Semantics of NR_IRQS is different on machines with SPARSE_IRQ option
disabled or enabled, in the latter case IRQs are allocated starting
at least from the value specified by NR_IRQS and going upwards, so
the check of (irq >= NR_IRQ) to decide about an error code returned by
platform_get_irq() is completely invalid, don't attempt to overrule
irq subsystem in the driver.
The change fixes lpc32xx_keys driver initialization on boot:
lpc32xx_keys 40050000.key: failed to get platform irq
lpc32xx_keys: probe of 40050000.key failed with error -22
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 700a38b27e ("Input: gpio_keys - switch to using generic device
properties") switched to use generic device properties for GPIO keys and
commit 5feeca3c1e ("Input: gpio_keys - add support for GPIO descriptors")
switched from legacy GPIO numbers to GPIO descriptors.
Previously devm_gpio_request_one was explicitly passed GPIOF_DIR_IN flag
to set the GPIO direction as input. However devm_get_gpiod_from_child
doesn't have such provisions and hence fwnode_get_named_gpiod can't set
it as input.
This breaks few platforms with the following error:
" gpiochip_lock_as_irq: tried to flag a GPIO set as output for IRQ
unable to lock HW IRQ <n> for IRQ
genirq: Failed to request resources for POWER (irq <x>) on irqchip
gpio_keys: Unable to claim irq <x>; error -22
gpio-keys: probe failed with error -22 "
This patch fixes the issue by setting input direction explicitly for
gpio lines described by generic properties.
Fixes: 700a38b27e ("Input: gpio_keys - switch to using generic device properties")
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make use of the device property API in this driver so that both OF based
systems and ACPI based systems can use this driver.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GPIO descriptors are the preferred way over legacy GPIO numbers
nowadays. Convert the driver to use GPIO descriptors internally but
still allow passing legacy GPIO numbers from platform data to support
existing platforms.
Based on commits 633a21d80b ("input: gpio_keys_polled: Add support
for GPIO descriptors") and 1ae5ddb6f8 ("Input: gpio_keys_polled -
request GPIO pin as input.").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
for_each_available_child_of_node(node, pp) takes reference to 'pp' and
drops it when attempting next iteration. However if we exit the loop early
we need to drop the reference ourselves.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of using #ifdef, let's mark suspend and resume methods as
__maybe_unused to provide better compile coverage.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It does not matter if given GPIO may sleep or not when reading state,
polling is always done in a non-atomic context, so we should always
be able to simply use gpiod_get_value_cansleep().
Also let's note in the logs when we fail to read gpio state.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 633a21d80b ("input: gpio_keys_polled: Add support for GPIO
descriptors") placed gpio descriptor into gpio_keys_button structure, which
is supposed to be part of platform data and not modifiable by the driver.
To keep the data constant, let's move the descriptor to
gpio_keys_button_data structure instead.
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Older versions of gcc warn about the tca8418_irq_handler function
as they can't keep track of the variable assignment inside of the
loop when using the -Wmaybe-unintialized flag:
drivers/input/keyboard/tca8418_keypad.c: In function ‘tca8418_irq_handler’:
drivers/input/keyboard/tca8418_keypad.c:172:9: error: ‘reg’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/input/keyboard/tca8418_keypad.c:165:5: note: ‘reg’ was declared here
This is fixed in gcc-6, but it's possible to rearrange the code
in a way that avoids the warning on older compilers as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Trivial fix to typo in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into next
Sync up with mainline to bring in I2C host notify changes and other
updates.
Pull input subsystem updates from Dmitry Torokhov:
"You will get
- a new driver for Elan eKTF2127 touchscreen controllers
- a new "gpio-decoder" driver to read and report state of several
GPIO lines
- an ADC resistor ladder driver
- the ft6326 driver is removed because edt-ft5x06 handles the same
devices just fine.
.. plus the regular slew of driver fixes/enhancements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (26 commits)
Input: elan_i2c - fix return tests of i2c_smbus_read_block_data()
Input: ektf2127 - mark PM functions as __maybe_unused
Input: snvs_pwrkey - drop input_free_device call if input_register_device fails
Input: add support for Elan eKTF2127 touchscreen controller
Input: serio - add hangup support
Input: tps65218-pwrbutton - add support for tps65217 variant
Input: jornada720_ts - get rid of mach/irqs.h and mach/hardware.h includes
Input: jornada720_kbd - remove unneeded mach/hardware.h include
Input: focaltech - mark focaltech_set_resolution() static
Input: wdt87xx_i2c - fix the flash erase issue
Input: gpio-keys-polled - don't use unit-address with button nodes
Input: add generic input driver to read encoded GPIO lines
Input: add ADC resistor ladder driver
Input: pegasus_notetaker - directly include workqueue header
Input: elants_i2c - get product id on recovery mode for FW update
Input: wm97xx - remove deprecated create_singletheread_workqueue
Input: mc13783_ts - remove deprecated create_singletheread_workqueue
Input: psmouse - remove deprecated create_singletheread_workqueue
Input: jornada720_kbd - switch to using dev_dbg
Input: jornada720_kbd - get rid of mach/irqs.h include
...
