Use the generic facility instead of a home-grown one.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Convert dprintk to netdev_dbg where appropriate.
Remove dvb_net_debug module_param.
Remove __func__ from output as that can be added by dynamic_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
No need for more macros, so remove them and use the kernel extension.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Needed due to some important regression fixes at RC core.
* commit 'v3.18-rc4': (587 commits)
Linux 3.18-rc4
ARM: dts: zynq: Enable PL clocks for Parallella
tiny: rename ENABLE_DEV_COREDUMP to ALLOW_DEV_COREDUMP
tiny: reverse logic for DISABLE_DEV_COREDUMP
i2c: core: Dispose OF IRQ mapping at client removal time
i2c: at91: don't account as iowait
i2c: remove FSF address
USB: Update default usb-storage delay_use value in kernel-parameters.txt
sysfs: driver core: Fix glue dir race condition by gdp_mutex
MIPS: Fix build with binutils 2.24.51+
xfs: track bulkstat progress by agino
xfs: bulkstat error handling is broken
xfs: bulkstat main loop logic is a mess
xfs: bulkstat chunk-formatter has issues
xfs: bulkstat chunk formatting cursor is broken
xfs: bulkstat btree walk doesn't terminate
mm: Fix comment before truncate_setsize()
USB: cdc-acm: add quirk for control-line state requests
tty: Fix pty master poll() after slave closes v2
MIPS: R3000: Fix debug output for Virtual page number
...
Conflicts:
drivers/media/rc/rc-main.c
It's better to use TS_SC instead of magic number 0xC0.
[m.chehab@samsung.com: patch rebased and message rewritten, as this
patch conflicted with an already applied patch]
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
Add parentheses around the mask.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add support for IT930x USB bridge and IT9303 reference design.
It is a DVB-T/T2/C tuner with the following components:
- IT9303 USB bridge
- Si2168-B40 demodulator
- Si2147-A30 tuner
The IT9303 requires firmware that can be downloaded here:
http://trsqr.net/olli/linux/firmwares/it930x/
The Si2168-B40 requires firmware, but the one that is used by PCTV 292e can be used.
http://palosaari.fi/linux/v4l-dvb/firmware/Si2168/Si2168-B40/
The Si2147-A30 tuner does not require firmware loading.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
There are some patches that depends on media-v3.16-rc6.
So, merge back from upstream before applying them.
* linus/master: (1123 commits)
drm/nouveau: ltc/gf100-: fix cbc issues on certain boards
drm/bochs: add missing drm_connector_register call
drm/cirrus: add missing drm_connector_register call
staging: vt6655: buffer overflow in ioctl
USB: storage: Add quirks for Entrega/Xircom USB to SCSI converters
USB: storage: Add quirk for Ariston Technologies iConnect USB to SCSI adapter
USB: storage: Add quirk for Adaptec USBConnect 2000 USB-to-SCSI Adapter
USB: EHCI: unlink QHs even after the controller has stopped
[SCSI] fix for bidi use after free
[SCSI] fix regression that accidentally disabled block-based tcq
[SCSI] libiscsi: fix potential buffer overrun in __iscsi_conn_send_pdu
drm/radeon: Fix typo 'addr' -> 'entry' in rs400_gart_set_page
drm/nouveau/runpm: fix module unload
drm/radeon/px: fix module unload
vgaswitcheroo: add vga_switcheroo_fini_domain_pm_ops
drm/radeon: don't reset dma on r6xx-evergreen init
drm/radeon: don't reset sdma on CIK init
drm/radeon: don't reset dma on NI/SI init
drm/radeon/dpm: fix resume on mullins
drm/radeon: Disable HDP flush before every CS again for < r600
...
