We already have the code to calculate the WRPLL output clock from
the register values, but for some reason we're only using it for
HDMI and not DP. Throw out the inflexible DP DPLL table lookup and
just call the HDMI code which decodes the actual register values.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190207173230.22368-12-ville.syrjala@linux.intel.com
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
This exactly same approach was already used from gen9
to gen10 and from gen10 to gen11. Let's also use it
for gen11+.
Let's first assume that we inherit a similar platform
and than we apply the differences on top.
Different from the previous attempts this will be
done this time with coccinelle. We obviously need to
exclude some case that is really exclusive for gen11
like PCH, Firmware, and few others. Luckly this was
easy to filter by selecting the files we are touching
with coccinelle as exposed below:
spatch -sp_file gen11\+.cocci --in-place i915_perf.c \
intel_bios.c intel_cdclk.c intel_ddi.c \
intel_device_info.c intel_display.c intel_dpll_mgr.c \
intel_dsi_vbt.c intel_hdmi.c intel_mocs.c intel_color.c
@noticelake@ expression e; @@
-!IS_ICELAKE(e)
+INTEL_GEN(e) < 11
@notgen11@ expression e; @@
-!IS_GEN(e, 11)
+INTEL_GEN(e) < 11
@icelake@ expression e; @@
-IS_ICELAKE(e)
+INTEL_GEN(e) >= 11
@gen11@ expression e; @@
-IS_GEN(e, 11)
+INTEL_GEN(e) >= 11
No functional change.
v2: Remove intel_lrc.c per Tvrtko request since those were w/a
for ICL hw issuea and media related configuration.
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190308214300.25057-1-rodrigo.vivi@intel.com
Define a HAS_TRANSCODER_EDP() macro that checks if we have defined an
offset for this transcoder. This allows platforms to be defined without
eDP transcoder.
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190222230254.20351-2-lucas.demarchi@intel.com
With fastboot enabled in gen9+ it broke the HDMI reset as just
setting mode_changed to true causes a fastset and here we want a full
modeset that will disable and then enable the encoder of this HDMI
link actually, so setting connectors_changed instead that will cause
modeset as desired.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190302003349.19189-3-jose.souza@intel.com
drm_atomic_commit() call chain already takes care of adding
connectors and planes, so lets no add then manually if not changing
their states.
drm_atomic_commit()
drm_atomic_check_only()
config->funcs->atomic_check()/intel_atomic_check()
drm_atomic_helper_check()
drm_atomic_helper_check_modeset()
for_each_oldnew_crtc_in_state()
drm_atomic_add_affected_connectors()
drm_atomic_add_affected_planes()
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190302003349.19189-2-jose.souza@intel.com
Atomic state needs to be put even if the commit was successful.
Fixes: dba14b27dd ("drm/i915: Reinitialize sink scrambling/TMDS clock ratio on HPD")
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190302003349.19189-1-jose.souza@intel.com
Add code to read the infoframes from the video DIP and unpack them into
the crtc state.
v2: Make the read funcs return void (Daniel)
Drop the duplicate infoframe enabled checks (Daniel)
Add a FIXME for lspcon infoframe readout
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-6-ville.syrjala@linux.intel.com
Store the mask of enabled infoframes in the crtc state. We'll start
with just the readout for HDMI encoder, and we'll expand this
to compute the bitmask in .compute_config() later. SDVO will also
follow later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-4-ville.syrjala@linux.intel.com
We want to start tracking which infoframes are enabled, so let's replace
the boolean flag with a bitmask.
We'll abstract the bitmask so that it's not platform dependent. That
will allow us to examine the bitmask later in platform independent code.
v2: Don't map VIDEO_DIP_ENABLE to the null packet (Daniel)
Put a FIXME in the lspcon function
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190225174106.2163-3-ville.syrjala@linux.intel.com
The commit that this patch fixes changed the order of the parameters
of MG_DP_MODE() but din't update the callers, breaking type-c on ICL.
