GPIOlib will print warning messages if we call GPIO functions without a
valid GPIO. Change the code to avoid doing so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes two BUG_ON() used to notify about RX queue corruptions
on macb (not gem) hardware without actually handling the error.
The new code skips corrupted frames but still processes faultless frames.
Then it resets the RX queue before restarting the reception from a clean
state.
This patch is a rework of an older patch proposed by Neil Armstrong:
http://patchwork.ozlabs.org/patch/371525/
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_interrupt() should not use macb_writel(bp, ISR, <value>) but only
queue_writel(queue, ISR, <value>).
There is one IRQ and one set of {ISR, IER, IDR, IMR} [1] registers per
queue on gem hardware, though only queue0 is actually used for now to
receive frames: other queues can already be used to transmit frames.
The queue_readl() and queue_writel() helper macros are designed to access
the relevant IRQ registers.
[1]
ISR: Interrupt Status Register
IER: Interrupt Enable Register
IDR: Interrupt Disable Register
IMR: Interrupt Mask Register
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: bfbb92c446 ("net: macb: Handle the RXUBR interrupt on all devices")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls gpiod_set_value() with GPIOD_OUT_* instead of 0 and 1, as
a result the PHY isn't really put back into reset state in macb_remove().
Moreover, the driver assumes that something else has set the GPIO direction
to output, so if it has not, the PHY may not be taken out of reset in
macb_probe() either...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As requested by Rob Herring on patch
https://patchwork.ozlabs.org/patch/580862/.
This is a new property that it's still in net-next and has never been
used in production, so we are not breaking anything with the
incompatible binding change.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are getting build warning about:
macb.c:2889:13: warning: 'tx_clk' may be used uninitialized in this function
macb.c:2888:11: warning: 'hclk' may be used uninitialized in this function
In reality they are not used uninitialized as clk_init() will initialize
them, this patch will just silence the warning.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling interrupts with the IDR register does not stop the macb hardware
from asserting its interrupt line if there are interrupts pending. Always
clear the interrupts using ISR, and be sure to write it on hardware that
is not read-to-clear, like Zynq. Not doing so will cause interrupts when
the driver doesn't expect them.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare a new NP4 SoC variant having USRIO_DISABLED as capability bit.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, the macb integration does not use the USRIO
register to configure the (R)MII port and clocks.
When the register is not implemented and the MACB error signal
is connected to the bus error, reading or writing to the USRIO
register can trigger some Imprecise External Aborts on ARM platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of being at the MAC level the reset gpio preperty is moved at the
PHY child node level. It is still managed by the MAC, but from the point
of view of the binding it make more sense to be part of the PHY node.
This commit also fixes a build errors if GPIOLIB is not selected.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allow to power down the PHY when
the network interface is no more used.
This reset can't be done at the PHY driver level. The PHY must be able to
answer the to the mii bus scan to let the kernel creating a PHY device.
The patch introduces a new optional property "phy-reset-gpios" inspired
from the one use for the FEC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the sgmii phy interface.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If an architecture defines readl/writel using CPP macros, we
get the following kinds of build failure:
> > > drivers/net/ethernet/cadence/macb.c:164:1: error: macro "writel"
> > > passed 3 arguments, but takes just 2
> macb_or_gem_writel(bp, SA1B, bottom);
> ^
Rename the methods so that this doesn't happen.
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_count_tx_descriptors() repeats the generic macro DIV_ROUND_UP(). The patch
does a replacement.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warnings:
drivers/net/ethernet/cadence/macb.c: In function ‘macb_handle_link_change’:
drivers/net/ethernet/cadence/macb.c:266: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:267: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:291: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_update_stats’:
drivers/net/ethernet/cadence/macb.c:1908: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_get_ethtool_strings’:
drivers/net/ethernet/cadence/macb.c:1988: warning: comparison between signed and unsigned
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid messages like
macb macb.0 (unnamed net_device) (uninitialized): Cadence caps 0x00000000
macb macb.0 (unnamed net_device) (uninitialized): invalid hw address, using random
let's use dev_*() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 98b5a0f4a2 introduces jumbo frame support, but also it assumes
that macb_config present which is not always true.
The configuration without macb_config fails to boot.
