This reverts commit aa136d0c82.
As I previously[1] pointed out this implementation of XDP_REDIRECT is
wrong. XDP_REDIRECT is a facility that must work between different
NIC drivers. Another NIC driver can call ndo_xdp_xmit/nicvf_xdp_xmit,
but your driver patch assumes payload data (at top of page) will
contain a queue index and a DMA addr, this is not true and worse will
likely contain garbage.
Given you have not fixed this in due time (just reached v4.16-rc1),
the only option I see is a revert.
[1] http://lkml.kernel.org/r/20171211130902.482513d3@redhat.com
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Christina Jacob <cjacob@caviumnetworks.com>
Cc: Aleksey Makarov <aleksey.makarov@cavium.com>
Fixes: aa136d0c82 ("net: thunderx: Add support for xdp redirect")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mlxsw_sp_fib_create() and mlxsw_sp_mr_table_create()
use ERR_PTR macro to propagate int err through return of a pointer,
the return value is not NULL in case of failure. So if one
of the calls fails, one of vr->fib4, vr->fib6 or vr->mr4_table
is not NULL and mlxsw_sp_vr_is_used wrongly assumes
that vr is in use which leads to crash like following one:
[ 1293.949291] BUG: unable to handle kernel NULL pointer dereference at 00000000000006c9
[ 1293.952729] IP: mlxsw_sp_mr_table_flush+0x15/0x70 [mlxsw_spectrum]
Fix this by using local variables to hold the pointers and set vr->*
only in case everything went fine.
Fixes: 76610ebbde ("mlxsw: spectrum_router: Refactor virtual router handling")
Fixes: a3d9bc506d ("mlxsw: spectrum_router: Extend virtual routers with IPv6 support")
Fixes: d42b0965b1 ("mlxsw: spectrum_router: Add multicast routes notification handling functionality")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent a kernel panic on reboot if ptp_clock is NULL by checking
the ptp pointer before using it.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Fixes: 8c56df372b ("net: add support for Cavium PTP coprocessor")
Cc: Radoslaw Biernacki <rad@semihalf.com>
Cc: Aleksey Makarov <aleksey.makarov@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The control channel calls registered callbacks when control messages
such as XDomain protocol messages are received. The control channel
handling is done in a worker running on system workqueue which means the
networking driver can't run tear down flow which includes sending
disconnect request and waiting for a reply in the same worker. Otherwise
reply is never received (as the work is already running) and the
operation times out.
To fix this run disconnect ThunderboltIP flow asynchronously once
ThunderboltIP logout message is received.
Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
When suspending to mem or disk the Thunderbolt controller typically goes
down as well tearing down the connection automatically. However, when
suspend to idle is used this does not happen so we need to make sure the
connection is properly disconnected before it can be re-established
during resume.
Fixes: e69b6c02b4 ("net: Add support for networking over Thunderbolt cable")
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if Wake-on-LAN is enabled, the SH-ETH device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commits 91c719f5ec ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") and 744dddcae8 ("clk:
renesas: mstp: Keep wakeup sources active during system suspend"), this
workaround is no longer needed. Hence remove all explicit clock
handling to keep the device active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if Wake-on-LAN is enabled, the EtherAVB device's module clock
is manually kept running during system suspend, to make sure the device
stays active.
Since commit 91c719f5ec ("soc: renesas: rcar-sysc: Keep wakeup
sources active during system suspend") , this workaround is no longer
needed. Hence remove all explicit clock handling to keep the device
active.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forcing a specific link mode, the PHY driver must clear the
existing speed and duplex bits in BMCR while preserving some other
control bits. This logic was accidentally inverted with the introduction
of phy_modify().
Fixes: fea23fb591 ("net: phy: convert read-modify-write to phy_modify()")
Signed-off-by: Ingo van Lil <inguin@gmx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 doesn't work on the MacchiatoBIN board. It is caused by broken
multicast address filter in the mvpp2 driver.
The driver loads doesn't load any multicast entries if "allmulti" is not
set. This condition should be reversed.
The condition !netdev_mc_empty(dev) is useless (because
netdev_for_each_mc_addr is nop if the list is empty).
This patch also fixes a possible overflow of the multicast list - if
mvpp2_prs_mac_da_accept fails, we set the allmulti flag and retry.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Make allocations less aggressive in x_tables, from Minchal Hocko.
2) Fix netfilter flowtable Kconfig deps, from Pablo Neira Ayuso.
3) Fix connection loss problems in rtlwifi, from Larry Finger.
4) Correct DRAM dump length for some chips in ath10k driver, from Yu
Wang.
5) Fix ABORT handling in rxrpc, from David Howells.
6) Add SPDX tags to Sun networking drivers, from Shannon Nelson.
7) Some ipv6 onlink handling fixes, from David Ahern.
8) Netem packet scheduler interval calcualtion fix from Md. Islam.
9) Don't put crypto buffers on-stack in rxrpc, from David Howells.
10) Fix handling of error non-delivery status in netlink multicast
delivery over multiple namespaces, from Nicolas Dichtel.
11) Missing xdp flush in tuntap driver, from Jason Wang.
12) Synchonize RDS protocol netns/module teardown with rds object
management, from Sowini Varadhan.
13) Add nospec annotations to mpls, from Dan Williams.
14) Fix SKB truesize handling in TIPC, from Hoang Le.
15) Interrupt masking fixes in stammc from Niklas Cassel.
16) Don't allow ptr_ring objects to be sized outside of kmalloc's
limits, from Jason Wang.
