Pull x86 FPU updates from Ingo Molnar:
"The main changes in this cycle were:
- do a large round of simplifications after all CPUs do 'eager' FPU
context switching in v4.9: remove CR0 twiddling, remove leftover
eager/lazy bts, etc (Andy Lutomirski)
- more FPU code simplifications: remove struct fpu::counter, clarify
nomenclature, remove unnecessary arguments/functions and better
structure the code (Rik van Riel)"
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/fpu: Remove clts()
x86/fpu: Remove stts()
x86/fpu: Handle #NM without FPU emulation as an error
x86/fpu, lguest: Remove CR0.TS support
x86/fpu, kvm: Remove host CR0.TS manipulation
x86/fpu: Remove irq_ts_save() and irq_ts_restore()
x86/fpu: Stop saving and restoring CR0.TS in fpu__init_check_bugs()
x86/fpu: Get rid of two redundant clts() calls
x86/fpu: Finish excising 'eagerfpu'
x86/fpu: Split old_fpu & new_fpu handling into separate functions
x86/fpu: Remove 'cpu' argument from __cpu_invalidate_fpregs_state()
x86/fpu: Split old & new FPU code paths
x86/fpu: Remove __fpregs_(de)activate()
x86/fpu: Rename lazy restore functions to "register state valid"
x86/fpu, kvm: Remove KVM vcpu->fpu_counter
x86/fpu: Remove struct fpu::counter
x86/fpu: Remove use_eager_fpu()
x86/fpu: Remove the XFEATURE_MASK_EAGER/LAZY distinction
x86/fpu: Hard-disable lazy FPU mode
x86/crypto, x86/fpu: Remove X86_FEATURE_EAGER_FPU #ifdef from the crc32c code
PPC KVM update for 4.10:
* Support for KVM guests on POWER9 using the hashed page table MMU.
* Updates and improvements to the halt-polling support on PPC, from
Suraj Jitindar Singh.
* An optimization to speed up emulated MMIO, from Yongji Xie.
* Various other minor cleanups.
The kvm module has the parameters halt_poll_ns, halt_poll_ns_grow, and
halt_poll_ns_shrink. Halt polling was recently added to the powerpc kvm-hv
module and these parameters were essentially duplicated for that. There is
no benefit to this duplication and it can lead to confusion when trying to
tune halt polling.
Thus move the definition of these variables to kvm_host.h and export them.
This will allow the kvm-hv module to use the same module parameters by
accessing these variables, which will be implemented in the next patch,
meaning that they will no longer be duplicated.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Change unimplemented msrs messages to use pr_debug.
If CONFIG_DYNAMIC_DEBUG is set, then these messages can be
enabled at run time or else -DDEBUG can be used at compile
time to enable them. These messages will still be printed if
ignore_msrs=1.
Signed-off-by: Bandan Das <bsd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
With the removal of the lazy FPU code, this field is no longer used.
Get rid of it.
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: pbonzini@redhat.com
Link: http://lkml.kernel.org/r/1475627678-20788-7-git-send-email-riel@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This commit adds the ability for archs to export
per-vcpu information via a new per-vcpu dir in
the VM's debugfs directory.
If kvm_arch_has_vcpu_debugfs() returns true, then KVM
will create a vcpu dir for each vCPU in the VM's
debugfs directory. Then kvm_arch_create_vcpu_debugfs()
is responsible for populating each vcpu directory
with arch specific entries.
The per-vcpu path in debugfs will look like:
/sys/kernel/debug/kvm/29162-10/vcpu0
/sys/kernel/debug/kvm/29162-10/vcpu1
This is all arch specific for now because the only
user of this interface (x86) wants to export x86-specific
per-vcpu information to user-space.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Two stubs are added:
o kvm_arch_has_vcpu_debugfs(): must return true if the arch
supports creating debugfs entries in the vcpu debugfs dir
(which will be implemented by the next commit)
o kvm_arch_create_vcpu_debugfs(): code that creates debugfs
entries in the vcpu debugfs dir
For x86, this commit introduces a new file to avoid growing
arch/x86/kvm/x86.c even more.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM devices were manipulating list data structures without any form of
synchronization, and some implementations of the create operations also
suffered from a lack of synchronization.
Now when we've split the xics create operation into create and init, we
can hold the kvm->lock mutex while calling the create operation and when
manipulating the devices list.
The error path in the generic code gets slightly ugly because we have to
take the mutex again and delete the device from the list, but holding
the mutex during anon_inode_getfd or releasing/locking the mutex in the
common non-error path seemed wrong.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
As we are about to hold the kvm->lock during the create operation on KVM
devices, we should move the call to xics_debugfs_init into its own
function, since holding a mutex over extended amounts of time might not
be a good idea.
Introduce an init operation on the kvm_device_ops struct which cannot
fail and call this, if configured, after the device has been created.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXoydqAAoJEEtpOizt6ddyM3oH/1A4VeG/J9q4fBPXqY2tVWXs
c3P7UgNcrEgUNs/F9ykQY/lb31deecUzaBt1OyTf+RlsNbihq3dQdYcBhxtUODw/
Faok582ya3UFgLW+IRHcID0EbkVOpIzMhOStYsnU/Dz7HG1JL9HdPzwkid7iu9LT
fI6yrrBnJFjdWAAQ4BkcEKBENRsY8NTs7jX5vnFA92MkUBby7BmariPDD3FtrB+f
Ob9B7CxM30pNqsN7OA/QvFOHMJHxf3s1TBKwmPHe5TLIfSzV1YxcEGiMc0lWqF4v
BT8ZeMGCtjDw94tND1DskfQQRPaMqPmGuRTrAW/IuE2n92bFtbqIqs7Cbw0fzLE=
=Vm6Q
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.8-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.8 - Take 2
Includes GSI routing support to go along with the new VGIC and a small fix that
has been cooking in -next for a while.