Unable to handle kernel NULL pointer dereference at virtual address 00000010
ptbr = 90350000 pgd = 00000000
Oops: Kernel access of bad area, sig: 11 [#1]
FRAME_POINTER chip: 0x01f:0x1e82 rev 2
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.2.0-rc3-next-20150723+ #13
task: 91c26000 ti: 91c28000 task.ti: 91c28000
PC is at macb_probe+0x140/0x61c
Fixes: 98b5a0f4a2 (net: macb: Add support for jumbo frames)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit a50dad355a (net: macb: Add big endian CPU support) converted I/O
accessors to readl_relaxed() and writel_relaxed() and consequentially broke
MACB driver on AVR32 platforms such as ATNGW100.
This patch improves I/O access by checking endiannes first and use the
corresponding methods.
Fixes: a50dad355a (net: macb: Add big endian CPU support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
JUMBO and NO_GIGABIT_HALF have the same capability masks.
Change one of them.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable SG support for Zynq SOC family devices.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the compatible string for Atmel sama5d2 SoC family as the configuration
options differ from other instances of the GEM.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Describe the handler for RXUBR better with a new comment.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Reviewied-by: Josh Cartwright <joshc@ni.com>
Reviewied-by: Ben Shelton <ben.shelton@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bitwise tests are always true here because it uses '|' where '&' is
intended.
Fixes: 98b5a0f4a2 ('net: macb: Add support for jumbo frames')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add macb_change_mtu callback; if jumbo frame support is present allow
mtu size changes upto (jumbo max length allowed - headers).
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable jumbo frame support for Zynq Ultrascale+ MPSoC.
Update the NWCFG register and descriptor length masks accordingly.
Jumbo max length register should be set according to support in SoC; it is
set to 10240 for Zynq Ultrascale+ MPSoC.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add compatible string and config structure for Zynq Ultrascale+ MPSoC
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same hardware issue the at91 must work around applies to at least the
Zynq ethernet, and possibly more devices. The driver also needs to handle
the RXUBR interrupt since it turns it on with MACB_RX_INT_FLAGS anyway.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy Rx load, observed that the Hw is updating the USED bit
and it is not updating the received frame status to the BD control
field. This could be lack of resources for processing the BDs at high
data rates. Driver drops the frame associated with this BD but not
clearing the USED bit. So, this is causing hang condition as Hw
expects USED bit to be cleared for this BD.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 02c958dd3 (net/macb: add TX multiqueue support for gem), the
initialization of tx_head and tx_tail in macb_init_rings() was moved
inside the loop that iterates over each element in the ring. Since
tx_head and tx_tail only need to be assigned once, move them back out of
the loop.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics are grouped by TX and RX errors.
The SQE Test Errors Register indicates problems with TX.
Signed-off-by: Wolfgang Steinwender <wsteinwender@pcs.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we need to check peripheral version from the hardware during probe, I
introduce a little helper to unify these tests. It would prevent to
de-synchronize the test like previously observed.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently need two checks of the peripheral version in MACB_MID register.
One of them got out of sync after modification by 8a013a9c71 (net: macb:
Include multi queue support for xilinx ZynqMP ethernet version).
Fix this in macb_configure_caps() so that xilinx ZynqMP will be considered
as a GEM flavor.
Fixes: 8a013a9c71 ("net: macb: Include multi queue support for xilinx ZynqMP
ethernet version")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Cc: <stable@vger.kernel.org> #4.0 (if it doesn't make it for -final)
Signed-off-by: David S. Miller <davem@davemloft.net>
User i/o register EMAC_USRIO or GMAC_UR can be found on both macb and gem
flavors of the peripheral. By using the proper accessor, we can add it to the
register dump feature of ethtool.
Increment the version of this API so it can be noticed from user space.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As accessing the peripheral registers need the clocks to be set, we have to
enable them as soon as possible. Their configuration depend on the type of
device used and determined by the DT compatible string. That lead to add
another initialization function in the DT configuration structure.
As the device private structure length depend on an information read in the
registers, we have to store the clock pointers in temporary variables before
feeding the structure fields.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a non-native English speaker, I would correct "capacities" of the macb
peripheral to "capabilities": correct me if I'm wrong!
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Capabilities configuration by macb_configure_caps() was moved far too late by
421d9df062 (net/macb: merge at91_ether driver into macb driver) which would
lead to badly configured hardware.
So, move this function to early probe and modify its prototype to re-gain its
original behavior.
