Add secure-boot for the dGPU set of GM20X chips, using the PMU as the
high-secure falcon.
This work is based on Deepak Goyal's initial port of Secure Boot to
Nouveau.
v2. use proper memory target function
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Secure falcons' firmware is managed by secboot. Do not load it in GR for
them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Start securely-managed falcons using secboot functions since the process
for them is different from just writing CPUCTL.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
On GM200 and later GPUs, firmware for some essential falcons (notably
GR ones) must be authenticated by a NVIDIA-produced signature and
loaded by a high-secure falcon in order to be able to access privileged
registers, in a process known as Secure Boot.
Secure Boot requires building a binary blob containing the firmwares
and signatures of the falcons to be loaded. This blob is then given to
a high-secure falcon running a signed loader firmware that copies the
blob into a write-protected region, checks that the signatures are
valid, and finally loads the verified firmware into the managed falcons
and switches them to privileged mode.
This patch adds infrastructure code to support this process on chips
that require it.
v2:
- The IRQ mask of the PMU falcon was left - replace it with the proper
irq_mask variable.
- The falcon reset procedure expecting a falcon in an initialized state,
which was accidentally provided by the PMU subdev. Make sure that
secboot can manage the falcon on its own.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Load firmware and bundles in GM200's constructor. The previously called
GF100 function did not care about the bundles.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
There functions are going to be used by other chips that rely on
NVIDIA-provided firmware. Export them.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Make these functions easier to use by handling memory management from
within.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The firmwares required by GR may vary from chip to chip, especially with
the introduction of secure boot and NVIDIA-provided firmwares. Move the
firmware loading outside of gf100_gr_ctor so other chips may still call
it while managing their firmwares themselves.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Some members of gf100_gr were freed by the gk20a driver. That's not
where it should be done - free them in gf100 so other chips that use
NVIDIA-provided firmware free these structures properly.
This also removes the need for a GK20A-specific destructor.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add memcpy functions to copy a buffer to a gpuobj and vice-versa. This
will be used by the secure boot code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Most of the per-chipset differences will go away when we fully switch
to using the register lists provided by the firmware files, which will
leave all the remaining code "belonging" to GM200.
This is a preemptive rename from GM204 to GM200.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Upon encountering an unknown condition code, the script interpreter
is supposed to skip 'size' bytes and continue at the next devinit
token.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It is not advisable to perform devinit if it has already been done.
VBIOS will very likely have invoked devinit if the GPU is the primary
graphics device, but there is no accurate way to detect this fact yet.
This patch adds such a method for gf100 and later chips, by means of the
NV_PTOP_SCRATCH1_DEVINIT_COMPLETED bit. This bit is set to 1 by devinit,
and reset to 0 when the GPU is powered.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
We never use any nv50-specific member in this nv50_devinit_preinit().
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nvkm_device_tegra_new initializes the irq member of the Tegra device
to -1 in order to signal that it is uninitialized. However,
nvkm_device_tegra_fini tests it against 0 to check whether an IRQ has
been allocated or not. This leads to free_irq being called on -1 during
device initialization.
Fix this by using 0 as the uninitialized value everywhere.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nvkm_device_fini is never called if a failure occurs in
nvkm_device_init, even when unloading the module. This can lead to a
resources leak (one example is the Tegra interrupt which would never be
freed in that case). Fix this by calling nvkm_device_fini in
nvkm_device_init's failure path.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Use the nvkm_firmware_* functions when loading external firmware to
avoid duplicate code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Add two functions nvkm_firmware_get() and nvkm_firmware_put() to load a
firmware file and free its resources, respectively. Since firmware files
are becoming a necessity for new GPUs, and their location has been
standardized to nvidia/chip/, this will prevent duplicate and
error-prone name-generation code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Patch "ltc/gm107: use nvkm_mask to set cbc_ctrl1" sets the 3rd bit
of the CTRL1 register instead of writing it entirely in
gm107_ltc_cbc_clear(). As a counterpart, gm107_ltc_cbc_wait() must also
be modified to wait on that single bit only, otherwise a timeout may
occur if some other bit of that register is set. This happened at least
on GM206 when running glmark2-drm.
While we are at it, use the more compact nvkm_wait_msec() to wait for
the bit to clear.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The copy_from_user() function returns the number of bytes not copied but
we want to return a negative error code.
