This commit is similar to commit 4d12bc63ab ("net: mvneta: fix
operation in 10 Mbit/s mode"), but this time for the mvpp2 driver. The
driver was properly taking into account the 1 Gbit/s and 100 Mbit/s
speeds, but not the 10 Mbit/s, which was handled as 100
Mbit/s. However, the MVPP2_GMAC_CONFIG_MII_SPEED bit in the
MVPP2_GMAC_AUTONEG_CONFIG register must remain cleared to allow 10
Mbit/s operation. This commit therefore fixes 10 Mbit/s operation.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse warns because of implicit pointer cast.
v2: subject line correction, space between "void" and "*"
Signed-off-by: Karoly Kemeny <karoly.kemeny@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of the macro IS_ERR_OR_NULL in place of
tests for NULL and IS_ERR.
The following Coccinelle semantic patch was used for making the change:
@@
expression e;
@@
- e == NULL || IS_ERR(e)
+ IS_ERR_OR_NULL(e)
|| ...
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of the macro IS_ERR_OR_NULL in place of
tests for NULL and IS_ERR.
The following Coccinelle semantic patch was used for making the change:
@@
expression e;
@@
- e == NULL || IS_ERR(e)
+ IS_ERR_OR_NULL(e)
|| ...
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of the macro IS_ERR_OR_NULL in place of
tests for NULL and IS_ERR.
The following Coccinelle semantic patch was used for making the change:
@@
expression e;
@@
- e == NULL || IS_ERR(e)
+ IS_ERR_OR_NULL(e)
|| ...
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
__iowrite64_copy() isn't quite the same as efx_memcpy_64(), but
it looks close enough:
- The length is in units of qwords not bytes
- It never byte-swaps, but that doesn't make a difference now as PIO
is only enabled for x86_64
- It doesn't include any memory barriers, but that's OK as there is a
barrier just before pushing the doorbell
- mlx4_en uses it for the same purpose
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
moved the call to phy_scan_fixups() in phy_init_hw() after a software
reset is performed.
By the time phy_init_hw() is called in phy_device_register(), no driver
has been bound to this PHY yet, so all the checks in phy_init_hw()
against the PHY driver and the PHY driver's config_init function will
return 0. We will therefore never call phy_scan_fixups() as we should.
Fix this by calling phy_scan_fixups() and check for its return value to
restore the intended functionality.
This broke PHY drivers which do register an early PHY fixup callback to
intercept the PHY probing and do things like changing the 32-bits unique
PHY identifier when a pseudo-PHY address has been used, as well as
board-specific PHY fixups that need to be applied during driver probe
time.
Reported-by: Hauke Merthens <hauke-m@hauke-m.de>
Reported-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are devices that don't do reset all the way. So the packet filter should
be set to a sane initial value. Failure to do so leads to intermittent failures
of DHCP on some systems under some conditions.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device needs to be reset to recover from a timeout.
Unfortunately this can be handled only at the level of
the subdrivers.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sasha's report:
> While fuzzing with trinity inside a KVM tools guest running the latest -next
> kernel with the KASAN patchset, I've stumbled on the following spew:
>
> [ 4448.949424] ==================================================================
> [ 4448.951737] AddressSanitizer: user-memory-access on address 0
> [ 4448.952988] Read of size 2 by thread T19638:
> [ 4448.954510] CPU: 28 PID: 19638 Comm: trinity-c76 Not tainted 3.16.0-rc4-next-20140711-sasha-00046-g07d3099-dirty #813
> [ 4448.956823] ffff88046d86ca40 0000000000000000 ffff880082f37e78 ffff880082f37a40
> [ 4448.958233] ffffffffb6e47068 ffff880082f37a68 ffff880082f37a58 ffffffffb242708d
> [ 4448.959552] 0000000000000000 ffff880082f37a88 ffffffffb24255b1 0000000000000000
> [ 4448.961266] Call Trace:
> [ 4448.963158] dump_stack (lib/dump_stack.c:52)
> [ 4448.964244] kasan_report_user_access (mm/kasan/report.c:184)
> [ 4448.965507] __asan_load2 (mm/kasan/kasan.c:352)
> [ 4448.966482] ? netlink_sendmsg (net/netlink/af_netlink.c:2339)
> [ 4448.967541] netlink_sendmsg (net/netlink/af_netlink.c:2339)
