Only need to do surface flip for video plane via dmcub.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently if seamless boot is enabled, we will skip double buffer enable
for OTG_BLANK. However, we need the double buffer enable in order to
block global sync signals when OTG becomes blanked (for PSR). Blocking
global sync signals prevent pipe from requesting data.
[How]
Move tg_init before seamless boot check.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dpcd cap mismatch in 2200 vs base
[How]
Add monitor patch which using based caps to overwrite 2200
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently we wait for test pattern after each pipe is programmed. For
ODM combined scenario it will cause test pattern is shown on only half
screen for 1 frame. This is not desirable.
[how]
No wait between odm pipe programming, only wait after all pipes are
programmed.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With different refresh rate panels, the PSR entry/exit time is
different since it is dependent on 2 frame entry time today
[How]
Make static screen num frame entry time to be calculated
such that entry time is within 30 ms instead of fixed num
frames.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCU need to wait a vblank to handle psr enter command. When psr exit
coming before vblank, the psr exit command will be skip because current
psr state is disable.
[How]
remove psr state condition when psr exit case
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
IRAM definition needed for versions of DMCU containing ABM 2.4
[How]
Pass ABM 2.3 IRAM definition, which is compatible with ABM 2.4, to DMCU
when ABM 2.4 FW is detected
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DML Initialization was previously done on dcn21_resource initialization.
This meant that DML soc struct was populated with hardcoded values.
[How]
Move DML initialization to after updating bounding box, to use clock table
values from SMU.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PHY will sometimes be in bad state on hotplugging display from USB-C
dongle.
[How]
Add additional calls to disable and then enable PHY before link training
starts during verify_link_cap.
Signed-off-by: George Shen <george.shen@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DMUB PSR command IDs do not have the correct values.
[How]
Fix the command IDs and cleanup the formatting.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Rework surface programming for RN to separate preparing parameters and
register programming.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recent double buffering changes for dcn2 use IX_REG_READ.
However, this macro returns the full register value, with the need to
manually shift and mask it to retrieve field data.
[How]
Create new IX_REG_GET macro that handles shift and mask.
Use this for double buffering reads instead of IX_REG_READ.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Moving PSR from DMCU to DMCUB.
[How]
Cleanup psr spec files and add PSR hw programming files.
No functionality is included in this change.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Programming surface flip addresses via dmcub uC for optimizing the data
flush.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting color temperature, screen tearing was observed.
This was due to overwritten values in gamut remap registers.
This issue was solved for OCSC and ICSC by alternating between "A" and
"B" registers to double buffer the writes.
[How]
Create new set_gamut_remap and program_gamut_remap for dcn20.
Alternate which registers are written to by switching modes each time.
Also fixes ICSC mode reg read to use proper data offset.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Moving PSR from DMCU to DMCUB.
[How]
Add driverside PSR changes required to send inbox messages to fw.
These changes are non-functional until the psr structure allocation
is uncommented.
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting video brightness, screen tearing was observed.
This was due to overwritten values in ICSC registers. In dcn10, this issue had been
fixed by implementing double buffering via alternating ICSC modes.
However, the second register set used in dcn1 doesn't exist in dcn2.
[How]
Create new program_input_csc for dcn20.
Use ICSC_B registers instead of COMA registers as second set.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add more fields to support upcoming dml versions
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Don't want to start HW discovery unless we have lost power,
as doing rediscovery otherwise is both unnecessary and time consuming.
Before this change it takes 40 seconds to go in to suspend, after it
takes 27 seconds
[How]
Accelerated mode gets cleared if we lose power. Only do detection if
this register is cleared
Signed-off-by: Joseph Gravenor <joseph.gravenor@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Test pattern should be applied to hardware when exiting set test pattern
function.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
48mhz turn off feature does not work on HDMI and DVI, but the feauture
was only blocked on HDMI, this change will apply the same wa on DVI
[HOW]
Apply workaround for all TMDS signal types (HDMI, DVI single/dual link)
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If dummy pstate latency is 0 we should report the actual
pstate support, and not that pstate is always supported.
[How]
Don't always program pstate support true
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make sure that lttpr_caps has the mode set to repeater.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When rapidly adjusting colour properties (e.g. brightness), screen tearing was observed.
This was due to overwritten values in OCSC registers. In dcn10, this issue had been fixed by
implementing double buffering by alternating OCSC modes.
[How]
Alternate which OCSC registers are used by switching modes each time.
