commit cf9d052aa6005f1e8dfaf491d83bf37f368af69e upstream.
In Linux, if a driver does disable_irq() and later does enable_irq()
on its interrupt, I believe it's expecting these properties:
* If an interrupt was pending when the driver disabled then it will
still be pending after the driver re-enables.
* If an edge-triggered interrupt comes in while an interrupt is
disabled it should assert when the interrupt is re-enabled.
If you think that the above sounds a lot like the disable_irq() and
enable_irq() are supposed to be masking/unmasking the interrupt
instead of disabling/enabling it then you've made an astute
observation. Specifically when talking about interrupts, "mask"
usually means to stop posting interrupts but keep tracking them and
"disable" means to fully shut off interrupt detection. It's
unfortunate that this is so confusing, but presumably this is all the
way it is for historical reasons.
Perhaps more confusing than the above is that, even though clients of
IRQs themselves don't have a way to request mask/unmask
vs. disable/enable calls, IRQ chips themselves can implement both.
...and yet more confusing is that if an IRQ chip implements
disable/enable then they will be called when a client driver calls
disable_irq() / enable_irq().
It does feel like some of the above could be cleared up. However,
without any other core interrupt changes it should be clear that when
an IRQ chip gets a request to "disable" an IRQ that it has to treat it
like a mask of that IRQ.
In any case, after that long interlude you can see that the "unmask
and clear" can break things. Maulik tried to fix it so that we no
longer did "unmask and clear" in commit 71266d9d39 ("pinctrl: qcom:
Move clearing pending IRQ to .irq_request_resources callback"), but it
only handled the PDC case and it had problems (it caused
sc7180-trogdor devices to fail to suspend). Let's fix.
>From my understanding the source of the phantom interrupt in the
were these two things:
1. One that could have been introduced in msm_gpio_irq_set_type()
(only for the non-PDC case).
2. Edges could have been detected when a GPIO was muxed away.
Fixing case #1 is easy. We can just add a clear in
msm_gpio_irq_set_type().
Fixing case #2 is harder. Let's use a concrete example. In
sc7180-trogdor.dtsi we configure the uart3 to have two pinctrl states,
sleep and default, and mux between the two during runtime PM and
system suspend (see geni_se_resources_{on,off}() for more
details). The difference between the sleep and default state is that
the RX pin is muxed to a GPIO during sleep and muxed to the UART
otherwise.
As per Qualcomm, when we mux the pin over to the UART function the PDC
(or the non-PDC interrupt detection logic) is still watching it /
latching edges. These edges don't cause interrupts because the
current code masks the interrupt unless we're entering suspend.
However, as soon as we enter suspend we unmask the interrupt and it's
counted as a wakeup.
Let's deal with the problem like this:
* When we mux away, we'll mask our interrupt. This isn't necessary in
the above case since the client already masked us, but it's a good
idea in general.
* When we mux back will clear any interrupts and unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Fixes: 71266d9d39 ("pinctrl: qcom: Move clearing pending IRQ to .irq_request_resources callback")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210114191601.v7.4.I7cf3019783720feb57b958c95c2b684940264cd1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a95881d6aa2c000e3649f27a1a7329cf356e6bb3 upstream.
In commit 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for
msm gpio") we tried to Ack interrupts during unmask. However, that
patch forgot to check "intr_ack_high" so, presumably, it only worked
for a certain subset of SoCs.
Let's add a small accessor so we don't need to open-code the logic in
both places.
This was found by code inspection. I don't have any access to the
hardware in question nor software that needs the Ack during unmask.
Fixes: 4b7618fdc7 ("pinctrl: qcom: Add irq_enable callback for msm gpio")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.3.I32d0f4e174d45363b49ab611a13c3da8f1e87d0f@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4079d35fa4fca4ee0ffd66968312fc86a5e8c290 upstream.