Sparse is complaining about ngene's bad usage of a __user ptr:
>> drivers/media/pci/ngene/ngene-dvb.c:62:48: sparse: incorrect type in argument 2 (different address spaces)
drivers/media/pci/ngene/ngene-dvb.c:62:48: expected unsigned char const [usertype] *buf
drivers/media/pci/ngene/ngene-dvb.c:62:48: got char const [noderef] <asn:1>*buf
As this is intercepting a .write() file ops, we can't just memcpy. We need to use
copy_from_user.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
add the following IDs
USB_PID_PCTV_78E (0x025a) for PCTV 78e
USB_PID_PCTV_79E (0x0262) for PCTV 79e
For these it9135 devices.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: Antti Palosaari <crope@iki.fi>
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by smatch:
drivers/media/dvb-core/dmxdev.c:1091 dvb_demux_poll() warn: variable dereferenced before check 'dmxdevfilter' (see line 1088)
This was introduced by changeset d102cac809.
We need to test before using it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
TechnoTrend TT-connect CT2-4650 CI (0b48:3012) is an USB DVB-T2/C tuner with
the following components:
USB interface: Cypress CY7C68013A-56LTXC
Demodulator: Silicon Labs Si2168-A20
Tuner: Silicon Labs Si2158-A20
CI chip: CIMaX SP2HF
The firmware for the tuner is the same as for TechnoTrend TT-TVStick CT2-4400.
See https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html
The demodulator needs a firmware that can be extracted from the Windows drivers.
File ttConnect4650_64.sys should be extracted from
http://www.tt-downloads.de/bda-treiber_4.1.0.4.zip (MD5 sum below).
3464bfc37a47b4032568718bacba23fb ttConnect4650_64.sys
Then the firmware can be extracted:
dd if=ttConnect4650_64.sys ibs=1 skip=273376 count=6424 of=dvb-demod-si2168-a20-01.fw
The SP2 CI module requires a definition of a function cxusb_tt_ct2_4650_ci_ctrl
that is passed on to the SP2 driver and called back for CAM operations.
[crope@iki.fi: meld USB ID define patch to this]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
when usb-type tuner is pulled out, user applications did not close device's FD,
and go on polling the device, we should return POLLERR directly.
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Data type of return value is unsigned int, but in function of dvb_demux_poll,
when the pointer of dmxdevfilter equals NULL, it will return -EINVAL, which
is invalid.
Signed-off-by: Changbing Xiong <cb.xiong@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The needed bandwidth can be estimated using the symbol rate and
the rolloff factor. This could be useful for the frontend drivers,
as they don't need to calculate it themselves.
Reported-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
While several tuners have some sort of suspend/resume
implementation, this is currently mangled with an optional
.sleep callback that it is also used to put the device on
low power mode.
Not all drivers implement it, as returning the driver from
low power may require to re-load the firmware, with takes
some time. Also, some drivers may delay it.
So, the more coherent is to add two new optional callbacks
that will let the tuners to directy implement suspend and
resume callbacks if they need.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
Some fe drivers will have to do additional initialization
in their fe ops.init interfaces when called during resume.
Without the additional initialization, fe and tuner driver
resume fails. A new fe exit flag value DVB_FE_DEVICE_RESUME
is necessary to detect resume case. This patch adds a new
define and changes dvb_frontend_resume() to set it prior to
calling fe init and tuner init calls and resets it back to
DVB_FE_NO_EXIT once fe and tuner init is done.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some fe drivers attempt to access the device for power control from
their release routines. When release routines are called after device
is disconnected, the attempts fail. fe drivers should avoid accessing
the device, from their release interfaces when called from disconnect
path. dvb-frontend maintains exit flag to keep track when fe device is
disconnected in its private data structures. Export the flag in fe to
enable drivers to check the device status from their release interfaces.
Signed-off-by: Shuah Khan <shuah.kh@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Added Sveon STV21 device based on Realtek RTL2832U and FC0013 tuner
Signed-off-by: Sebastian Kemper <sebastian_ml@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
USB ID 0b48:3014.