- GICv3 ITS emulation
- Simpler idmap management that fixes potential TLB conflicts
- Honor the kernel protection in HYP mode
- Removal of the old vgic implementation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2Del
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into next
KVM/ARM changes for Linux 4.8
- GICv3 ITS emulation
- Simpler idmap management that fixes potential TLB conflicts
- Honor the kernel protection in HYP mode
- Removal of the old vgic implementation
Up to now, only irqchip routing entries could be set. This patch
adds the capability to insert MSI routing entries.
For ARM64, let's also increase KVM_MAX_IRQ_ROUTES to 4096: this
include SPI irqchip routes plus MSI routes. In the future this
might be extended.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
kvm_setup_default_irq_routing and kvm_setup_empty_irq_routing are
not used by generic code. So let's move the declarations in x86 irq.h
header instead of kvm_host.h.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Enhance kvm_kernel_irq_routing_entry to transport the device id
field, devid. A new flags field makes possible to indicate the
devid is valid. Those additions are used for ARM GICv3 ITS MSI
injection. The original struct msi_msg msi field is replaced by
a new custom structure that embeds the new fields.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Suggested-by: Radim Krčmář <rkrcmar@redhat.com>
Acked-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
The kvm_io_bus framework is a nice place of holding information about
various MMIO regions for kernel emulated devices.
Add a call to retrieve the kvm_io_device structure which is associated
with a certain MMIO address. This avoids to duplicate kvm_io_bus'
knowledge of MMIO regions without having to fake MMIO calls if a user
needs the device a certain MMIO address belongs to.
This will be used by the ITS emulation to get the associated ITS device
when someone triggers an MSI via an ioctl from userspace.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Use the functions from context_tracking.h directly.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Make kvm_guest_{enter,exit} and __kvm_guest_{enter,exit} trivial wrappers
around the code in context_tracking.h. Name the context_tracking.h functions
consistently with what those for kernel<->user switch.
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The new created_vcpus field makes it possible to avoid the race between
irqchip and VCPU creation in a much nicer way; just check under kvm->lock
whether a VCPU has already been created.
We can then remove KVM_APIC_ARCHITECTURE too, because at this point the
symbol is only governing the default definition of kvm_vcpu_compatible.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The race between creating the irqchip and the first VCPU is
currently fixed by checking the presence of an irqchip before
updating kvm->online_vcpus, and undoing the whole VCPU creation
if someone created the irqchip in the meanwhile.
Instead, introduce a new field in struct kvm that will count VCPUs
under a mutex, without the atomic access and memory ordering that we
need elsewhere to protect the vcpus array. This also plugs the race
and is more easily applicable in all similar circumstances.
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds a kvm debugfs subdirectory for each VM, which is named
after its pid and file descriptor. The directories contain the same
kind of files that are already in the kvm debugfs directory, but the
data exported through them is now VM specific.
This makes the debugfs kvm data a convenient alternative to the
tracepoints which already have per VM data. The debugfs data is easy
to read and low overhead.
CC: Dan Carpenter <dan.carpenter@oracle.com> [includes fixes by Dan Carpenter]
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
AVIC has a use for kvm_vcpu_wake_up.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Some wakeups should not be considered a sucessful poll. For example on
s390 I/O interrupts are usually floating, which means that _ALL_ CPUs
would be considered runnable - letting all vCPUs poll all the time for
transactional like workload, even if one vCPU would be enough.
This can result in huge CPU usage for large guests.
This patch lets architectures provide a way to qualify wakeups if they
should be considered a good/bad wakeups in regard to polls.
For s390 the implementation will fence of halt polling for anything but
known good, single vCPU events. The s390 implementation for floating
interrupts does a wakeup for one vCPU, but the interrupt will be delivered
by whatever CPU checks first for a pending interrupt. We prefer the
woken up CPU by marking the poll of this CPU as "good" poll.
This code will also mark several other wakeup reasons like IPI or
expired timers as "good". This will of course also mark some events as
not sucessful. As KVM on z runs always as a 2nd level hypervisor,
we prefer to not poll, unless we are really sure, though.
This patch successfully limits the CPU usage for cases like uperf 1byte
transactional ping pong workload or wakeup heavy workload like OLTP
while still providing a proper speedup.
This also introduced a new vcpu stat "halt_poll_no_tuning" that marks
wakeups that are considered not good for polling.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Acked-by: Radim Krčmář <rkrcmar@redhat.com> (for an earlier version)
Cc: David Matlack <dmatlack@google.com>
Cc: Wanpeng Li <kernellwp@gmail.com>
[Rename config symbol. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If we don't support a mechanism for bypassing IRQs, don't register as
a consumer. This eliminates meaningless dev_info()s when the connect
fails between producer and consumer, such as on AMD systems where
kvm_x86_ops->update_pi_irte is not implemented
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The KVM_MAX_VCPUS define provides the maximum number of vCPUs per guest, and
also the upper limit for vCPU ids. This is okay for all archs except PowerPC
which can have higher ids, depending on the cpu/core/thread topology. In the
worst case (single threaded guest, host with 8 threads per core), it limits
the maximum number of vCPUS to KVM_MAX_VCPUS / 8.
This patch separates the vCPU numbering from the total number of vCPUs, with
the introduction of KVM_MAX_VCPU_ID, as the maximal valid value for vCPU ids
plus one.
The corresponding KVM_CAP_MAX_VCPU_ID allows userspace to validate vCPU ids
before passing them to KVM_CREATE_VCPU.
This patch only implements KVM_MAX_VCPU_ID with a specific value for PowerPC.
Other archs continue to return KVM_MAX_VCPUS instead.
Suggested-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Commit c896939f7c ("KVM: use heuristic for fast VCPU lookup by id") added
a return path that prevents vcpu ids to exceed KVM_MAX_VCPUS. This is a
problem for powerpc where vcpu ids can grow up to 8*KVM_MAX_VCPUS.