17) Don't allow SCTP chunks to be built which will have a length
exceeding the chunk header's 16-bit length field, from Alexey
Kodanev.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (82 commits)
ibmvnic: Remove skb->protocol checks in ibmvnic_xmit
bpf: fix rlimit in reuseport net selftest
sctp: verify size of a new chunk in _sctp_make_chunk()
s390/qeth: fix SETIP command handling
s390/qeth: fix underestimated count of buffer elements
ptr_ring: try vmalloc() when kmalloc() fails
ptr_ring: fail early if queue occupies more than KMALLOC_MAX_SIZE
net: stmmac: remove redundant enable of PMT irq
net: stmmac: rename GMAC_INT_DEFAULT_MASK for dwmac4
net: stmmac: discard disabled flags in interrupt status register
ibmvnic: Reset long term map ID counter
tools/libbpf: handle issues with bpf ELF objects containing .eh_frames
selftests/bpf: add selftest that use test_libbpf_open
selftests/bpf: add test program for loading BPF ELF files
tools/libbpf: improve the pr_debug statements to contain section numbers
bpf: Sync kernel ABI header with tooling header for bpf_common.h
net: phy: fix phy_start to consider PHY_IGNORE_INTERRUPT
net: thunder: change q_len's type to handle max ring size
tipc: fix skb truesize/datasize ratio control
net/sched: cls_u32: fix cls_u32 on filter replace
...
Having these checks in ibmvnic_xmit causes problems with VLAN
tagging and balance-alb/tlb bonding modes. The restriction they
imposed can be removed.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dwmac4, GMAC_INT_DEFAULT_ENABLE already includes
GMAC_INT_PMT_EN, so it is redundant to check if hw->pmt
is set, and if so, setting the bit again.
For dwmac1000, GMAC_INT_DEFAULT_MASK does not include
GMAC_INT_DISABLE_PMT, so it is redundant to check if
hw->pmt is set, and if so, clearing an already cleared bit.
Improve code readability by removing this redundant code.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC_INT_DEFAULT_MASK is written to the interrupt enable register.
In previous versions of the IP (e.g. dwmac1000), this register was
instead an interrupt mask register.
To improve clarity and reflect reality, rename GMAC_INT_DEFAULT_MASK
to GMAC_INT_DEFAULT_ENABLE.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt status register in both dwmac1000 and dwmac4 ignores
interrupt enable (for dwmac4) / interrupt mask (for dwmac1000).
Therefore, if we want to check only the bits that can actually trigger
an irq, we have to filter the interrupt status register manually.
Commit 0a764db103 ("stmmac: Discard masked flags in interrupt status
register") fixed this for dwmac1000. Fix the same issue for dwmac4.
Just like commit 0a764db103 ("stmmac: Discard masked flags in
interrupt status register"), this makes sure that we do not get
spurious link up/link down prints.
Signed-off-by: Niklas Cassel <niklas.cassel@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating RX or TX buffer pools, the driver needs to provide a
unique mapping ID to firmware for each pool. This value is assigned
using a counter which is incremented after a new pool is created. The
ID can be an integer ranging from 1-255. When migrating to a device
that requests a different number of queues, this value was not being
reset properly. As a result, after enough migrations, the counter
exceeded the upper bound and pool creation failed. This is fixed by
resetting the counter to one in this case.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf 2018-02-09
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) Two fixes for BPF sockmap in order to break up circular map references
from programs attached to sockmap, and detaching related sockets in
case of socket close() event. For the latter we get rid of the
smap_state_change() and plug into ULP infrastructure, which will later
also be used for additional features anyway such as TX hooks. For the
second issue, dependency chain is broken up via map release callback
to free parse/verdict programs, all from John.
2) Fix a libbpf relocation issue that was found while implementing XDP
support for Suricata project. Issue was that when clang was invoked
with default target instead of bpf target, then various other e.g.
debugging relevant sections are added to the ELF file that contained
relocation entries pointing to non-BPF related sections which libbpf
trips over instead of skipping them. Test cases for libbpf are added
as well, from Jesper.
3) Various misc fixes for bpftool and one for libbpf: a small addition
to libbpf to make sure it recognizes all standard section prefixes.
Then, the Makefile in bpftool/Documentation is improved to explicitly
check for rst2man being installed on the system as we otherwise risk
installing empty man pages; the man page for bpftool-map is corrected
and a set of missing bash completions added in order to avoid shipping
bpftool where the completions are only partially working, from Quentin.
4) Fix applying the relocation to immediate load instructions in the
nfp JIT which were missing a shift, from Jakub.
5) Two fixes for the BPF kernel selftests: handle CONFIG_BPF_JIT_ALWAYS_ON=y
gracefully in test_bpf.ko module and mark them as FLAG_EXPECTED_FAIL
in this case; and explicitly delete the veth devices in the two tests
test_xdp_{meta,redirect}.sh before dismantling the netnses as when
selftests are run in batch mode, then workqueue to handle destruction
might not have finished yet and thus veth creation in next test under
same dev name would fail, from Yonghong.
6) Fix test_kmod.sh to check the test_bpf.ko module path before performing
an insmod, and fallback to modprobe. Especially the latter is useful
when having a device under test that has the modules installed instead,
from Naresh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJafa95AAoJELDendYovxMvz8oH+QGgM0ZN0YfJa2JuR/RAlYyn
3OfSlMbGOjlmT74C1Rcx+SHNbbxUunoAx70UnvLbgtzbYyX08yVNsfNFesrarAkr
dkBBsAdLLzZYOoKnSKHWGl8Cf26F5eJbLo1FSSNYzmCaz0oD+geOqIWnOQMHkuUW
Rv6En9SjgzrE6dvzQ/LNtpjqFnSwJ+cD8ZkI21YXyDmZ3/xvZ9h8ID5vrzlP4wVH
gENxAMxn9w0nlbtHLvc2KGbVOUTSsA1LxbjDqzBEIGqgKmZVdt6d1J0KfO3eM6ej
9JuPcRt34HFPifuwI6xgtcKJjEr7QptIiDiSVvifXMvQnqfGc2b+qOFLhY6XwOU=
=+zOt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"Only five small fixes for issues when running under Xen"
* tag 'for-linus-4.16-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix {set,clear}_foreign_p2m_mapping on autotranslating guests
pvcalls-back: do not return error on inet_accept EAGAIN
xen-netfront: Fix race between device setup and open
xen/grant-table: Use put_page instead of free_page
x86/xen: init %gs very early to avoid page faults with stack protector
This condition wasn't adjusted when PHY_IGNORE_INTERRUPT (-2) was added
long ago. In case of PHY_IGNORE_INTERRUPT the MAC interrupt indicates
also PHY state changes and we should do what the symbol says.