USB interface: Cypress CY7C68013A-56LTXC
Demodulator: Silicon Labs Si2168-30
Tuner: Silicon Labs Si2158-20
Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Michael Ira Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The dvb_attach() was unbalanced, as there was no dvb_dettach. Ok,
on current cases, the dettach is done by dvbdev, but that are some
future corner cases where we may need to do this before registering
the frontend.
So, add a dvb_detach() and use it at dvb_frontend.c.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is another clone of AZ6027. This patch adds the relevant PID.
Signed-off-by: Manuel Schönlaub <manuel.schoenlaub@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Check if index is within bounds _before_ accessing the value.
Signed-off-by: Ole Ernst <olebowle@gmx.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If an attempt to set LNA fails, restore the cache to LNA_AUTO,
in order to make it to reflect the current LNA status.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I've got the following DAB USB stick that also works fine with the
DVB_USB_RTL28XXU driver after I added its USB ID:
Bus 001 Device 009: ID 0ccd:00b4 TerraTec Electronic GmbH
[crope@iki.fi: apply patch partly manually]
Signed-off-by: Till Dörges <till@doerges.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
- a new jpeg codec driver for Samsung Exynos (jpeg-hw-exynos4)
- a new dvb frontend for ds2103 chipset (m88ds2103)
- a new sensor driver for Samsung S5K5BAF UXGA (s5k5baf)
- new drivers for R-Car VSP1
- a new radio driver: radio-raremono
- a new tuner driver for ts2022 chipset (m88ts2022)
- the analog part of em28xx is now a separate module that only
load/runs if the device is not a pure digital TV device
- added a staging driver for bcm2048 radio devices
- the omap 2 video driver (omap24xx) was moved to staging. This driver
is for an old hardware and uses a deprecated Kernel internal API. If
nobody cares enough to fix it, it would be removed on a couple Kernel
releases
- the sn9c102 driver was moved to staging. This driver was replaced by
gspca, and disabled on some distros, as almost all devices are known
to work properly with gspca. It should be removed from kernel on a
couple Kernel releases
- lots of driver fixes, improvements and cleanups
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (421 commits)
[media] media: v4l2-dev: fix video device index assignment
[media] rc-core: reuse device numbers
[media] em28xx-cards: properly initialize the device bitmap
[media] Staging: media: Fix line length exceeding 80 characters in as102_drv.c
[media] Staging: media: Fix line length exceeding 80 characters in as102_fe.c
[media] Staging: media: Fix quoted string split across line in as102_fe.c
[media] media: st-rc: Add reset support
[media] m2m-deinterlace: fix allocated struct type
[media] radio-usb-si4713: fix sparse non static symbol warnings
[media] em28xx-audio: remove needless check before usb_free_coherent()
[media] au0828: Fix sparse non static symbol warning
Revert "[media] go7007-usb: only use go->dev after allocated"
[media] em28xx-audio: provide an error code when URB submit fails
[media] em28xx: fix check for audio only usb interfaces when changing the usb alternate setting
[media] em28xx: fix usb alternate setting for analog and digital video endpoints > 0
[media] em28xx: make 'em28xx_ctrl_ops' static
em28xx-alsa: Fix error patch for init/fini
[media] em28xx-audio: flush work at .fini
[media] drxk: remove the option to load firmware asynchronously
[media] em28xx: adjust period size at runtime
...
Use possibly more efficient ether_addr_equal
instead of memcmp.
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: linux-media@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GIT_AUTHOR_DATE=1386943312
Add USB IDs for the WinFast DTV Dongle Mini.
Device is tested and works fine under MythTV
Signed-off-by: Robert Backhaus <robbak@robbak.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Merge the media fixes merged upstream for v3.13-rc4
* upstream-fixes: (30 commits)
[media] videobuf2-dma-sg: fix possible memory leak
[media] vb2: regression fix: always set length field.