This patch simply reverses the logic so that we only try fast path if the
vcpu id can be tried as an index in kvm->vcpus[]. The slow path is not
affected by the change.
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_make_request and kvm_check_request imply a producer-consumer
relationship; add implicit memory barriers to them. There was indeed
already a place that was adding an explicit smp_mb() to order between
kvm_check_request and the processing of the request. That memory
barrier can be removed (as an added benefit, kvm_check_request can use
smp_mb__after_atomic which is free on x86).
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The problem:
On -rt, an emulated LAPIC timer instances has the following path:
1) hard interrupt
2) ksoftirqd is scheduled
3) ksoftirqd wakes up vcpu thread
4) vcpu thread is scheduled
This extra context switch introduces unnecessary latency in the
LAPIC path for a KVM guest.
The solution:
Allow waking up vcpu thread from hardirq context,
thus avoiding the need for ksoftirqd to be scheduled.
Normal waitqueues make use of spinlocks, which on -RT
are sleepable locks. Therefore, waking up a waitqueue
waiter involves locking a sleeping lock, which
is not allowed from hard interrupt context.
cyclictest command line:
This patch reduces the average latency in my tests from 14us to 11us.
Daniel writes:
Paolo asked for numbers from kvm-unit-tests/tscdeadline_latency
benchmark on mainline. The test was run 1000 times on
tip/sched/core 4.4.0-rc8-01134-g0905f04:
./x86-run x86/tscdeadline_latency.flat -cpu host
with idle=poll.
The test seems not to deliver really stable numbers though most of
them are smaller. Paolo write:
"Anything above ~10000 cycles means that the host went to C1 or
lower---the number means more or less nothing in that case.
The mean shows an improvement indeed."
Before:
min max mean std
count 1000.000000 1000.000000 1000.000000 1000.000000
mean 5162.596000 2019270.084000 5824.491541 20681.645558
std 75.431231 622607.723969 89.575700 6492.272062
min 4466.000000 23928.000000 5537.926500 585.864966
25% 5163.000000 1613252.750000 5790.132275 16683.745433
50% 5175.000000 2281919.000000 5834.654000 23151.990026
75% 5190.000000 2382865.750000 5861.412950 24148.206168
max 5228.000000 4175158.000000 6254.827300 46481.048691
After
min max mean std
count 1000.000000 1000.00000 1000.000000 1000.000000
mean 5143.511000 2076886.10300 5813.312474 21207.357565
std 77.668322 610413.09583 86.541500 6331.915127
min 4427.000000 25103.00000 5529.756600 559.187707
25% 5148.000000 1691272.75000 5784.889825 17473.518244
50% 5160.000000 2308328.50000 5832.025000 23464.837068
75% 5172.000000 2393037.75000 5853.177675 24223.969976
max 5222.000000 3922458.00000 6186.720500 42520.379830
[Patch was originaly based on the swait implementation found in the -rt
tree. Daniel ported it to mainline's version and gathered the
benchmark numbers for tscdeadline_latency test.]
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: linux-rt-users@vger.kernel.org
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1455871601-27484-4-git-send-email-wagi@monom.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To date, we have implemented two I/O usage models for persistent memory,
PMEM (a persistent "ram disk") and DAX (mmap persistent memory into
userspace). This series adds a third, DAX-GUP, that allows DAX mappings
to be the target of direct-i/o. It allows userspace to coordinate
DMA/RDMA from/to persistent memory.
The implementation leverages the ZONE_DEVICE mm-zone that went into
4.3-rc1 (also discussed at kernel summit) to flag pages that are owned
and dynamically mapped by a device driver. The pmem driver, after
mapping a persistent memory range into the system memmap via
devm_memremap_pages(), arranges for DAX to distinguish pfn-only versus
page-backed pmem-pfns via flags in the new pfn_t type.
The DAX code, upon seeing a PFN_DEV+PFN_MAP flagged pfn, flags the
resulting pte(s) inserted into the process page tables with a new
_PAGE_DEVMAP flag. Later, when get_user_pages() is walking ptes it keys
off _PAGE_DEVMAP to pin the device hosting the page range active.
Finally, get_page() and put_page() are modified to take references
against the device driver established page mapping.
Finally, this need for "struct page" for persistent memory requires
memory capacity to store the memmap array. Given the memmap array for a
large pool of persistent may exhaust available DRAM introduce a
mechanism to allocate the memmap from persistent memory. The new
"struct vmem_altmap *" parameter to devm_memremap_pages() enables
arch_add_memory() to use reserved pmem capacity rather than the page
allocator.
This patch (of 18):
The core has developed a need for a "pfn_t" type [1]. Move the existing
pfn_t in KVM to kvm_pfn_t [2].
[1]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002199.html
[2]: https://lists.01.org/pipermail/linux-nvdimm/2015-September/002218.html
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since the numbers now overlap, it makes sense to enumerate
them in asm/kvm_host.h rather than linux/kvm_host.h. Functions
that refer to architecture-specific requests are also moved
to arch/.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Leave room for 4 more arch-independent requests.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Suggested-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
[Takuya moved all subsequent constants to fill the void, but that
is useless in view of the following patches. So this change looks
nothing like the original. - Paolo]
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
It looks like this in action:
kvm [5197]: vcpu0, guest rIP: 0xffffffff810187ba unhandled rdmsr: 0xc001102
and helps to pinpoint quickly where in the guest we did the unsupported
thing.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Per Hyper-V specification (and as required by Hyper-V-aware guests),
SynIC provides 4 per-vCPU timers. Each timer is programmed via a pair
of MSRs, and signals expiration by delivering a special format message
to the configured SynIC message slot and triggering the corresponding
synthetic interrupt.