Fixes: 58106b7d81 ("drm/i915: Make MG PHY macros semantically consistent")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Aditya Swarup <aditya.swarup@intel.com>
Cc: Manasi navare <manasi.d.navare@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190222202437.6575-1-jose.souza@intel.com
Organize MG PHY macro definitions semantically based on dword, lane and
port (in this order).
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Manasi navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128220012.13122-3-aditya.swarup@intel.com
Organize combo PHY DDI macro definitions semantically based on dword,
lane and port (in this order).
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190128220012.13122-2-aditya.swarup@intel.com
Changing the i915_edp_psr_debug was enabling, disabling or switching
PSR version by directly calling intel_psr_disable_locked() and
intel_psr_enable_locked(), what is not the default PSR path that will
be executed by real users.
So lets force a fastset in the PSR CRTC to trigger a pipe update and
stress the default code path.
Recently a bug was found when switching from PSR2 to PSR1 while
enable_psr kernel parameter was set to the default parameter, this
changes fix it and also fixes the bug linked bellow were DRRS was
left enabled together with PSR when enabling PSR from debugfs.
v2: Handling missing case: disabled to PSR1
v3: Not duplicating the whole atomic state(Maarten)
v4: Adding back the missing call to intel_psr_irq_control(Dhinakaran)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108341
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190206211845.5322-1-jose.souza@intel.com
The downgrade of the fullmodeset into fastset
intel_encoder->update_pipe, in possible scenario, skips the En/Dis-able
DDI. Hence breaks the HDCP state change handling.
We also don't have any hdcp tests in CI, because the shard runs don't
have hdcp capable outputs :-/
So this change fixs it by handling the HDCP state change request at
intel_encoder->update_pipe too along with enable and disable of the DDI.
Fixes: d19f958db2 ("drm/i915: Enable fastset for non-boot modesets.")
v2:
Added commit id that broke the HDCP [Daniel]
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
cc: Hans de Goede <hdegoede@redhat.com>
cc: Daniel Vetter <daniel.vetter@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1549295080-18353-1-git-send-email-ramalingam.c@intel.com
We should not pass DPLL_ID_ICL_DPLL0 or DPLL_ID_ICL_DPLL1 to this
function because the path is only taken for non-combophy ports. Let the
warning trigger if improper value is given.
While at it, rename the function to match the register name we are
trying to program.
v2: fix typo in comment
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125222444.19926-4-lucas.demarchi@intel.com
Even if we don't have the correct clock and get a warning, we should not
skip the return.
v2: improve commit message (from Joonas)
Fixes: 1fa11ee2d9 ("drm/i915/icl: start adding the TBT pll")
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: <stable@vger.kernel.org> # v4.19+
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125222444.19926-3-lucas.demarchi@intel.com
Fix the TODO leftover in the code by changing the argument in MG_PLL
macros. The MG_PLL ids used to access the register values can be
converted from tc_port rather than port.
All these registers can use the TC port to calculate the right offsets
because they are only available for TC ports. The range (PORT_C onwards)
may not be stable and change from platform to platform. So by using the
TC id directly we avoid having to check for the platform in the "leaf
functions" and thus passing dev_priv around.
The helper functions were also renamed to use "tc" as prefix to make
them more generic.
v2: Improve commit message and fix checkpatch warning (from Paulo)
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190125222444.19926-2-lucas.demarchi@intel.com
Restore our saved values for backlight. This way even with fastset on
S4 resume we will correctly restore the backlight to the active values.
Changes since v1:
- Call enable_backlight() when backlight.level is set. On suspend
backlight.enabled is always cleared, this makes it not a good
indicator. Also check for crtc->state->active.