- Add the MFD bindings doc to MAINTAINERS
- New Drivers
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
- New Device Support
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
- New Functionality
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
- Fix-ups
- Clean-up defunct author emails; da9063, max14577
- Kconfig fixups; wm8350-i2c, as3722
- Constify; altera-a10sr, sm501
- Supply PCI IDs; intel-lpss-pci
- Improve clocking; qcom_rpm
- Fix IRQ probing; ucb1x00-core
- Ensure fault log is cleared; da9052
- Remove NO_IRQ check; ucb1x00-core
- Supply I2C properties; intel-lpss-acpi, intel-lpss-pci
- Non standard declaration; tps65217, max8997-irq
- Remove unused code; lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi
- Make non-modular; altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core,
- OF bindings; ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808,
axp20x, lp873x, exynos5433-lpass, act8945a,
aspeed-scu, twl6040, arizona
- Bug Fixes
- Release OF pointer; qcom_rpm
- Avoid double shifting in suspend/resume; 88pm80x
- Fix 'defined but not used' error; exynos-lpass
- Fix 'sleeping whilst attomic'; atmel-hlcdc
-----BEGIN PGP SIGNATURE-----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=Ja7p
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core framework:
- Add the MFD bindings doc to MAINTAINERS
New drivers:
- X-Powers AC100 Audio CODEC and RTC
- TI LP873x PMIC
- Rockchip RK808 PMIC
- Samsung Exynos Low Power Audio
New device support:
- Add support for STMPE1600 variant to stmpe
- Add support for PM8018 PMIC to pm8921-core
- Add support for AXP806 PMIC in axp20x
- Add support for AXP209 GPIO in axp20x
New functionality:
- Add support for Reset to all STMPE variants
- Add support for MKBP event support to cros_ec
- Add support for USB to intel_soc_pmic_bxtwc
- Add support for IRQs and Power Button to tps65217
Fix-ups:
- Clean-up defunct author emails (da9063, max14577)
- Kconfig fixups (wm8350-i2c, as37220
- Constify (altera-a10sr, sm501)
- Supply PCI IDs (intel-lpss-pci)
- Improve clocking (qcom_rpm)
- Fix IRQ probing (ucb1x00-core)
- Ensure fault log is cleared (da9052)
- Remove NO_IRQ check (ucb1x00-core)
- Supply I2C properties (intel-lpss-acpi, intel-lpss-pci)
- Non standard declaration (tps65217, max8997-irq)
- Remove unused code (lp873x, db8500-prcmu, ab8500-debugfs,
cros_ec_spi)
- Make non-modular (altera-a10sr, intel_msic, smsc-ece1099,
sun6i-prcm, twl-core)
- OF bindings (ac100, stmpe, qcom-pm8xxx, qcom-rpm, rk808, axp20x,
lp873x, exynos5433-lpass, act8945a, aspeed-scu, twl6040, arizona)
Bugfixes:
- Release OF pointer (qcom_rpm)
- Avoid double shifting in suspend/resume (88pm80x)
- Fix 'defined but not used' error (exynos-lpass)
- Fix 'sleeping whilst attomic' (atmel-hlcdc)"
* tag 'mfd-for-linus-4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
mfd: arizona: Handle probe deferral for reset GPIO
mfd: arizona: Remove arizona_of_get_named_gpio helper function
mfd: arizona: Add DT options for max_channels_clocked and PDM speaker config
mfd: twl6040: Register child device for twl6040-pdmclk
mfd: cros_ec_spi: Remove unused variable 'request'
mfd: omap-usb-host: Return value is not 'const int'
mfd: ab8500-debugfs: Remove 'weak' function suspend_test_wake_cause_interrupt_is_mine()
mfd: ab8500-debugfs: Remove ab8500_dump_all_banks_to_mem()
mfd: db8500-prcmu: Remove unused *prcmu_set_ddr_opp() calls
mfd: ab8500-debugfs: Prevent initialised field from being over-written
mfd: max8997-irq: 'inline' should be at the beginning of the declaration
mfd: rk808: Fix RK818_IRQ_DISCHG_ILIM initializer
mfd: tps65217: Fix nonstandard declaration
mfd: lp873x: Remove unused mutex lock from struct lp873x
mfd: atmel-hlcdc: Do not sleep in atomic context
mfd: exynos-lpass: Mark PM functions as __maybe_unused
mfd: intel-lpss: Add default I2C device properties for Apollo Lake
mfd: twl-core: Make it explicitly non-modular
mfd: sun6i-prcm: Make it explicitly non-modular
mfd: smsc-ece1099: Make it explicitly non-modular
...
Current code uses devm_input_allocate_device() so don't explicitly call
input_free_device if input_register_device fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Jornada720 keyboard driver does not make use of anything from the
mach/hardware.h header, so this header can be removed.
Tested-by: Adam Wysocki <armlinux@chmurka.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Because events other that keyboard ones will be handled by now on by
other drivers, stop directly handling interrupts and instead listen to
the new notifier in the MFD driver.
Signed-off-by: Vic Yang <victoryang@google.com>
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A common way of multiplexing buttons on a single input in cheap devices is
to use a resistor ladder on an ADC. This driver supports that configuration
by polling an ADC channel provided by IIO.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch to using dev_dbg instead of naked printk so that output is uniform
with the other driver messages in the kernel.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch the jornada720 keyboard driver to obtain its interrupt from the
platform device, rather than via a hard-coded interrupt number obtained
from the mach/irqs.h header.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch the jornada720_kbd driver to use the devm_* APIs. This is in
preparation to removing the mach/irqs.h include from this driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit fe6b0dfaba ("Input: tegra-kbc - use reset framework")
accidentally converted _deassert to _assert, so there is no code
to wake up this hardware.
