If mv643xx_eth_shared_of_probe() fails, mv643xx_eth_shared_probe()
leaves clk enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1199:68C0 USB ID is reused by Sierra WP7607 which requires the DTR
quirk to be detected. Apply QMI_QUIRK_SET_DTR unconditionally as
already done for other IDs shared between different devices.
Signed-off-by: Beniamino Galvani <bgalvani@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC IP is little-endian and used on several kind of CPU (big or little
endian). Main callbacks functions of the stmmac drivers take care about
it. It was not the case for dwmac4_get_timestamp function.
Fixes: ba1ffd74df ("stmmac: fix PTP support for GMAC4")
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function-local variable "delay" enters the loop interpreted as delay
in bits. However, inside the loop it gets overwritten by the result of
mlxsw_sp_pg_buf_delay_get(), and thus leaves the loop as quantity in
cells. Thus on second and further loop iterations, the headroom for a
given priority is configured with a wrong size.
Fix by introducing a loop-local variable, delay_cells. Rename thres to
thres_cells for consistency.
Fixes: f417f04da5 ("mlxsw: spectrum: Refactor port buffer configuration")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU port is special and does not need to obey VLAN restrictions as
far as untagged traffic goes, also, having the CPU port be part of a
particular PVID is against the idea of keeping it tagged in all VLANs.
Fixes: ca89319483 ("net: dsa: b53: Keep CPU port as tagged in all VLANs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We assume in the bcm_sf2 driver that the DSA master network device
supports ethtool_ops::{get,set}_wol operations, which is not a given.
Avoid de-referencing potentially non-existent function pointers and
check them as we should.
Fixes: 96e65d7f3f ("net: dsa: bcm_sf2: add support for Wake-on-LAN")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SYSTEMPORT has its RXCHK parser block that attempts to validate the
packet structures, unfortunately setting the L2 header check bit will
cause Bridge PDUs (BPDUs) to be incorrectly rejected because they look
like LLC/SNAP packets with a non-IPv4 or non-IPv6 Ethernet Type.
Fixes: 4e8aedfe78c7 ("net: systemport: Turn on offloads by default")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.
Fixes: a2482d2ce3 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some PHY drivers like the generic one do not provide a read_status
callback on their own but rely on genphy_read_status being called
directly.
With the current code, this results in a NULL function pointer call.
Call genphy_read_status instead when there is no specific callback.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the ethtool_regs version is set to 0 for FEC devices.
Use this field to store the register dump version exposed by the
kernel. The choosen version 2 corresponds to the kernel compile test:
#if defined(CONFIG_M523x) || defined(CONFIG_M527x)
|| defined(CONFIG_M528x) || defined(CONFIG_M520x)
|| defined(CONFIG_M532x) || defined(CONFIG_ARM)
|| defined(CONFIG_ARM64) || defined(CONFIG_COMPILE_TEST)
and version 1 corresponds to the opposite. Binaries of ethtool unaware
of this version will dump the whole set as usual.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The of_find_device_by_node() takes a reference to the underlying device
structure, we should release that reference.
Signed-off-by: Huang Zijiang <huang.zijiang@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell reported the following race in the phylib state machine
(quoting from his mail):
if (phy_polling_mode(phydev) && phy_is_started(phydev))
phy_queue_state_machine(phydev, PHY_STATE_TIME);
state = PHY_UP
thread 0 thread 1
phy_disconnect()
+-phy_is_started()
phy_is_started() |
`-phy_stop()
+-phydev->state = PHY_HALTED
`-phy_stop_machine()
`-cancel_delayed_work_sync()
phy_queue_state_machine()
`-mod_delayed_work()
At this point, the phydev->state_queue() has been added back onto the
system workqueue despite phy_stop_machine() having been called and
cancel_delayed_work_sync() called on it.
Fix this by protecting the complete operation in thread 0.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell suggested to remove the locking from phy_is_started() because
the read is atomic anyway and actually the locking may be more
misleading.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Suggested-by: Russell King - ARM Linux admin <linux@armlinux.org.uk>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value of ->num_ports comes from bcm_sf2_sw_probe() and it is less
than or equal to DSA_MAX_PORTS. The ds->ports[] array is used inside
the dsa_is_user_port() and dsa_is_cpu_port() functions. The ds->ports[]
array is allocated in dsa_switch_alloc() and it has ds->num_ports
elements so this leads to a static checker warning about a potential out
of bounds read.