Fixes: 84a527a41f ("net: phylib: fix interrupts re-enablement in phy_start")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Cavium thunder nicvf driver supports rx/tx rings of up to 65536 entries per.
The number of entires are stored in the q_len member of struct q_desc_mem. The
problem is that q_len being a u16, results in 65536 becoming 0.
In getting pointers to descriptors in the rings, the driver uses q_len minus 1
as a mask after incrementing the pointer, in order to go back to the beginning
and not go past the end of the ring.
With the q_len set to 0 the mask is no longer correct and the driver does go
beyond the end of the ring, causing various ills. Usually the first thing that
shows up is a "NETDEV WATCHDOG: enP2p1s0f1 (nicvf): transmit queue 7 timed out"
warning.
This patch remedies the problem by changing q_len to a u32.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The most important here is the ssb fix, it has been reported by the
users frequently and the fix just missed the final v4.15. Also
numerous other fixes, mt76 had multiple problems with aggregation and
a long standing unaligned access bug in rtlwifi is finally fixed.
Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
rtlwifi
* fix unaligned access seen on ARM architecture
mt76
* various aggregation fixes which fix connection stalls
ssb
* fix b43 and b44 on non-MIPS which broke in v4.15-rc9
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJafIqwAAoJEG4XJFUm622bY1AH/jlWytWm+1/u8BTPFje0soxI
8ISNaTDVKu2s2DjCO7liuDGoQ/YqmYBYm0rc53RB0xI6hTSzdlD59gio9vUR6mF7
VQWhJ+L8H1mD0mJOwKP+VY/z0nkNK9QwOPZIO/sdspTp9LP207zSILabZEn58PEp
KKINTJagkBHb1zIm5Zl9jyin4PsOKRzWfp8z532Mw61S3+m8CbsKrRXnCB++gNAn
71a5ScPScsW/ROnJV9clx6CEsme5irFDz9qcknfz8se9do9uj+0kgkxFWGB+gnRl
2Mz3EIVhkEaZ4IMVXlv6yhan4bfkpsbPavw/hO2iHbLfZNpXrWEM+zIoSzOmOoc=
=BJaf
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-02-08' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
The most important here is the ssb fix, it has been reported by the
users frequently and the fix just missed the final v4.15. Also
numerous other fixes, mt76 had multiple problems with aggregation and
a long standing unaligned access bug in rtlwifi is finally fixed.
Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
rtlwifi
* fix unaligned access seen on ARM architecture
mt76
* various aggregation fixes which fix connection stalls
ssb
* fix b43 and b44 on non-MIPS which broke in v4.15-rc9
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While handling a driver reset we get a H_CLOSED return trying
to send a CRQ event. When this occurs we need to queue up another
reset attempt. Without doing this we see instances where the driver
is left in a closed state because the reset failed and there is no
further attempts to reset the driver.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using devmap to redirect packets between interfaces,
xdp_do_flush() is usually a must to flush any batched
packets. Unfortunately this is missed in current tuntap
implementation.
Unlike most hardware driver which did XDP inside NAPI loop and call
xdp_do_flush() at then end of each round of poll. TAP did it in the
context of process e.g tun_get_user(). So fix this by count the
pending redirected packets and flush when it exceeds NAPI_POLL_WEIGHT
or MSG_MORE was cleared by sendmsg() caller.
With this fix, xdp_redirect_map works again between two TAPs.
Fixes: 761876c857 ("tap: XDP support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git fixes for 4.16. Major changes:
ath10k
* correct firmware RAM dump length for QCA6174/QCA9377
* add new QCA988X device id
* fix a kernel panic during pci probe
* revert a recent commit which broke ath10k firmware metadata parsing
ath9k
* fix a noise floor regression introduced during the merge window
* add new device id
DKMS and similar out-of-tree module replacement services use
module version to make sure the out-of-tree software is not
older than the module shipped with the kernel. We use the
kernel version in ethtool -i output, put it into MODULE_VERSION
as well.
Reported-by: Jan Gutter <jan.gutter@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most FWs limit the number of TSO segments a frame can produce
to 64. This is for fairness and efficiency (of FW datapath)
reasons. If a frame with larger number of segments is submitted
the FW will drop it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All netdevs which can accept TC offloads must implement
.ndo_set_features(). nfp_reprs currently do not do that, which
means hw-tc-offload can be turned on and off even when offloads
are active.
Whether the offloads are active is really a question to nfp_ports,
so remove the per-app tc_busy callback indirection thing, and
simply count the number of offloaded items in nfp_port structure.
Fixes: 8a2768732a ("nfp: provide infrastructure for offloading flower based TC filters")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_port is a structure which represents an ASIC port, both
PCIe vNIC (on a PF or a VF) or the external MAC port. vNIC
netdev (struct nfp_net) and pure representor netdev (struct
nfp_repr) both have a pointer to this structure. nfp_reprs
always have a port associated. nfp_nets, however, only represent
a device port in legacy mode, where they are considered the
MAC port. In switchdev mode they are just the CPU's side of
the PCIe link.
By definition TC offloads only apply to device ports. Don't
set the flag on vNICs without a port (i.e. in switchdev mode).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upcoming changes will require all netdevs supporting TC offloads
to have a full struct nfp_port. Require those for BPF offload.
The operation without management FW reporting information about
Ethernet ports is something we only support for very old and very
basic NIC firmwares anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Immed relocation is missing a shift which means for larger
offsets the lower and higher part of the address would be
ORed together.