Changes since v2:
- Use the new update_pipe() callback to run this on resume as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tolga Cakir <cevelnet@gmail.com>
Cc: Basil Eric Rabi <ericbasil.rabi@gmail.com>
Cc: Hans de Goede <jwrdegoede@fedoraproject.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108160842.13396-1-maarten.lankhorst@linux.intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-4-jani.nikula@intel.com
Something that I completely missed when implementing the new MST VCPI
atomic helpers is that with those helpers, there's technically a chance
of us having to grab additional modeset locks in ->compute_config() and
furthermore, that means we have the potential to hit a normal modeset
deadlock. However, because ->compute_config() only returns a bool this
means we can't return -EDEADLK when we need to drop locks and try again
which means we end up just failing the atomic check permanently. Whoops.
So, fix this by modifying ->compute_config() to pass down an actual
error code instead of a bool so that the atomic check can be restarted
on modeset deadlocks.
Thanks to Ville Syrjälä for pointing this out!
Changes since v1:
* Add some newlines
* Return only -EINVAL from hsw_crt_compute_config()
* Propogate return code from intel_dp_compute_dsc_params()
* Change all of the intel_dp_compute_link_config*() variants
* Don't miss if (hdmi_port_clock_valid()) branch in
intel_hdmi_compute_config()
[Cherry-picked from drm-misc-next to drm-intel-next-queued to fix
linux-next & drm-tip conflict, while waiting for proper propagation of
the DP MST series that this commit fixes. In hindsight, a topic branch
might have been a better approach for it.]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: eceae14724 ("drm/dp_mst: Start tracking per-port VCPI allocations")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109320
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190115200800.3121-1-lyude@redhat.com
(cherry picked from commit 96550555a7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
The majority of runtime-pm operations are bounded and scoped within a
function; these are easy to verify that the wakeref are handled
correctly. We can employ the compiler to help us, and reduce the number
of wakerefs tracked when debugging, by passing around cookies provided
by the various rpm_get functions to their rpm_put counterpart. This
makes the pairing explicit, and given the required wakeref cookie the
compiler can verify that we pass an initialised value to the rpm_put
(quite handy for double checking error paths).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-16-chris@chris-wilson.co.uk
Call intel_psr_enable() and intel_edp_drrs_enable() on pipe updates to make
sure that we enable PSR / DRRS (when applicable) on fastsets.
Note calling these functions when PSR / DRRS has already been enabled is a
no-op, so it is safe to do this on every encoder->update_pipe callback.
Changes in v2:
-Merge the patches adding the intel_psr_enable() and intel_edp_drrs_enable()
calls into a single patch
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220132120.15318-3-hdegoede@redhat.com
Atm HPD disconnect events on TypeC ports will break things, since we'll
switch the TypeC mode (between legacy and disconnected modes as well as
among USB DP alternate, Thunderbolt alternate and disconnected modes) on
the fly from the HPD disconnect interrupt work while the port may be
still active.
Even if the port happens to be not active during the disconnect we'd
still have a problem during a subsequent modeset or AUX transfer that
could happen regardless of the port's connected state. For instance the
system resume display mode restore code and userspace could perform a
modeset on the port or userspace could start an AUX transfer even if the
port is in disconnected state.
To fix this keep TypeC legacy ports in legacy mode whenever we're not
suspended. This mode is a static configuration as opposed to the
Thunderbolt and USB DP alternate modes between which we can switch
dynamically.
We determine if a TypeC port is legacy (wired to a legacy HDMI or a
legacy DP connector) via the VBT DDI port specific USB-TypeC and
Thunderbolt flags. If both these flags are cleared then the port is
configured for legacy mode.
On such legacy ports we'll run the TypeC PHY connect sequence explicitly
during driver loading and system resume (vs. running the sequence during
HPD processing). The connect will succeed even if the display is not
connected to begin with (or disappears during the suspended state) since
for legacy ports the PORT_TX_DFLEXDPPMS / DP_PHY_MODE_STATUS_COMPLETED
flag is always set (as opposed to the USB DP alternate mode where it
gets set only when a display is connected).
Correspondingly run the TypeC PHY disconnect sequence during system
suspend and driver unloading. For the unloading case I had to split
up intel_dp_encoder_destroy() to be able to have the 1. flush any
pending encoder work, 2. disconnect TC PHY, 3. call DRM core cleanup and
kfree on the encoder object.