When the Qualcomm pinctrl driver wants to Ack an interrupt, it does a
read-modify-write on the interrupt status register. On some SoCs it
makes sure that the status bit is 1 to "Ack" and on others it makes
sure that the bit is 0 to "Ack". Presumably the first type of
interrupt controller is a "write 1 to clear" type register and the
second just let you directly set the interrupt status register.
As far as I can tell from scanning structure definitions, the
interrupt status bit is always in a register by itself. Thus with
both types of interrupt controllers it is safe to "Ack" interrupts
without doing a read-modify-write. We can do a simple write.
It should be noted that if the interrupt status bit _was_ ever in a
register with other things (like maybe status bits for other GPIOs):
a) For "write 1 clear" type controllers then read-modify-write would
be totally wrong because we'd accidentally end up clearing
interrupts we weren't looking at.
b) For "direct set" type controllers then read-modify-write would also
be wrong because someone setting one of the other bits in the
register might accidentally clear (or set) our interrupt.
I say this simply to show that the current read-modify-write doesn't
provide any sort of "future proofing" of the code. In fact (for
"write 1 clear" controllers) the new code is slightly more "future
proof" since it would allow more than one interrupt status bits to
share a register.
NOTE: this code fixes no bugs--it simply avoids an extra register
read.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.2.I3635de080604e1feda770591c5563bd6e63dd39d@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a82e537807d5c85706cd4c16fd2de77a8495dc8d upstream.
There's currently a comment in the code saying function 0 is GPIO.
Instead of hardcoding it, let's add a member where an SoC can specify
it. No known SoCs use a number other than 0, but this just makes the
code clearer. NOTE: no SoC code needs to be updated since we can rely
on zero-initialization.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Maulik Shah <mkshah@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210114191601.v7.1.I3ad184e3423d8e479bc3e86f5b393abb1704a1d1@changeid
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 81bd1579b43e0e285cba667399f1b063f1ce7672 ]
Some SoCs, eg. mt8183, are using a pinconfig operation bias_set_combo.
The fallback path in mtk_pinconf_adv_pull_set() should also try this
operation.
Fixes: cafe19db77 ("pinctrl: mediatek: Backward compatible to previous Mediatek's bias-pull usage")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/20201228090425.2130569-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 92ff62a7bcc17d47c0ce8dddfb7a6e1a2e55ebf4 ]
The SCU offset for signal PWM8 in group PWM8G0 is wrong, fix it from
SCU414 to SCU4B4.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Fixes: 2eda1cdec4 ("pinctrl: aspeed: Add AST2600 pinmux support")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20201217024912.3198-1-billy_tsai@aspeedtech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 9a85c09a3f507b925d75cb0c7c8f364467038052 upstream.
- JZ4760 and JZ4760B have a similar register layout as the JZ4740, and
don't use the new register layout, which was introduced with the
JZ4770 SoC and not the JZ4760 or JZ4760B SoCs.
- The JZ4740 code path only expected two function modes to be
configurable for each pin, and wouldn't work with more than two. Fix
it for the JZ4760, which has four configurable function modes.
Fixes: 0257595a5c ("pinctrl: Ingenic: Add pinctrl driver for JZ4760 and JZ4760B.")
Cc: <stable@vger.kernel.org> # 5.3
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201211232810.261565-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a1158e36f876f6269978a4176e3a1d48d27fe7a1 upstream.
It is found on many allwinner soc that there is a low probability that
the interrupt status cannot be read in sunxi_pinctrl_irq_handler. This
will cause the interrupt status of a gpio bank to always be active on
gic, preventing gic from responding to other spi interrupts correctly.
So we should call the chained_irq_* each time enter sunxi_pinctrl_irq_handler().
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/85263ce8b058e80cea25c6ad6383eb256ce96cc8.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6de7ed693c631d4689acfe90c434147598d75543 ]
A100's pin starts with PB, so it should start with 1.