Fixes: ce4ebfd859 ("nfp: bpf: add helpers for updating immediate instructions")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
It was discovered that simple program which indefinitely sends 200b UDP
packets and runs on TI AM574x SoC (SMP) under RT Kernel triggers network
watchdog timeout in TI CPSW driver (<6 hours run). The network watchdog
timeout is triggered due to race between cpsw_ndo_start_xmit() and
cpsw_tx_handler() [NAPI]
cpsw_ndo_start_xmit()
if (unlikely(!cpdma_check_free_tx_desc(txch))) {
txq = netdev_get_tx_queue(ndev, q_idx);
netif_tx_stop_queue(txq);
^^ as per [1] barier has to be used after set_bit() otherwise new value
might not be visible to other cpus
}
cpsw_tx_handler()
if (unlikely(netif_tx_queue_stopped(txq)))
netif_tx_wake_queue(txq);
and when it happens ndev TX queue became disabled forever while driver's HW
TX queue is empty.
Fix this, by adding smp_mb__after_atomic() after netif_tx_stop_queue()
calls and double check for free TX descriptors after stopping ndev TX queue
- if there are free TX descriptors wake up ndev TX queue.
[1] https://www.kernel.org/doc/html/latest/core-api/atomic_ops.html
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change will guard against a double free in the case that the
buffers were previously freed at some other time, such as during
a device reset. It resolves a kernel oops that occurred when changing
the VNIC device's MTU.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At some point, a check was added to exit the polling routine during resets.
This makes sense for most reset conditions, but for a non-fatal error, we
expect the polling routine to continue running to properly clean up the rx
queues. This patch checks if we are performing a non-fatal reset and if we
are, continues normal polling operation.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the number of queues per enabled TC and report available queues
to the kernel without having to limit them to the max RSS limit so
they are available to be mapped for XPS. This allows a queue per
processing thread available for handling traffic for the given
traffic class.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the appropriate SPDX license tags to the Sun network drivers
as outlined in Documentation/process/license-rules.rst.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit baf5086840 ("cxgb4: restructure VF mgmt code") has reordered
some code but an error handling label has not been updated accordingly.
So fix it and free 'adapter' if 't4_wait_dev_ready()' fails.
Fixes: baf5086840 ("cxgb4: restructure VF mgmt code")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 8da58553cc ("ath9k: Use calibrated noise floor value
when available") introduced regression in ath9k_hw_getchan_noise
where per chain nominal noise floor has been taken instead default
for channel.
Revert to original default channel noise floor.
Fixes: 8da58553cc ("ath9k: Use calibrated noise floor value when available")
Reported-by: Sebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some modern Ubiquiti devices contain a rebranded QCA988X rev2 with
a custom Ubiquiti vendor and device id. This patch adds support for
those devices, treating them as a QCA988X v2.
Signed-off-by: Tobias Schramm <tobleminer@gmail.com>
[kvalo@codeaurora.org: rebase, add missing fields in hw_params, fix a long line in pci.c:61]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of DRAM dump for QCA6174 hw3.0/hw3.2 and QCA9377 hw1.1
are less than the actual value, some coredump contents are missed.
To fix it, change the length from 0x90000 to 0xa8000.
Fixes: 703f261dd7 ("ath10k: add memory dump support for QCA6174/QCA9377")
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There has been a coding error in rtl8821ae since it was first introduced,
namely that an 8-bit register was read using a 16-bit read in
_rtl8821ae_dbi_read(). This error was fixed with commit 40b368af4b
("rtlwifi: Fix alignment issues"); however, this change led to
instability in the connection. To restore stability, this change
was reverted in commit b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection
lost problem").
Unfortunately, the unaligned access causes machine checks in ARM
architecture, and we were finally forced to find the actual cause of the
problem on x86 platforms. Following a suggestion from Pkshih
<pkshih@realtek.com>, it was found that increasing the ASPM L1
latency from 0 to 7 fixed the instability. This parameter was varied to
see if a smaller value would work; however, it appears that 7 is the
safest value. A new symbol is defined for this quantity, thus it can be
easily changed if necessary.
Fixes: b8b8b16352 ("rtlwifi: rtl8821ae: Fix connection lost problem")
Cc: Stable <stable@vger.kernel.org> # 4.14+
Fix-suggested-by: Pkshih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Tested-by: James Cameron <quozl@laptop.org> # x86_64 OLPC NL3
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking fixes from David Miller:
1) Fix error path in netdevsim, from Jakub Kicinski.
2) Default values listed in tcp_wmem and tcp_rmem documentation were
inaccurate, from Tonghao Zhang.
3) Fix route leaks in SCTP, both for ipv4 and ipv6. From Alexey Kodanev
and Tommi Rantala.
4) Fix "MASK < Y" meant to be "MASK << Y" in xgbe driver, from Wolfram
Sang.
5) Use after free in u32_destroy_key(), from Paolo Abeni.
6) Fix two TX issues in be2net driver, from Suredh Reddy.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (25 commits)
be2net: Handle transmit completion errors in Lancer
be2net: Fix HW stall issue in Lancer
RDS: IB: Fix null pointer issue
nfp: fix kdoc warnings on nested structures
sample/bpf: fix erspan metadata
net: erspan: fix erspan config overwrite
net: erspan: fix metadata extraction
cls_u32: fix use after free in u32_destroy_key()
net: amd-xgbe: fix comparison to bitshift when dealing with a mask
net: phy: Handle not having GPIO enabled in the kernel
ibmvnic: fix empty firmware version and errors cleanup
sctp: fix dst refcnt leak in sctp_v4_get_dst
sctp: fix dst refcnt leak in sctp_v6_get_dst()
dwc-xlgmac: remove Jie Deng as co-maintainer
doc: Change the min default value of tcp_wmem/tcp_rmem.
samples/bpf: use bpf_set_link_xdp_fd
libbpf: add missing SPDX-License-Identifier
libbpf: add error reporting in XDP
libbpf: add function to setup XDP
tools: add netlink.h and if_link.h in tools uapi
...