For now run the PHY disconnect during suspend only for TypeC legacy
ports. We will need to disconnect even in USB DP alternate mode in the
future, but atm we don't have a way to reconnect the port in this mode
during resume if the display disappears while being suspended. So for
now punt on this case.
Note that we do not disconnect the port during runtime suspend; in
legacy mode there are no shared HW resources (PHY lanes) with other HW
blocks (USB), so no need to release / reacquire these resources as with
USB DP alternate mode. The only reason to disconnect legacy ports during
system suspend is that the PORT_TX_DFLEXDPPMS /
DP_PHY_MODE_STATUS_COMPLETED flag must be rechecked and the port must be
connected again during system resume. We'll also have to turn the check
for this flag into a poll, after figuring out what's the proper timeout
value for it.
v2:
- Remove the redundant special casing of legacy mode when doing a
disconnect in icl_tc_port_connected(). It's guaranteed already that we
won't disconnect legacy ports in that function.
- Add a note about the new intel_ddi_encoder_destroy() hook.
- Reword the commit message after switching to the VBT based detection.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108070
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108924
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-4-imre.deak@intel.com
In August 2018 the BSPEC changed the ICL port programming sequence to
closely resemble earlier gen programming sequence. Restrict combo phy to
HBR max rate unless eDP panel is connected to port.
v2: remove debug code that Imre found
v3: simplify translation table if-else
v4: edp translation table now based on link rate and low_swing
v5: Misc review comments + r-b
BSpec: 21257
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1545084827-5776-1-git-send-email-clinton.a.taylor@intel.com
This patch implements the functionality for getting PIPE configuration
to which DSI encoder is connected. Use the same method to get port clock
like other DDI encoders. Used during the atomic modeset.
v2 by Jani:
- Squash Madhav's and Vandita's get config bits together
- Move cnl_calc_wrpll_link() to intel_drv.h
- Drop extra temp variables
- Use enc_to_intel_dsi() instead of open coding
Co-developed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f21fa4258068d04582f2bf30735e5536a8043bdf.1543500286.git.jani.nikula@intel.com
The requirement for the DDI port clock gating for a port in DSI mode is
the opposite wrt. the case when the port is in DDI mode: the clock
should be gated when the port is active and ungated when the port is
inactive. Note that we cannot simply keep the DDI clock gated when the
port will be only used in DSI mode: it must be gated/ungated at a
specific spot in the DSI enable/disable sequence.
Ensure the above for all ports of a DSI encoder, also adding a sanity
check that we haven't registered another encoder using the same port
(VBT should never allow this to happen).
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ceb14d5a68e8e23988d923d4290a4f981789e616.1543500285.git.jani.nikula@intel.com
Unclutter the haswell_crtc_enable() and haswell_crtc_disable() functions
a bit by moving the pll to port mapping and unmapping functions to the
ddi encoder hooks. This allows removal of a bunch of boilerplate code
from the functions.
Additionally, the ICL DSI encoder needs to do the clock gating and
ungating slightly differently, and this allows its own handling in a
clean fashion.
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f8e2982ceea4c05dc254a0c15e2b3be1d5f271d3.1543500285.git.jani.nikula@intel.com
Set the suitable bits in DP_TP_CTL to stop
bit correction when DSC is disabled.
v2:
- rebased.
- Add additional check for compression state. (Gaurav)
v3: rebased.
v4:
- Move the code to the proper spot according to spec (Ville)
- Use proper checks (manasi)
v5: Remove unnecessary checks (Ville)
v6: Resolve warnings. Add crtc_state as an argument to
intel_disable_ddi_buf(). (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-17-manasi.d.navare@intel.com
If FEC is supported, the corresponding
DP_TP_CTL register bits have to be configured.
The driver has to program the FEC_ENABLE in DP_TP_CTL[30] register
and wait till FEC_STATUS in DP_TP_CTL[28] is 1.