Fixes: 8cfa94984c ("net: dsa: bcm_sf2: add suspend/resume callbacks")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GPIO interrupt controller on the espressobin board only supports edge interrupts.
If one enables the use of hardware interrupts in the device tree for the 88E6341, it is
possible to miss an edge. When this happens, the INTn pin on the Marvell switch is
stuck low and no further interrupts occur.
I found after adding debug statements to mv88e6xxx_g1_irq_thread_work() that there is
a race in handling device interrupts (e.g. PHY link interrupts). Some interrupts are
directly cleared by reading the Global 1 status register. However, the device interrupt
flag, for example, is not cleared until all the unmasked SERDES and PHY ports are serviced.
This is done by reading the relevant SERDES and PHY status register.
The code only services interrupts whose status bit is set at the time of reading its status
register. If an interrupt event occurs after its status is read and before all interrupts
are serviced, then this event will not be serviced and the INTn output pin will remain low.
This is not a problem with polling or level interrupts since the handler will be called
again to process the event. However, it's a big problem when using level interrupts.
The fix presented here is to add a loop around the code servicing switch interrupts. If
any pending interrupts remain after the current set has been handled, we loop and process
the new set. If there are no pending interrupts after servicing, we are sure that INTn has
gone high and we will get an edge when a new event occurs.
Tested on espressobin board.
Fixes: dc30c35be7 ("net: dsa: mv88e6xxx: Implement interrupt support.")
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylib enables interrupts before phy_start() has been called, and if
we receive an interrupt in a non-started state, the interrupt handler
returns IRQ_NONE. This causes problems with at least one Marvell chip
as reported by Andrew.
Fix this by handling interrupts the same as in phy_mac_interrupt(),
basically always running the phylib state machine. It knows when it
has to do something and when not.
This change allows to handle interrupts gracefully even if they
occur in a non-started state.
Fixes: 2b3e88ea65 ("net: phy: improve phy state checking")
Reported-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlx5 driver creates xdp redirect hw queues unconditionally on
netdevice open, This is great until someone starts redirecting XDP traffic
via ndo_xdp_xmit on mlx5 device and changes the device configuration at
the same time, this might cause crashes, since the other device's napi
is not aware of the mlx5 state change (resources un-availability).
To fix this we must synchronize with other devices napi's on the system.
Added a new flag under mlx5e_priv to determine XDP TX resources are
available, set/clear it up when necessary and use synchronize_rcu()
when the flag is turned off, so other napi's are in-sync with it, before
we actually cleanup the hw resources.
The flag is tested prior to committing to transmit on mlx5e_xdp_xmit, and
it is sufficient to determine if it safe to transmit or not. The other
two internal flags (MLX5E_STATE_OPENED and MLX5E_SQ_STATE_ENABLED) become
unnecessary. Thus, they are removed from data path.
Fixes: 58b99ee3e3 ("net/mlx5e: Add support for XDP_REDIRECT in device-out side")
Reported-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Eliminate the following compilation warning:
drivers/net/ethernet/mellanox/mlx5/core/events.c: warning: 'error_str'
may be used uninitialized in this function [-Wuninitialized]: => 238:3
Fixes: c2fb3db22d ("net/mlx5: Rework handling of port module events")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Mikhael Goikhman <migo@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When EEH is injected and PCI bus stalls, mlx5's pci error detect
function is called to deactivate the command interface and tear down
the device. The issue is that there can be a thread that already
passed MLX5_DEVICE_STATE_INTERNAL_ERROR check, it will send the command
and stuck in the wait_func.
Solution:
Add function mlx5_cmd_flush to disable command interface and clear all
the pending commands. When device state is set to
MLX5_DEVICE_STATE_INTERNAL_ERROR, call mlx5_cmd_flush to ensure all
pending threads waiting for firmware commands completion are terminated.
Fixes: c1d4d2e92a ("net/mlx5: Avoid calling sleeping function by the health poll thread")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
New channels are applied to the priv channels only after they
are successfully opened. Then, the indirection table should be built
according to the new number of channels.
Currently, such build is preformed independently of whether the
channels opening is successful, and is not reverted on failure.
The bug is caused due to removal of rss params from channels struct
and moving it to priv struct. That change cause to independency between
channels and rss params.
This causes a crash on a later point, when accessing rqn of a non
existing channel.
This patch fixes it by moving the indirection table build right before
switching the priv channels to new channels struct, after the new set of
channels was successfully opened.