Fixes: fe6b0dfaba ("Input: tegra-kbc - use reset framework")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
"Two new drivers for touchscreen controllers:
- Silead touchscreen controllers
- SiS 9200 family touchscreen controllers
and a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: silead - remove some dead code
Input: sis-i2c - select CONFIG_CRC_ITU_T
Input: add driver for SiS 9200 family I2C touchscreen controllers
Input: ili210x - fix permissions on "calibrate" attribute
Input: elan_i2c - properly wake up touchpad on ASUS laptops
Input: add driver for Silead touchscreens
Input: elantech - fix debug dump of the current packet
Input: rotary_encoder - support binary encoding of states
Input: xpad - power off wireless 360 controllers on suspend
Input: i8042 - break load dependency between atkbd/psmouse and i8042
Input: synaptics-rmi4 - do not check for NULL when calling of_node_put()
Input: cros_ec_keyb - cleanup use of dev
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. This contains the following new
drivers promised in the last merge window:
- driver for touchscreen controller found in Surface 3
- driver for Pegasus Notetaker tablet
- driver for Atmel Captouch Buttons
- driver for Raydium I2C touchscreen controllers
- powerkey driver for HISI 65xx SoC
plus a few fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (40 commits)
Input: tty/vt/keyboard - use memdup_user()
Input: pegasus_notetaker - set device mode in reset_resume() if in use
Input: pegasus_notetaker - cancel workqueue's work in suspend()
Input: pegasus_notetaker - fix usb_autopm calls to be balanced
Input: pegasus_notetaker - handle usb control msg errors
Input: wacom_w8001 - handle errors from input_mt_init_slots()
Input: wacom_w8001 - resolution wasn't set for ABS_MT_POSITION_X/Y
Input: pixcir_ts - add support for axis inversion / swapping
Input: icn8318 - use of_touchscreen helpers for inverting / swapping axes
Input: edt-ft5x06 - add support for inverting / swapping axes
Input: of_touchscreen - add support for inverted / swapped axes
Input: synaptics-rmi4 - use the RMI_F11_REL_BYTES define in rmi_f11_rel_pos_report
Input: synaptics-rmi4 - remove unneeded variable
Input: synaptics-rmi4 - remove pointer to rmi_function in f12_data
Input: synaptics-rmi4 - support regulator supplies
Input: raydium_i2c_ts - check CRC of incoming packets
Input: xen-kbdfront - prefer xenbus_write() over xenbus_printf() where possible
Input: fix a double word "is is" in include/linux/input.h
Input: add powerkey driver for HISI 65xx SoC
Input: apanel - spelling mistake - "skiping" -> "skipping"
...
In cros_ec_keyb we stored "dev" in "struct cros_ec_keyb", but this was
the EC's dev pointer and not the keyboard's. Let's clean this up to
make it the keyboard's dev pointer. This could be useful in future
patches but also has the nice effect of changing a few printouts to
include the name of the keyboard device instead of the EC device, so we
will see:
[ 1.224648] cros-ec-keyb ff110000.spi:ec@0:keyboard-controller: valid_keys[00] = 0x14
instead of:
[ 1.224505] cros-ec-spi spi0.0: valid_keys[00] = 0x14
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The end ')' needs to be removed if the macro is ever used or there
would be a compiler error as it does not have a matching '('.
Signed-off-by: Clifton Barnes <clifton.a.barnes@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bitwise shift operator has lower priority than plus operator. So the
values on macros should be enclosed in parentheses.
For example, "(1 << 4 + 1)" means "(1 << (4 + 1))", but it is not expected
by the macros.
And also fix other two coding style problems reported by
scripts/checkpatch.pl.
Signed-off-by: Rui Teng <rui.teng@linux.vnet.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit f799a3d8fe ("Input: omap-keypad:
Remove dependencies to mach includes") removed users of the above
functions, but left them in the code.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As of 35f8679f57 ("Input: omap-keypad -
remove dead check") we no longer declare keypresses as spurious, therefore
we can use constant delay between scans.
Suggested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJW5j4RAAoJEHm+PkMAQRiGhVEH/0qZbM1J+WnCK92bm9+inCnB
JO2JViGIuCQB5BxljVMil2dzrw85D+dC7+fryr0wVBhhBlr0lXPJGSYCYYTEaI20
Wco5YlTmjRirUwmxWzBXvB5kvTdIaNfNYDcFch6lbsaLUNgqydNKtk08ckO/4k0D
AmaShW8swBiXE/RmHuj8H41ksHsnY8W62dlczEaAIfr4kluPX/kKnyXpmpvmZm1j
sM4fskPlq+Jz5pOXXFsFfrhiBgpSUnwSj1tNwK5+DkmaVnWOkPuwkqLBWqpy4pzm
GTeDBdf5/ixGxgNsZ2VWtbPnc2wEP7SIcu45MU7QFw5kqwDN2nN63BRVXI5Z5qY=
=RFx2
-----END PGP SIGNATURE-----
Merge tag 'v4.5' into next
Merge with Linux 4.5 to get PROPERTY_ENTRY_INTEGER() that is needed to
fix pxa/raumfeld rotary encoder properties.
On error syscon_regmap_lookup_by_phandle() returns ERR_PTR() value,
which makes a check for NULL invalid and may lead to oops on error
path.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A dependency on ARCH_SHMOBILE seems to be the best option for sh_keysc:
* For Super H based SoCs: sh_keysc is used on SH_MIGOR, SH_ECOVEC, SH_KFR2R09,
SH_7722_SOLUTION_ENGINE, and SH_7724_SOLUTION_ENGINE, which depend on
either CPU_SUBTYPE_SH7722 or CPU_SUBTYPE_SH7724, and both select
ARCH_SHMOBILE.
* For ARM Based SoCs: Since the removal of legacy (non-multiplatform) support
this driver has not been used by any Renesas ARM based SoCs. The Renesas
ARM based SoCs currently select ARCH_SHMOBILE, however, it is planned
that this will no longer be the case.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The SNVS power key driver has suspend/resume functions that
are accessed using SIMPLE_DEV_PM_OPS, which hide the reference
when CONFIG_PM_SLEEP is not set, resulting in a warning about
unused functions:
drivers/input/keyboard/snvs_pwrkey.c:183:12: error: 'imx_snvs_pwrkey_suspend' defined but not used [-Werror=unused-function]
drivers/input/keyboard/snvs_pwrkey.c:194:12: error: 'imx_snvs_pwrkey_resume' defined but not used [-Werror=unused-function]
This adds __maybe_unused annotations to let the compiler know
it can silently drop the function definition.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The spear keyboard driver uses #ifdef CONFIG_PM to hide its
power management functions, but then uses references from
SIMPLE_DEV_PM_OPS that are only present if both CONFIG_PM
and CONFIG_PM_SLEEP are set, resulting in a warning about unused
functions:
drivers/input/keyboard/spear-keyboard.c:292:12: error: 'spear_kbd_suspend' defined but not used [-Werror=unused-function]
drivers/input/keyboard/spear-keyboard.c:345:12: error: 'spear_kbd_resume' defined but not used [-Werror=unused-function]
This removes the #ifdef and instead uses a __maybe_unused
annotation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ACPI binding to the goldfish events driver.