- Clean up some function signatures in rxe for clarity
- Tidy the RDMA netlink header to remove unimplemented constants
- bnxt_re driver fixes, one is a regression this window.
- Minor hns driver fixes
- Various fixes from Dan Carpenter and his tool
- Fix IRQ cleanup race in HFI1
- HF1 performance optimizations and a fix to report counters in the right units
- Fix for an IPoIB startup sequence race with the external manager
- Oops fix for the new kabi path
- Endian cleanups for hns
- Fix for mlx5 related to the new automatic affinity support
-----BEGIN PGP SIGNATURE-----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=xwZz
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull more rdma updates from Doug Ledford:
"Items of note:
- two patches fix a regression in the 4.15 kernel. The 4.14 kernel
worked fine with NVMe over Fabrics and mlx5 adapters. That broke in
4.15. The fix is here.
- one of the patches (the endian notation patch from Lijun) looks
like a lot of lines of change, but it's mostly mechanical in
nature. It amounts to the biggest chunk of change in it (it's about
2/3rds of the overall pull request).
Summary:
- Clean up some function signatures in rxe for clarity
- Tidy the RDMA netlink header to remove unimplemented constants
- bnxt_re driver fixes, one is a regression this window.
- Minor hns driver fixes
- Various fixes from Dan Carpenter and his tool
- Fix IRQ cleanup race in HFI1
- HF1 performance optimizations and a fix to report counters in the right units
- Fix for an IPoIB startup sequence race with the external manager
- Oops fix for the new kabi path
- Endian cleanups for hns
- Fix for mlx5 related to the new automatic affinity support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (38 commits)
net/mlx5: increase async EQ to avoid EQ overrun
mlx5: fix mlx5_get_vector_affinity to start from completion vector 0
RDMA/hns: Fix the endian problem for hns
IB/uverbs: Use the standard kConfig format for experimental
IB: Update references to libibverbs
IB/hfi1: Add 16B rcvhdr trace support
IB/hfi1: Convert kzalloc_node and kcalloc to use kcalloc_node
IB/core: Avoid a potential OOPs for an unused optional parameter
IB/core: Map iWarp AH type to undefined in rdma_ah_find_type
IB/ipoib: Fix for potential no-carrier state
IB/hfi1: Show fault stats in both TX and RX directions
IB/hfi1: Remove blind constants from 16B update
IB/hfi1: Convert PortXmitWait/PortVLXmitWait counters to flit times
IB/hfi1: Do not override given pcie_pset value
IB/hfi1: Optimize process_receive_ib()
IB/hfi1: Remove unnecessary fecn and becn fields
IB/hfi1: Look up ibport using a pointer in receive path
IB/hfi1: Optimize packet type comparison using 9B and bypass code paths
IB/hfi1: Compute BTH only for RDMA_WRITE_LAST/SEND_LAST packet
IB/hfi1: Remove dependence on qp->s_hdrwords
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttq9
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- skip AER driver error recovery callbacks for correctable errors
reported via ACPI APEI, as we already do for errors reported via the
native path (Tyler Baicar)
- fix DPC shared interrupt handling (Alex Williamson)
- print full DPC interrupt number (Keith Busch)
- enable DPC only if AER is available (Keith Busch)
- simplify DPC code (Bjorn Helgaas)
- calculate ASPM L1 substate parameter instead of hardcoding it (Bjorn
Helgaas)
- enable Latency Tolerance Reporting for ASPM L1 substates (Bjorn
Helgaas)
- move ASPM internal interfaces out of public header (Bjorn Helgaas)
- allow hot-removal of VGA devices (Mika Westerberg)
- speed up unplug and shutdown by assuming Thunderbolt controllers
don't support Command Completed events (Lukas Wunner)
- add AtomicOps support for GPU and Infiniband drivers (Felix Kuehling,
Jay Cornwall)
- expose "ari_enabled" in sysfs to help NIC naming (Stuart Hayes)
- clean up PCI DMA interface usage (Christoph Hellwig)
- remove PCI pool API (replaced with DMA pool) (Romain Perier)
- deprecate pci_get_bus_and_slot(), which assumed PCI domain 0 (Sinan
Kaya)
- move DT PCI code from drivers/of/ to drivers/pci/ (Rob Herring)
- add PCI-specific wrappers for dev_info(), etc (Frederick Lawler)
- remove warnings on sysfs mmap failure (Bjorn Helgaas)
- quiet ROM validation messages (Alex Deucher)
- remove redundant memory alloc failure messages (Markus Elfring)
- fill in types for compile-time VGA and other I/O port resources
(Bjorn Helgaas)
- make "pci=pcie_scan_all" work for Root Ports as well as Downstream
Ports to help AmigaOne X1000 (Bjorn Helgaas)
- add SPDX tags to all PCI files (Bjorn Helgaas)
- quirk Marvell 9128 DMA aliases (Alex Williamson)
- quirk broken INTx disable on Ceton InfiniTV4 (Bjorn Helgaas)
- fix CONFIG_PCI=n build by adding dummy pci_irqd_intx_xlate() (Niklas
Cassel)
- use DMA API to get MSI address for DesignWare IP (Niklas Cassel)
- fix endpoint-mode DMA mask configuration (Kishon Vijay Abraham I)
- fix ARTPEC-6 incorrect IS_ERR() usage (Wei Yongjun)
- add support for ARTPEC-7 SoC (Niklas Cassel)
- add endpoint-mode support for ARTPEC (Niklas Cassel)
- add Cadence PCIe host and endpoint controller driver (Cyrille
Pitchen)
- handle multiple INTx status bits being set in dra7xx (Vignesh R)
- translate dra7xx hwirq range to fix INTD handling (Vignesh R)
- remove deprecated Exynos PHY initialization code (Jaehoon Chung)
- fix MSI erratum workaround for HiSilicon Hip06/Hip07 (Dongdong Liu)
- fix NULL pointer dereference in iProc BCMA driver (Ray Jui)
- fix Keystone interrupt-controller-node lookup (Johan Hovold)
- constify qcom driver structures (Julia Lawall)
- rework Tegra config space mapping to increase space available for
endpoints (Vidya Sagar)
- simplify Tegra driver by using bus->sysdata (Manikanta Maddireddy)
- remove PCI_REASSIGN_ALL_BUS usage on Tegra (Manikanta Maddireddy)