Also add the warn message to make sure that the control
register is already active while enabling FEC.
v2:
- Change commit message. Configure fec state after
link training (Manasi, Gaurav)
- Remove redundent checks (Manasi)
- Remove the registers that get added automagically (Anusha)
v3: s/intel_dp_set_fec_state()/intel_dp_enable_fec_state() (Gaurav)
v4: rebased.
v5:
- Move the code to the proper spot, according to spec.(Ville)
- Use fec state as a check too.
v6: Pass intel_encoder, instead of intel_dp. (Ville)
v7: Remove unwanted comments (Manasi)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-16-manasi.d.navare@intel.com
If the panel supports FEC, the driver has to
set the FEC_READY bit in the dpcd register:
FEC_CONFIGURATION.
This has to happen before link training.
v2: s/intel_dp_set_fec_ready/intel_dp_sink_set_fec_ready
- change commit message. (Gaurav)
v3: rebased. (r-b Manasi)
v4: Use fec crtc state, before setting FEC_READY
bit. (Anusha)
v5: Move to intel_ddi.c
- Make the function static (Anusha)
v6: Dont pass state as a separate argument (Ville)
v7: (From Manasi)
* Correct the debug print (Ville)
Cc: dri-devel@lists.freedesktop.org
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-15-manasi.d.navare@intel.com
A separate power well 2 (PG2) is required for VDSC on eDP transcoder
whereas all other transcoders use the power wells associated with the
transcoders for VDSC.
This patch adds a helper to obtain correct power domain depending on
transcoder being used and enables/disables the power wells during
VDSC enabling/disabling.
v4:
* Get VDSC power domain only if compression en is set
in crtc_state (Ville, Imre)
v3:
* Call it intel_dsc_power_domain, add to
intel_ddi_get_power_domains (Ville)
v2:
* Fix tabs, const crtc_state, fix comments (Ville)
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-13-manasi.d.navare@intel.com
After encoder->pre_enable() hook, after link training sequence is
completed, PPS registers for DSC encoder are configured using the
DSC state parameters in intel_crtc_state as part of DSC enabling
routine in the source. DSC enabling routine is called after
encoder->pre_enable() before enbaling the pipe and after
compression is enabled on the sink.
v7:
* Remove unnecessary comments, leftovers (Ville)
* No need for explicit val &= ~ (Ville)
v6:
intel_dsc_enable to be part of pre_enable hook (Ville)
v5:
* make crtc_state const (Ville)
v4:
* Use cpu_transcoder instead of encoder->type for using EDP transcoder
DSC registers(Ville)
* Keep all PSS regs together (Anusha)
v3:
* Configure Pic_width/2 for each VDSC engine when two VDSC engines per pipe
are used (Manasi)
* Add DSC slice_row_per_frame in PPS16 (Manasi)
v2:
* Enable PG2 power well for VDSC on eDP
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
[manasi: fixup the line longer than 100 chars while applying]
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-8-manasi.d.navare@intel.com
This patch enables decompression support in sink device
before link training and disables the same during the
DDI disabling.
v3 (From manasi):
* Pass bool state to enable/disable (Ville)
v2:(From Manasi)
* Change the enable/disable function to take crtc_state
instead of intel_dp as an argument (Manasi)
* Use the compression_enable flag as part of crtc_state (Manasi)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128202628.20238-6-manasi.d.navare@intel.com
Depending on the transcoder enum values to translate from transcoder to
the corresponding CHICKEN_TRANS register can easily break if we add a
new transcoder. Add an explicit mapping instead, by using helpers to
look up the register instance either by transcoder or port (since
unconveniently the registers have both port and transcoder specific
bits).
While at it also check for the correctness of GEN, port, transcoder. I
wasn't sure if psr2_enabled can only be set for GEN9+, but that seems to
be the case indeed (see setting of sink_psr2_support in
intel_psr_init_dpcd()).
v2 (Ville):
- Make gen9_chicken_trans_reg() internal to intel_psr.c.