Signed-off-by: Jason Hu <jia-cheng.hu@intel.com>
Signed-off-by: Jin Qian <jinqian@android.com>
Signed-off-by: Alan <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The adp5589 has row 5, don't skip it when creating the GPIO mapping.
Otherwise the pin gets reserved as used and it is not possible to use it as
a GPIO.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
for_each_child_of_node performs an of_node_get on each iteration, so
to break out of the loop an of_node_put is required.
Found using Coccinelle.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support to disable buttons from DT via status property if given button
is not supported on given platforms. This will help re-using existing dtsi
files across multiple platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allow specifying name if input device via device tree property. This helps
userspace code to get name and perform proper event to key mapping in some
cases (for example, on Android).
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 4ea14a53d8 ("Input: gpio-keys - report
error when disabling unsupported key") tried let user know that they
attempted to disable an unsupported key, unfortunately the check is wrong
as it believes that all codes are invalid. Fix it by ensuring that keys
that we try to disable are subset of keys (or switches) that device
reports.
Fixes: 4ea14a53d8 ("Input: gpio-keys - report error when disabling unsupported key")
Reported-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit da1f026b53 ("Keyboard: omap-keypad:
use matrix_keypad.h") switched the driver to use matrix keypad
infrastructure, which made array of keycodes to be unsigned short, and
caused the test for negativity never trigger. This leads to the following
static checker warning:
drivers/input/keyboard/omap-keypad.c:158 omap_kp_tasklet()
warn: 'keycodes[]' is never negative.
Given that we did not care about this check for a few years already let's
simply remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It feels like we should set the tasklet data before enabling it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove the unneded semicolon since it is clearly a typo error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver handles wakeup irq correctly using device_init_wakeup and
enable_irq_wake. There's no need to use IRQF_NO_SUSPEND while registering
the interrupt.
This patch removes the use of IRQF_NO_SUSPEND flag.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Though the tegra-kbc driver should/will continue to support the legacy
"nvidia,wakeup-source" property to enable keyboard as the wakeup source,
we need to add support for the new standard property "wakeup-source".
This patch adds support for "wakeup-source" property in addition to the
existing "nvidia,wakeup-source" property.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This changAdd support for EV_ABS / EV_REL events to the gpio-keys-polled driver.
The driver already allows specifying what type of events (key / rel / abs)
a button generates when pressed, but for rel / abs axis we also need to
specify which value this specific gpio represents.
One use case is digital joysticks / direction-pads which are hooked up to
gpio, in this case we've left and right buttons which we want to map to
EV_ABS, ABS_X and we want generate events for left with a value of -1 and
for right with a value of +1 (and similar for up / down and ABS_Y).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver depends on GOLDFISH but there isn't a build dependency
so it's a good idea to allow the driver to be built even if that
option is disabled, if the COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and can be checked if a patch would break the build.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In the cases where the gpio chip fails to acquire the current state an
error is reported back to gpio_keys. This is currently interpreted as if
the line went high, which just confuses the developer.
This patch introduces an error print in this case and skipps the
reporting of a input event; to aid in debugging this issue.
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWB9f6AAoJEHm+PkMAQRiGiFMIAJYFLIkF/dXFYMNPGsRGRGYO
SsQkfYzjy4i/yloyVlGB33e6dqxWdVgCeqYC77TO+1CBq34o6dqM4PACTrhjtS+3
qQvaP/qn6cSoaGIkdD3v43CCiwMpZZ5+Uj7F7Uz8N4twrpykOZFMM5T7f1lrsG2F
wJGafmvok9NU2F2wYwaJ8JrzsF6iO6ibFeB8BosRF5Ba4nKqiXVI0xNa0R8PFDm3
tbh/IkkqokemEqnHyWyszhGFsCQupi+QgsjY/LhWUcCaL7HLEgJmkBX0tXNlgMmK
TFCq7L8Bigu4nlgZ/iVUB9kh4GTBNVcbdRVN3loJFlczFJlIAa171OVlfRu3lvU=
=m29x
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc3' into next
Merge with Linux 4.3-rc3 to bring in MFD DA9062 changes to merge DA9062
OnKey driver.
If omap4_keypad_parse_dt() fails we returned the error code but we
missed releasing keypad_data.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
This introduces two brand new touchscreen drivers (Colibri and
imx6ul_tsc), some small driver fixes, and we are no longer report
errors from evdev_flush() as users do not really have a way of
handling errors, error codes that we were returning were not on the
list of errors supposed to be returned by close(), and errors were
causing issues with one of older versions of systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_keypad - remove obsolete comment
Input: touchscreen - add imx6ul_tsc driver support
Input: Add touchscreen support for Colibri VF50
Input: i8042 - lower log level for "no controller" message
Input: evdev - do not report errors form flush()
Input: elants_i2c - extend the calibration timeout to 12 seconds
Input: sparcspkr - fix module autoload for OF platform drivers
Input: regulator-haptic - fix module autoload for OF platform driver
Input: pwm-beeper - fix module autoload for OF platform driver
Input: ab8500-ponkey - Fix module autoload for OF platform driver
Input: cyttsp - remove unnecessary MODULE_ALIAS()
Input: elan_i2c - add ACPI ID "ELAN1000"
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
When trying to disable a key that is not supported by the device we should
report error, not do nothing and report success:
root@yocto:/sys/devices/soc0/gpio-keys# cat keys
114-116
root@yocto:/sys/devices/soc0/gpio-keys# echo 77 > keys
root@yocto:/sys/devices/soc0/gpio-keys#
We want 'echo 77 > keys' to report an error, but silence to give us an
illusion that all is 'ok'.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fix from Dmitry Torokhov:
"A small fixup to gpio_keys_polled driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_keys_polled - request GPIO pin as input.
