These messages don't seem to be errors but notifications
that some attribute isn't quite right.
Don't mark them as errors.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ccode is not NUL terminated. Presumably insisting on a terminator makes
brcms_c_country_valid() return false when it's not intended. ccode[2]
is sprom->leddc_on_time.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses a long standing issue of the driver with the
mac80211 .flush() callback. Since implementing the .flush() callback
a number of issues have been fixed, but a WARN_ON_ONCE() was still
triggered because the timeout on the flush could still occur.
This patch changes the awkward design using msleep() into one using
a waitqueue. The waiting flush() context will kick the transmit dma
when it is idle and the timeout used waiting for the event is set
to 500 ms. Worst case there can be 64 frames outstanding for transmit
in the driver. At a rate of 1Mbps that would take 1.5 seconds assuming
MTU is 1500 bytes and ignoring retries. The WARN_ON_ONCE() is also
removed as this was put in to indicate the flush timeout as a reason
for the driver to stall. That was not happening since fixing endless
AMPDU retries with following upstream commit:
commit 85091fc0a7
Author: Arend van Spriel <arend@broadcom.com>
Date: Thu Feb 23 18:38:22 2012 +0100
brcm80211: smac: fix endless retry of A-MPDU transmissions
bugzilla: 42840 <https://bugzilla.kernel.org/show_bug.cgi?id=42840>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=799168>
bugzilla@redhat: <https://bugzilla.redhat.com/show_bug.cgi?id=787649>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Camaleón <noelamac@gmail.com>
Cc: Milan Bouchet-Valat <nalimilan@club-internet.fr>
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported on the wireless list (see [1]) in which
brcmsmac ran into a fatal error:
[ 588.284074] brcmsmac bcma0:0: frameid != txh->TxFrameID
[ 588.284098] brcmsmac bcma0:0: MI_TFS: fatal
[ 588.284103] brcmsmac bcma0:0: wl0: fatal error, reinitializing
[ 588.286208] ieee80211 phy0: Hardware restart was requested
The tx status feedback is processed in a loop limiting the number of
frames processed in one run. The code terminate processing when the
limit is reached regardless the txstatus value read from the device
register. When that status is is flagged as being valid it must be
processed as the hardware will clear it after is has been read.
Bisecting was done by Seth Forshee and showed following commit as the
culprit:
commit 57fe504817
Author: Piotr Haber <phaber@broadcom.com>
Date: Wed Nov 28 21:44:07 2012 +0100
brcmsmac: fix bounds checking in tx/rx
[1] http://www.spinics.net/lists/linux-wireless/msg101293.html
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Cc: stable@vger.kernel.org
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dead code after AMPDU restructure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interface address of the wireless device is determined by
the permanent address stored in the device. This patch allows
it to be overridden from user-space.
Reported-by: Maximilian Engelhardt <maxi@daemonizer.de>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callbacks that access driver functions should do that under
perimeter lock protection. The add_interface() callback was lacking
this lock.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/brcm80211/brcmsmac/main.c: In function ‘brcms_b_recv’:
drivers/net/wireless/brcm80211/brcmsmac/main.c:7636: warning: ‘morepending’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of returning an error and filling a pointer
return the pointer and an ERR_PTR value in error cases.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel bandwidth handling isn't really quite right,
it assumes that a 40 MHz channel is really two 20 MHz
channels, which isn't strictly true. This is the way the
regulatory database handling is defined right now though
so remove the logic to handle other channel widths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Patches from Canonical involved the introduction of new source
files debug.[ch]. That coincided with other patches from Broadcom
introducing the same files.
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wlc_lcnphy_rx_iq_cal_gain is called during initialization, i. e. when
executing brcms_up.
But brcms_up is called from brcms_ops_start while the latter holds a spin lock.
Thus, we cannot use usleep_range but have to use udelay.
This fixes:
BUG: scheduling while atomic: NetworkManager/1652/0x00000200
[...]