Note: as implemented by this patch, all periodic timers are "lazy"
(i.e. if the vCPU wasn't scheduled for more than the timer period the
timer events are lost), regardless of the corresponding configuration
MSR. If deemed necessary, the "catch up" mode (the timer period is
shortened until the timer catches up) will be implemented later.
Changes v2:
* Use remainder to calculate periodic timer expiration time
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The SynIC message protocol mandates that the message slot is claimed
by atomically setting message type to something other than HVMSG_NONE.
If another message is to be delivered while the slot is still busy,
message pending flag is asserted to indicate to the guest that the
hypervisor wants to be notified when the slot is released.
To make sure the protocol works regardless of where the message
sources are (kernel or userspace), clear the pending flag on SINT ACK
notification, and let the message sources compete for the slot again.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Haiyang Zhang <haiyangz@microsoft.com>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM creates debugfs files to export VM statistics to userland. To be
able to remove them on kvm exit it tracks the files' dentries.
Since their parent directory is also tracked and since each parent
direntry knows its children we can easily remove them by using
debugfs_remove_recursive(kvm_debugfs_dir). Therefore we don't
need the extra tracking in the kvm_stats_debugfs_item anymore.
Signed-off-by: Janosch Frank <frankja@linux.vnet.ibm.com>
Reviewed-By: Sascha Silbe <silbe@linux.vnet.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Usually, VCPU ids match the array index. So let's try a fast
lookup first before falling back to the slow iteration.
Suggested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
This patch makes kvm_is_visible_gfn return bool due to this particular
function only using either one or zero as its return value.
No functional change.
Signed-off-by: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A new vcpu exit is introduced to notify the userspace of the
changes in Hyper-V SynIC configuration triggered by guest writing to the
corresponding MSRs.
Changes v4:
* exit into userspace only if guest writes into SynIC MSR's
Changes v3:
* added KVM_EXIT_HYPERV types and structs notes into docs
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
SynIC (synthetic interrupt controller) is a lapic extension,
which is controlled via MSRs and maintains for each vCPU
- 16 synthetic interrupt "lines" (SINT's); each can be configured to
trigger a specific interrupt vector optionally with auto-EOI
semantics
- a message page in the guest memory with 16 256-byte per-SINT message
slots
- an event flag page in the guest memory with 16 2048-bit per-SINT
event flag areas
The host triggers a SINT whenever it delivers a new message to the
corresponding slot or flips an event flag bit in the corresponding area.
The guest informs the host that it can try delivering a message by
explicitly asserting EOI in lapic or writing to End-Of-Message (EOM)
MSR.
The userspace (qemu) triggers interrupts and receives EOM notifications
via irqfd with resampler; for that, a GSI is allocated for each
configured SINT, and irq_routing api is extended to support GSI-SINT
mapping.
Changes v4:
* added activation of SynIC by vcpu KVM_ENABLE_CAP
* added per SynIC active flag
* added deactivation of APICv upon SynIC activation
Changes v3:
* added KVM_CAP_HYPERV_SYNIC and KVM_IRQ_ROUTING_HV_SINT notes into
docs
Changes v2:
* do not use posted interrupts for Hyper-V SynIC AutoEOI vectors
* add Hyper-V SynIC vectors into EOI exit bitmap
* Hyper-V SyniIC SINT msr write logic simplified
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Actually kvm_arch_irq_routing_update() should be
kvm_arch_post_irq_routing_update() as it's called at the end
of irq routing update.
This renaming frees kvm_arch_irq_routing_update function name.
kvm_arch_irq_routing_update() weak function which will be used
to update mappings for arch-specific irq routing entries
(in particular, the upcoming Hyper-V synthetic interrupts).
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: qemu-devel@nongnu.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Let's provide a function to lookup a VCPU by id.
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
[split patch from refactoring patch]
VMX and SVM calculate the TSC scaling ratio in a similar logic, so this
patch generalizes it to a common TSC scaling function.
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
[Inline the multiplication and shift steps into mul_u64_u64_shr. Remove
BUG_ON. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The function is not used outside device assignment, and
kvm_arch_set_irq_inatomic has a different prototype. Move it here and
make it static to avoid confusion.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We do not want to do too much work in atomic context, in particular
not walking all the VCPUs of the virtual machine. So we want
to distinguish the architecture-specific injection function for irqfd
from kvm_set_msi. Since it's still empty, reuse the newly added
kvm_arch_set_irq and rename it to kvm_arch_set_irq_inatomic.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Includes a number of fixes for the arch-timer, introducing proper
level-triggered semantics for the arch-timers, a series of patches to
synchronously halt a guest (prerequisite for IRQ forwarding), some tracepoint
improvements, a tweak for the EL2 panic handlers, some more VGIC cleanups
getting rid of redundant state, and finally a stylistic change that gets rid of
some ctags warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOhgAAAoJEEtpOizt6ddyKS8H/2ZHMTPjo6yChnrusNWy4Qbr
6laPDlzL+g45oMQRwNL7GnM1deRftaxvT2Wi+X84D/6Y/BD6MPds4HgtBfuWcSZ1
CyRJ0Ot/zrxenucSuJuOjq+a9gdizdAczkbB1MfYDULJH8fb6D+7RYLo3zgh4Xo4
pla3L9U6gSWe+YopBjZtZH43m3fwiwSM/v+uHOTIcXrsbR+fEgx/EFSKmA/DUCuo
P5cFO/ceUGu7nATCexu5V82TgR2hvurrsR7mqfwY8YcF6HRM+NEOoS29xWC77v5S
u/F08TKuKQLv0YTEFTyLETI/oEeuC0cHtrRQBNf4+9kXEOzKyXaae0wR/I6X2Ss=
=GMNk
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Changes for v4.4-rc1
Includes a number of fixes for the arch-timer, introducing proper
level-triggered semantics for the arch-timers, a series of patches to
synchronously halt a guest (prerequisite for IRQ forwarding), some tracepoint
improvements, a tweak for the EL2 panic handlers, some more VGIC cleanups
getting rid of redundant state, and finally a stylistic change that gets rid of
some ctags warnings.
