This patch fix following checkpatch warnings in xadc driver
1. prefer 'unsigned int' to bare use of 'unsigned'.
2. else is not generally useful after a break or return.
3. fill all function definition arguments with identifier name
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver currently registers a pair of irq handlers using
request_threaded_irq(), however the synchronization mechanism between the
hardirq and the threadedirq handler is a regular spinlock.
Unfortunately, this breaks PREEMPT_RT builds, where a spinlock can sleep,
and is thus not able to be acquired from a hardirq handler. This patch gets
rid of the threaded handler and pushes all interrupt handling into the
hardirq context, and uses request_irq().
To validate that this change has no impact on RT performance, here are
cyclictest values with no processes running:
$ sudo cyclictest -S -m -p 98
policy: fifo: loadavg: 0.00 0.01 0.05 1/174 2539
T: 0 ( 1405) P:98 I:1000 C:167010520 Min: 9 Act: 12 Avg: 12 Max: 75
T: 1 ( 1862) P:98 I:1500 C:111340339 Min: 9 Act: 12 Avg: 12 Max: 73
Then, all xadc raw handles were accessed in a continuous loop via
/sys/bus/iio/devices/iio:device0:
$ sudo cyclictest -S -m -p 98
policy: fifo: loadavg: 7.84 7.70 7.63 3/182 4260
T: 0 ( 2559) P:98 I:1000 C:241557018 Min: 11 Act: 18 Avg: 21 Max: 74
T: 1 ( 2560) P:98 I:1500 C:161038006 Min: 10 Act: 21 Avg: 20 Max: 73
Signed-off-by: Xander Huff <xander.huff@ni.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Define the register addresses for MIN_VCCPINT, MIN_VCCPAUX, MIN_VCCO_DDR
correctly.
Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx.
The XADC has a DRP interface for communication. Currently two different
frontends for the DRP interface exist. One that is only available on the ZYNQ
family as a hardmacro in the SoC portion of the ZYNQ. The other one is available
on all series 7 platforms and is a softmacro with a AXI interface. This driver
supports both interfaces and internally has a small abstraction layer that hides
the specifics of these interfaces from the main driver logic.
The ADC has a couple of internal channels which are used for voltage and
temperature monitoring of the FPGA as well as one primary and up to 16 channels
auxiliary channels for measuring external voltages. The external auxiliary
channels can either be directly connected each to one physical pin on the FPGA
or they can make use of an external multiplexer which is responsible for
multiplexing the external signals onto one pair of physical pins.
The voltage and temperature monitoring channels also have an event capability
which allows to generate a interrupt when their value falls below or raises
above a set threshold.
Buffered sampling mode is supported by the driver, but only for AXI-XADC since
the ZYNQ XADC interface does not have capabilities for supporting buffer mode
(no end-of-conversion interrupt). If buffered mode is supported the driver will
register two triggers. One "xadc-samplerate" trigger which will generate samples
with the configured samplerate. And one "xadc-convst" trigger which will
generate one sample each time the CONVST (conversion start) signal is asserted.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