Fixes: 473436e764 ("pinctrl: sunxi: add support for the Allwinner A100 pin controller")
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Link: https://lore.kernel.org/r/9db51667bf9065be55beafd56e5c319e3bbe8310.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Mistakenly the buffers (input and output) become enabled together for a short
period of time during GPIO request. This is problematic, because instead of
initial motive to disable them in the commit af7e3eeb84
("pinctrl: intel: Disable input and output buffer when switching to GPIO"),
the driven value on the pin, which might be used as an IRQ line, brings
firmwares of some touch pads to an awkward state that needs a full power off
to recover. Fix this, as stated in the culprit commit, by disabling the buffers.
Fixes: af7e3eeb84 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210497
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201208182403.40435-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 6726fbff19bf ("pinctrl: aspeed: Fix GPI only function problem.")
fixes access to GPIO banks T and U on the AST2600. Both banks contain
input-only pins and the GPIO pin function is named GPITx and GPIUx
respectively. Unfortunately the fix had a negative impact on GPIO banks
D and E for the AST2400 and AST2500 where the GPIO pass-through
functions take similar "GPI"-style names. The net effect on the older
SoCs was that when the GPIO subsystem requested a pin in banks D or E be
muxed for GPIO, they were instead muxed for pass-through mode.
Mistakenly muxing pass-through mode e.g. breaks booting the host on
IBM's Witherspoon (AC922) platform where GPIOE0 is used for FSI.
Further exploit the names in the provided expression structure to
differentiate pass-through from pin-specific GPIO modes.
This follow-up fix gives the expected behaviour for the following tests:
Witherspoon BMC (AST2500):
1. Power-on the Witherspoon host
2. Request GPIOD1 be muxed via /sys/class/gpio/export
3. Request GPIOE1 be muxed via /sys/class/gpio/export
4. Request the balls for GPIOs E2 and E3 be muxed as GPIO pass-through
("GPIE2" mode) via a pinctrl hog in the devicetree
Rainier BMC (AST2600):
5. Request GPIT0 be muxed via /sys/class/gpio/export
6. Request GPIU0 be muxed via /sys/class/gpio/export
Together the tests demonstrate that all three pieces of functionality
(general GPIOs via 1, 2 and 3, input-only GPIOs via 5 and 6, pass-through
mode via 4) operate as desired across old and new SoCs.
Fixes: 9b92f5c51e ("pinctrl: aspeed: Fix GPI only function problem.")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Billy Tsai <billy_tsai@aspeedtech.com>
Cc: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201126063337.489927-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Fix HOSTSW_OWN offset and unhide SPI group of pins on Jasper Lake
* Fix debounce configuration on Baytrail when it's turned off
* Fix default bias setting on Merrifield
The following is an automated git shortlog grouped by driver:
baytrail:
- Avoid clearing debounce value when turning it off
jasperlake:
- Fix HOSTSW_OWN offset
- Unhide SPI group of pins
merrifield:
- Set default bias in case no particular value given
-----BEGIN PGP SIGNATURE-----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=xymw
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.10-3' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.10-3
* Fix HOSTSW_OWN offset and unhide SPI group of pins on Jasper Lake
* Fix debounce configuration on Baytrail when it's turned off
* Fix default bias setting on Merrifield
The following is an automated git shortlog grouped by driver:
baytrail:
- Avoid clearing debounce value when turning it off
jasperlake:
- Fix HOSTSW_OWN offset
- Unhide SPI group of pins
merrifield:
- Set default bias in case no particular value given
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
GPIOs that attempt to use interrupts get thwarted with a message like:
"pin 161 cannot be used as IRQ" (for instance with SD_CD). This is because
the HOSTSW_OWN offset is incorrect, so every GPIO looks like it's
owned by ACPI.
Fixes: e278dcb704 ("pinctrl: intel: Add Intel Jasper Lake pin controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If the group of pins is hidden in the pin list it affects
the register offset calculation despite fixed GPIO base.
Hence, the offsets of all pins after the hidden group
are broken. Instead we have to unhide the group and use a flag
to exclude it from GPIO number space.