Conflicts:
arch/x86/include/asm/kvm_host.h
Some times it is useful for architecture implementations of KVM to know
when the VCPU thread is about to block or when it comes back from
blocking (arm/arm64 needs to know this to properly implement timers, for
example).
Therefore provide a generic architecture callback function in line with
what we do elsewhere for KVM generic-arch interactions.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Allow for arch-specific interrupt types to be set. For that, add
kvm_arch_set_irq() which takes interrupt type-specific action if it
recognizes the interrupt type given, and -EWOULDBLOCK otherwise.
The default implementation always returns -EWOULDBLOCK.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Factor out kvm_notify_acked_gsi() helper to iterate over EOI listeners
and notify those matching the given gsi.
It will be reused in the upcoming Hyper-V SynIC implementation.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Vitaly Kuznetsov <vkuznets@redhat.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
CC: Gleb Natapov <gleb@kernel.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch updates the Posted-Interrupts Descriptor when vCPU
is blocked.
pre-block:
- Add the vCPU to the blocked per-CPU list
- Set 'NV' to POSTED_INTR_WAKEUP_VECTOR
post-block:
- Remove the vCPU from the per-CPU list
Signed-off-by: Feng Wu <feng.wu@intel.com>
[Concentrate invocation of pre/post-block hooks to vcpu_block. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds an arch specific hooks 'arch_update' in
'struct kvm_kernel_irqfd'. On Intel side, it is used to
update the IRTE when VT-d posted-interrupts is used.
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch introduces
- kvm_arch_irq_bypass_add_producer
- kvm_arch_irq_bypass_del_producer
- kvm_arch_irq_bypass_stop
- kvm_arch_irq_bypass_start
They make possible to specialize the KVM IRQ bypass consumer in
case CONFIG_KVM_HAVE_IRQ_BYPASS is set.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
[Add weak implementations of the callbacks. - Feng]
Signed-off-by: Feng Wu <feng.wu@intel.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
HV_X64_MSR_RESET msr is used by Hyper-V based Windows guest
to reset guest VM by hypervisor.
Necessary to support loading of winhv.sys in guest, which in turn is
required to support Windows VMBus.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In order to support a userspace IOAPIC interacting with an in kernel
APIC, the EOI exit bitmaps need to be configurable.
If the IOAPIC is in userspace (i.e. the irqchip has been split), the
EOI exit bitmaps will be set whenever the GSI Routes are configured.
In particular, for the low MSI routes are reservable for userspace
IOAPICs. For these MSI routes, the EOI Exit bit corresponding to the
destination vector of the route will be set for the destination VCPU.
The intention is for the userspace IOAPICs to use the reservable MSI
routes to inject interrupts into the guest.
This is a slight abuse of the notion of an MSI Route, given that MSIs
classically bypass the IOAPIC. It might be worthwhile to add an
additional route type to improve clarity.
Compile tested for Intel x86.
Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Adds KVM_EXIT_IOAPIC_EOI which allows the kernel to EOI
level-triggered IOAPIC interrupts.
Uses a per VCPU exit bitmap to decide whether or not the IOAPIC needs
to be informed (which is identical to the EOI_EXIT_BITMAP field used
by modern x86 processors, but can also be used to elide kvm IOAPIC EOI
exits on older processors).
[Note: A prototype using ResampleFDs found that decoupling the EOI
from the VCPU's thread made it possible for the VCPU to not see a
recent EOI after reentering the guest. This does not match real
hardware.]
Compile tested for Intel x86.
Signed-off-by: Steve Rutherford <srutherford@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
First patch in a series which enables the relocation of the
PIC/IOAPIC to userspace.
Adds capability KVM_CAP_SPLIT_IRQCHIP;
KVM_CAP_SPLIT_IRQCHIP enables the construction of LAPICs without the
rest of the irqchip.
Compile tested for x86.
Signed-off-by: Steve Rutherford <srutherford@google.com>
Suggested-by: Andrew Honig <ahonig@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Change halt_poll_ns into per-VCPU variable, seeded from module parameter,
to allow greater flexibility.
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Sending of notification is done by exiting vcpu to user space
if KVM_REQ_HV_CRASH is enabled for vcpu. At exit to user space
the kvm_run structure contains system_event with type
KVM_SYSTEM_EVENT_CRASH to notify about guest crash occurred.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
vcpu_debug is useful macro like kvm_debug but additionally
includes vcpu context inside output.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
Reviewed-by: Peter Hornyack <peterhornyack@google.com>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
If there are no assigned devices, the guest PAT are not providing
any useful information and can be overridden to writeback; VMX
always does this because it has the "IPAT" bit in its extended
page table entries, but SVM does not have anything similar.
Hook into VFIO and legacy device assignment so that they
provide this information to KVM.
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Tested-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Only two ioctls have to be modified; the address space id is
placed in the higher 16 bits of their slot id argument.
As of this patch, no architecture defines more than one
address space; x86 will be the first.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
We need to hide SMRAM from guests not running in SMM. Therefore, all
uses of kvm_read_guest* and kvm_write_guest* must be changed to use
different address spaces, depending on whether the VCPU is in system
management mode. We need to introduce a new family of functions for
this purpose.
For now, the VCPU-based functions have the same behavior as the
existing per-VM ones, they just accept a different type for the
first argument. Later however they will be changed to use one of many
"struct kvm_memslots" stored in struct kvm, through an architecture hook.
VM-based functions will unconditionally use the first memslots pointer.