> [ 4448.968537] ? get_parent_ip (kernel/sched/core.c:2555)
> [ 4448.970103] sock_sendmsg (net/socket.c:654)
> [ 4448.971584] ? might_fault (mm/memory.c:3741)
> [ 4448.972526] ? might_fault (./arch/x86/include/asm/current.h:14 mm/memory.c:3740)
> [ 4448.973596] ? verify_iovec (net/core/iovec.c:64)
> [ 4448.974522] ___sys_sendmsg (net/socket.c:2096)
> [ 4448.975797] ? put_lock_stats.isra.13 (./arch/x86/include/asm/preempt.h:98 kernel/locking/lockdep.c:254)
> [ 4448.977030] ? lock_release_holdtime (kernel/locking/lockdep.c:273)
> [ 4448.978197] ? lock_release_non_nested (kernel/locking/lockdep.c:3434 (discriminator 1))
> [ 4448.979346] ? check_chain_key (kernel/locking/lockdep.c:2188)
> [ 4448.980535] __sys_sendmmsg (net/socket.c:2181)
> [ 4448.981592] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2600)
> [ 4448.982773] ? trace_hardirqs_on (kernel/locking/lockdep.c:2607)
> [ 4448.984458] ? syscall_trace_enter (arch/x86/kernel/ptrace.c:1500 (discriminator 2))
> [ 4448.985621] ? trace_hardirqs_on_caller (kernel/locking/lockdep.c:2600)
> [ 4448.986754] SyS_sendmmsg (net/socket.c:2201)
> [ 4448.987708] tracesys (arch/x86/kernel/entry_64.S:542)
> [ 4448.988929] ==================================================================
This reports means that we've come to netlink_sendmsg() with msg->msg_name == NULL and msg->msg_namelen > 0.
After this report there was no usual "Unable to handle kernel NULL pointer dereference"
and this gave me a clue that address 0 is mapped and contains valid socket address structure in it.
This bug was introduced in f3d3342602
(net: rework recvmsg handler msg_name and msg_namelen logic).
Commit message states that:
"Set msg->msg_name = NULL if user specified a NULL in msg_name but had a
non-null msg_namelen in verify_iovec/verify_compat_iovec. This doesn't
affect sendto as it would bail out earlier while trying to copy-in the
address."
But in fact this affects sendto when address 0 is mapped and contains
socket address structure in it. In such case copy-in address will succeed,
verify_iovec() function will successfully exit with msg->msg_namelen > 0
and msg->msg_name == NULL.
This patch fixes it by setting msg_namelen to 0 if msg_name == NULL.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Eric Dumazet <edumazet@google.com>
Cc: <stable@vger.kernel.org>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a lack of usb_put_dev(udev) on failure path in gigaset_probe().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cong Wang says:
====================
net: forbid net devices named "all" "default" or "config"
/proc/sys/net/ipv[46]/conf/<dev> could conflict with
/proc/sys/net/ipv[46]/conf/(all|default). And /proc/net/vlan/<dev>
could conflict with /proc/net/vlan/config. Besides kernel warnings,
undefined behavior such as duplicated proc files also appears, therefore
we should forbid these names.
v2: introduce a helper function, suggested by Florian
fix error handling for ipv6_add_dev() in addrconf_init()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly, vlan will create /proc/net/vlan/<dev>, so when we
create dev with name "config", it will confict with
/proc/net/vlan/config.
Reported-by: Stephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a proc dir for each network device, this will cause
conflicts when the devices have name "all" or "default".
Rather than emitting an ugly kernel warning, we could just
fail earlier by checking the device name.
Reported-by: Stephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We create a proc dir for each network device, this will cause
conflicts when the devices have name "all" or "default".
Rather than emitting an ugly kernel warning, we could just
fail earlier by checking the device name.
Reported-by: Stephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Willem de Bruijn says:
====================
net: remove deprecated syststamp
The network stack can generate two kinds of hardware timestamps:
- hwtstamp stores a hw timestamp in device-specific raw format
- syststamp convers the raw format to system time
The second is deprecated and only implemented by a single device
driver. The suggested alternative is to communicate hwtstamp +
directly expose the NIC PTP clock device through ptp_clock_info.
