Add support for 802.1ad including the ability to push and pop double
tagged vlans. Add support for 802.1ad to netlink parsing and flow
conversion. Uses double nested encap attributes to represent double
tagged vlan. Inner TPID encoded along with ctci in nested attributes.
This is based on Thomas F Herbert's original v20 patch. I made some
small clean ups and bug fixes.
Signed-off-by: Thomas F Herbert <thomasfherbert@gmail.com>
Signed-off-by: Eric Garver <e@erig.me>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Lennert the MPLS GSO code is failing to properly segment
large packets. There are a couple of problems:
1. the inner protocol is not set so the gso segment functions for inner
protocol layers are not getting run, and
2 MPLS labels for packets that use the "native" (non-OVS) MPLS code
are not properly accounted for in mpls_gso_segment.
The MPLS GSO code was added for OVS. It is re-using skb_mac_gso_segment
to call the gso segment functions for the higher layer protocols. That
means skb_mac_gso_segment is called twice -- once with the network
protocol set to MPLS and again with the network protocol set to the
inner protocol.
This patch sets the inner skb protocol addressing item 1 above and sets
the network_header and inner_network_header to mark where the MPLS labels
start and end. The MPLS code in OVS is also updated to set the two
network markers.
>From there the MPLS GSO code uses the difference between the network
header and the inner network header to know the size of the MPLS header
that was pushed. It then pulls the MPLS header, resets the mac_len and
protocol for the inner protocol and then calls skb_mac_gso_segment
to segment the skb.
Afterward the inner protocol segmentation is done the skb protocol
is set to mpls for each segment and the network and mac headers
restored.
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds a new OVS action, OVS_ACTION_ATTR_TRUNC, in order to
truncate packets. A 'max_len' is added for setting up the maximum
packet size, and a 'cutlen' field is to record the number of bytes
to trim the packet when the packet is outputting to a port, or when
the packet is sent to userspace.
Signed-off-by: William Tu <u9012063@gmail.com>
Cc: Pravin Shelar <pshelar@nicira.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of CHECKSUM_COMPLETE the skb checksum should be updated in
{push,pop}_mpls() as they the type in the ethernet header.
As suggested by Pravin Shelar.
Cc: Pravin Shelar <pshelar@nicira.com>
Fixes: 25cd9ba0ab ("openvswitch: Add basic MPLS support to kernel")
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using masked actions the ipv6_proto field of an action
to set IPv6 fields may be zero rather than the prevailing protocol
which will result in skipping checksum recalculation.
This patch resolves the problem by relying on the protocol
in the flow key rather than that in the set field action.
Fixes: 83d2b9ba1a ("net: openvswitch: Support masked set actions.")
Cc: Jarno Rajahalme <jrajahalme@nicira.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace individual implementations with the recently introduced
skb_postpush_rcsum() helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Tom Herbert <tom@herbertland.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was seen that defective configurations of openvswitch could overwrite
the STACK_END_MAGIC and cause a hard crash of the kernel because of too
many recursions within ovs.
This problem arises due to the high stack usage of openvswitch. The rest
of the kernel is fine with the current limit of 10 (RECURSION_LIMIT).
We use the already existing recursion counter in ovs_execute_actions to
implement an upper bound of 5 recursions.
Cc: Pravin Shelar <pshelar@ovn.org>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ip_defrag() returns an error other than -EINPROGRESS, then the skb is
freed. When handle_fragments() passes this back up to
do_execute_actions(), it will be freed again. Prevent this double free
by never freeing the skb in do_execute_actions() for errors returned by
ovs_ct_execute. Always free it in ovs_ct_execute() error paths instead.
Fixes: 7f8a436eaa ("openvswitch: Add conntrack action")
Reported-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
While transitioning to netdev based vport we broke OVS
feature which allows user to retrieve tunnel packet egress
information for lwtunnel devices. Following patch fixes it
by introducing ndo operation to get the tunnel egress info.
Same ndo operation can be used for lwtunnel devices and compat
ovs-tnl-vport devices. So after adding such device operation
we can remove similar operation from ovs-vport.
Fixes: 614732eaa1 ("openvswitch: Use regular VXLAN net_device device").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ct action uses parts of the flow key, so we need to ensure that it
is valid before executing that action.
Fixes: 7f8a436eaa "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ovs_fragment() was unable to fragment the skb due to an L2 header
that exceeds the supported length, skbs would be leaked. Fix the bug.
Fixes: 7f8a436eaa "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conntrack LABELS (plural) are exposed by conntrack; rename the OVS name
for these to be consistent with conntrack.