Whenever possible, this patch introduces slot-based functions with an
__ prefix, with two wrappers for generic and vcpu-based actions.
The exceptions are kvm_read_guest and kvm_write_guest, which are copied
into the new functions kvm_vcpu_read_guest and kvm_vcpu_write_guest.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This patch adds the interface between x86.c and the emulator: the
SMBASE register, a new emulator flag, the RSM instruction. It also
adds a new request bit that will be used by the KVM_SMI ioctl.
Reviewed-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The memory slot is already available from gfn_to_memslot_dirty_bitmap.
Isn't it a shame to look it up again? Plus, it makes gfn_to_page_many_atomic
agnostic of multiple VCPU address spaces.
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This lets the function access the new memory slot without going through
kvm_memslots and id_to_memslot. It will simplify the code when more
than one address space will be supported.
Unfortunately, the "const"ness of the new argument must be casted
away in two places. Fixing KVM to accept const struct kvm_memory_slot
pointers would require modifications in pretty much all architectures,
and is left for later.
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Architecture-specific helpers are not supposed to muck with
struct kvm_userspace_memory_region contents. Add const to
enforce this.
In order to eliminate the only write in __kvm_set_memory_region,
the cleaning of deleted slots is pulled up from update_memslots
to __kvm_set_memory_region.
Reviewed-by: Takuya Yoshikawa <yoshikawa_takuya_b1@lab.ntt.co.jp>
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
gfn_to_pfn_async is used in just one place, and because of x86-specific
treatment that place will need to look at the memory slot. Hence inline
it into try_async_pf and export __gfn_to_pfn_memslot.
The patch also switches the subsequent call to gfn_to_pfn_prot to use
__gfn_to_pfn_memslot. This is a small optimization. Finally, remove
the now-unused async argument of __gfn_to_pfn.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Currently KVM will clear the FPU bits in CR0.TS in the VMCS, and trap to
re-load them every time the guest accesses the FPU after a switch back into
the guest from the host.
This patch copies the x86 task switch semantics for FPU loading, with the
FPU loaded eagerly after first use if the system uses eager fpu mode,
or if the guest uses the FPU frequently.
In the latter case, after loading the FPU for 255 times, the fpu_counter
will roll over, and we will revert to loading the FPU on demand, until
it has been established that the guest is still actively using the FPU.
This mirrors the x86 task switch policy, which seems to work.
Signed-off-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Several kvm architectures disable interrupts before kvm_guest_enter.
kvm_guest_enter then uses local_irq_save/restore to disable interrupts
again or for the first time. Lets provide underscore versions of
kvm_guest_{enter|exit} that assume being called locked.
kvm_guest_enter now disables interrupts for the full function and
thus we can remove the check for preemptible.
This patch then adopts s390/kvm to use local_irq_disable/enable calls
which are slighty cheaper that local_irq_save/restore and call these
new functions.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull NOHZ changes from Ingo Molnar:
"This tree adds full dynticks support to KVM guests (support the
disabling of the timer tick on the guest). The main missing piece was
the recognition of guest execution as RCU extended quiescent state and
related changes"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kvm,rcu,nohz: use RCU extended quiescent state when running KVM guest
context_tracking: Export context_tracking_user_enter/exit
context_tracking: Run vtime_user_enter/exit only when state == CONTEXT_USER
context_tracking: Add stub context_tracking_is_enabled
context_tracking: Generalize context tracking APIs to support user and guest
context_tracking: Rename context symbols to prepare for transition state
ppc: Remove unused cpp symbols in kvm headers
After reset, the CPU can change the BSP, which will be used upon INIT. Reset
should return the BSP which QEMU asked for, and therefore handled accordingly.
To quote: "If the MP protocol has completed and a BSP is chosen, subsequent
INITs (either to a specific processor or system wide) do not cause the MP
protocol to be repeated."
[Intel SDM 8.4.2: MP Initialization Protocol Requirements and Restrictions]
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Message-Id: <1427933438-12782-3-git-send-email-namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This is needed in e.g. ARM vGIC emulation, where the MMIO handling
depends on the VCPU that does the access.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Introduce __KVM_HAVE_ARCH_INTC_INITIALIZED define and
associated kvm_arch_intc_initialized function. This latter
allows to test whether the virtual interrupt controller is initialized
and ready to accept virtual IRQ injection. On some architectures,
the virtual interrupt controller is dynamically instantiated, justifying
that kind of check.
The new function can now be used by irqfd to check whether the
virtual interrupt controller is ready on KVM_IRQFD request. If not,
KVM_IRQFD returns -EAGAIN.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
kvm_kvfree() provides exactly the same functionality as the
new common kvfree() function - so let's simply replace the
kvm function with the common function.
Signed-off-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
The host kernel is not doing anything while the CPU is executing
a KVM guest VCPU, so it can be marked as being in an extended
quiescent state, identical to that used when running user space
code.
The only exception to that rule is when the host handles an
interrupt, which is already handled by the irq code, which
calls rcu_irq_enter and rcu_irq_exit.
The guest_enter and guest_exit functions already switch vtime
accounting independent of context tracking. Leave those calls
where they are, instead of moving them into the context tracking
code.
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Will deacon <will.deacon@arm.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Common: Optional support for adding a small amount of polling on each HLT
instruction executed in the guest (or equivalent for other architectures).
This can improve latency up to 50% on some scenarios (e.g. O_DSYNC writes
or TCP_RR netperf tests). This also has to be enabled manually for now,
but the plan is to auto-tune this in the future.
ARM/ARM64: the highlights are support for GICv3 emulation and dirty page
tracking
s390: several optimizations and bugfixes. Also a first: a feature
exposed by KVM (UUID and long guest name in /proc/sysinfo) before
it is available in IBM's hypervisor! :)
MIPS: Bugfixes.
x86: Support for PML (page modification logging, a new feature in
Broadwell Xeons that speeds up dirty page tracking), nested virtualization
improvements (nested APICv---a nice optimization), usual round of emulation
fixes. There is also a new option to reduce latency of the TSC deadline
timer in the guest; this needs to be tuned manually.