[media] mt9p031: Include linux/of.h header
[media] rtl2830: add parent for I2C adapter
[media] media: marvell-ccic: use devm to release clk
[media] ths7303: Declare as static a private function
[media] em28xx-video: Swap release order to avoid lock nesting
[media] usbtv: Add support for PAL video source
[media] media_tree: Fix spelling errors
[media] videobuf2: Add support for file access mode flags for DMABUF exporting
[media] radio-shark2: Mark shark_resume_leds() inline to kill compiler warning
[media] radio-shark: Mark shark_resume_leds() inline to kill compiler warning
[media] af9035: unlock on error in af9035_i2c_master_xfer()
[media] af9033: fix broken I2C
[media] v4l: omap3isp: Don't check for missing get_fmt op on remote subdev
[media] af9035: fix broken I2C and USB I/O
[media] wm8775: fix broken audio routing
[media] marvell-ccic: drop resource free in driver remove
[media] tef6862/radio-tea5764: actually assign clamp result
[media] cx231xx: use after free on error path in probe
...
This is similar to the Terratec H7. It works with the same az6007 firmware as
the former, however the drx-k firmware of the H7 will NOT work. Hence use
a different firmware name. The firmware does not need to exist as the one in
the eeprom is just fine as long as the h7 one doesn't get loaded, but maybe
some day someone wants to load it (the one from the h5 would work too).
Also since the config entry is now different anyway disable support for rc.
AFAIK the Technisat remote (TS35) is RC5 and the code (which a code comment
claims doesn't work anyway) only would handle NEC hence it's pointless creating
a device and polling it if we already know it can't work.
CI is untested.
Originally based on idea found on
http://www.linuxtv.org/wiki/index.php/TechniSat_CableStar_Combo_HD_CI claiming
only id needs to be added (but failed to mention it only worked because the
driver couldn't find the h7 drx-k firmware...).
Signed-off-by: Roland Scheidegger <rscheidegger_lists@hispeed.ch>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Fix various spelling errors in strings and comments throughout the media
tree. The majority of these were found using Lucas De Marchi's codespell
tool.
[m.chehab@samsung.com: discard hunks with conflicts]
Signed-off-by: Jonathan McCrohan <jmccrohan@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
removes trailing whitespace and rebalance line length in comment block
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
dmx_section_feed_release_filter() locks dvbdmx->mutex and
if the feed is still filtering, it calls feed->stop_filtering(feed).
stop_filtering() is implemented by dmx_section_feed_stop_filtering()
that first of all try to lock the same mutex: dvbdmx->mutex.
That leads to a deadlock.
It does not happen often in practice because all callers of
release_filter() stop filtering by themselves.
So the problem can happen in case of race condition only.
The patch releases dvbdmx->mutex before call to feed->stop_filtering(feed)
and reacquires the mutex after that.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"This series include:
- a new Remote Controller driver for ST SoC with the corresponding DT
bindings
- a new frontend (cx24117)
- a new I2C camera flash driver (lm3560)
- a new mem2mem driver for TI SoC (ti-vpe)
- support for Raphael r828d added to r820t driver
- some improvements on buffer allocation at VB2 core
- usual driver fixes and improvements
PS this time, we have a smaller number of patches. While it is hard
to pinpoint to the reasons, I believe that it is mainly due to:
1) there are several patch series ready, but depending on DT review.
I decided to grant some extra time for DT maintainers to look on
it, as they're expecting to have more time with the changes agreed
during ARM mini-summit and KS. If they can't review in time for
3.14, I'll review myself and apply for the next merge window.