Fixes: c2ac667 "openvswitch: Allow matching on conntrack label"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was a compatibility function needed while the ipv4 and ipv6
fragmentation code was being modified to pass a struct net through
them. Now that is complete this function has no more users so remove
it.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
In preparation for the ipv4 and ipv6 fragmentation code taking a net
parameter pass a struct net into ovs_fragment where the v4 and v6
fragmentation code is called.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
When struct net starts being passed through the ipv4 and ipv6 fragment
routines ovs_vport_output will need to take a net parameter.
Prepare ovs_vport_output before that is needed and introduce
ovs_vport_output_skk for the call sites that still need the old
calling conventions.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Currently tun-info options pointer is used in few cases to
pass options around. But tunnel options can be accessed using
ip_tunnel_info_opts() API without using the pointer. Following
patch removes the redundant pointer and consistently make use
of API.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tun info is passed using skb-dst pointer. Now we have
converted all vports to netdev based implementation so
Now we can remove redundant pointer to tun-info from OVS_CB.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot reports that certain configurations will not
automatically pick up on the "struct rt6_info" definition, so explicitly
include the header for this structure.
Fixes: 7f8a436 "openvswitch: Add conntrack action"
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow matching and setting the ct_label field. As with ct_mark, this is
populated by executing the CT action. The label field may be modified by
specifying a label and mask nested under the CT action. It is stored as
metadata attached to the connection. Label modification occurs after
lookup, and will only persist when the conntrack entry is committed by
providing the COMMIT flag to the CT action. Labels are currently fixed
to 128 bits in size.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow matching and setting the ct_mark field. As with ct_state and
ct_zone, these fields are populated when the CT action is executed. To
write to this field, a value and mask can be specified as a nested
attribute under the CT action. This data is stored with the conntrack
entry, and is executed after the lookup occurs for the CT action. The
conntrack entry itself must be committed using the COMMIT flag in the CT
action flags for this change to persist.
Signed-off-by: Justin Pettit <jpettit@nicira.com>
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the kernel connection tracker via OVS. Userspace components can
make use of the CT action to populate the connection state (ct_state)
field for a flow. This state can be subsequently matched.
Exposed connection states are OVS_CS_F_*:
- NEW (0x01) - Beginning of a new connection.
- ESTABLISHED (0x02) - Part of an existing connection.
- RELATED (0x04) - Related to an established connection.
- INVALID (0x20) - Could not track the connection for this packet.
- REPLY_DIR (0x40) - This packet is in the reply direction for the flow.
- TRACKED (0x80) - This packet has been sent through conntrack.
When the CT action is executed by itself, it will send the packet
through the connection tracker and populate the ct_state field with one
or more of the connection state flags above. The CT action will always
set the TRACKED bit.
When the COMMIT flag is passed to the conntrack action, this specifies
that information about the connection should be stored. This allows
subsequent packets for the same (or related) connections to be
correlated with this connection. Sending subsequent packets for the
connection through conntrack allows the connection tracker to consider
the packets as ESTABLISHED, RELATED, and/or REPLY_DIR.
The CT action may optionally take a zone to track the flow within. This
allows connections with the same 5-tuple to be kept logically separate
from connections in other zones. If the zone is specified, then the
"ct_zone" match field will be subsequently populated with the zone id.
IP fragments are handled by transparently assembling them as part of the
CT action. The maximum received unit (MRU) size is tracked so that
refragmentation can occur during output.
IP frag handling contributed by Andy Zhou.
Based on original design by Justin Pettit.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Signed-off-by: Justin Pettit <jpettit@nicira.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow the ovs-conntrack code to reuse these macros.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_proto_csum_replace4,2,16 take a pseudohdr argument which indicates
the checksum field carries a pseudo header. This argument should be a
boolean instead of an int.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When sampling rate is 1, the sampling probability is UINT32_MAX. The packet
should be sampled even the prandom32() generate the number of UINT32_MAX.
And none packet need be sampled when the probability is 0.
Signed-off-by: Wenyu Zhang <wenyuz@vmware.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
openvswitch modifies the L4 checksum of a packet when modifying
the ip address. When an IP packet is fragmented only the first
fragment contains an L4 header and checksum. Prior to this change
openvswitch would modify all fragments, modifying application data
in non-first fragments, causing checksum failures in the
reassembled packet.
Signed-off-by: Glenn Griffin <ggriffin.kernel@gmail.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the new metadata dst to attach encapsulation instructions to
the skb. The existing egress_tun_info via the OVS_CB() is left in
place until all tunnel vports have been converted to the new method.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the tunnel metadata data structures currently internal to
OVS and make them generic for use by all IP tunnels.