DT data retrieval is also moved to simplify the probe code flow.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we access the MID register directly, we need to tell why
we don't use the macb_is_gem() dedicated function.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When merging at91_ether and macb driver during 421d9df062 (net/macb: merge
at91_ether driver into macb driver) the probe function has been split. The code
dealing with initialization of queues is now moved in macb_init() which needs
information computed in the parent macb_probe() function.
So, add the queue_mask information to the private structure and use it when
needed in macb_init().
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY state machine (in drivers/net/phy/phy.c) will unconditionally
call phydev->adjust_link (macb_handle_link_change) when polling in the
PHY_CHANGELINK state. As currently written, macb always ends up
requesting a new tx_clk frequency in macb_handle_link_change. It is a
waste of time to request a new tx_clk frequency if the link state hasn't
changed, as the tx_clk will already be configured properly.
Let's only request a new tx_clk clock frequency when necessary.
Signed-off-by: Jaeden Amero <jaeden.amero@ni.com>
Cc: Josh Cartwright <joshc@ni.com>
Cc: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code removed by commit 421d9df062 ("net/macb: merge
at91_ether driver into macb driver") should be removed
in the merge resolution as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurations are not modified by the driver. Make them 'const' so
that they may be placed in a read-only section.
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb and at91_ether drivers can be compiled as modules, but the at91_ether
driver use some functions and variables defined in the macb one, thus
creating a dependency on the macb driver.
Since these drivers are sharing the same logic we can easily merge
at91_ether into macb.
In order to factorize common probing logic we've added an ->init() function
to struct macb_config (the structure associated with the compatible
string), and moved macb specific init code from macb_probe to macb_init.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the functions from the Common Clk Framework handle NULL pointer as
input argument.
Since the TX clock is optional, we now set tx_clk to NULL value
instead of ERR_PTR(-ENOENT) when this clock is not available. This simplifies
the clock management and avoid the need to test tx_clk value.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With multi platform support those sections could lead to unexpected
behavior if both ARCH_AT91 and another ARM SoC using the MACB IP are
selected.
Add two new capabilities to encode the default MII mode and the presence
of a CLKEN bit in USRIO register.
Then define the appropriate config for IPs embedded in at91 SoCs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ZynqMP soc has single interrupt for all the queue events. So,
passing the IRQF_SHARED flag for interrupt registration call.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include multi queue support for the ethernet IP version in xilinx ZynqMP
SoC.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest spec "I-IPA01-0266-USR Rev 10" limit the MID field length to 12 bit
value. For previous versions it is 16 bit value.
This change will not break the backward compatibility as the latest ID value is
7 and with in the 12 bit value limit.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove Kconfig dependency and enable driver for
all ARCHs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add *_SIZE macros for the bits ENDIA_DESC and
ENDIA_PKT
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Program management descriptor's access mode according to the
dynamically detected CPU endianness.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts all __raw_readl and __raw_writel function calls
to their corresponding readl_relaxed and writel_relaxed variants.
It also tells the driver to set ahb_endian_swp_mgmt_en bit in dma_cfg
when the CPU is configured in big endian mode.
Signed-off-by: Arun Chandran <achandran@mvista.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch fixes following sparse warning:
macb.c:2038:26: warning: symbol 'gem_ethtool_ops' was not declared. Should it be static?
Alongside drops exporting of gem_ethtool_ops as there is no need.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix compilation warning:
drivers/net/ethernet/cadence/macb.c:2415:12: warning: 'macb_suspend'
defined but not used [-Wunused-function]
static int macb_suspend(struct device *dev)
drivers/net/ethernet/cadence/macb.c:2432:12: warning: 'macb_resume'
defined but not used [-Wunused-function]
static int macb_resume(struct device *dev)
when CONFIG_PM=y, CONFIG_PM_SLEEP=n are used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver is trying to acquire clocks which maybe
are not available yet. Allow the driver to request
deffered probe by providing a probe function and
registering it with module_platform_driver. [1]
This patch is based on 3.19-rc5.
[1] https://lkml.org/lkml/2013/9/23/118
Signed-off-by: Nicolae Rosia <nicolae.rosia@certsign.ro>
Signed-off-by: David S. Miller <davem@davemloft.net>
10/100 MACB does not have the same statistics possibilities as GEM. Separate
macb_ethtool_ops to make a new GEM-specific struct with the new statistics
functions included.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spaces should surround add, multiply, and bitshift operators.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change comments to not exceed 80 characters per line.