The remaining driver (octeon) does not expose such a standard
interface as of now. It does have its own PTP library that depends
on its own shared memory PTP clock interface.
This patchset
1. reverts the syststamp code in the one driver (octeon)
2. reverts an unnecessary zero initialization in another (vxge)
3. modifies PF_PACKET to use syststamp is != 0 (because always == 0)
4. modifies SCM_TIMESTAMPING in the same way
For backwards compatibility, the interfaces are not removed.
Applications can still request SOF_TIMESTAMPING_SYS_HARDWARE. The
response field in scm_timestamping also remains. As was the case
for hardware/drivers that did not implement the feature, the
setsockopt succeeds, but the response field is always zero.
====================
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SO_TIMESTAMPING API defines three types of timestamps: software,
hardware in raw format (hwtstamp) and hardware converted to system
format (syststamp). The last has been deprecated in favor of combining
hwtstamp with a PTP clock driver. There are no active users in the
kernel.
The option was device driver dependent. If set, but without hardware
support, the correct behavior is to return zero in the relevant field
in the SCM_TIMESTAMPING ancillary message. Without device drivers
implementing the option, this field is effectively always zero.
Remove the internal plumbing to dissuage new drivers from implementing
the feature. Keep the SOF_TIMESTAMPING_SYS_HARDWARE flag, however, to
avoid breaking existing applications that request the timestamp.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No device driver will ever return an skb_shared_info structure with
syststamp non-zero, so remove the branch that tests for this and
optionally marks the packet timestamp as TP_STATUS_TS_SYS_HARDWARE.
Do not remove the definition TP_STATUS_TS_SYS_HARDWARE, as processes
may refer to it.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver explicitly clears a field that is unused and about to be
removed. Remove the initialization.
All fields in skb_shared_info before dataref are cleared in
__alloc_skb, so the removal is safe even while syststamp exists.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware timestamps can be exposed to userspace in raw hardware format
(hwtstamp) as well as converted to system time (syststamp). The second
variant is deprecated and only implemented by this driver.
The preferred method of hardware timestamp generation is to combine
hwtstamp with a device PTP clock. Octeon has its own PTP library
that relies on a shared memory interface to the PTP clock device.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A nice small set of bug fixes for arm-soc:
- two incorrect register addresses in DT files on shmobile and hisilicon
- one revert for a regression on omap
- one bug fix for a newly introduced pin controller binding
- one regression fix for the memory controller on omap
- one patch to avoid a harmless WARN_ON
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAU9fDBmCrR//JCVInAQIxCw/+IadEDDeP4WZHO0Bx9vm7Oj8XYlDg4xU8
O+SvqmJ3qDFNxbG7LEZ9B0dqcAaxkYPgF0LEy29uneQn+oKXykzRwhmXilB3akJR
Y/B3y7FJKch9dBZf+Kx+94NgHt1IdcaArWdSKBLgMN5/IZzRY3B8fo3AEjnHjt2P
c0kXasLOQ97aGiFobNHp5GLrR2uUjplzWjMDA7F9i6PQZ1grmDGJ2w67bZ8Uukwh
p2xYOmgHdyVRweFHrHlISNGWov8TPfGJpItM665ROMxJ+wREJ4rHp/VOA/74OMGf
heOEsUUhZOjEvNza8U4TCVroAqA26OCth8sd1mOOe+INPkt1IDAPK4zF0bxHt2it
PuxAVH43fyQ0oPerB9BfAwJOr+aSIQNYJRVpEDbwBU0d0/N/lERixPZxsmSDY4ES
cwzu9FTY2+tYfzS3WW/0fGDtIXXlEbcXnfxc3sSzjErV71GAq1UICxrBrUL5KoGY
YyBh4Ly6V6WzLC0dkRnYe+gEKIWn+SA95JGaYMYigQdIJHGKf7DoChWkDeWmrYwQ
cl34GZ5k79L6c2Az2YoON2R2vwByhP5kSZ5z6sNuyL0Z2TbRUeDw4qkjQcxFvfN0
NLqMidJhFZyKTjJtc0ttB+ah9kyZy+kyKoyKbIMDCk5zYTLAgh0PF85G0IJEEUU5
+qwzQP/ROjQ=
=Ny58
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A nice small set of bug fixes for arm-soc:
- two incorrect register addresses in DT files on shmobile and hisilicon
- one revert for a regression on omap
- one bug fix for a newly introduced pin controller binding
- one regression fix for the memory controller on omap
- one patch to avoid a harmless WARN_ON"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: Revert enabling of twl configuration for n900
ARM: dts: fix L2 address in Hi3620
ARM: OMAP2+: gpmc: fix gpmc_hwecc_bch_capable()
pinctrl: dra: dt-bindings: Fix pull enable/disable
ARM: shmobile: r8a7791: Fix SD2CKCR register address
ARM: OMAP2+: l2c: squelch warning dump on power control setting
Correctly assemble the client UUID by OR'ing in the flags rather than
assigning them over the other components.