Fixes: e278dcb704 ("pinctrl: intel: Add Intel Jasper Lake pin controller support")
Reported-by: Divagar Mohandass <divagar.mohandass@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
* Respect bias setting when comes from ACPI
The following is an automated git shortlog grouped by driver:
intel:
- Set default bias in case no particular value given
- Fix 2 kOhm bias which is 833 Ohm
-----BEGIN PGP SIGNATURE-----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=Voi9
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.10-2
* Respect bias setting when comes from ACPI
The following is an automated git shortlog grouped by driver:
intel:
- Set default bias in case no particular value given
- Fix 2 kOhm bias which is 833 Ohm
Specify the PDC mapping for SM8250, so that gpio interrupts are
propertly mapped to the wakeup IRQs of the PDC.
Fixes: 4e3ec9e407 ("pinctrl: qcom: Add sm8250 pinctrl driver.")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201028043642.1141723-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When GPIOs that are routed to PDC are used as output they can still latch
the IRQ pending at GIC. As a result the spurious IRQ was handled when the
client driver change the direction to input to starts using it as IRQ.
Currently such erroneous latched IRQ are cleared with .irq_enable callback
however if the driver continue to use GPIO as interrupt and invokes
disable_irq() followed by enable_irq() then everytime during enable_irq()
previously latched interrupt gets cleared.
This can make edge IRQs not seen after enable_irq() if they had arrived
after the driver has invoked disable_irq() and were pending at GIC.
Move clearing erroneous IRQ to .irq_request_resources callback as this is
the place where GPIO direction is changed as input and its locked as IRQ.
While at this add a missing check to invoke msm_gpio_irq_clear_unmask()
from .irq_enable callback only when GPIO is not routed to PDC.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1604561884-10166-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RTC is 32.768kHz thus 512 RtcClk equals 15625 usec. The documentation
likely has dropped precision and that's why the driver mistakenly took
the slightly deviated value.
Cc: stable@vger.kernel.org
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Coiby Xu <coiby.xu@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/linux-gpio/2f4706a1-502f-75f0-9596-cc25b4933b6c@redhat.com/
Link: https://lore.kernel.org/r/20201105231912.69527-3-coiby.xu@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some gpio pin at aspeed soc is input only and the prefix name of these
pin is "GPI" only.
This patch fine-tune the condition of GPIO check from "GPIO" to "GPI"
and it will fix the usage error of banks D and E in the AST2400/AST2500
and banks T and U in the AST2600.
Fixes: 4d3d0e4272 ("pinctrl: Add core support for Aspeed SoCs")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20201030055450.29613-1-billy_tsai@aspeedtech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is useful for debugging to have the error message printed
when regmap initialisation fails. Add it to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20201009180856.4738-2-andriy.shevchenko@linux.intel.com
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that simplification of mcp23s08_spi_regmap_init() made
a regression due to wrong size calculation for dev_kmemdup() call.
It misses the fact that config variable is already a pointer, thus
the sizeof() calculation is wrong and only 4 or 8 bytes were copied.
Fix the parameters to devm_kmemdup() to copy a full chunk of memory.
Fixes: 0874758ecb ("pinctrl: mcp23s08: Refactor mcp23s08_spi_regmap_init()")
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20201009180856.4738-1-andriy.shevchenko@linux.intel.com
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove totally irq mappings create in probe, the gpio irq mapping will
be created when do
gpio_to_irq ->
rockchip_gpio_to_irq ->
irq_create_mapping
This patch can speed up system boot on, also abandon many unused irq
mappings' create.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20201013063731.3618-4-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There need to enable pclk_gpio when do irq_create_mapping, since it will
do access to gpio controller.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20201013063731.3618-3-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The values for the SSI pins on GPIO chips D and E were off by 0x20.
Fixes: d3ef8c6b22 ("pinctrl: Ingenic: Add SSI pins support for JZ4770 and JZ4780.")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Artur Rojek <contact@artur-rojek.eu>
Link: https://lore.kernel.org/r/20201010192509.9098-1-paul@crapouillou.net
Reviewed-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel pin control hardware the 5 kOhm sounds plausible
because on one hand it's a minimum of resistors present in all
hardware generations and at the same time it's high enough to minimize
leakage current (will be only 200 uA with the above choice).