Update block comments in macb.h to start on the line after /*.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently `ethtool -S` simply returns "no stats available". It
would be more useful to see what the various ethtool statistics
registers' values are. This change implements get_ethtool_stats,
get_strings, and get_sset_count functions to accomplish this.
Read all GEM statistics registers and sum them into
macb.ethtool_stats. Add the necessary infrastructure to make this
accessible via `ethtool -S`.
Update gem_update_stats to utilize ethtool_stats.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is to help improve at-a-glace knowledge of the purpose of the
various Cadence MACB/GEM registers. Comments are more helpful for human
readability than short acronyms.
Describe various #define varibles Cadence MACB/GEM registers as documented
in Xilinix's "Zynq-7000 All Programmable SoC TechnicalReference Manual, v1.9.1
(UG-585)"
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clock is enabled without being prepared, this leads to:
WARNING: CPU: 0 PID: 1 at drivers/clk/clk.c:889 __clk_enable+0x24/0xa8()
and a non working ethernet interface.
Use clk_prepare_enable() and clk_disable_unprepare() to handle the clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inside macb_probe(), when devm_request_irq() fails on queue q, there is no need
to call devm_free_irq() on queues 0..q-1 because the managed device resources
are released later when calling free_netdev().
Also removing devm_free_irq() call from macb_remove() for the same reason.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix a bug introduced by the multiqueue support patch:
"net/macb: add TX multiqueue support for gem"
the "bp" pointer to the netdev private data was dereferenced and used after the
associated memory had been freed by calling free_netdev().
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
gem devices designed with multiqueue CANNOT work without this patch.
When probing a gem device, the driver must first prepare and enable the
peripheral clock before accessing I/O registers. The second step is to read the
MID register to find whether the device is a gem or an old macb IP.
For gem devices, it reads the Design Configuration Register 6 (DCFG6) to
compute to total number of queues, whereas macb devices always have a single
queue.
Only then it can call alloc_etherdev_mq() with the correct number of queues.
This is the reason why the order of some initializations has been changed in
macb_probe().
Eventually, the dedicated IRQ and TX ring buffer descriptors are initialized
for each queue.
For backward compatibility reasons, queue0 uses the legacy registers ISR, IER,
IDR, IMR, TBQP and RBQP. On the other hand, the other queues use new registers
ISR[1..7], IER[1..7], IDR[1..7], IMR[1..7], TBQP[1..7] and RBQP[1..7].
Except this hardware detail there is no real difference between queue0 and the
others. The driver hides that thanks to the struct macb_queue.
This structure allows us to share a common set of functions for all the queues.
Besides when a TX error occurs, the gem MUST be halted before writing any of
the TBQP registers to reset the relevant queue. An immediate side effect is
that the other queues too aren't processed anymore by the gem.
So macb_tx_error_task() calls netif_tx_stop_all_queues() to notify the Linux
network engine that all transmissions are stopped.
Also macb_tx_error_task() now calls spin_lock_irqsave() to prevent the
interrupt handlers of the other queues from running as each of them may wake
its associated queue up (please refer to macb_tx_interrupt()).
Finally, as all queues have previously been stopped, they should be restarted
calling netif_tx_start_all_queues() and setting the TSTART bit into the Network
Control Register. Before this patch, when dealing with a single queue, the
driver used to defer the reset of the faulting queue and the write of the
TSTART bit until the next call of macb_start_xmit().
As explained before, this bit is now set by macb_tx_error_task() too. That's
why the faulting queue MUST be reset by setting the TX_USED bit in its first
buffer descriptor before writing the TSTART bit.
Queue 0 always exits and is the lowest priority when other queues are available.
The higher the index of the queue is, the higher its priority is.
When transmitting frames, the TX queue is selected by the skb->queue_mapping
value. So queue discipline can be used to define the queue priority policy.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
The Kconfig file says that Gigabit mode is not supported, but it has been
supported since commit 140b7552fd ("net/macb:
Add support for Gigabit Ethernet mode").
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The precise selection is useless, so we simply remove these dependencies.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
There is no need to call ether_setup after alloc_ethdev since it was
already called there.
Follow commits c706471b26 ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbfb3 ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 8ef29f8aae.