Call Trace:
[<ffffffff81582522>] __schedule_bug+0x48/0x54
[<ffffffff815892b6>] __schedule+0x596/0x6d0
[<ffffffff81589719>] schedule+0x29/0x70
[<ffffffff8158893c>] schedule_hrtimeout_range_clock+0xfc/0x140
[<ffffffff81060f10>] ? update_rmtp+0x70/0x70
[<ffffffff81588993>] schedule_hrtimeout_range+0x13/0x20
[<ffffffff810495e0>] usleep_range+0x40/0x50
[<ffffffffa05dedcb>] wlc_lcnphy_rx_iq_cal.constprop.10+0x59b/0xa90 [brcmsmac]
[<ffffffffa05df4ce>] wlc_lcnphy_periodic_cal+0x20e/0x220 [brcmsmac]
[<ffffffffa05dce8d>] ? wlc_lcnphy_set_tx_pwr_ctrl+0x21d/0x3c0 [brcmsmac]
[<ffffffffa05e0cfc>] wlc_phy_init_lcnphy+0xacc/0x1100 [brcmsmac]
[<ffffffffa05e0230>] ? wlc_phy_txpower_recalc_target_lcnphy+0x90/0x90 [brcmsmac]
[<ffffffffa05d7c7d>] wlc_phy_init+0xcd/0x170 [brcmsmac]
[<ffffffffa05c9dfe>] brcms_b_bsinit.isra.65+0x12e/0x310 [brcmsmac]
[<ffffffffa05d061b>] brcms_c_init+0x8fb/0x1170 [brcmsmac]
[<ffffffffa05c3a0a>] brcms_init+0x5a/0x70 [brcmsmac]
[<ffffffffa05ce76c>] brcms_c_up+0x1ac/0x4a0 [brcmsmac]
[<ffffffffa05c3c65>] brcms_up+0x25/0x30 [brcmsmac]
[<ffffffffa05c44c0>] brcms_ops_start+0xd0/0x100 [brcmsmac]
[...]
Signed-off-by: Niels Ole Salscheider <niels_ole@salscheider-online.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This device can be found on some embedded devices connected to a
Broadcom SoC like the BCM4718.
I tested this with my Netgear WNDR3400 v1.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As described in the documentation of bcma_wflush16 in drivers/net
/wireless/brcm80211/brcmsmac/types.h some PCIe controllers of Broadcom
SoCs are broken. The PCIe controller on these SoCs are mostly used to
connect some additional wifi device to the SoC and some of these wifi
devices are supported by brcmsmac.
For my BCM43224 connected to the broken PCIe controller of the BCM4718 I
need an extra read after write in brcms_b_write_objmem() to prevent a
Data bus error. This fixes the problem reading tsf_random later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for bcma wifi core revision 17 which is found on
BCM4716/4717/4718 SoCs. The firmware version 610.812 for brcmsmac found
in linux-firmware does not support these cores, but a firmware
generated with b43-fwcutter from the proprietary broadcom wireless
driver works with these chips. This wifi core contains a revision 5
N-PHY and a revision 7 radio of type 0x2056.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using gcc v4.7.2 gave following warning:
CC [M] drivers/net/wireless/brcm80211/brcmsmac/aiutils.o
brcmsmac/aiutils.c: In function 'ai_deviceremoved':
brcmsmac/aiutils.c:733:9: error: 'w' may be used uninitialized
in this function [-Werror=uninitialized]
Inspection of the pci_read_config_dword() function showed it can
return without modifying the output variable 'w' so this patch
initializes it to 0.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: brcm80211-dev-list@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's a debug message to warn if this function is passed a NULL
pointer, but in order to print the message we have to dereference the
pointer. Obviously this isn't a good idea, so remove the message.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for 4313 iPA variant.
It is a variant of already supported 4313 ePA
and needs some PHY changes to work properly.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move functions in
preparation for 4313iPA changes
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put basic information about hardware in debugfs.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcms_b_txstatus and brcms_b_recv are off by one when
doing bounds checking on number of packets to process
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
brcms_c_isr returns true if interrupt was for us
and if dpc should be scheduled which is the same thing.
Simplify it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The .tx() callback function can drop packets when there is no
space in the DMA fifo. Propagate that information to caller
and make sure the freed sk_buff reference is not accessed.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding __printf helps spot format and argument mismatches.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
One of the debug macro invocations ended up with a stray 0 argument
where the format string should be. Remove it.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes sparse warning:
drivers/net/wireless/brcm80211/brcmsmac/main.c:308:10: sparse: symbol 'wlc_prio2prec_map' was not declared. Should it be static?
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These messages clutter up the trace buffer without adding any useful
information.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the brcmsmac_tx trace system for tx debugging. Existing code to dump
tx status and descriptors are converted to using tracepoints, allowing
for more efficient collection and post-processing of this data. These
tracepoints are placed to collect data for all tx frames instead of only
on errors. Logging of tx errors is also improved.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant message to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also convert relevant messages over to use thses macros.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This macro is used for messages related to the 802.11 MAC layer.
Relevant messages are also converted to use this macro.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert most uses of wiphy_* and pr_* for general error and debug
messages to use the internal debug macros instead. Most code used only
for initialization still use wiphy_err(), as well as some locations
which are executed too early to use the debug macros. Some debug
messages which are redundant or not useful are removed.
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