Fixes: e57725eabf ("pinctrl: intel: Add support for hardware debouncer")
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2 kOhm bias was never an option in Intel GPIO hardware, the available
matrix is:
000 none
001 1 kOhm (if available)
010 5 kOhm
100 20 kOhm
As easy to get the 3 resistors are gated separately and according to
parallel circuits calculations we may get combinations of the above where
the result is always strictly less than minimal resistance. Hence,
additional values can be:
011 ~833.3 Ohm
101 ~952.4 Ohm
110 ~4 kOhm
111 ~800 Ohm
That said, convert TERM definitions to be the bit masks to reflect the above.
While at it, enable the same setting for pull down case.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Cc: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Core changes:
- NONE whatsoever, we don't even touch the core files this
time around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and
groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile
drivers.
- The "SH-PFC" (literally SuperH pin function controller, I
think) subdirectory is now renamed to the more neutral
"renesas", as these are not very much centered around
SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver.
-----BEGIN PGP SIGNATURE-----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=TdjX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- NONE whatsoever, we don't even touch the core files this time
around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile drivers.
- The "SH-PFC" (literally SuperH pin function controller, I think)
subdirectory is now renamed to the more neutral "renesas", as these
are not very much centered around SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver"
* tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (78 commits)
pinctrl: amd: Add missing pins to the pin group list
dt-bindings: pinctrl: sunxi: Allow pinctrl with more interrupt banks
pinctrl: visconti: PINCTRL_TMPV7700 should depend on ARCH_VISCONTI
pinctrl: mediatek: Free eint data on failure
pinctrl: single: fix debug output when #pinctrl-cells = 2
pinctrl: single: fix pinctrl_spec.args_count bounds check
pinctrl: sunrisepoint: Modify COMMUNITY macros to be consistent
pinctrl: cannonlake: Modify COMMUNITY macros to be consistent
pinctrl: tigerlake: Fix register offsets for TGL-H variant
pinctrl: Document pinctrl-single,pins when #pinctrl-cells = 2
pinctrl: mediatek: use devm_platform_ioremap_resource_byname()
pinctrl: nuvoton: npcm7xx: Constify static ops structs
pinctrl: mediatek: mt7622: add antsel pins/groups
pinctrl: ocelot: simplify the return expression of ocelot_gpiochip_register()
pinctrl: at91-pio4: add support for sama7g5 SoC
dt-bindings: pinctrl: at91-pio4: add microchip,sama7g5
pinctrl: spear: simplify the return expression of tvc_connect()
pinctrl: spear: simplify the return expression of spear310_pinctrl_probe
pinctrl: sprd: use module_platform_driver to simplify the code
pinctrl: Ingenic: Add I2S pins support for Ingenic SoCs.
...
Core changes:
- The big core change is the updated (v2) userspace character
device API. This corrects badly designed 64-bit alignment around
the line events. We also add the debounce request feature.
This echoes the often quotes passage from Frederick Brooks
"The mythical man-month" to always throw one away, which we
have seen before in things such as V4L2. So we put in a new
one and deprecate and obsolete the old one.
- All example tools in tools/gpio/* are migrated to the new API
to set a good example. The libgpiod userspace library has been
augmented to use this new API pretty much from day 1.
- Some misc API hardening by using strn* function calls has been
added as well.
- Use the simpler IDA interface for GPIO chip instance enumeration.
- Add device core function for counting string arrays in
device properties.
- Provide a generic library function kfree_strarray() that can
be used throughout the kernel.
Driver enhancements:
- The DesignWare dwapb-gpio driver has been enhanced and now
uses the IRQ handling in the gpiolib core.
- The mockup and aggregator drivers have seen some substantial
code clean-up and now use more of the core kernel
inftrastructure.
- Misc cleanups using dev_err_probe().
- The MXC drivers (Freescale/NXP) can now be built modularized,
which makes modularized GKI Android kernels happy.