Reported-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix kernel-doc warnings and function name in mm/page_alloc.c:
Warning(..//mm/page_alloc.c:6074): No description found for parameter 'pfn'
Warning(..//mm/page_alloc.c:6074): No description found for parameter 'mask'
Warning(..//mm/page_alloc.c:6074): Excess function parameter 'start_bitidx' description in 'get_pfnblock_flags_mask'
Warning(..//mm/page_alloc.c:6102): No description found for parameter 'pfn'
Warning(..//mm/page_alloc.c:6102): No description found for parameter 'mask'
Warning(..//mm/page_alloc.c:6102): Excess function parameter 'start_bitidx' description in 'set_pfnblock_flags_mask'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5XAH
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap n900 regression fix for v3.16 rc series" from Tony Lindgren:
Minimal regression fix for n900 display that got broken with
enabling of twl4030 PM features. Turns out more work is needed
before we can enable twl4030 PM on n900.
I did not notice this earlier as I have my n900 in a rack
and the display did not get enabled for device tree based booting
until for v3.16.
* tag 'omap-for-v3.16/n900-regression' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert enabling of twl configuration for n900
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration
for selected omaps) allowed n900 to cut off core voltages during
off-idle. This however caused a regression where twl regulator
vaux1 was not getting enabled for the LCD panel as we are not
requesting it for the panel.
Turns out quite a few devices on n900 are using vaux1, and we need
to either stop idling it, or add proper regulator_get calls for all
users. But until we have a proper solution implemented and tested,
let's just disable the twl off-idle configuration for now for n900.
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Fixes: 9188883fd6 (ARM: dts: Enable twl4030 off-idle configuration for selected omaps)
Signed-off-by: Tony Lindgren <tony@atomide.com>
In "Counting Packets Sent Between Arbitrary Internet Hosts", Jeffrey and
Jedidiah describe ways exploiting linux IP identifier generation to
infer whether two machines are exchanging packets.
With commit 73f156a6e8 ("inetpeer: get rid of ip_id_count"), we
changed IP id generation, but this does not really prevent this
side-channel technique.
This patch adds a random amount of perturbation so that IP identifiers
for a given destination [1] are no longer monotonically increasing after
an idle period.
Note that prandom_u32_max(1) returns 0, so if generator is used at most
once per jiffy, this patch inserts no hole in the ID suite and do not
increase collision probability.
This is jiffies based, so in the worst case (HZ=1000), the id can
rollover after ~65 seconds of idle time, which should be fine.
We also change the hash used in __ip_select_ident() to not only hash
on daddr, but also saddr and protocol, so that ICMP probes can not be
used to infer information for other protocols.
For IPv6, adds saddr into the hash as well, but not nexthdr.
If I ping the patched target, we can see ID are now hard to predict.
21:57:11.008086 IP (...)
A > target: ICMP echo request, seq 1, length 64
21:57:11.010752 IP (... id 2081 ...)
target > A: ICMP echo reply, seq 1, length 64
21:57:12.013133 IP (...)
A > target: ICMP echo request, seq 2, length 64
21:57:12.015737 IP (... id 3039 ...)
target > A: ICMP echo reply, seq 2, length 64
21:57:13.016580 IP (...)
A > target: ICMP echo request, seq 3, length 64
21:57:13.019251 IP (... id 3437 ...)
target > A: ICMP echo reply, seq 3, length 64
[1] TCP sessions uses a per flow ID generator not changed by this patch.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jeffrey Knockel <jeffk@cs.unm.edu>
Reported-by: Jedidiah R. Crandall <crandall@cs.unm.edu>
Cc: Willy Tarreau <w@1wt.eu>
Cc: Hannes Frederic Sowa <hannes@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per comment from David Miller, we try to make the buffer reassembly
function more resilient to user errors than it is today.