Fixes: 463873d570 ('drm/vc4: Add an API for creating GPU shaders in GEM BOs.')
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
The original Raspberry Pi had the GPIO active high, but the later
models are active low. The DT GPIO bindings allow specifying the
active flag, except that it doesn't get propagated to the gpiodesc, so
you have to handle it yourself.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Daniel Stone <daniels@collabora.com>
Fixes an error thrown every few seconds when we poll HPD when it's on
a I2C to GPIO expander.
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Daniel Stone <daniels@collabora.com>
The hardware provides us with separate threads for binning and
rendering, and the existing model waits for them both to complete
before submitting the next job.
Splitting the binning and rendering submissions reduces idle time and
gives us approx 20-30% speedup with some x11perf tests such as -line10
and -tilerect1. Improves openarena performance by 1.01897% +/-
0.247857% (n=16).
Thanks to anholt for suggesting this.
v2: Rebase on the spurious resets fix (change by anholt).
Signed-off-by: Varad Gautam <varadgautam@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
This pull request fixes the major VC4 HDMI modesetting bugs found when
the first wave of users showed up in Raspbian.
* tag 'drm-vc4-fixes-2016-03-03' of github.com:anholt/linux:
drm/vc4: Initialize scaler DISPBKGND on modeset.
drm/vc4: Fix setting of vertical timings in the CRTC.
drm/vc4: Fix the name of the VSYNCD_EVEN register.
drm/vc4: Add another reg to HDMI debug dumping.
drm/vc4: Bring HDMI up from power off if necessary.
drm/vc4: Fix a framebuffer reference leak on async flip interrupt.
562c5b4d89 didn't quite fix the issue of dealing with an error
pointer. We can't free/unref an error pointer so reset it to NULL.
Many thanks to Dan Carpenter for pointing this out again.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: dri-devel@lists.freedesktop.org
Fixes: 562c5b4d89 ("drm: fix blob pointer check")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457698646-22231-1-git-send-email-lionel.g.landwerlin@intel.com
SADs may span multiple CEA audio data blocks in the EDID.
CEA-861-E says:
"The order of the Data Blocks is not constrained. It is also possible
to have more than one of a specific type of data block if necessary to
include all of the descriptors needed to describe the sink’s capabilities."
Each audio data block can carry up to 10 SADs, whereas the ELD SAD limit
is 15 according to HDA 1.0a spec. So we should support at least two data
blocks. And apparently some devices take a more liberal interpretation
and stuff only one SAD per data block even when they would fit into one.
So let's try to extract all the SADs we can fit into the ELD even when
they span multiple data blocks.
While at it, toss in a comment to explain the 13 byte monitor name
string limit which confused me at first.
Cc: Arturo Pérez <artur999555@gmail.com>
Tested-by: Arturo Pérez <artur999555@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94197
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457554066-8739-1-git-send-email-ville.syrjala@linux.intel.com
The commit d931589c01 ("drm/exynos: remove DRM_EXYNOS_GEM_MAP_OFFSET
ioctl") removed it same with the ioctl that this patch adds. The reason
that removed DRM_EXYNOS_GEM_MAP_OFFSET was we could use
DRM_IOCTL_MODE_MAP_DUMB. Both did exactly same thing.
Now we again will revive it as DRM_EXYNOS_GEM_MAP because of render
node. DRM_IOCTL_MODE_MAP_DUMB isn't permitted in render node.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Two i915 regression fixes.
* tag 'drm-intel-fixes-2016-03-11' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Actually retry with bit-banging after GMBUS timeout
drm/i915: Fix bogus dig_port_map[] assignment for pre-HSW
Two more fixes for 4.5:
- One is a fix for OMAP that is urgently needed to avoid DRA7xx chips from
premature aging, by always keeping the Ethernet clock enabled.
- The other solves a I/O memory layout issue on Armada, where SROM and PCI
memory windows were conflicting in some configurations.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/uWT
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Two more fixes for 4.5:
- One is a fix for OMAP that is urgently needed to avoid DRA7xx chips
from premature aging, by always keeping the Ethernet clock enabled.