This double buffers the CSC writes.
Signed-off-by: Noah Abradjian <noah.abradjian@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We need to ensure that the DMUIF in MMHUBBUB is also in reset so we
aren't generating requests while the DMCUB is in reset.
[How]
Set DMUIF_SOFT_RESET=1 on reset and DMUIF_SOFT_RESET=0 on reset
release.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The inst firmware isn't necessarily fully flushed to framebuffer
memory and the DMCUB can hang due to invalid inst being parsed.
[How]
Like the fix to flush ringbuffer commands before updating the inbox
write pointer we need to read back inst memory before writing the
CW0 registers.
Add a helper to read 64-byte chunks to avoid a large temporary buffer.
Read the remaining leftover bytes if the inst_fb isn't fully aligned.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There's a data race that can occur between when we update the
inbox write pointer vs when the memory for the command actually gets
flushed from the map to the framebuffer.
DMCUB can read stale or partially invalid data when this race occurs.
[How]
Before updating the write pointer we can read back all pending commands
to ensure that we stall for the writes to be flushed to framebuffer.
We don't need to worry about choosing HDP vs VM flush with this
mechanism.
Drop the dmub_srv_cmd_submit() while we're updating this to work
correctly since nothing was actually using this API and the caller
should be explicit about the API flow here - by doing this on execute
we can give some extra time for the flush to finish while
preparing other commands.
We should try to avoid writing single commands
because of this overhead.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
While doing seamless boot I made some changes
to dcn2 hubbub functions, missed a link
[how]
link hubbub1 func to hubbub2 usage. It has already
been successfully linked in dcn1 and 3.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If the specific monitor supports DSC, the secondary link should be
disabled, and the other way around, too: if either that monitor or
our ASIC doesn't support DSC, the secodary link should be enabled.
[how]
Add a monitor patch and disable secondary link if that monitor
is detected and if ASIC supports DSC, or otherwise enable secondary
link.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Needed to reprogram vblank_start in dml properly in order to get the
correct dlg params to program VTG.
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous implementation we may have residual chroma address offset
if transition from wa enable -> wa disable.
[How]
Clear address offset cache when viewport updates. Also update the
vp size check condition to account for rotation angle
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Upon exiting a fixed active VRR state, the state isn't cleared. This
leads to the variable VRR range to be calculated incorrectly.
[how]
Set fixed active state to false when updating vrr params
Signed-off-by: Amanda Liu <amanda.liu@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add registers for handling Post Gamma Color Blending (OCSC), which is
useful for conversion from RGB->YUV for HDMI.
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This also replaces old artifacts with a correct one in drm_sched_entity_init()
declaration
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
support check if dirver should try gpu recovery for
arcturus
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To allow the flexibilty for user to disable gpu recovery
in RAS recovery path by module parameter amdgpu_gpu_recovery
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The mec ucode will set the CP_HQD_ACTIVE bit while the queue is mapped by
MAP_QUEUES packet. So we only need set cp active field for kiq queue.
Signed-off-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SW scheduler is previously called non HW scheduler, or non HWS. This
message is useful when triaging issues from dmesg.
Signed-off-by: Yong Zhao <Yong.Zhao@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch uses score based logic to select a new rq for better
loadbalance between multiple rq/scheds instead of num_jobs.
Below are test results after running amdgpu_test from mesa drm
Before this patch:
sched_name num of many times it got scheduled
========= ==================================
sdma0 314
sdma1 32
comp_1.0.0 56
comp_1.0.1 0
comp_1.1.0 0
comp_1.1.1 0
comp_1.2.0 0
comp_1.2.1 0
comp_1.3.0 0
comp_1.3.1 0
After this patch:
sched_name num of many times it got scheduled
========= ==================================
sdma0 216
sdma1 185
comp_1.0.0 39
comp_1.0.1 9
comp_1.1.0 12
comp_1.1.1 0
comp_1.2.0 12
comp_1.2.1 0
comp_1.3.0 12
comp_1.3.1 0
Signed-off-by: Nirmoy Das <nirmoy.das@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Implement indirect DPG SRAM mode for vcn2.5
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add dpg pause mode support for vcn2.5
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DPG mode start and stop functions for vcn2.5
v2: Correct firmware ucode index in vcn_v2_5_mc_resume_dpg_mode
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move macro from vcn2.0 to amdgpu_vcn to share with vcn2.5
v2: squash in macro fix
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