- add support for Global Fabric Manager Server (GFMS) event to
Microsemi Switchtec switch driver (Logan Gunthorpe)
- add IDs for Switchtec PSX 24xG3 and PSX 48xG3 (Kelvin Cao)
* tag 'pci-v4.16-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI: cadence: Add EndPoint Controller driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe endpoint controller
PCI: endpoint: Fix EPF device name to support multi-function devices
PCI: endpoint: Add the function number as argument to EPC ops
PCI: cadence: Add host driver for Cadence PCIe controller
dt-bindings: PCI: cadence: Add DT bindings for Cadence PCIe host controller
PCI: Add vendor ID for Cadence
PCI: Add generic function to probe PCI host controllers
PCI: generic: fix missing call of pci_free_resource_list()
PCI: OF: Add generic function to parse and allocate PCI resources
PCI: Regroup all PCI related entries into drivers/pci/Makefile
PCI/DPC: Reformat DPC register definitions
PCI/DPC: Add and use DPC Status register field definitions
PCI/DPC: Squash dpc_rp_pio_get_info() into dpc_process_rp_pio_error()
PCI/DPC: Remove unnecessary RP PIO register structs
PCI/DPC: Push dpc->rp_pio_status assignment into dpc_rp_pio_get_info()
PCI/DPC: Squash dpc_rp_pio_print_error() into dpc_rp_pio_get_info()
PCI/DPC: Make RP PIO log size check more generic
PCI/DPC: Rename local "status" to "dpc_status"
PCI/DPC: Squash dpc_rp_pio_print_tlp_header() into dpc_rp_pio_print_error()
...
If the driver receives a TX CQE with status as 0x1 or 0x9 or 0xb,
the completion indexes should not be used. The driver must stop
consuming CQEs from this TXQ/CQ. The TXQ from this point on-wards
to be in a bad state. Driver should destroy and recreate the TXQ.
0x1: LANCER_TX_COMP_LSO_ERR
0x9 LANCER_TX_COMP_SGE_ERR
0xb: LANCER_TX_COMP_PARITY_ERR
Reset the adapter if driver sees this error in TX completion. Also
adding sge error counter in ethtool stats.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer HW cannot handle a TSO packet with a single segment.
Disable TSO/GSO for such packets.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 84ce5b9877 ("scripts: kernel-doc: improve nested logic to
handle multiple identifiers") improved the handling of nested structure
definitions in scripts/kernel-doc, and changed the expected format of
documentation. This causes new warnings to appear on W=1 builds.
Only comment changes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to a typo, the mask was destroyed by a comparison instead of a bit
shift.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_GPIOLIB is disabled, fwnode_get_named_gpiod() becomes a stub
function, which return -ENOSYS. Handle this in the same way as
-ENOENT, i.e. assume there is no GPIO used to reset the PHYs.
Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: bafbdd527d ("phylib: Add device reset GPIO support")
Signed-off-by: David S. Miller <davem@davemloft.net>
When a netfront device is set up it registers a netdev fairly early on,
before it has set up the queues and is actually usable. A userspace tool
like NetworkManager will immediately try to open it and access its state
as soon as it appears. The bug can be reproduced by hotplugging VIFs
until the VM runs out of grant refs. It registers the netdev but fails
to set up any queues (since there are no more grant refs). In the
meantime, NetworkManager opens the device and the kernel crashes trying
to access the queues (of which there are none).
Fix this in two ways:
* For initial setup, register the netdev much later, after the queues
are setup. This avoids the race entirely.
* During a suspend/resume cycle, the frontend reconnects to the backend
and the queues are recreated. It is possible (though highly unlikely) to
race with something opening the device and accessing the queues after
they have been destroyed but before they have been recreated. Extend the
region covered by the rtnl semaphore to protect against this race. There
is a possibility that we fail to recreate the queues so check for this
in the open function.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
This patch makes sure that the firmware version is never NULL. Moreover,
it also performs some cleanup on the error messages.
Fixes: a107311d7f ("ibmvnic: fix firmware version when no firmware level
has been provided by the VIOS server")
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Mediatek ethernet driver fails to build after commit 23c35f48f5
("pinctrl: remove include file from <linux/device.h>") because it relies
on the pinctrl/consumer.h and pinctrl/devinfo.h being pulled in by the
device.h header implicitly.
Include these headers explicitly to avoid the build failure.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently the async EQ has 256 entries only. It might not be big enough
for the SW to handle all the needed pending events. For example, in case
of many QPs (let's say 1024) connected to a SRQ created using NVMeOF target
and the target goes down, the FW will raise 1024 "last WQE reached" events
and may cause EQ overrun. Increase the EQ to more reasonable size, that beyond
it the FW should be able to delay the event and raise it later on using internal
backpressure mechanism.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Alexei Starovoitov says:
====================
pull-request: bpf 2018-02-02
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) support XDP attach in libbpf, from Eric.
2) minor fixes, from Daniel, Jakub, Yonghong, Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) The bnx2x can hang if you give it a GSO packet with a segment size
which is too big for the hardware, detect and drop in this case.
From Daniel Axtens.
2) Fix some overflows and pointer leaks in xtables, from Dmitry Vyukov.
3) Missing RCU locking in igmp, from Eric Dumazet.