- The other solves a I/O memory layout issue on Armada, where SROM
and PCI memory windows were conflicting in some configurations"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mvebu: fix overlap of Crypto SRAM with PCIe memory window
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=btba
-----END PGP SIGNATURE-----
Merge tag 'media/v4.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"One last time fix: It adds a code that prevents some media tools like
media-ctl to hide some entities that have their IDs out of the range
expected by those apps"
* tag 'media/v4.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media-device: map new functions into old types for legacy API
When the Crypto SRAM mappings were added to the Device Tree files
describing the Armada XP boards in commit c466d997bb ("ARM: mvebu:
define crypto SRAM ranges for all armada-xp boards"), the fact that
those mappings were overlaping with the PCIe memory aperture was
overlooked. Due to this, we currently have for all Armada XP platforms
a situation that looks like this:
Memory mapping on Armada XP boards with internal registers at
0xf1000000:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf8000000 -> 0xffe0000 126M PCIe memory aperture
- 0xf8100000 -> 0xf8110000 64KB Crypto SRAM #0 => OVERLAPS WITH PCIE !
- 0xf8110000 -> 0xf8120000 64KB Crypto SRAM #1 => OVERLAPS WITH PCIE !
- 0xffe00000 -> 0xfff00000 1M PCIe I/O aperture
- 0xfff0000 -> 0xffffffff 1M BootROM
The overlap means that when PCIe devices are added, depending on their
memory window needs, they might or might not be mapped into the
physical address space. Indeed, they will not be mapped if the area
allocated in the PCIe memory aperture by the PCI core overlaps with
one of the Crypto SRAM. Typically, a Intel IGB PCIe NIC that needs 8MB
of PCIe memory will see its PCIe memory window allocated from
0xf80000000 for 8MB, which overlaps with the Crypto SRAM windows. Due
to this, the PCIe window is not created, and any attempt to access the
PCIe window makes the kernel explode:
[ 3.302213] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.307841] pci 0000:00:09.0: enabling device (0140 -> 0143)
[ 3.313539] mvebu_mbus: cannot add window '4:f8', conflicts with another window
[ 3.320870] mvebu-pcie soc:pcie-controller: Could not create MBus window at [mem 0xf8000000-0xf87fffff]: -22
[ 3.330811] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf08c0018
This problem does not occur on Armada 370 boards, because we use the
following memory mapping (for boards that have internal registers at
0xf1000000):
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0 => OK !
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Obviously, the solution is to align the location of the Crypto SRAM
mappings of Armada XP to be similar with the ones on Armada 370, i.e
have them between the "internal registers" area and the beginning of
the PCIe aperture.
However, we have a special case with the OpenBlocks AX3-4 platform,
which has a 128 MB NOR flash. Currently, this NOR flash is mapped from
0xf0000000 to 0xf8000000. This is possible because on OpenBlocks
AX3-4, the internal registers are not at 0xf1000000. And this explains
why the Crypto SRAM mappings were not configured at the same place on
Armada XP.
Hence, the solution is two-fold:
(1) Move the NOR flash mapping on Armada XP OpenBlocks AX3-4 from
0xe8000000 to 0xf0000000. This frees the 0xf0000000 ->
0xf80000000 space.
(2) Move the Crypto SRAM mappings on Armada XP to be similar to
Armada 370 (except of course that Armada XP has two Crypto SRAM
and not one).
After this patch, the memory mapping on Armada XP boards with
registers at 0xf1 is:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
And the memory mapping for the special case of the OpenBlocks AX3-4
(internal registers at 0xd0000000, NOR of 128 MB):
- 0x00000000 -> 0xc0000000 3G RAM
- 0xd0000000 -> 0xd1000000 1M internal registers
- 0xe800000 -> 0xf0000000 128M NOR flash
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Fixes: c466d997bb ("ARM: mvebu: define crypto SRAM ranges for all armada-xp boards")
Reported-by: Phil Sutter <phil@nwl.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Few more late fixes on drivers nothing major here.
- A memory leak fix in fsdma unmap the dma descriptors on
freeup.