The driver core already calls pinctrl_get() and claims the default
state. There is no need to replicate this in the driver.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the IP revision when probing.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RX checksum offload is enabled at GEM level (bit 24 set in the Network
Control Register), frames with invalid IP, TCP or UDP checksums are
discarted even if promiscuous mode is enabled (bit 4 set in the Network Control
Register).
This was verified with a simple userspace program, which corrupts UDP checksum
using libnetfilter_queue.
Then both IFF_PROMISC bit must be clear in dev->flags and NETIF_F_RXCSUM bit
must be set in dev->features to enable RX checksum offload at GEM level. This
way tcpdump is still able to capture corrupted frames.
Also skb->ip_summed is set to CHECKSUM_UNNECESSARY only when both TCP/IP or
UDP/IP checksums were verified by the GEM. Indeed the GEM may verify only IP
checksum but not the one for ICMP (or other protocol than TCP or UDP).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scatter-gather feature will allow to enable the Generic Segmentation Offload.
Generic Segmentation Offload can be enabled/disabled using ethtool -K DEVNAME gso on|off.
e.g:
ethtool -K eth0 gso off
When enabled, the driver may be provided with socket buffers splitted into many fragments.
These fragments need to be queued into the TX ring in reverse order, starting from to the
last one down to the first one, to avoid a race condition with the MAC.
Especially the 'TX_USED' bit in word 1 of the transmit buffer descriptor of the
first fragment should be cleared at the very final step of the queueing algorithm.
This will tell the hardware that fragments are ready to be sent.
Also since the MAC only update the status word of the first buffer descriptor of the
ethernet frame, the queueing algorithm can no longer expect a 'TX_USED' bit to be set by
the MAC into the buffer descriptor following the one for last fragment of the skb.
This is why the driver sets the 'TX_USED' bit before queueing any fragment, so the end of
queue position is well defined for the MAC.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This addition will also allow to configure DMA burst length.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under "heavy" RX load, the driver cannot handle the descriptors fast
enough. In detail, when a descriptor is consumed, its used flag is
cleared and once the RX budget is consumed all descriptors with a
cleared used flag are prepared to receive more data. Under load though,
the HW may constantly receive more data and use those descriptors with a
cleared used flag before they are actually prepared for next usage.
The head and tail pointers into the RX-ring should always be valid and
we can omit clearing and checking of the used flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coverage data suggests that the unlikely case of receiving data while
the receive handler is running may not be that unlikely.
Coverage data after running iperf for a while:
91320: 891: work_done = bp->macbgem_ops.mog_rx(bp, budget);
91320: 892: if (work_done < budget) {
2362: 893: napi_complete(napi);
-: 894:
-: 895: /* Packets received while interrupts were disabled */
4724: 896: status = macb_readl(bp, RSR);
2362: 897: if (unlikely(status)) {
762: 898: if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
762: 899: macb_writel(bp, ISR, MACB_BIT(RCOMP));
-: 900: napi_reschedule(napi);
-: 901: } else {
1600: 902: macb_writel(bp, IER, MACB_RX_INT_FLAGS);
-: 903: }
-: 904: }
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When data is received during the driver processing received data the
NAPI is re-scheduled. In that case the RX interrupt should not be
re-enabled.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few interrupt flags were not cleared in the ISR, resulting in a sytem
trapped in the ISR in cases one of those interrupts occurred. Clear all
flags to avoid such situations.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just as commit "net: macb: DMA-unmap full rx-buffer"
(48330e08fa), pass the size that
was used for mapping the memory also to the unmap routine to
avoid warnings from the DMA_API.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I was told that the Cadence macb driver is also useful on Microblaze.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cadence ethernet chipsets are only used on specific ARM
architectures. Add Kconfig dependencies so that drivers for these
chipsets are only buildable on the relevant architectures.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The at91_ether driver calls macb_mii_init passing a 'struct macb'
structure whose tx_clk member is initialized to 0. However,
macb_handle_link_change() expects tx_clk to be the result of
a call to clk_get, and so IS_ERR(tx_clk) to be true if the clock
is invalid. This causes an oops when booting Linux 3.14 on the
csb637 board. The following changes avoids this.