4) Fix RX checksum handling on r8152, it can only checksum UDP and TCP
packets. From Hayes Wang.
5) Minor pacing tweak to TCP BBR congestion control, from Neal
Cardwell.
6) Missing RCU annotations in cls_u32, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (30 commits)
Revert "defer call to mem_cgroup_sk_alloc()"
soreuseport: fix mem leak in reuseport_add_sock()
net: qlge: use memmove instead of skb_copy_to_linear_data
net: qed: use correct strncpy() size
net: cxgb4: avoid memcpy beyond end of source buffer
cls_u32: add missing RCU annotation.
r8152: set rx mode early when linking on
r8152: fix wrong checksum status for received IPv4 packets
nfp: fix TLV offset calculation
net: pxa168_eth: add netconsole support
net: igmp: add a missing rcu locking section
ibmvnic: fix firmware version when no firmware level has been provided by the VIOS server
vmxnet3: remove redundant initialization of pointer 'rq'
lan78xx: remove redundant initialization of pointer 'phydev'
net: jme: remove unused initialization of 'rxdesc'
rtnetlink: remove check for IFLA_IF_NETNSID
rocker: fix possible null pointer dereference in rocker_router_fib_event_work
inet: Avoid unitialized variable warning in inet_unhash()
net: bridge: Fix uninitialized error in br_fdb_sync_static()
openvswitch: Remove padding from packet before L3+ conntrack processing
...
gcc-8 points out that the skb_copy_to_linear_data() argument points to
the skb itself, which makes it run into a problem with overlapping
memcpy arguments:
In file included from include/linux/ip.h:20,
from drivers/net/ethernet/qlogic/qlge/qlge_main.c:26:
drivers/net/ethernet/qlogic/qlge/qlge_main.c: In function 'ql_realign_skb':
include/linux/skbuff.h:3378:2: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
memcpy(skb->data, from, len);
It's unclear to me what the best solution is, maybe it ought to use a
different helper that adjusts the skb data in a safe way. Simply using
memmove() here seems like the easiest workaround.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
passing the strlen() of the source string as the destination
length is pointless, and gcc-8 now warns about it:
drivers/net/ethernet/qlogic/qed/qed_debug.c: In function 'qed_grc_dump':
include/linux/string.h:253: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
This changes qed_grc_dump_big_ram() to instead uses the length of
the destination buffer, and use strscpy() to guarantee nul-termination.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with link-time-optimizations revealed that the cxgb4 driver does
a fixed-size memcpy() from a variable-length constant string into the
network interface name:
In function 'memcpy',
inlined from 'cfg_queues_uld.constprop' at drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:335:2,
inlined from 'cxgb4_register_uld.constprop' at drivers/net/ethernet/chelsio/cxgb4/cxgb4_uld.c:719:9:
include/linux/string.h:350:3: error: call to '__read_overflow2' declared with attribute error: detected read beyond size of object passed as 2nd parameter
__read_overflow2();
^
I can see two equally workable solutions: either we use a strncpy() instead
of the memcpy() to stop at the end of the input, or we make the source buffer
fixed length as well. This implements the latter.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set rx mode before calling netif_wake_queue() when linking on to avoid
the device missing the receiving packets.
The transmission may start after calling netif_wake_queue(), and the
packets of resopnse may reach before calling rtl8152_set_rx_mode()
which let the device could receive packets. Then, the packets of
response would be missed.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device could only check the checksum of TCP and UDP packets. Therefore,
for the IPv4 packets excluding TCP and UDP, the check of checksum is necessary,
even though the IP checksum is correct.
Take ICMP for example, The IP checksum may be correct, but the ICMP checksum
may be wrong.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data pointer in the config space TLV parser already includes
NFP_NET_CFG_TLV_BASE, it should not be added again. Incorrect
offset values were only used in printed user output, rendering
the bug merely cosmetic.
Fixes: 73a0329b05 ("nfp: add TLV capabilities to the BAR")
Signed-off-by: Edwin Peer <edwin.peer@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements ndo_poll_controller callback which is necessary to
enable netconsole.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older versions of VIOS servers do not send the firmware level in the VPD
buffer for the ibmvnic driver. Thus, not only the current message is mis-
leading but the firmware version in the ethtool will be NULL. Therefore,
this patch fixes the firmware string and its warning.
Fixes: 4e6759be28 ("ibmvnic: Feature implementation of VPD for the ibmvnic driver")
Signed-off-by: Desnes A. Nunes do Rosario <desnesn@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer rq is being initialized but this value is never read, it
is being updated inside a for-loop. Remove the initialization and
move it into the scope of the for-loop.
Cleans up clang warning:
drivers/net/vmxnet3/vmxnet3_drv.c:2763:27: warning: Value stored
to 'rq' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer phydev is initialized and this value is never read, phydev
is immediately updated to a new value, hence this initialization
is redundant and can be removed
Cleans up clang warning:
drivers/net/usb/lan78xx.c:2009:21: warning: Value stored to 'phydev'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer rxdesc is assigned a value that is never read, it is overwritten
by a new assignment inside a while loop hence the initial assignment
is redundant and can be removed.
Cleans up clang warning:
drivers/net/ethernet/jme.c:1074:17: warning: Value stored to 'rxdesc'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Currently, rocker user may experience following null pointer
derefence bug:
[ 3.062141] BUG: unable to handle kernel NULL pointer dereference at 00000000000000d0
[ 3.065163] IP: rocker_router_fib_event_work+0x36/0x110 [rocker]
The problem is uninitialized rocker->wops pointer that is initialized
only with the first initialized port. So move the port initialization
before registering the fib events.
Fixes: 936bd48656 ("rocker: use FIB notifications instead of switchdev calls")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable head is initialized to a value that is never read and is
being updated to a new value a few lines later, hence this
initialization is redundant and can be safely removed as well
as the now unused pointer txq.