- A fix in xdmac driver for residue calculation of dma
descriptor.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Y4sQ
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-fix-4.5' of git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Two fixes showed up in last few days, and they should be included in
4.5. Summary:
Two more late fixes to drivers, nothing major here:
- A memory leak fix in fsdma unmap the dma descriptors on freeup
- A fix in xdmac driver for residue calculation of dma descriptor"
* tag 'dmaengine-fix-4.5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: at_xdmac: fix residue computation
dmaengine: fsldma: fix memory leak
- Revert a recent ACPICA commit that has been reverted
upstream, because it caused problems to happen on user
systems and the problem it attempted to address will not be
relevant any more after upcoming ACPI specification changes
(Bob Moore).
- Fix crash in the generic device properties framework introduced
by a recent change that forgot to check pointers against error
values in addition to checking them against NULL (Heikki Krogerus).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Pi1c
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.5-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Two more fixes for issues introduced recently, one in the generic
device properties framework and one in ACPICA.
Specifics:
- Revert a recent ACPICA commit that has been reverted upstream,
because it caused problems to happen on user systems and the
problem it attempted to address will not be relevant any more after
upcoming ACPI specification changes (Bob Moore).
- Fix crash in the generic device properties framework introduced by
a recent change that forgot to check pointers against error values
in addition to checking them against NULL (Heikki Krogerus)"
* tag 'pm+acpi-4.5-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: fwnode->secondary may contain ERR_PTR(-ENODEV)
ACPICA: Revert "Parser: Fix for SuperName method invocation"
Changes:
o Only perform torn log write detection on dirty logs. This prevents
failures being detected due to a clean filesystem being moved
between machines or kernels of different architectures (e.g. 32
-> 64 bit, BE -> LE, etc). This fixes a regression introduced by
the torn log write detection in 4.5-rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NDeH
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-4.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This is a fix for a regression introduced in 4.5-rc1 by the new torn
log write detection code. The regression only affects people moving a
clean filesystem between machines/kernels of different architecture
(such as changing between 32 bit and 64 bit kernels), but this is the
recommended (and only!) safe way to migrate a filesystem between
architectures so we really need to ensure it works.
The changes are larger than I'd prefer right at the end of the release
cycle, but the majority of the change is just factoring code to enable
the detection of a clean log at the correct time to avoid this issue.
Changes:
- Only perform torn log write detection on dirty logs. This prevents
failures being detected due to a clean filesystem being moved
between machines or kernels of different architectures (e.g. 32 ->
64 bit, BE -> LE, etc). This fixes a regression introduced by the
torn log write detection in 4.5-rc1"
* tag 'xfs-for-linus-4.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: only run torn log write detection on dirty logs
xfs: refactor in-core log state update to helper
xfs: refactor unmount record detection into helper
xfs: separate log head record discovery from verification
Pull vfs fixes from Al Viro:
"A couple of fixes: Fix for my dumb braino in ncpfs and a long-standing
breakage on recovery from failed rename() in jffs2"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
jffs2: reduce the breakage on recovery from halfway failed rename()
ncpfs: fix a braino in OOM handling in ncp_fill_cache()
After the GMBUS transfer times out, we set force_bit=1 and
return -EAGAIN expecting the i2c core to call the .master_xfer
hook again so that we will retry the same transfer via bit-banging.
This is in case the gmbus hardware is somehow faulty.
Unfortunately we left adapter->retries to 0, meaning the i2c core
didn't actually do the retry. Let's tell the core we want one retry
when we return -EAGAIN.
Note that i2c-algo-bit also uses this retry count for some internal
retries, so we'll end up increasing those a bit as well.
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: bffce907d6 ("drm/i915: abstract i2c bit banging fallback in gmbus xfer")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1457366220-29409-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 8b1f165a4a)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
is a bit larger because the surrounding code needed a cleanup, but
nothing worrisome.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJW4UwZAAoJEL/70l94x66DG3YH/0PfUr4sW0jnWRVXmYlPVka4
sNFYrdtYnx08PwXu2sWMm1F+OBXlF/t0ZSJXJ9OBF8WdKIu8TU4yBOINRAvGO/oE
slrivjktLTKgicTtIXP5BpRR14ohwHIGcuiIlppxvnhmQz1/rMtig7fvhZxYI545
lJyIbyquNR86tiVdUSG9/T9+ulXXXCvOspYv8jPXZx7VKBXKTvp5P5qavSqciRb+
O9RqY+GDCR/5vrw+MV0J7H9ZydeEJeD02LcWguTGMATTm0RCrhydvSbou42UcKfY
osWii0kwt2LhcM/sTOz+cWnLJ6gwU9T+ZtJTTbLvYWXWDLP/+icp9ACMkwNciNo=
=/y4V
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"A few simple fixes for ARM, x86, PPC and generic code.