- We check that the "*buf" parameter always is set, since this is
mandatory input.
- We ensure that *buf->next always is set to NULL before linking in
the buffer, instead of relying of the caller to have done this.
- We ensure that the "tail" pointer in the head buffer's control
block is initialized to NULL when the first fragment arrives.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndm_type means L3 address type, in neighbour proxy and vxlan, it's RTN_UNICAST.
NDA_DST is for netlink TLV type, hence it's not right value in this context.
Signed-off-by: Jun Zhao <mypopydev@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-07-25
Please pull this batch of updates intended for the 3.17 stream!
For the mac80211 bits, Johannes says:
"We have a lot of TDLS patches, among them a fix that should make hwsim
tests happy again. The rest, this time, is mostly small fixes."
For the Bluetooth bits, Gustavo says:
"Some more patches for 3.17. The most important change here is the move of
the 6lowpan code to net/6lowpan. It has been agreed with Davem that this
change will go through the bluetooth tree. The rest are mostly clean up and
fixes."
and,
"Here follows some more patches for 3.17. These are mostly fixes to what
we've sent to you before for next merge window."
For the iwlwifi bits, Emmanuel says:
"I have the usual amount of BT Coex stuff. Arik continues to work
on TDLS and Ariej contributes a few things for HS2.0. I added a few
more things to the firmware debugging infrastructure. Eran fixes a
small bug - pretty normal content."
And for the Atheros bits, Kalle says:
"For ath6kl me and Jessica added support for ar6004 hw3.0, our latest
version of ar6004.
For ath10k Janusz added a printout so that it's easier to check what
ath10k kconfig options are enabled. He also added a debugfs file to
configure maximum amsdu and ampdu values. Also we had few fixes as
usual."
On top of that is the usual large batch of various driver updates --
brcmfmac, mwifiex, the TI drivers, and wil6210 all get some action.
Rafał has also been very busy with b43 and related updates.
Also, I pulled the wireless tree into this in order to resolve a
merge conflict...
P.S. The change to fs/compat_ioctl.c reflects a name change in a
Bluetooth header file...
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The sunvnet driver doesn't check whether or not a port is connected when
transmitting packets, which results in failures if a port fails to connect
(e.g., due to a version mismatch). The original code also assumes
unnecessarily that the first port is up and a switch, even though there is
a flag for switch ports.
This patch only matches a port if it is connected, and otherwise uses the
switch_port flag to send the packet to a switch port that is up.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This test is reversed so the memory is always leaked. It's better style
to remove the test anyway.
Fixes: 3e403a7777 ('bonding: make it possible to have unlimited nested upper vlans')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change formal parameter name to not shadow the global jiffies.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlPSBz0ACgkQjTAFq1RaXHPuwACfRPsgJi0EfpHAzPBkTlAR8Agw
MREAn3eKn1vdj5q55Y43mMkTZErHPr43
=jmRy
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-3.16-20140725' of git://gitorious.org/linux-can/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2014-07-25
this is a pull request of one patch for the net tree, hoping to get into the
3.16 release.
The patch by George Cherian fixes a regression in the c_can platform driver.
When using two interfaces the regression leads to a non function second
interface.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-07-25
This series contains updates to e1000e, ixgbe and ixgbevf.
Mark provides all the changes for ixgbe and ixgbevf. Converts some udelay()
calls to the preferred usleep_range(). Fixes a spurious release of the
semaphore in several functions when there was a failure to acquire the
semaphore in the first place. Fixes a X540 semaphore error where an
incorrect check was treating success as failure and vice-versa. Fixed
ixgbe_write_mbx() error when it was being called and there was no
mbx->ops.write method defined, so no error code was returned. The
corresponding read function would explicitly return an error in such a
case as do other functions. Cleans up unused (dead) code by removing it.
Finally make return values more direct, eliminating some gotos and
otherwise unneeded conditionals, which allows the removal of some local
variables.