Fixes: bbeb53b8b2 ("net/mlx5e: Move RSS params to a dedicated struct")
Signed-off-by: Maria Pasechnik <mariap@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The current opt_inst_list operations inside team_nl_cmd_options_set()
is too complex to track:
LIST_HEAD(opt_inst_list);
nla_for_each_nested(...) {
list_for_each_entry(opt_inst, &team->option_inst_list, list) {
if (__team_option_inst_tmp_find(&opt_inst_list, opt_inst))
continue;
list_add(&opt_inst->tmp_list, &opt_inst_list);
}
}
team_nl_send_event_options_get(team, &opt_inst_list);
as while we retrieve 'opt_inst' from team->option_inst_list, it could
be added to the local 'opt_inst_list' for multiple times. The
__team_option_inst_tmp_find() doesn't work, as the setter
team_mode_option_set() still calls team->ops.exit() which uses
->tmp_list too in __team_options_change_check().
Simplify the list operations by moving the 'opt_inst_list' and
team_nl_send_event_options_get() into the nla_for_each_nested() loop so
that it can be guranteed that we won't insert a same list entry for
multiple times. Therefore, __team_option_inst_tmp_find() can be removed
too.
Fixes: 4fb0534fb7 ("team: avoid adding twice the same option to the event list")
Fixes: 2fcdb2c9e6 ("team: allow to send multiple set events in one message")
Reported-by: syzbot+4d4af685432dc0e56c91@syzkaller.appspotmail.com
Reported-by: syzbot+68ee510075cf64260cc4@syzkaller.appspotmail.com
Cc: Jiri Pirko <jiri@resnulli.us>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix race condition between ena_update_on_link_change() and
ena_restore_device().
This race can occur if link notification arrives while the driver
is performing a reset sequence. In this case link can be set up,
enabling the device, before it is fully restored. If packets are
sent at this time, the driver might access uninitialized data
structures, causing kernel crash.
Move the clearing of ENA_FLAG_ONGOING_RESET and netif_carrier_on()
after ena_up() to ensure the device is ready when link is set up.
Fixes: d18e4f6834 ("net: ena: fix race condition between device reset and link up setup")
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, it is not guaranteed. For example, switches might
choose to make other use of these octets.
This repeatedly causes kernel hardware checksum fault.
Prior to the cited commit below, skb checksum was forced to be
CHECKSUM_NONE when padding is detected. After it, we need to keep
skb->csum updated. However, fixing up CHECKSUM_COMPLETE requires to
verify and parse IP headers, it does not worth the effort as the packets
are so small that CHECKSUM_COMPLETE has no significant advantage.
Future work: when reporting checksum complete is not an option for
IP non-TCP/UDP packets, we can actually fallback to report checksum
unnecessary, by looking at cqe IPOK bit.
Fixes: 88078d98d1 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During testing on Armada 388 platforms, it was found with a certain
module configuration that it was possible to trigger a kernel oops
during the module load process, caused by the phylink resolver being
triggered for a currently disabled interface.
This problem was introduced by changing the way the SFP registration
works, which now can result in the sfp link down notification being
called during phylink_create().
Fixes: b5bfc21af5 ("net: sfp: do not probe SFP module before we're attached")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the depends on NET_UDP_TUNNEL, at the moment it is impossible to
compile GENEVE if no other protocol depending on NET_UDP_TUNNEL is
selected.
Fix this changing the depends to a select, and drop NET_IP_TUNNEL from the
select list, as it already depends on NET_UDP_TUNNEL.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reviewed-and-tested-by: Andrea Claudi <aclaudi@redhat.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitmap of found partitions in efx_ef10_mtd_probe was not
initialised, causing partitions to be suppressed based off whatever
value was in the bitmap at the start.
Fixes: 3366463513 ("sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe")
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_rx() must be called under a strict contract.
At device dismantle phase, core networking clears IFF_UP
and flush_all_backlogs() is called after rcu grace period
to make sure no incoming packet might be in a cpu backlog
and still referencing the device.
Most drivers call netif_rx() from their interrupt handler,
and since the interrupts are disabled at device dismantle,
netif_rx() does not have to check dev->flags & IFF_UP
Virtual drivers do not have this guarantee, and must
therefore make the check themselves.
Otherwise we risk use-after-free and/or crashes.
Note this patch also fixes a small issue that came
with commit ce6502a8f9 ("vxlan: fix a use after free
in vxlan_encap_bypass"), since the dev->stats.rx_dropped
change was done on the wrong device.