Signed-off-by: Gilles Chanteperdrix <gilles.chanteperdrix@xenomai.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace kfree_skb with dev_kfree_skb_any in macb_start_xmit that can
be called in hard irq and other contexts.
macb_start_xmit only frees skbs when dropping them so
dev_kfree_skb_any is used.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
When allocating RX buffers a fixed size is used, while freeing is based
on actually received bytes, resulting in the following kernel warning
when CONFIG_DMA_API_DEBUG is enabled:
WARNING: CPU: 0 PID: 0 at lib/dma-debug.c:1051 check_unmap+0x258/0x894()
macb e000b000.ethernet: DMA-API: device driver frees DMA memory with different size [device address=0x000000002d170040] [map size=1536 bytes] [unmap size=60 bytes]
Modules linked in:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.14.0-rc3-xilinx-00220-g49f84081ce4f #65
[<c001516c>] (unwind_backtrace) from [<c0011df8>] (show_stack+0x10/0x14)
[<c0011df8>] (show_stack) from [<c03c775c>] (dump_stack+0x7c/0xc8)
[<c03c775c>] (dump_stack) from [<c00245cc>] (warn_slowpath_common+0x60/0x84)
[<c00245cc>] (warn_slowpath_common) from [<c0024670>] (warn_slowpath_fmt+0x2c/0x3c)
[<c0024670>] (warn_slowpath_fmt) from [<c0227d44>] (check_unmap+0x258/0x894)
[<c0227d44>] (check_unmap) from [<c0228588>] (debug_dma_unmap_page+0x64/0x70)
[<c0228588>] (debug_dma_unmap_page) from [<c02ab78c>] (gem_rx+0x118/0x170)
[<c02ab78c>] (gem_rx) from [<c02ac4d4>] (macb_poll+0x24/0x94)
[<c02ac4d4>] (macb_poll) from [<c031222c>] (net_rx_action+0x6c/0x188)
[<c031222c>] (net_rx_action) from [<c0028a28>] (__do_softirq+0x108/0x280)
[<c0028a28>] (__do_softirq) from [<c0028e8c>] (irq_exit+0x84/0xf8)
[<c0028e8c>] (irq_exit) from [<c000f360>] (handle_IRQ+0x68/0x8c)
[<c000f360>] (handle_IRQ) from [<c0008528>] (gic_handle_irq+0x3c/0x60)
[<c0008528>] (gic_handle_irq) from [<c0012904>] (__irq_svc+0x44/0x78)
Exception stack(0xc056df20 to 0xc056df68)
df20: 00000001 c0577430 00000000 c0577430 04ce8e0d 00000002 edfce238 00000000
df40: 04e20f78 00000002 c05981f4 00000000 00000008 c056df68 c0064008 c02d7658
df60: 20000013 ffffffff
[<c0012904>] (__irq_svc) from [<c02d7658>] (cpuidle_enter_state+0x54/0xf8)
[<c02d7658>] (cpuidle_enter_state) from [<c02d77dc>] (cpuidle_idle_call+0xe0/0x138)
[<c02d77dc>] (cpuidle_idle_call) from [<c000f660>] (arch_cpu_idle+0x8/0x3c)
[<c000f660>] (arch_cpu_idle) from [<c006bec4>] (cpu_startup_entry+0xbc/0x124)
[<c006bec4>] (cpu_startup_entry) from [<c053daec>] (start_kernel+0x350/0x3b0)
---[ end trace d5fdc38641bd3a11 ]---
Mapped at:
[<c0227184>] debug_dma_map_page+0x48/0x11c
[<c02ab32c>] gem_rx_refill+0x154/0x1f8
[<c02ac7b4>] macb_open+0x270/0x3e0
[<c03152e0>] __dev_open+0x7c/0xfc
[<c031554c>] __dev_change_flags+0x8c/0x140
Fixing this by passing the same size which is passed during mapping the
memory to the unmap function as well.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When adjusting the link speed, the target frequency is determined by a
'swith (LINK_SPEED)' statement, that assigns the target rate only for
valid and expected LINK_SPEED values. This incomplete switch statement
leads to the following build warning:
drivers/net/ethernet/cadence/macb.c: In function 'macb_handle_link_change':
>> drivers/net/ethernet/cadence/macb.c:241:14: warning: 'rate' may be used uninitialized in this function [-Wmaybe-uninitialized]
netdev_warn(dev, "unable to generate target frequency: %ld Hz\n",
^
drivers/net/ethernet/cadence/macb.c:215:13: note: 'rate' was declared here
long ferr, rate, rate_rounded;
Fixing this by bailing out of that function in the switch's default case
before the rate variable is used.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust the ethernet clock according to the negotiated link speed.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the device managed interface to request the IRQ, simplifying error
paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the device managed version of ioremap to remap IO memory,
simplifying error paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate to using the device managed interface for clocks and clean up
the associated error paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate the suspend/resume functions to use the dev_pm_ops PM interface.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace misleading -1 (-EPERM) by a more appropriate return code (-ENXIO)
in macb_mii_probe function.