GPIOF_IN flag was lost in:
Commit 633a21d80b4a("input: gpio_keys_polled: Add support for GPIO
descriptors").
Without this flag, legacy code path (for non-descriptor GPIO declarations)
would configure GPIO as output (0 meaning GPIOF_DIR_OUT | GPIOF_INIT_LOW).
Cc: stable@vger.kernel.org
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ChromeOS EC keyboard driver config depends on CROS_EC_PROTO but
MFD_CROS_EC selects CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the keyboard driver
is registered by the ChromeOS EC mfd driver, KEYBOARD_CROS_EC really
should depend on MFD_CROS_EC. And because this config option selects
CROS_EC_PROTO, that dependency is met as well. So make the driver
to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Several cap11xx variants have LEDs that be can be controlled; let's plug
the driver into the LED subsystem.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVrBp0AAoJEHm+PkMAQRiGADsH/iCVjA1x+a19xpeuHNJcjcQR
Lin8td8zdUxereBNQOFjnkhCmKtzLODXGkQdYFaWZx8mbEQ93wC+nPV8O+LsqPbI
T/2MjJ78IjlNsoTyE4b1AhqpASsxrLZJNB+f9dd251f1BSAzKfRER0G46WxbOPN7
9HdzCMbtx03ZJkr9baE6alljxA43O5mpDzpotKIagfTMQr5h0ra16uXlmVXFjHRs
roNJsugwKxJPnVmLWWOM1JsAjRSMBAXQUQxhJJCMDOhgZZ5KR1z6L30ESeFTUhvh
WG/2MEfyVYXn91kV0N+AUCuOFHTv6uiaz3RaRVJFDSv3sPOh1WQ9tQHxyrBsqyY=
=MA/P
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc3' into next
Sync up with Linux 4.2-rc3 to bring in infrastructure (OF) pieces.
Instead of inventing a new property name, let's use "wakeup-source" to
be consistent with other driver and subsystem bindings.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
add snvs power key driver.
It work in imx chips after i.mx6sx
ON/OFF key used power on/off whole system.
This driver make it wakeup from suspend state when short press
ON/OFF key.
Long time press will trig SNVS power off chip without software
intervention.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull second round of input updates from Dmitry Torokhov:
"A new driver for Weida wdt87xx touch controllers, and a bunch of
fixups for other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wdt87xx_i2c - add a scaling factor for TOUCH_MAJOR event
Input: wdt87xx_i2c - remove stray newline in diagnostic message
Input: arc_ps2 - add HAS_IOMEM dependency
Input: wdt87xx_i2c - fix format warning
Input: improve parsing OF parameters for touchscreens
Input: edt-ft5x06 - mark as direct input device
Input: use for_each_set_bit() where appropriate
Input: add a driver for wdt87xx touchscreen controller
Input: axp20x-pek - fix reporting button state as inverted
Input: xpad - re-send LED command on present event
Input: xpad - set the LEDs properly on XBox Wireless controllers
Input: imx_keypad - check for clk_prepare_enable() error
Pull input subsystem updates from Dmitry Torokhov:
"Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
hardwired within the input core but use LED subsystem and so allow use
of different triggers; Hans de Goede did a large update for the ALPS
touchpad driver; we have new TI drv2665 haptics driver and DA9063
OnKey driver, and host of other drivers got various fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: pixcir_i2c_ts - fix receive error
MAINTAINERS: remove non existent input mt git tree
Input: improve usage of gpiod API
tty/vt/keyboard: define LED triggers for VT keyboard lock states
tty/vt/keyboard: define LED triggers for VT LED states
Input: export LEDs as class devices in sysfs
Input: cyttsp4 - use swap() in cyttsp4_get_touch()
Input: goodix - do not explicitly set evbits in input device
Input: goodix - export id and version read from device
Input: goodix - fix variable length array warning
Input: goodix - fix alignment issues
Input: add OnKey driver for DA9063 MFD part
Input: elan_i2c - add product IDs FW names
Input: elan_i2c - add support for multi IC type and iap format
Input: focaltech - report finger width to userspace
tty: remove platform_sysrq_reset_seq
Input: synaptics_i2c - use proper boolean values
Input: psmouse - use true instead of 1 for boolean values
Input: cyapa - fix a few typos in comments
Input: stmpe-ts - enforce device tree only mode
...
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
output. Simplify drivers accordingly.
Note that in the case of the drv260x driver error checking is more
strict now because -ENOSYS is reported to the caller now. But this
should only be returned if GPIOLIB is disabled which shouldn't happen as
the driver depends on GPIOLIB.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Chromebooks can have more than one Embedded Controller so the
cros_ec device id has to be incremented for each EC registered.
Add a new structure to represent multiple EC as different char
devices (e.g: /dev/cros_ec, /dev/cros_pd). It connects to
cros_ec_device and allows sysfs inferface for cros_pd.
Also reduce number of allocated objects, make chromeos sysfs
class object a static and add refcounting to prevent object
deletion while command is in progress.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
rajeev-dlh.kumar@st.com email-id doesn't exist anymore as I have left the
company.
Signed-off-by: Rajeev Kumar <rajeevkumar.linux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
max7359_build_keycode() does the same thing as matrix_keypad_build_keymap(),
but the latter can also handle DT bindings.
Tested on beagleboard-xm.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In datasheet of max7359 there is the following description of this flag:
0 - INT cleared when FIFO empty,
1 - INT cleared after host read. In this mode, I2C should read
FIFO until interrupt condition removed, or further INT may be lost.