-----BEGIN PGP SIGNATURE-----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=8CE2
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This time very little driver changes but lots of core changes.
We have some interesting cooperative work for ARM and Intel alike,
making the GPIO subsystem more and more suitable for industrial
systems and the like, in addition to the in-kernel users.
We touch driver core (device properties) and lib/* by adding one
simple string array free function, these are authored by Andy
Shevchenko who is a well known and recognized core helpers maintainers
so this should be fine.
We also see some Android GKI-related modularization in the MXC
drivers.
Core changes:
- The big core change is the updated (v2) userspace character device
API.
This corrects badly designed 64-bit alignment around the line
events. We also add the debounce request feature. This echoes the
often quotes passage from Frederick Brooks "The mythical man-month"
to always throw one away, which we have seen before in things such
as V4L2. So we put in a new one and deprecate and obsolete the old
one.
- All example tools in tools/gpio/* are migrated to the new API to
set a good example. The libgpiod userspace library has been
augmented to use this new API pretty much from day 1.
- Some misc API hardening by using strn* function calls has been
added as well.
- Use the simpler IDA interface for GPIO chip instance enumeration.
- Add device core function for counting string arrays in device
properties.
- Provide a generic library function kfree_strarray() that can be
used throughout the kernel.
Driver enhancements:
- The DesignWare dwapb-gpio driver has been enhanced and now uses the
IRQ handling in the gpiolib core.
- The mockup and aggregator drivers have seen some substantial code
clean-up and now use more of the core kernel inftrastructure.
- Misc cleanups using dev_err_probe().
- The MXC drivers (Freescale/NXP) can now be built modularized, which
makes modularized GKI Android kernels happy"
* tag 'gpio-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpiolib: Update header block in gpiolib-cdev.h
gpiolib: cdev: switch from kstrdup() to kstrndup()
docs: gpio: add a new document to its index.rst
gpio: pca953x: Add support for the NXP PCAL9554B/C
tools: gpio: add debounce support to gpio-event-mon
tools: gpio: add multi-line monitoring to gpio-event-mon
tools: gpio: port gpio-event-mon to v2 uAPI
tools: gpio: port gpio-hammer to v2 uAPI
tools: gpio: rename nlines to num_lines
tools: gpio: port gpio-watch to v2 uAPI
tools: gpio: port lsgpio to v2 uAPI
gpio: uapi: document uAPI v1 as deprecated
gpiolib: cdev: support setting debounce
gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL
gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL
gpiolib: cdev: support edge detection for uAPI v2
gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL
gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL
gpiolib: add build option for CDEV v1 ABI
gpiolib: make cdev a build option
...
Core:
- Allow trimming of interrupt hierarchy to support odd hardware setups
where only a subset of the interrupts requires the full hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI PRUSS,
Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the place.
-----BEGIN PGP SIGNATURE-----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=1ewL
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Allow trimming of interrupt hierarchy to support odd hardware
setups where only a subset of the interrupts requires the full
hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI
PRUSS, Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the
place"
* tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
dt-bindings: interrupt-controller: Add MStar interrupt controller
irqchip/irq-mst: Add MStar interrupt controller support
soc/tegra: pmc: Don't create fake interrupt hierarchy levels
soc/tegra: pmc: Allow optional irq parent callbacks
gpio: tegra186: Allow optional irq parent callbacks
genirq/irqdomain: Allow partial trimming of irq_data hierarchy
irqchip/qcom-pdc: Reset PDC interrupts during init
irqchip/qcom-pdc: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
genirq/PM: Introduce IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Use return value from irq_set_wake() call
pinctrl: qcom: Set IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags
ARM: Handle no IPI being registered in show_ipi_list()
MAINTAINERS: Add entries for Actions Semi Owl SIRQ controller
irqchip: Add Actions Semi Owl SIRQ controller
dt-bindings: interrupt-controller: Add Actions SIRQ controller binding
dt-bindings: dw-apb-ictl: Update binding to describe use as primary interrupt controller
irqchip/dw-apb-ictl: Add primary interrupt controller support
irqchip/dw-apb-ictl: Refactor priot to introducing hierarchical irq domains
genirq: Add stub for set_handle_irq() when !GENERIC_IRQ_MULTI_HANDLER
...