David provides all the changes for e1000e. Fix CRC errors with jumbo
traffic for 82579, i217 and i218 client parts to increase the gap
between the read and write pointers in the transmit FIFO. Added code
to check and respond to previously ignored return values from NVM
access functions. Added support for EEE in Sx states and fixed EEE in
S5 with runtime PM enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull ARM AES crypto fixes from Herbert Xu:
"This push fixes a regression on ARM where odd-sized blocks supplied to
AES may cause crashes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: arm-aes - fix encryption of unaligned data
crypto: arm64-aes - fix encryption of unaligned data
Pull powerpc fixes from Ben Herrenschmidt:
"Here are 3 more small powerpc fixes that should still go into .16.
One is a recent regression (MMCR2 business), the other is a trivial
endian fix without which FW updates won't work on LE in IBM machines,
and the 3rd one turns a BUG_ON into a WARN_ON which is definitely a
LOT more friendly especially when the whole thing is about retrieving
error logs ..."
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Fix endianness of flash_block_list in rtas_flash
powerpc/powernv: Change BUG_ON to WARN_ON in elog code
powerpc/perf: Fix MMCR2 handling for EBB
Fix the same alignment bug as in arm64 - we need to pass residue
unprocessed bytes as the last argument to blkcipher_walk_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org # 3.13+
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
cryptsetup fails on arm64 when using kernel encryption via AF_ALG socket.
See https://bugzilla.redhat.com/show_bug.cgi?id=1122937
The bug is caused by incorrect handling of unaligned data in
arch/arm64/crypto/aes-glue.c. Cryptsetup creates a buffer that is aligned
on 8 bytes, but not on 16 bytes. It opens AF_ALG socket and uses the
socket to encrypt data in the buffer. The arm64 crypto accelerator causes
data corruption or crashes in the scatterwalk_pagedone.
This patch fixes the bug by passing the residue bytes that were not
processed as the last parameter to blkcipher_walk_done.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Nikolay Aleksandrov says:
====================
inet: frag: cleanup and update
The end goal of this patchset is to remove the LRU list and to move the
frag eviction to a work queue. It also does a couple of necessary cleanups
and fixes. Brief patch descriptions:
Patches 1 - 3 inclusive: necessary clean ups
Patch 4 moves the eviction from the softirqs to a workqueue.
Patch 5 removes the nqueues counter which was protected by the LRU lock
Patch 6 removes the, by now unused, lru list.
Patch 7 moves the rebuild timer to the workqueue and schedules the rebuilds
only if we've hit the maximum queue length on some of the chains.
Patch 8 migrate the rwlock to a seqlock since the rehash is usually a rare
operation.
Patch 9 introduces an artificial global memory limit based on the value of
init_net's high_thresh which is used to cap the high_thresh of the
other namespaces. Also introduces some sane limits on the other
tunables, and makes it impossible to have low_thresh > high_thresh.
Here are some numbers from running netperf before and after the patchset:
Each test consists of the following setting: -I 95,5 -i 15,10
1. Bound test (-T 4,4)
1.1 Virtio before the patchset -
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.122.177 () port 0 AF_INET : +/-2.500% @ 95% conf. : cpu bind
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
212992 64000 30.00 722177 0 12325.1 34.55 2.025
212992 30.00 368020 6280.9 34.05 0.752
1.2 Virtio after the patchset -
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.122.177 () port 0 AF_INET : +/-2.500% @ 95% conf. : cpu bind
Socket Message Elapsed Messages CPU Service
Size Size Time Okay Errors Throughput Util Demand
bytes bytes secs # # 10^6bits/sec % SS us/KB
212992 64000 30.00 727030 0 12407.9 35.45 1.876
212992 30.00 505405 8625.5 34.92 0.693
2. Virtio unbound test
2.1 Before the patchset
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.122.177 () port 0 AF_INET : +/-2.500% @ 95% conf.
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 64000 30.00 730008 0 12458.77
212992 30.00 416721 7112.02
2.2 After the patchset
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.122.177 () port 0 AF_INET : +/-2.500% @ 95% conf.
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 64000 30.00 731129 0 12477.89
212992 30.00 487707 8323.50
3. 10 gig unbound tests
3.1 Before the patchset
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.133.1 () port 0 AF_INET : +/-2.500% @ 95% conf.