2) I suspect that having both LinuxCon EU and LinuxCon NA happening
during the same merge window affected the development
productivity, as several core media developers participated on
both events"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (151 commits)
[media] media: st-rc: Add ST remote control driver
[media] gpio-ir-recv: Include linux/of.h header
[media] tvp7002: Include linux/of.h header
[media] tvp514x: Include linux/of.h header
[media] ths8200: Include linux/of.h header
[media] adv7343: Include linux/of.h header
[media] v4l: Fix typo in v4l2_subdev_get_try_crop()
[media] media: i2c: add driver for dual LED Flash, lm3560
[media] rtl28xxu: add 15f4:0131 Astrometa DVB-T2
[media] rtl28xxu: add RTL2832P + R828D support
[media] rtl2832: add new tuner R828D
[media] r820t: add support for R828D
[media] media/i2c: ths8200: fix build failure with gcc 4.5.4
[media] Add support for KWorld UB435-Q V2
[media] staging/media: fix msi3101 build errors
[media] ddbridge: Remove casting the return value which is a void pointer
[media] ngene: Remove casting the return value which is a void pointer
[media] dm1105: remove unneeded not-null test
[media] sh_mobile_ceu_camera: remove deprecated IRQF_DISABLED
[media] media: rcar_vin: Add preliminary r8a7790 support
...
nobody else will see that struct file after return from ->release()
anyway; just leave ->f_op as is and let __fput() do that fops_put().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Complete() will be run with interrupt enabled, so change to
spin_lock_irqsave().
These functions may be called inside URB->complete(), so use
spin_lock_irqsave().
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
In dvb_ringbuffer lock-less synchronizationof reader and writer threads is done
with separateread and write pointers. Sincedvb_ringbuffer_flush() modifies the
read pointer, this function must not be called from the writer thread.
This patch removes the dvb_ringbuffer_flush() calls in the dmxdev ringbuffer
write functions, this fixes Oopses "Unable to handle kernel paging request"
I could observe for the call chaindvb_demux_read ->dvb_dmxdev_buffer_read ->
dvb_ringbuffer_read_user -> __copy_to_user (the reader side of the ringbuffer).
The flush calls at the write side are not necessary anyway since ringbuffer_flush
is also called in dvb_dmxdev_buffer_read() when an error condition is set in the
ringbuffer.
This patch should also be applied to stable kernels.
Signed-off-by: Soeren Moch <smoch@web.de>
CC: <stable@vger.kernel.org>
Reviewed-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The device has been tested on a MIPSel box with kernel 3.1.1 and backported media_tree drivers
The kernel detects the device with the following output:
usbcore: registered new interface driver dvb_usb_rtl28xxu
usb 1-2: dvb_usb_v2: found a 'Crypto Redi PC50A' in warm state
usb 1-2: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Crypto Redi PC50A)
usb 1-2: DVB: registering adapter 1 frontend 0 (Realtek RTL2832 (DVB-T))...
i2c i2c-4: fc0012: Fitipower FC0012 successfully identified
usb 1-2: dvb_usb_v2: 'Crypto Redi PC50A' successfully initialized and connected
[crope@iki.fi: fix trivial merge conflict]
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tested on a MIPSel box with 3.3.6 kernel
The kernel output when the device will be detected follows:
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=3 Tuner Type=38
it913x: Chip Version=01 Chip Type=9135
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in cold state
usb 2-1: dvb_usb_v2: downloading firmware from file 'dvb-usb-it9137-01.fw'
it913x: FRM Starting Firmware Download
it913x: FRM Firmware Download Completed - Resetting Device
it913x: Chip Version=01 Chip Type=9135
it913x: Firmware Version 204147968
usb 2-1: dvb_usb_v2: found a 'Digital Dual TV Receiver CTVDIGDUAL_V2' in warm state
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 1 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_1)...
usb 2-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the software demuxer
DVB: registering new adapter (Digital Dual TV Receiver CTVDIGDUAL_V2)
it913x-fe: ADF table value :00
it913x-fe: Crystal Frequency :12000000 Adc Frequency :20250000 ADC X2: 00
it913x-fe: Tuner LNA type :38
usb 2-1: DVB: registering adapter 2 frontend 0 (Digital Dual TV Receiver CTVDIGDUAL_V2_2)...
usb 2-1: dvb_usb_v2: 'Digital Dual TV Receiver CTVDIGDUAL_V2' successfully initialized and connected
RC part not tested
Signed-off-by: Alessandro Miceli <angelofsky1980@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