Some of the pins were not exposed in the initial driver or kept as
reserved. Exposing all of them now.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20201007111220.744348-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Toshiba Visconti TMPV7700 series pin controller is only present on
Visconti SoCs. Hence add a dependency on ARCH_VISCONTI, to prevent
asking the user about this driver when configuring a kernel without
Visconti platform support.
Fixes: a68a784426 ("pinctrl: visconti: Add Toshiba Visconti SoCs pinctrl support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20201005125049.26926-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag to enable/unmask the
wakeirqs during suspend entry.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-5-git-send-email-mkshah@codeaurora.org
msmgpio irqchip was not using return value of irq_set_irq_wake() callback
since previously GIC-v3 irqchip neither had IRQCHIP_SKIP_SET_WAKE flag nor
it implemented .irq_set_wake callback. This lead to irq_set_irq_wake()
return error -ENXIO.
However from 'commit 4110b5cbb0 ("irqchip/gic-v3: Allow interrupt to be
configured as wake-up sources")' GIC irqchip has IRQCHIP_SKIP_SET_WAKE
flag.
Use return value from irq_set_irq_wake() and irq_chip_set_wake_parent()
instead of always returning success.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-3-git-send-email-mkshah@codeaurora.org
Both IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags are already
set for msmgpio's parent PDC irqchip but GPIO interrupts do not get masked
during suspend or during setting irq type since genirq checks irqchip flag
of msmgpio irqchip which forwards these calls to its parent PDC irqchip.
Add irqchip specific flags for msmgpio irqchip to mask non wakeirqs during
suspend and mask before setting irq type. Masking before changing type make
sures any spurious interrupt is not detected during this operation.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-2-git-send-email-mkshah@codeaurora.org
The property #pinctrl-cells can either be 1 or 2:
- if #pinctrl-cells = <1>, then pinctrl_spec.args_count = 2
- if #pinctrl-cells = <2>, then pinctrl_spec.args_count = 3
All other values of pinctrl_spec.args_count are incorrect. This fix
checks the upper bound instead of just the lower bound.
Fixes: a133954188 ("pinctrl: single: parse #pinctrl-cells = 2")
Reported-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/linux-omap/3139716.CMS8C0sQ7x@zen.local/
Link: https://lore.kernel.org/r/20200930174839.1308344-1-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
check mtk_is_virt_gpio input parameter,
virtual gpio need to support eint mode.
add error handler for the ko case
to fix this boot fail:
pc : mtk_is_virt_gpio+0x20/0x38 [pinctrl_mtk_common_v2]
lr : mtk_gpio_get_direction+0x44/0xb0 [pinctrl_paris]
Fixes: edd5464650 ("pinctrl: mediatek: avoid virtual gpio trying to set reg")
Signed-off-by: Hanks Chen <hanks.chen@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Singed-off-by: Jie Yang <sin_jieyang@mediatek.com>
Link: https://lore.kernel.org/r/1597922546-29633-1-git-send-email-hanks.chen@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify COMMUNITY macros to be consistent with Tiger Lake and others.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20200929110306.40852-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify COMMUNITY macros to be consistent with Tiger Lake and others.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20200929110306.40852-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that almost traditionally the H variants have some deviations
in the register offsets in comparison to LP ones. This is the case for
Intel Tiger Lake as well. Fix register offsets for TGL-H variant.
Fixes: 653d96455e ("pinctrl: tigerlake: Add support for Tiger Lake-H")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20200929110306.40852-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Wang Xiaojun <wangxiaojun11@huawei.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/20200917064151.2184010-1-wangxiaojun11@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of these structs is to assign their address to various
ops fields in the pinctrl_desc struct, which are const pointers. Make
them const to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200926202342.31014-1-rikard.falkeborn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