Some commits are common between this pull and Catalin's; I see you
have already included his tree.
ARM has other conflicts where functions are added in the same place
by 3.19-rc and 3.20 patches. These are not large though, and entirely
within KVM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJU28rkAAoJEL/70l94x66DXqQH/1TDOfJIjW7P2kb0Sw7Fy1wi
cEX1KO/VFxAqc8R0E/0Wb55CXyPjQJM6xBXuFr5cUDaIjQ8ULSktL4pEwXyyv/s5
DBDkN65mriry2w5VuEaRLVcuX9Wy+tqLQXWNkEySfyb4uhZChWWHvKEcgw5SqCyg
NlpeHurYESIoNyov3jWqvBjr4OmaQENyv7t2c6q5ErIgG02V+iCux5QGbphM2IC9
LFtPKxoqhfeB2xFxTOIt8HJiXrZNwflsTejIlCl/NSEiDVLLxxHCxK2tWK/tUXMn
JfLD9ytXBWtNMwInvtFm4fPmDouv2VDyR0xnK2db+/axsJZnbxqjGu1um4Dqbak=
=7gdx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM update from Paolo Bonzini:
"Fairly small update, but there are some interesting new features.
Common:
Optional support for adding a small amount of polling on each HLT
instruction executed in the guest (or equivalent for other
architectures). This can improve latency up to 50% on some
scenarios (e.g. O_DSYNC writes or TCP_RR netperf tests). This
also has to be enabled manually for now, but the plan is to
auto-tune this in the future.
ARM/ARM64:
The highlights are support for GICv3 emulation and dirty page
tracking
s390:
Several optimizations and bugfixes. Also a first: a feature
exposed by KVM (UUID and long guest name in /proc/sysinfo) before
it is available in IBM's hypervisor! :)
MIPS:
Bugfixes.
x86:
Support for PML (page modification logging, a new feature in
Broadwell Xeons that speeds up dirty page tracking), nested
virtualization improvements (nested APICv---a nice optimization),
usual round of emulation fixes.
There is also a new option to reduce latency of the TSC deadline
timer in the guest; this needs to be tuned manually.
Some commits are common between this pull and Catalin's; I see you
have already included his tree.
Powerpc:
Nothing yet.
The KVM/PPC changes will come in through the PPC maintainers,
because I haven't received them yet and I might end up being
offline for some part of next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (130 commits)
KVM: ia64: drop kvm.h from installed user headers
KVM: x86: fix build with !CONFIG_SMP
KVM: x86: emulate: correct page fault error code for NoWrite instructions
KVM: Disable compat ioctl for s390
KVM: s390: add cpu model support
KVM: s390: use facilities and cpu_id per KVM
KVM: s390/CPACF: Choose crypto control block format
s390/kernel: Update /proc/sysinfo file with Extended Name and UUID
KVM: s390: reenable LPP facility
KVM: s390: floating irqs: fix user triggerable endless loop
kvm: add halt_poll_ns module parameter
kvm: remove KVM_MMIO_SIZE
KVM: MIPS: Don't leak FPU/DSP to guest
KVM: MIPS: Disable HTW while in guest
KVM: nVMX: Enable nested posted interrupt processing
KVM: nVMX: Enable nested virtual interrupt delivery
KVM: nVMX: Enable nested apic register virtualization
KVM: nVMX: Make nested control MSRs per-cpu
KVM: nVMX: Enable nested virtualize x2apic mode
KVM: nVMX: Prepare for using hardware MSR bitmap
...
Use the more generic get_user_pages_unlocked which has the additional
benefit of passing FAULT_FLAG_ALLOW_RETRY at the very first page fault
(which allows the first page fault in an unmapped area to be always able
to block indefinitely by being allowed to release the mmap_sem).
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Reviewed-by: Andres Lagar-Cavilla <andreslc@google.com>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Peter Feiner <pfeiner@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We don't have to write protect guest memory for dirty logging if architecture
supports hardware dirty logging, such as PML on VMX, so rename it to be more
generic.
Signed-off-by: Kai Huang <kai.huang@linux.intel.com>
Reviewed-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
1. Generic
- sparse warning (make function static)
- optimize locking
- bugfixes for interrupt injection
- fix MVPG addressing modes
2. hrtimer/wakeup fun
A recent change can cause KVM hangs if adjtime is used in the host.
The hrtimer might wake up too early or too late. Too early is fatal
as vcpu_block will see that the wakeup condition is not met and
sleep again. This CPU might never wake up again.
This series addresses this problem. adjclock slowing down the host
clock will result in too late wakeups. This will require more work.
In addition to that we also change the hrtimer from REALTIME to
MONOTONIC to avoid similar problems with timedatectl set-time.
3. sigp rework
We will move all "slow" sigps to QEMU (protected with a capability that
can be enabled) to avoid several races between concurrent SIGP orders.
4. Optimize the shadow page table
Provide an interface to announce the maximum guest size. The kernel
will use that to make the pagetable 2,3,4 (or theoretically) 5 levels.
5. Provide an interface to set the guest TOD
We now use two vm attributes instead of two oneregs, as oneregs are
vcpu ioctl and we don't want to call them from other threads.
6. Protected key functions
The real HMC allows to enable/disable protected key CPACF functions.
Lets provide an implementation + an interface for QEMU to activate
this the protected key instructions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)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=zLjR
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-next-20150122' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into kvm-next
KVM: s390: fixes and features for kvm/next (3.20)
1. Generic
- sparse warning (make function static)
- optimize locking
- bugfixes for interrupt injection
- fix MVPG addressing modes
2. hrtimer/wakeup fun
A recent change can cause KVM hangs if adjtime is used in the host.