So, if we set this flag, we have to read FIFO until it becomes empty. But
in interrupt we read FIFO just once. This lead to "keyboard" hang until
reboot, if we press several keys, because of interrupt handler read just
one "press" from FIFO and clear interrupt.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The event mask was specified as 0xF (4 bits) when in reality is 0x1F (5
bits) in order to be capable of representing all FIFO length values from
0 to 16.
This caused a problem: when the keypad reported 16 pending events the
driver took it as 0, and did nothing. This in turn caused the keypad to
re-issue the interrupt over and over again.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pull mask is created by looping each row (column) and building an
8-bit integer with the configuration. It is written byte-by-byte, when
we reach the end of the rows (columns) or we're at the 3rd line (which
finishes the first byte, since each pin is 2bits on the mask).
However, this only works if we have at most 8 pins (2 bytes), which is
not the case for the ADP5589. So, write the byte at each boundary (every
4 rows/columns).
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
Pull more input subsystem updates from Dmitry Torokhov:
- an update to Atmel MXT driver that makes it functional on Google
Pixel 2 boxes (both touchpad and touchscreen)
- a new VMware VMMouse driver that should allow us drop X vmmouse
driver that requires root privileges (since it accesses ioports)
- XBox One controllers now support force feedback (rumble)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: lm8333 - fix broken email address
Input: cyapa - fix setting suspend scan rate
Input: elan_i2c - fix calculating number of x and y traces.
Input: elan_i2c - report hovering contacts
Input: elants_i2c - zero-extend hardware ID in firmware name
Input: alps - document separate pointstick button bits for V2 devices
Input: atmel_mxt_ts - add support for Google Pixel 2
Input: xpad - add rumble support for Xbox One controller
Input: ff-core - use new debug macros
Input: add vmmouse driver
Input: elan_i2c - adjust for newer firmware pressure reporting
My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cycle:
- A new GPIO hogging mechanism has been added. This can
be used on boards that want to drive some GPIO line high,
low, or set it as input on boot and then never touch it
again. For some embedded systems this is bliss and
simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs
in bulk as was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header
any GPIO driver needs to include or something is wrong.
Cleanups restricting drivers to this include are welcomed
if tested.
- Sort the GPIO Kconfig and split it into submenus, as
it was becoming and unstructured, illogical and
unnavigatable mess. I hope this is easier to follow.
Menus that require a certain subsystem like I2C can
now be hidden nicely for example, still working on
others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and
F71869A variants.
- The MIPS Loongson driver has been moved to
drivers/gpio for consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is
a "hard IP" block from Synopsys which has started to
turn up in so diverse architectures as X86 Quark, ARC
and a slew of ARM systems. So even though it's not an
expander, it's generic enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long
discussion with Daniel Vetter et al, tracing back to
the shootout at the kernel summit where DRM drivers
and sub-componentization was discussed. In this case
a mock GPIO is assumed to be the best compromise
gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's
see.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QFbC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
To save people some time let's document that we do not want new quirks for
"force-release" keys in the kernel and that they should patch userspace
(udev) instead.
Suggested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the comment right before explains, the keyboard state is to be cleared
only if the EC wasn't a wakeup source in the last suspend.
Without this commit, there's an unneeded delay when resuming from suspend
and we also lose the key that was pressed while suspended.
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All systems using the TC3589x multifunction expander uses
devicetree, so don't clutter the place with a lot of
and assume it is there.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver can only get its platform data from the device tree, and all
platforms using it do that. Localize the platform data for the keypad. A
later patch will enforce the device tree / OF dependence.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVD1VGAAoJEHm+PkMAQRiG7yoH/juKOQ1zbxi5M+mleDEEJtA0
RxQSojqEMWIKrWi8PNZxjENn1OZB6XOLIXOhlyAZBrmgsjO34p1DyXlZMznr/R8W
kQ2Xxs061hRtB3OuruMIqOApUrjuqsaCwgbgUS1qWmqZcoyZN4oELyZMP6OOlqv5
UUBZm8MfyXGyxrCcg39mjct3VEOhiuEcvL6SUxOC380CdSVAnyqHFPcz0JVqMUn9
9RUBs0T9cMdhb0mZ2bfXzt6AKArj63G2nXOum+VzFcvspSm2U+MPIDCuoE+ZbTPS
jqIAgG0rj1ezRyb5oeJrvlU0Yy3u/cXoMPs9+kORvpladooYNLti8ovh6qllm0I=
=d/ye
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc5' into next
Merge with the latest upstream to synchronize Synaptics changes
and bring in new infrastructure pieces.
Conflicts:
drivers/input/mouse/synaptics.c
This adds a key input driver for the keys found on the h3xxx
iPAQ series.
Based on a driver from handhelds.org 2.6.21 kernel, written
by Alessandro GARDICH.
Signed-off-by: Alessandro GARDICH <gremlin@gremlin.it>
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
Currently, plat->irqtype is only set to IRQF_TRIGGER_FALLING. This
patch sets the ONESHOT flag directly in request_threaded_irq() to
enforce the flag without being affected by future changes to
plat->irqtype.
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Signed-off-by: Valentin Rothberg <Valentin.Rothberg@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The gpio binding document says that new code should always use named
gpios. Patch 40b73183 added support to parse a list of gpios from child
nodes, but does not make it possible to use named gpios. This patch adds
the con_id property and implements it is done in gpiolib.c, where the
old-style of using unnamed gpios still works.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Acked-by: Bryan Wu <cooloney@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Broadcom Keypad controller is used to interface a SoC with a matrix-type
keypad device. The keypad controller supports multiple row and column
lines. A key can be placed at each intersection of a unique row and a
unique column. The keypad controller can sense a key-press and key-release
and report the event using an interrupt to the CPU.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The struct cros_ec_command will be used as an ioctl() argument for the
API to control the ChromeOS EC from user-space. So the data structure
has to be 64-bit safe to make it compatible between 32 and 64 avoiding
the need for a compat ioctl interface. Since pointers are self-aligned
to different byte boundaries, use fixed size arrays instead of pointers
for transferring ingoing and outgoing data with the Embedded Controller.