Save macb_mii_probe return before branching to err_out_unregister to avoid
erronous 0 return.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver only handle PHY description through platform_data
(macb_platform_data).
Thus, when using dt you cannot define phy properties like phy address or
phy irq pin.
This patch makes use of the of_mdiobus_register to add support for
phy device definition using dt.
A fallback to the autoscan procedure is added in case there is no phy
devices defined in dt.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit ab78029 (drivers/pinctrl: grab default handles from device core),
we can rely on device core for setting the default pins. Compile tested only.
Acked-by: Linus Walleij <linus.walleij@linaro.org> (personally at LCE13)
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jongsung Kim <neidhard.kim@lge.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This has no dependency on any of the drivers under NET_CORE.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM is able to adapt its DMA buffer size, so change
the RX path to take advantage of this possibility and
remove all kind of memcpy in this path.
This modification introduces function pointers for managing
differences between MACB and GEM adapter type.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Macb Ethernet controller requires a RX buffer of 128 bytes. It is
highly sub-optimal for Gigabit-capable GEM that is able to use
a bigger DMA buffer. Change this constant and associated macros
with data stored in the private structure.
RX DMA buffer size has to be multiple of 64 bytes as indicated in
DMA Configuration Register specification.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 749a2b6 (net/macb: clear tx/rx completion flags in ISR)
introduces clear-on-write on ISR register. This behavior is not always
implemented when using Cadence MACB/GEM and is breaking other platforms.
We are using the Design Configuration Register 1 information and a capability
property to actually activate this clear-on-write behavior on ISR.
Reported-by: Hein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Hein Tibosch <hein_tibosch@yahoo.es>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `macb_free_consistent':
drivers/net/ethernet/cadence/macb.c:878: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:883: undefined reference to `dma_free_coherent'
drivers/net/ethernet/cadence/macb.c:888: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `macb_alloc_consistent':
drivers/net/ethernet/cadence/macb.c:905: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `macb_tx_interrupt':
drivers/net/ethernet/cadence/macb.c:515: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_tx_error_task':
drivers/net/ethernet/cadence/macb.c:457: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `macb_start_xmit':
drivers/net/ethernet/cadence/macb.c:838: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `at91ether_start':
drivers/net/ethernet/cadence/at91_ether.c:49: undefined reference to `dma_alloc_coherent'
drivers/net/ethernet/cadence/at91_ether.c:60: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `at91ether_interrupt':
drivers/net/ethernet/cadence/at91_ether.c:250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `at91ether_start_xmit':
drivers/net/ethernet/cadence/at91_ether.c:169: undefined reference to `dma_map_single'
drivers/built-in.o: In function `at91ether_close':
drivers/net/ethernet/cadence/at91_ether.c:145: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Original-idea-by: <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
With of_get_mac_address() and of_get_phy_mode() now defined as dummy
functions if OF_NET is not configured, it is no longer necessary to
provide OF dependent functions as front-end. Also, the two functions
depend on OF_NET, not on OF, so the conditional code was not correct
anyway.
Drop the front-end functions and call of_get_mac_address() and
of_get_phy_mode() directly instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
With of_get_mac_address() and of_get_phy_mode() now defined as dummy
functions if OF_NET is not configured, it is no longer necessary to
provide OF dependent functions as front-end. Also, the two functions
depend on OF_NET, not on OF, so the conditional code was not correct
anyway.
Drop the front-end functions and call of_get_mac_address() and
of_get_phy_mode() directly instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use clk_prepare_enable/clk_disable_unprepare to be safe on SMP systems.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The core has a bit for swapping packet data endianism.
Reset default from Cadence is off. Xilinx however, who uses this core on the
Zynq SoCs, opted for on.