Both structures are kernel internal and will stay that way. Their
members are exposed to user space through individual Netlink
attributes by OVS. It will therefore be possible to extend/modify
these structures without affecting user ABI.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If new optional attribute OVS_USERSPACE_ATTR_ACTIONS is added to an
OVS_ACTION_ATTR_USERSPACE action, then include the datapath actions
in the upcall.
This Directly associates the sampled packet with the path it takes
through the virtual switch. Path information currently includes mangling,
encapsulation and decapsulation actions for tunneling protocols GRE,
VXLAN, Geneve, MPLS and QinQ, but this extension requires no further
changes to accommodate datapath actions that may be added in the
future.
Adding path information enhances visibility into complex virtual
networks.
Signed-off-by: Neil McKee <neil.mckee@inmon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OVS userspace already probes the openvswitch kernel module for
OVS_ACTION_ATTR_SET_MASKED support. This patch adds the kernel module
implementation of masked set actions.
The existing set action sets many fields at once. When only a subset
of the IP header fields, for example, should be modified, all the IP
fields need to be exact matched so that the other field values can be
copied to the set action. A masked set action allows modification of
an arbitrary subset of the supported header bits without requiring the
rest to be matched.
Masked set action is now supported for all writeable key types, except
for the tunnel key. The set tunnel action is an exception as any
input tunnel info is cleared before action processing starts, so there
is no tunnel info to mask.
The kernel module converts all (non-tunnel) set actions to masked set
actions. This makes action processing more uniform, and results in
less branching and duplicating the action processing code. When
returning actions to userspace, the fully masked set actions are
converted back to normal set actions. We use a kernel internal action
code to be able to tell the userspace provided and converted masked
set actions apart.
Signed-off-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPLS GSO needs to know inner most protocol to process GSO packets.
Fixes: 25cd9ba0ab ("openvswitch: Add basic MPLS support to
kernel").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ieee802154/fakehard.c
A bug fix went into 'net' for ieee802154/fakehard.c, which is removed
in 'net-next'.
Add build fix into the merge from Stephen Rothwell in openvswitch, the
logging macros take a new initial 'log' argument, a new call was added
in 'net' so when we merge that in here we have to explicitly add the
new 'log' arg to it else the build fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
So it can be used from out of openvswitch code.
Did couple of cosmetic changes on the way, namely variable naming and
adding support for 8021AD proto.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
note that skb_make_writable already exists in net/netfilter/core.c
but does something slightly different.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Name fits better. Plus there's going to be introduced
__vlan_insert_tag later on.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace duplicated code by calling skb_postpull_rcsum
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The checksum of ICMPv6 packets uses the IP pseudoheader as part of
the calculation, unlike ICMP in IPv4. This was not implemented,
which means that modifying the IP addresses of an ICMPv6 packet
would cause the checksum to no longer be correct as the psuedoheader
did not match.
Introduced by commit 3fdbd1ce11 ("openvswitch: add ipv6 'set' action").
Reported-by: Neal Shrader <icosahedral@gmail.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Need to free memory in case of sample action error.
Introduced by commit 651887b0c2 ("openvswitch: Sample
action without side effects").
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
struct dp_upcall_info has pointer to pkt_key which is already
available in OVS_CB. This also simplifies upcall handling
for gso packet.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
OVS need to flow key for flow lookup in recic action. OVS
does key extract in recic action. Most of cases we could
use OVS_CB packet key directly and can avoid packet flow key
extract. SET action we can update flow-key along with packet
to keep it consistent. But there are some action like MPLS
pop which forces OVS to do flow-extract. In such cases we
can mark flow key as invalid so that subsequent recirc
action can do full flow extract.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Jarno Rajahalme <jrajahalme@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
OVS vswitch has extended IPFIX exporter to export tunnel headers
to improve network visibility.
To export this information userspace needs to know egress tunnel
for given packet. By extending packet attributes datapath can
export egress tunnel info for given packet. So that userspace
can ask for egress tunnel info in userspace action. This
information is used to build IPFIX data for given flow.
Signed-off-by: Wenyu Zhang <wenyuz@vmware.com>
Acked-by: Romain Lenglet <rlenglet@vmware.com>
Acked-by: Ben Pfaff <blp@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
The 'flow' memeber was chosen for removal because it's only used
in ovs_execute_actions() we can pass it as argument to this
function.
Signed-off-by: Lorand Jakab <lojakab@cisco.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
skb_clone() NULL check is implemented in do_output(), as past of the
common (fast) path. Refactoring so that NULL check is done in the
slow path, immediately after skb_clone() is called.
Besides optimization, this change also improves code readability by
making the skb_clone() NULL check consistent within OVS datapath
module.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