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 64000 30.00 417209 0 7120.33
212992 30.00 416740 7112.33
3.2 After the patchset
MIGRATED UDP STREAM TEST from 0.0.0.0 (0.0.0.0) port 0 AF_INET to 192.168.133.1 () port 0 AF_INET : +/-2.500% @ 95% conf.
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
212992 64000 30.00 438009 0 7475.33
212992 30.00 437630 7468.87
Given the options each netperf ran between 10 and 15 times for 30 seconds
to get the necessary confidence, also the tests themselves ran 3 times and
were consistent.
Another set of tests that I ran were parallel stress tests which consisted
of flooding the machine with fragmented packets from different sources with
frag timeout set to 0 (so there're lots of timeouts) and low_thresh set to
1 byte (so evictions are happening all the time) and on top of that running
a namespace create/destroy endless loop with network interfaces and
addresses that got flooded (for the brief periods they were up) in parallel.
This test ran for an hour without any issues.
====================
This patch makes init_net's high_thresh limit to be the maximum for all
namespaces, thus introducing a global memory limit threshold equal to the
sum of the individual high_thresh limits which are capped.
It also introduces some sane minimums for low_thresh as it shouldn't be
able to drop below 0 (or > high_thresh in the unsigned case), and
overall low_thresh should not ever be above high_thresh, so we make the
following relations for a namespace:
init_net:
high_thresh - max(not capped), min(init_net low_thresh)
low_thresh - max(init_net high_thresh), min (0)
all other namespaces:
high_thresh = max(init_net high_thresh), min(namespace's low_thresh)
low_thresh = max(namespace's high_thresh), min(0)
The major issue with having low_thresh > high_thresh is that we'll
schedule eviction but never evict anything and thus rely only on the
timers.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rehash is rare operation, don't force readers to take
the read-side rwlock.
Instead, we only have to detect the (rare) case where
the secret was altered while we are trying to insert
a new inetfrag queue into the table.
If it was changed, drop the bucket lock and recompute
the hash to get the 'new' chain bucket that we have to
insert into.
Joint work with Nikolay Aleksandrov.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
merge functionality into the eviction workqueue.
Instead of rebuilding every n seconds, take advantage of the upper
hash chain length limit.
If we hit it, mark table for rebuild and schedule workqueue.
To prevent frequent rebuilds when we're completely overloaded,
don't rebuild more than once every 5 seconds.
ipfrag_secret_interval sysctl is now obsolete and has been marked as
deprecated, it still can be changed so scripts won't be broken but it
won't have any effect. A comment is left above each unused secret_timer
variable to avoid confusion.
Joint work with Nikolay Aleksandrov.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'nqueues' counter is protected by the lru list lock,
once thats removed this needs to be converted to atomic
counter. Given this isn't used for anything except for
reporting it to userspace via /proc, just remove it.
We still report the memory currently used by fragment
reassembly queues.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the high_thresh limit is reached we try to toss the 'oldest'
incomplete fragment queues until memory limits are below the low_thresh
value. This happens in softirq/packet processing context.
This has two drawbacks:
1) processors might evict a queue that was about to be completed
by another cpu, because they will compete wrt. resource usage and
resource reclaim.
2) LRU list maintenance is expensive.
But when constantly overloaded, even the 'least recently used' element is
recent, so removing 'lru' queue first is not 'fairer' than removing any
other fragment queue.
This moves eviction out of the fast path:
When the low threshold is reached, a work queue is scheduled
which then iterates over the table and removes the queues that exceed
the memory limits of the namespace. It sets a new flag called
INET_FRAG_EVICTED on the evicted queues so the proper counters will get
incremented when the queue is forcefully expired.
When the high threshold is reached, no more fragment queues are
created until we're below the limit again.
The LRU list is now unused and will be removed in a followup patch.
Joint work with Nikolay Aleksandrov.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First step to move eviction handling into a work queue.
We lose two spots that accounted evicted fragments in MIB counters.
Accounting will be restored since the upcoming work-queue evictor
invokes the frag queue timer callbacks instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
hide actual hash size from individual users: The _find
function will now fold the given hash value into the required range.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function rtas_flash_firmware passes the address of a data structure,
flash_block_list, when making the update-flash-64-and-reboot rtas call.
While the endianness of the address is handled correctly, the endianness
of the data is not. This patch ensures that the data in flash_block_list
is big endian when passed to rtas on little endian hosts.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