- s/trans/cpu_transcoder/
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181119180021.370-1-imre.deak@intel.com
We shouldn't consider an encoder inactive if it doesn't have a CRTC
linked, but has virtual MST encoders with a crtc linked. Fix this.
Also we should not sanitize the mapping for MST encoders, as it's always
their primary encoder (which could be even in SST mode) whose active
state determines if we need the clock being enabled for the
corresponding physical port. Fix this too.
This fixes at least an existing breakage where we incorrectly disabled
the clock for an active DP encoder when sanitizing its MST virtual
encoders. Not sure if there are BIOSes that enable an output in MST
mode, but our HW readout is mostly missing for it anyway, so just warn
for that case.
Fixes: 70332ac539 ("drm/i915/icl+: Sanitize port to PLL mapping")
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reported-by: Antonio Argenziano <antonio.argenziano@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107200836.10191-2-imre.deak@intel.com
Check for reserved register field values and conflicting
transcoder->port mappings (both MST and non-MST mappings or multiple SST
mappings).
This is also needed for the next patch to determine if a port is in MST
mode during sanitization after HW readout.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Antonio Argenziano <antonio.argenziano@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181107200836.10191-1-imre.deak@intel.com
The MG DP mode needs to be configured for Type C static/fixed/legacy
HDMI ports too, the same way as it's configured for Type C
static/fixed/legacy, fix this.
Bspec: 4232, 21735
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102192656.4472-3-imre.deak@intel.com
The MG PHY clock gating needs to be configured for Type C
static/fixed/legacy HDMI ports the same way it's configured for Type C
static/fixed/legacy and aternate mode DP ports, fix this.
Bspec: 4232, 21735
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Tested-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181102192656.4472-2-imre.deak@intel.com
BIOS can leave the PLL to port mapping enabled, even if the
corresponding encoder is disabled. Disable the port mapping in this
case.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-9-imre.deak@intel.com
DDI/TypeC ports need the AUX power domain for main link functionality
even when they operate in HDMI static mode, so enable the power domain
for these ports too.
v4:
- Rebase on the upstream ICL pre_pll_enable change.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-7-imre.deak@intel.com
For DDI/TypeC ports the AUX power domain needs to be enabled before the
port's PLL is enabled, so move the enabling earlier accordingly.
v2:
- Preserve the pre_pll hook for GEN9_LP. (Ville)
v3:
- Add related BSpec entries to commit log. (Jose)
v4:
- Rebase on the upstream ICL pre_pll_enable change.
BSpec: 21750, 22243
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-6-imre.deak@intel.com
From ICL onwards the AUX power domain may change dynamically based on
whether a DDI/TypeC port is in thunderbolt or non-thunderbolt mode, so
use a helper function instead of a static field to get the current
domain.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-5-imre.deak@intel.com
From ICL onwards DDI/TypeC ports - even in HDMI static mode - need to know
which AUX CH belongs to them, so initialize aux_ch for those ports too.
For consistency do this for all HDMI ports, not only for DDI/TypeC ones.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-4-imre.deak@intel.com
From ICL onwards all DDI/TypeC ports - even working in HDMI mode - need
to know their corresponding AUX CH, so move the field to a common
struct.
No functional change.
v3:
- Add code comment about which ports aux_ch is used for. (Jose)
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181101140427.31026-3-imre.deak@intel.com
In case of Legacy DP connector on TypeC port, the
flex IO DPMLE register is set to number of lanes configured
by the display driver which will be programmed into DDI_BUF_CTL
PORT_WIDTH_SELECTION.
This needs to be programmed before enabling the shared PLLs hence
add a pre_pll_enable hook for ICL and add this programming in that hook.
v2:
* Remove the check for combophy port (Jose)
* Simplify the port reversal check logic (Jose)
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jose Roberto de Souza <jose.souza@intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Acked-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181023191248.26418-2-manasi.d.navare@intel.com