Also, re-arrange struct members by decreasing alignment requirements to
reduce the needing padding size.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull more input updates from Dmitry Torokhov:
"The second round of updates for the input subsystem.
Updates to ALPS an bfin_roraty drivers and a couple oother fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - use IS_ENABLED instead of homegrown code
Input: bfin_rotary - introduce open and close methods
Input: bfin_rotary - convert to use managed resources
Input: bfin_rotary - use generic IO functions
Input: bfin_rotary - move pin lists into into platform data
Input: bfin_rotary - move platform header to linux/platform_data
Input: bfin_rotary - mark suspend and resume code as __maybe_unused
Input: bfin_rotary - fix potential oops in interrupt handler
Input: ALPS - move v7 packet info to Documentation and v6 packet info
Input: ALPS - fix confusing comment in protocol data
Input: ALPS - do not mix trackstick and external PS/2 mouse data
Input: ALPS - fix trackstick detection on some Dell Latitudes
Input: ALPS - consolidate setting protocol parameters
Input: ALPS - split protocol data from model info
Input: ALPS - make Rushmore a separate protocol
Input: ALPS - renumber protocol numbers
Input: adi - remove an unnecessary check
Input: pxa27x_keypad - remove an unneeded NULL check
Input: soc_button_array - use "Windows" key for "Home"
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
* Line termination only requires one extra space at the end of the
buffer. Use PAGE_SIZE - 1 instead of PAGE_SIZE - 2 when formatting.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Static checkers complain about this NULL check because we dereference it
without checking a couple lines later. This function is only called
when "keypad->pdata" is non-NULL so we can just delete the NULL test.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[Dmitry: remove the variable altogether given that it is used just once and
dereference directly.]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Remove some left-over ARM only includes in order to enable building on
ARM64. __raw_{read,write}l were getting implicitly included, so add
linux/io.h include.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is a I2C driver, so it's wrong to use platform prefix for the
modalias. We have all needed i2c aliases coming form MODULE_DEVICE_TABLE,
so let's remove the wrong and unneeded cap11xx modalias.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Daniel Mack <linux@zonque.org>
Reviewed-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUsuDQAAoJEHm+PkMAQRiGnecH/0RO9UKnEduOTRPaZGXAjGI8
N0FvNia8qn7f+XnvN62pG/YZZqi2uvuy37vwAXMtS6KXEgaDG9Wq4fVrhOaJ5VgL
QOmPdVGUa+1PuPcMYj/QLIFRfIHvIY/XVZWXrcIyYfQdBAAoJ2q23qx/yFmdyTwf
+enAv+PV4ZVNMEANyN9KS7xX5gPbSDl36AOhm6lXDvrlem4mbnhRuUtYez9R8KTK
VNfkKZQRDOgl4/ns0ndzpAUhaDj1JJGoLRgMXKna33XgtzSEL4XijvImdnoIXp5N
Z98Jc1N5Vg5OcUFeGJC3bRR27m39xoOHQk2ufY43uAIfB3Ez/C7m/r7b50ZVWfs=
=J7TO
-----END PGP SIGNATURE-----
Merge tag 'v3.19-rc4' into next
Merge with mainline to bring in the latest thermal and other changes.
According to Documentation/CodingStyle - Chapter 14:
"The preferred form for passing a size of a struct is the following:
p = kmalloc(sizeof(*p), ...);
The alternative form where struct name is spelled out hurts readability and
introduces an opportunity for a bug when the pointer variable type is changed
but the corresponding sizeof that is passed to a memory allocator is not."
So do it as recommended.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fixes from Dmitry Torokhov:
"Fixes for v7 protocol for ALPS devices and few other driver fixes.
Also users can request input events to be stamped with boot time
timestamps, in addition to real and monotonic timestamps"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: hil_kbd - fix incorrect use of init_completion
Input: alps - v7: document the v7 touchpad packet protocol
Input: alps - v7: fix finger counting for > 2 fingers on clickpads
Input: alps - v7: sometimes a single touch is reported in mt[1]
Input: alps - v7: ignore new packets
Input: evdev - add CLOCK_BOOTTIME support
Input: psmouse - expose drift duration for IBM trackpoints
Input: stmpe - bias keypad columns properly
Input: stmpe - enforce device tree only mode
mfd: stmpe: add pull up/down register offsets for STMPE
Input: optimize events_per_packet count calculation
Input: edt-ft5x06 - fixed a macro coding style issue
Input: gpio_keys - replace timer and workqueue with delayed workqueue
Input: gpio_keys - allow separating gpio and irq in device tree
The successive init_completion calls should be reinit_completion calls.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Acked-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allwinnner sunxi SoCs have a low resolution adc (called lradc) which is
specifically designed to have various (tablet) keys (ie home, back, search,
etc). attached to it using a resistor network. This adds a driver for this.
There are 2 channels, currently this driver only supports chan0 since there
are no boards known to use chan1.
This has been tested on an olimex a10s-olinuxino-micro, a13-olinuxino, and
a20-olinuxino-micro.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Two new drivers for Elan hardware (for I2C touchpad and touchscreen
found in several Chromebooks and other devices), a driver for Goodix
touch panel, and small fixes to Cypress I2C trackpad and other input
drivers.