Force it to off. This shouldn't change the behaviour for current users of the
macb, but enables usage on Zynq devices.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least in the cadence IP core on the Xilinx Zynq SoC the TCOMP/RCOMP flags
are not auto-cleaned. As these flags are evaluated, they need to be cleaned.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Emitting netdev_alloc_skb and netdev_alloc_skb_ip_align OOM
messages is unnecessary as there is already a dump_stack
after allocation failures.
Other trivial changes around these removals:
Convert a few comparisons of pointer to 0 to !pointer.
Change flow to remove unnecessary label.
Remove now unused variable.
Hoist assignment from if.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull s390 update from Martin Schwidefsky:
"The most prominent change in this patch set is the software dirty bit
patch for s390. It removes __HAVE_ARCH_PAGE_TEST_AND_CLEAR_DIRTY and
the page_test_and_clear_dirty primitive which makes the common memory
management code a bit less obscure.
Heiko fixed most of the PCI related fallout, more often than not
missing GENERIC_HARDIRQS dependencies. Notable is one of the 3270
patches which adds an export to tty_io to be able to resize a tty.
The rest is the usual bunch of cleanups and bug fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/module: Add missing R_390_NONE relocation type
drivers/gpio: add missing GENERIC_HARDIRQ dependency
drivers/input: add couple of missing GENERIC_HARDIRQS dependencies
s390/cleanup: rename SPP to LPP
s390/mm: implement software dirty bits
s390/mm: Fix crst upgrade of mmap with MAP_FIXED
s390/linker skript: discard exit.data at runtime
drivers/media: add missing GENERIC_HARDIRQS dependency
s390/bpf,jit: add vlan tag support
drivers/net,AT91RM9200: add missing GENERIC_HARDIRQS dependency
iucv: fix kernel panic at reboot
s390/Kconfig: sort list of arch selected config options
phylib: remove !S390 dependeny from Kconfig
uio: remove !S390 dependency from Kconfig
dasd: fix sysfs cleanup in dasd_generic_remove
s390/pci: fix hotplug module init
s390/pci: cleanup clp page allocation
s390/pci: cleanup clp inline assembly
s390/perf: cpum_cf: fallback to software sampling events
s390/mm: provide PAGE_SHARED define
...
Pull in 'net' to take in the bug fixes that didn't make it into
3.8-final.
Also, deal with the semantic conflict of the change made to
net/ipv6/xfrm6_policy.c A missing rt6->n neighbour release
was added to 'net', but in 'net-next' we no longer cache the
neighbour entries in the ipv6 routes so that change is not
appropriate there.
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT91RM9200 driver call devm_request_irq() and therefore should
depend on GENERIC_HARDIRQS to prevent link/compile errors on plaforms
without GENERIC_HARDIRQS.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When interrupts are disabled, an RX condition can occur but
it is not reported when enabling interrupts again. We need to check
RSR and use napi_reschedule() if condition is met.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add information to the DMA Configuration Register to
maximize system performance:
- rx/tx packet buffer full memory size
- allow possibility to use INCR16 if supported
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Joachim Eastwood <manabian@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
If ndo_validate_addr is set to the generic eth_validate_addr
function there is no point in calling is_valid_ether_addr
from driver ndo_open if ndo_open is not used elsewhere in
the driver.
With this change is_valid_ether_addr will be called from the
generic eth_validate_addr function. So there should be no change
in the actual behavior.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move to circular buffers management macro and correct an error
with circular buffer initial condition.
Without this patch, the macb_tx_ring_avail() function was
not reporting the proper ring availability at startup:
macb macb: eth0: BUG! Tx Ring full when queue awake!
macb macb: eth0: tx_head = 0, tx_tail = 0
And hanginig forever...
I remove the macb_tx_ring_avail() function and use the
proven macros from circ_buf.h. CIRC_CNT() is used in the
"consumer" part of the driver: macb_tx_interrupt() to match
advice from Documentation/circular-buffers.txt.
Reported-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only the first register set is used for matching but
we support getting the initial hw addr from any of
the registers.
To prevent stale entries and false matches clear unused
register sets. This most important for the at91_ether
driver where u-boot always uses the 2nd register set.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all printk's to netdev_ counterparts and fix up some
printed texts.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer used after gpio phy interrupt support was
removed from at91_ether.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