The x86 MMU fix is a bit larger because the surrounding code needed a
cleanup, but nothing worrisome"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: MMU: fix reserved bit check for ept=0/CR0.WP=0/CR4.SMEP=1/EFER.NX=0
KVM: MMU: fix ept=0/pte.u=1/pte.w=0/CR0.WP=0/CR4.SMEP=1/EFER.NX=0 combo
kvm: cap halt polling at exactly halt_poll_ns
KVM: s390: correct fprs on SIGP (STOP AND) STORE STATUS
KVM: VMX: disable PEBS before a guest entry
KVM: PPC: Book3S HV: Sanitize special-purpose register values on guest exit
- Temporarily disable huge pages built using contiguous ptes
- Ensure vmemmap region is sufficiently aligned for sparsemem sections
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJW4FSYAAoJELescNyEwWM0cp4H/0+9iMTqb3KowIW1vQPNnOG2
BG/RVsGlCPAwBu0V4FdcY7eK4fQ9J+/UCmVd5/SrlpjNpblinxRPihbIzs4bToqa
It02wNk7ISPm0oYtyGrRu1TpC5AvMykcluZkU/CUk0sjZlBAi8WSaJiqftFuZSGH
lhyhARO4KscbAUUhwDDYNKuWmLbmyOpt9RM2fziNQdjSp+8czCoCR9G+JXiPQFsJ
ORU10BqBDCyFpp8/NhM55qA76FJo6RCBUWx/6L1oJJxjvahkmPba/hhnfI7+Xj1u
3FKAntJ6wVZeKqRsIkOlECoU/mrgjlTByTFN+o3KhOky8ZYBHoveIQWtsqNMFd4=
=7d1o
-----END PGP SIGNATURE-----
Merge tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"I thought we were done for 4.5, but then the 64k-page chaps came
crawling out of the woodwork. *sigh*
The vmemmap fix I sent for -rc7 caused a regression with 64k pages and
sparsemem and at some point during the release cycle the new hugetlb
code using contiguous ptes started failing the libhugetlbfs tests with
64k pages enabled.
So here are a couple of patches that fix the vmemmap alignment and
disable the new hugetlb page sizes whilst a proper fix is being
developed:
- Temporarily disable huge pages built using contiguous ptes
- Ensure vmemmap region is sufficiently aligned for sparsemem
sections"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: hugetlb: partial revert of 66b3923a1a
arm64: account for sparsemem section alignment when choosing vmemmap offset
Pull s390 fixes from Martin Schwidefsky:
"Three bug fixes:
- The fix for the page table corruption (CVE-2016-2143)
- The diagnose statistics introduced a regression for the dasd diag
driver
- Boot crash on systems without the set-program-parameters facility"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: four page table levels vs. fork
s390/cpumf: Fix lpp detection
s390/dasd: fix diag 0x250 inline assembly
The legacy media controller userspace API exposes entity types that
carry both type and function information. The new API replaces the type
with a function. It preserves backward compatibility by defining legacy
functions for the existing types and using them in drivers.
This works fine, as long as newer entity functions won't be added.
Unfortunately, some tools, like media-ctl with --print-dot argument
rely on the now legacy MEDIA_ENT_T_V4L2_SUBDEV and MEDIA_ENT_T_DEVNODE
numeric ranges to identify what entities will be shown.
Also, if the entity doesn't match those ranges, it will ignore the
major/minor information on devnodes, and won't be getting the devnode
name via udev or sysfs.
As we're now adding devices outside the old range, the legacy ioctl
needs to map the new entity functions into a type at the old range,
or otherwise we'll have a regression.
Detected on all released media-ctl versions (e. g. versions <= 1.10).
Fix this by deriving the type from the function to emulate the legacy
API if the function isn't in the legacy functions range.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Check properly that the allocated blob's pointer is valid.
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Daniel Stone <daniels@collabora.com>
Fixes: 5488dc16fd ("drm: introduce pipe color correction properties")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1457611461-9116-1-git-send-email-lionel.g.landwerlin@intel.com