Fixes: d342894c5d ("vxlan: virtual extensible lan")
Fixes: ce6502a8f9 ("vxlan: fix a use after free in vxlan_encap_bypass")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petr Machata <petrm@mellanox.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Roopa Prabhu <roopa@cumulusnetworks.com>
Cc: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 2e6eedb481.
Sander reported a regression causing a kernel panic[1],
therefore let's revert this commit.
[1] https://marc.info/?t=154965066400001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bd7153bd83.
There doesn't seem to be anything wrong with this patch,
it's just reverted to get a stable baseline again.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we probe a SFP module, we expect to be able to call the upstream
device's module_insert() function so that the upstream link can be
configured. However, when the upstream device is delayed, we currently
may end up probing the module before the upstream device is available,
and lose the module_insert() call.
Avoid this by holding off probing the module until the SFP bus is
properly connected to both the SFP socket driver and the upstream
driver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.
Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.
Fixes: 16994374a6 ("net: dsa: b53: Make SRAB driver manage port interrupts")
Fixes: b2ddc48a81 ("net: dsa: b53: Do not fail when IRQ are not initialized")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we add a new GENEVE device with IPv6 remote, checking only for
IS_ENABLED(CONFIG_IPV6) is not enough as we may disable IPv6 in the
kernel command line (ipv6.disable=1), and calling rt6_lookup() would
cause a NULL pointer dereference.
v2:
- don't mix declarations and code (reported by Stefano Brivio, Eric Dumazet)
- there's no need to use in6_dev_get() as we only need to check that
idev exists (reported by David Ahern). This is under RTNL, so we can
simply use __in6_dev_get() instead (Stefano, Eric).
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: c40e89fd35 ("geneve: configure MTU based on a lower device")
Cc: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
8c56df372b ("net: add support for Cavium PTP coprocessor") added the
Cavium PTP coprocessor driver and enabled it by default. Remove the
"default y" because the driver only applies to Cavium ThunderX processors.
Fixes: 8c56df372b ("net: add support for Cavium PTP coprocessor")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in sbdma_tx_process() when
skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in velocity_free_tx_buf()
when skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in bdx_tx_cleanup() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in hdlc_tx_done() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in mpc52xx_fec_tx_interrupt()
when skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in epic_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in dscc4_tx_irq() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in de_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in dfx_xmt_done() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some case, we may use multiple pedit actions to modify packets.
The command shown as below: the last pedit action is effective.
$ tc filter add dev netdev_rep parent ffff: protocol ip prio 1 \
flower skip_sw ip_proto icmp dst_ip 3.3.3.3 \
action pedit ex munge ip dst set 192.168.1.100 pipe \
action pedit ex munge eth src set 00:00:00:00:00:01 pipe \
action pedit ex munge eth dst set 00:00:00:00:00:02 pipe \
action csum ip pipe \
action tunnel_key set src_ip 1.1.1.100 dst_ip 1.1.1.200 dst_port 4789 id 100 \
action mirred egress redirect dev vxlan0
To fix it, we add max_mod_hdr_actions to mlx5e_tc_flow_parse_attr struction,
max_mod_hdr_actions will store the max pedit action number we support and
num_mod_hdr_actions indicates how many pedit action we used, and store all
pedit action to mod_hdr_actions.
Fixes: d79b6df6b1 ("net/mlx5e: Add parsing of TC pedit actions to HW format")
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we offload tc filters to hardware, hardware flows can
be updated when mac of encap destination ip is changed.
But we ignore one case, that the mac of local encap ip can
be changed too, so we should also update them.
To fix it, add route_dev in mlx5e_encap_entry struct to save
the local encap netdevice, and when mac changed, kernel will
flush all the neighbour on the netdevice and send NETEVENT_NEIGH_UPDATE
event. The mlx5 driver will delete the flows and add them when neighbour
available again.
Fixes: 232c001398 ("net/mlx5e: Add support to neighbour update flow")
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Version update for qed/qede modules.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unnecessary logging of message in an expected
default case where coalescing value read (via ethtool -c)
migh not be valid unless they are configured explicitly
in the hardware using ethtool -C.
Signed-off-by: Rahul Verma <rverma@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy traffic load, when changing number of channels via
ethtool (ethtool -L) which will cause interface to be reloaded,
it was observed that some packets gets transmitted on old TX
channel/queue id which doesn't really exist after the channel
configuration leads to system crash.
Add a safeguard in the driver by validating queue id through
ndo_select_queue() which is called before the ndo_start_xmit().
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