Also we switched to use __maybe_unused instead of gating suspend/
resume code with #ifdef guards to get better compile coverage"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (27 commits)
Input: gpio_keys - fix warning regarding uninitialized 'button' variable
Input: add support for Elan eKTH I2C touchscreens
Input: gpio_keys - fix warning regarding uninitialized 'irq' variable
Input: cyapa - use 'error' for error codes
Input: cyapa - fix resuming the device
Input: gpio_keys - add device tree support for interrupt only keys
Input: amikbd - allocate temporary keymap buffer on the stack
Input: amikbd - fix build if !CONFIG_HW_CONSOLE
Input: lm8323 - missing error check in lm8323_set_disable()
Input: initialize device counter variables with -1
Input: initialize input_no to -1 to avoid subtraction
Input: i8042 - do not try to load on Intel NUC D54250WYK
Input: atkbd - correct MSC_SCAN events for force_release keys
Input: cyapa - switch to using managed resources
Input: lifebook - use "static inline" instead of "inline" in lifebook.h
Input: touchscreen - use __maybe_unused instead of ifdef around suspend/resume
Input: mouse - use __maybe_unused instead of ifdef around suspend/resume
Input: misc - use __maybe_unused instead of ifdef around suspend/resume
Input: cap11xx - support for irq-active-high option
Input: cap11xx - add support for various cap11xx devices
...
All keypad column pins used as inputs should be pulled up on the STMPE24xx,
but this is not done by the current driver. Add some logic that will do
this properly. The STMPE1601 also has a keypad controller, but explicitly
does *NOT* require you to set up any pull-ups.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The STMPE keypad controller is only used with device tree configured
systems, so force the configuration to come from device tree only, and now
actually get the rows and cols from the device tree too.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We do not need to roll our own implementation of delayed work now that we
have proper implementation of mod_delayed_work.
For interrupt-only driven buttons we retain the timer, but we rename
it to release_timer to better reflect its purpose.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change allows specify interrupt for buttons separately form gpio,
potentially allowing to form several "clusters" of buttons on
different interrupts.
Button defined without both gpio and irq in device tree is a hared error
instead of a warning now.
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
Commit af906faabc ("Input: gpio_keys - fix warning regarding uninitialized
'irq' variable") introduced the following build warning:
drivers/input/keyboard/gpio_keys.c:625:16: warning: 'button' may be used uninitialized in this function [-Wmaybe-uninitialized]
Move the 'button' initialization to a proper location to avoid such warning.
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit f2d347ff70 ("Input: gpio_keys - add device tree support for
interrupt only keys") caused the following build warning:
drivers/input/keyboard/gpio_keys.c: In function 'gpio_keys_probe':
drivers/input/keyboard/gpio_keys.c:647:15: warning: 'irq' may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/input/keyboard/gpio_keys.c:622:7: note: 'irq' was declared here
Move button->irq initialization into proper branch and get rid of the
temporary.
Reported-by: Olof's autobuilder <build@lixom.net>
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
The alternative of CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME may be
replaced with CONFIG_PM too.
Make these changes in 2 files under drivers/input/.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Ferruh Yigit <fery@cypress.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This features already exists for board config setups. Add support for
device tree based systems.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Allocate the temporary buffer needed for initialization of the console
keyboard maps (512 bytes, as NR_KEYS = 256) on the stack instead of
statically, to reduce kernel size.
add/remove: 0/1 grow/shrink: 0/0 up/down: 0/-512 (-512)
function old new delta
temp_map 512 - -512
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If CONFIG_HW_CONSOLE is not set:
drivers/built-in.o: In function `amikbd_probe':
amikbd.c:(.init.text+0x3e4e): undefined reference to `key_maps'
amikbd.c:(.init.text+0x3dd4): undefined reference to `key_maps'
To fix this, extract the initialization of the console keyboard maps
into amikbd_init_console_keymaps(), protected by #ifdef
CONFIG_HW_CONSOLE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The missing error handling here is not especially harmful but static
checkers complain that "i" can be used uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Without the change either no scancode would be reported on release of
force_release keys, or - if the key is marked as force_release erroneously
- the release event and the scancode would be reported in separate reports
to the input layer.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make use of device property API in this driver so that both OF based
system and ACPI based system can use this driver.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
GPIO descriptors are the preferred way over legacy GPIO numbers
nowadays. Convert the driver to use GPIO descriptors internally but
still allow passing legacy GPIO numbers from platform data to support
existing platforms.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some applications need to use the irq-active-high push-pull option.
This allows it be enabled in the device tree child node.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are variants of the cap11xx device with a varying number of
capacitance detection channels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are several devices in cap11xx family besides cap1106. The driver can
be made to support all of them, so let's give it more generic name.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"A bunch of fixes for minor defects reported by Coverity, a few driver
fixups and revert of i8042.nomux change so that we are once again
enable active MUX mode if box claims to support it"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: i8042 - disable active multiplexing by default"
Input: altera_ps2 - use correct type for irq return value
Input: altera_ps2 - write to correct register when disabling interrupts
Input: max77693-haptic - fix potential overflow
Input: psmouse - remove unneeded check in psmouse_reconnect()
Input: vsxxxaa - fix code dropping bytes from queue
Input: ims-pcu - fix dead code in ims_pcu_ofn_reg_addr_store()
Input: opencores-kbd - fix error handling
Input: wm97xx - adapt parameters to tosa touchscreen.
Input: i8042 - quirks for Fujitsu Lifebook A544 and Lifebook AH544
Input: stmpe-keypad - fix valid key line bitmask
Input: soc_button_array - update calls to gpiod_get*()
The bitmask comment says it will enable GPIO 8-14 and 16-20 for keypad use,
but it actually enables GPIO 8-11 and 13-20 due to a bit error.
Instead of masking of the "hole" at GPIO 12 (which is used for keypad
output 4) mask of the proper "hole" at GPIO 15.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change switches to using devm_* managed resources APIs to
request the resources in probe to simplify probe error path and
module unloading.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change switches ithe driver to use devm_* APIs to allocate resources.
This helps to simplify failure path in probe function and module unloading
and does away with remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change switches the driver to use devm_* managed resources APIs to
request the resources in probe to simplify probe error path and module
unloading and does away with remove function.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
