the existing filters. Then during
the VIRTCHNL_OP_GET_VF_RESOURCES event the correct filter needs to be
added again, at which point the MAC address has been updated.
As a bonus this change makes bringing the VF down and up again
superfluous for the administratively set MAC case.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Changing the link mode should also be done for 100BaseFX SGMII modules,
otherwise they just don't work when the default link mode in CTRL_EXT
coming from the EEPROM is SERDES.
Additionally 100Base-LX SGMII SFP modules are also supported now, which
was not the case before.
Tested with an i210 using Flexoptix S.1303.2M.G 100FX and
S.1303.10.G 100LX SGMII SFP modules.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the calculation of queue when we restore flow director
filters after resetting adapter. In ixgbe_fdir_filter_restore(), filter's
vf may be zero which makes the queue outside of the rx_ring array.
The calculation is changed to the same as ixgbe_add_ethtool_fdir_entry().
Signed-off-by: Cambda Zhu <cambda@linux.alibaba.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, though the FDB entry is added to VF, it does not appear in
RAR filters. VF driver only allows to add 10 entries. Attempting to add
another causes an error. This patch removes limitation and allows use of
all free RAR entries for the FDB if needed.
Fixes: 46ec20ff7d ("ixgbevf: Add macvlan support in the set rx mode op")
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Acked-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently in i40e_vc_disable_queues_msg() we are incorrectly
validating the virtchnl queue select bitmaps. The
virtchnl_queue_select rx_queues and tx_queue bitmap is being
compared against ICE_MAX_VF_QUEUES, but the problem is that
these bitmaps can have a value greater than I40E_MAX_VF_QUEUES.
Fix this by comparing the bitmaps against BIT(I40E_MAX_VF_QUEUES).
Also, add the function i40e_vc_validate_vqs_bitmaps() that checks to see
if both virtchnl_queue_select bitmaps are empty along with checking that
the bitmaps only have valid bits set. This function can then be used in
both the queue enable and disable flows.
Suggested-by: Arkady Gilinksky <arkady.gilinsky@harmonicinc.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The following patch will change PRIO to replace a removed Qdisc with an
invisible FIFO, instead of NOOP. mlxsw will see this replacement due to the
graft message that is generated. But because FIFO does not issue its own
REPLACE message, when the graft operation takes place, the Qdisc that mlxsw
tracks under the indicated band is still the old one. The child
handle (0:0) therefore does not match, and mlxsw rejects the graft
operation, which leads to an extack message:
Warning: Offloading graft operation failed.
Fix by ignoring the invisible children in the PRIO graft handler. The
DESTROY message of the removed Qdisc is going to follow shortly and handle
the removal.
Fixes: 32dc5efc6c ("mlxsw: spectrum: qdiscs: prio: Handle graft command")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all the RGMII modes to be used. This would allow us to represent
the hardware better in the device tree with RGMII_ID where in most
cases the PHY's internal delay for both RX and TX are used.
Fixes: af0bd4e9ba ("net: stmmac: sunxi platform extensions for GMAC in Allwinner A20 SoC's")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using fixed link we don't need the MDIO bus support.
Reported-by: Heiko Stuebner <heiko@sntech.de>
Reported-by: kernelci.org bot <bot@kernelci.org>
Fixes: d3e014ec7d ("net: stmmac: platform: Fix MDIO init for platforms without PHY")
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Acked-by: Sriram Dash <Sriram.dash@samsung.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail> # Lamobo R1 (fixed-link + MDIO sub node for roboswitch).
Signed-off-by: David S. Miller <davem@davemloft.net>
Add one notifier for udev changes net device name.
Fixes: b6601323ef9e ("net: stmmac: debugfs entry name is not be changed when udev rename")
Signed-off-by: Jiping Ma <jiping.ma2@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever adding new member of rule object we attach it to 2 lists,
These 2 lists should be initialized first.
Fixes: 41d0707415 ("net/mlx5: DR, Expose steering rule functionality")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Set hairpin table size to the corret size, based on the groups that
would be created in it. Groups are laid out on the table such that a
group occupies a range of entries in the table. This implies that the
group ranges should have correspondence to the table they are laid upon.
The patch cited below made group 1's size to grow hence causing
overflow of group range laid on the table.
Fixes: a795d8db2a ("net/mlx5e: Support RSS for IP-in-IP and IPv6 tunneled packets")
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
No need for an atomic refcounter for the STE and hashtables.
These are internal SW steering resources and they are always
under domain mutex.
This also fixes the following refcount error:
refcount_t: addition on 0; use-after-free.
WARNING: CPU: 9 PID: 3527 at lib/refcount.c:25 refcount_warn_saturate+0x81/0xe0
Call Trace:
dr_table_init_nic+0x10d/0x110 [mlx5_core]
mlx5dr_table_create+0xb4/0x230 [mlx5_core]
mlx5_cmd_dr_create_flow_table+0x39/0x120 [mlx5_core]
__mlx5_create_flow_table+0x221/0x5f0 [mlx5_core]
esw_create_offloads_fdb_tables+0x180/0x5a0 [mlx5_core]
...
Fixes: 26d688e33f ("net/mlx5: DR, Add Steering entry (STE) utilities")
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