The hrtimer might wake up too early or too late. Too early is fatal
as vcpu_block will see that the wakeup condition is not met and
sleep again. This CPU might never wake up again.
This series addresses this problem. adjclock slowing down the host
clock will result in too late wakeups. This will require more work.
In addition to that we also change the hrtimer from REALTIME to
MONOTONIC to avoid similar problems with timedatectl set-time.
3. sigp rework
We will move all "slow" sigps to QEMU (protected with a capability that
can be enabled) to avoid several races between concurrent SIGP orders.
4. Optimize the shadow page table
Provide an interface to announce the maximum guest size. The kernel
will use that to make the pagetable 2,3,4 (or theoretically) 5 levels.
5. Provide an interface to set the guest TOD
We now use two vm attributes instead of two oneregs, as oneregs are
vcpu ioctl and we don't want to call them from other threads.
6. Protected key functions
The real HMC allows to enable/disable protected key CPACF functions.
Lets provide an implementation + an interface for QEMU to activate
this the protected key instructions.
The return value of kvm_arch_vcpu_postcreate is not checked in its
caller. This is okay, because only x86 provides vcpu_postcreate right
now and it could only fail if vcpu_load failed. But that is not
possible during KVM_CREATE_VCPU (kvm_arch_vcpu_load is void, too), so
just get rid of the unchecked return value.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
With everything separated and prepared, we implement a model of a
GICv3 distributor and redistributors by using the existing framework
to provide handler functions for each register group.
Currently we limit the emulation to a model enforcing a single
security state, with SRE==1 (forcing system register access) and
ARE==1 (allowing more than 8 VCPUs).
We share some of the functions provided for GICv2 emulation, but take
the different ways of addressing (v)CPUs into account.
Save and restore is currently not implemented.
Similar to the split-off of the GICv2 specific code, the new emulation
code goes into a new file (vgic-v3-emul.c).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Currently we unconditionally register the GICv2 emulation device
during the host's KVM initialization. Since with GICv3 support we
may end up with only v2 or only v3 or both supported, we move the
registration into the GIC probing function, where we will later know
which combination is valid.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
kvm_get_dirty_log() provides generic handling of dirty bitmap, currently reused
by several architectures. Building on that we intrdoduce
kvm_get_dirty_log_protect() adding write protection to mark these pages dirty
for future write access, before next KVM_GET_DIRTY_LOG ioctl call from user
space.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Mario Smarduch <m.smarduch@samsung.com>
problems, clarifies VCPU init, and fixes a regression concerning the
VGIC init flow.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUjsVhAAoJEEtpOizt6ddy5rIH/1V/YVwhprC55YqdHelU9Qu2
Muzsx+7F71NxC7xgMGFqPD1YrPR+hxvoPhy+ADOBlvcqlolrkDnV9I+8e3geaYNc
nZ/yEnoGTtbAggiS1smx7usBv34Z88Sd5txNjmj1cmHBy+VOWlyidWMkGBTsfBRe
mVc61BDUfyC47udgRHXhwS80sbHLJHElmADisFOVmQNBYwwiHiTdx0hMBMnHcC3Y
/3T0tKxHdeTISnmA+J+n7TcChtTIM4xqC6kwf3rw3b7XX8gdtTKylDHX2GLAg646
RdebAG2twmGpIc6SxXZbo38f3oY9OFo1Le5xZGa6iUjD56VDw/e4wg4iA2juo0Y=
=J2Ut
-----END PGP SIGNATURE-----
Merge tag 'kvm-arm-for-3.19-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
Second round of changes for KVM for arm/arm64 for v3.19; fixes reboot
problems, clarifies VCPU init, and fixes a regression concerning the
VGIC init flow.
Conflicts:
arch/ia64/kvm/kvm-ia64.c [deleted in HEAD and modified in kvmarm]
Current linear search doesn't scale well when
large amount of memslots is used and looked up slot
is not in the beginning memslots array.
Taking in account that memslots don't overlap, it's
possible to switch sorting order of memslots array from
'npages' to 'base_gfn' and use binary search for
memslot lookup by GFN.
As result of switching to binary search lookup times
are reduced with large amount of memslots.
Following is a table of search_memslot() cycles
during WS2008R2 guest boot.
boot, boot + ~10 min
mostly same of using it,
slot lookup randomized lookup
max average average
cycles cycles cycles
13 slots : 1450 28 30
13 slots : 1400 30 40
binary search
117 slots : 13000 30 460
117 slots : 2000 35 180
binary search
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In typical guest boot workload only 2-3 memslots are used
extensively, and at that it's mostly the same memslot
lookup operation.
Adding LRU cache improves average lookup time from
46 to 28 cycles (~40%) for this workload.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Memory regions may be incoherent with the caches, typically when the
guest has mapped a host system RAM backed memory region as uncached.
Add a flag KVM_MEMSLOT_INCOHERENT so that we can tag these memslots
and handle them appropriately when mapping them.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Create a new header, and hide the device assignment functions there.
Move struct kvm_assigned_dev_kernel to assigned-dev.c by modifying
arch/x86/kvm/iommu.c to take a PCI device struct.
Based on a patch by Radim Krcmar <rkrcmark@redhat.com>.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Now that ia64 is gone, we can hide deprecated device assignment in x86.
Notable changes:
- kvm_vm_ioctl_assigned_device() was moved to x86/kvm_arch_vm_ioctl()
The easy parts were removed from generic kvm code, remaining
- kvm_iommu_(un)map_pages() would require new code to be moved
- struct kvm_assigned_dev_kernel depends on struct kvm_irq_ack_notifier
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
ia64 does not need them anymore. Ack notifiers become x86-specific
too.
Suggested-by: Gleb Natapov <gleb@kernel.org>
Reviewed-by: Radim Krcmar <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>