Cleans up clang warning:
drivers/net/ethernet/emulex/benet/be_main.c:996:6: warning: Value
stored to 'head' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a bnx2x card is passed a GSO packet with a gso_size larger than
~9700 bytes, it will cause a firmware error that will bring the card
down:
bnx2x: [bnx2x_attn_int_deasserted3:4323(enP24p1s0f0)]MC assert!
bnx2x: [bnx2x_mc_assert:720(enP24p1s0f0)]XSTORM_ASSERT_LIST_INDEX 0x2
bnx2x: [bnx2x_mc_assert:736(enP24p1s0f0)]XSTORM_ASSERT_INDEX 0x0 = 0x00000000 0x25e43e47 0x00463e01 0x00010052
bnx2x: [bnx2x_mc_assert:750(enP24p1s0f0)]Chip Revision: everest3, FW Version: 7_13_1
... (dump of values continues) ...
Detect when the mac length of a GSO packet is greater than the maximum
packet size (9700 bytes) and disable GSO.
Signed-off-by: Daniel Axtens <dja@axtens.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Undo loop condition on the error path would cause the i counter
to go below zero, if allocation failure happened with the first
(i.e. 0th) element of the array.
Fixes: 395cacb5f1 ("netdevsim: bpf: support fake map offload")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Avoids data connection stalls when the client toggles powersave mode
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Avoids timeouts on reordered A-MPDU rx frames
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With software A-MPDU reordering in place, frames that notify mac80211 of
powersave changes are reordered as well, which can cause connection
stalls. Fix this by implementing powersave state processing in the
driver.
Fixes: aee5b8cf24 ("mt76: implement A-MPDU rx reordering in the driver code")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pull networking updates from David Miller:
1) Significantly shrink the core networking routing structures. Result
of http://vger.kernel.org/~davem/seoul2017_netdev_keynote.pdf
2) Add netdevsim driver for testing various offloads, from Jakub
Kicinski.
3) Support cross-chip FDB operations in DSA, from Vivien Didelot.
4) Add a 2nd listener hash table for TCP, similar to what was done for
UDP. From Martin KaFai Lau.
5) Add eBPF based queue selection to tun, from Jason Wang.
6) Lockless qdisc support, from John Fastabend.
7) SCTP stream interleave support, from Xin Long.
8) Smoother TCP receive autotuning, from Eric Dumazet.
9) Lots of erspan tunneling enhancements, from William Tu.
10) Add true function call support to BPF, from Alexei Starovoitov.
11) Add explicit support for GRO HW offloading, from Michael Chan.
12) Support extack generation in more netlink subsystems. From Alexander
Aring, Quentin Monnet, and Jakub Kicinski.
13) Add 1000BaseX, flow control, and EEE support to mvneta driver. From
Russell King.
14) Add flow table abstraction to netfilter, from Pablo Neira Ayuso.
15) Many improvements and simplifications to the NFP driver bpf JIT,
from Jakub Kicinski.
16) Support for ipv6 non-equal cost multipath routing, from Ido
Schimmel.
17) Add resource abstration to devlink, from Arkadi Sharshevsky.
18) Packet scheduler classifier shared filter block support, from Jiri
Pirko.
19) Avoid locking in act_csum, from Davide Caratti.
20) devinet_ioctl() simplifications from Al viro.
21) More TCP bpf improvements from Lawrence Brakmo.
22) Add support for onlink ipv6 route flag, similar to ipv4, from David
Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1925 commits)
tls: Add support for encryption using async offload accelerator
ip6mr: fix stale iterator
net/sched: kconfig: Remove blank help texts
openvswitch: meter: Use 64-bit arithmetic instead of 32-bit
tcp_nv: fix potential integer overflow in tcpnv_acked
r8169: fix RTL8168EP take too long to complete driver initialization.
qmi_wwan: Add support for Quectel EP06
rtnetlink: enable IFLA_IF_NETNSID for RTM_NEWLINK
ipmr: Fix ptrdiff_t print formatting
ibmvnic: Wait for device response when changing MAC
qlcnic: fix deadlock bug
tcp: release sk_frag.page in tcp_disconnect
ipv4: Get the address of interface correctly.
net_sched: gen_estimator: fix lockdep splat
net: macb: Handle HRESP error
net/mlx5e: IPoIB, Fix copy-paste bug in flow steering refactoring
ipv6: addrconf: break critical section in addrconf_verify_rtnl()
ipv6: change route cache aging logic
i40e/i40evf: Update DESC_NEEDED value to reflect larger value
bnxt_en: cleanup DIM work on device shutdown
...
Pull crypto updates from Herbert Xu:
"API:
- Enforce the setting of keys for keyed aead/hash/skcipher
algorithms.
- Add multibuf speed tests in tcrypt.
Algorithms:
- Improve performance of sha3-generic.
- Add native sha512 support on arm64.
- Add v8.2 Crypto Extentions version of sha3/sm3 on arm64.
- Avoid hmac nesting by requiring underlying algorithm to be unkeyed.
- Add cryptd_max_cpu_qlen module parameter to cryptd.
Drivers:
- Add support for EIP97 engine in inside-secure.
- Add inline IPsec support to chelsio.
- Add RevB core support to crypto4xx.
- Fix AEAD ICV check in crypto4xx.
- Add stm32 crypto driver.
- Add support for BCM63xx platforms in bcm2835 and remove bcm63xx.
- Add Derived Key Protocol (DKP) support in caam.
- Add Samsung Exynos True RNG driver.
- Add support for Exynos5250+ SoCs in exynos PRNG driver"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (166 commits)
crypto: picoxcell - Fix error handling in spacc_probe()
crypto: arm64/sha512 - fix/improve new v8.2 Crypto Extensions code
crypto: arm64/sm3 - new v8.2 Crypto Extensions implementation
crypto: arm64/sha3 - new v8.2 Crypto Extensions implementation
crypto: testmgr - add new testcases for sha3
crypto: sha3-generic - export init/update/final routines
crypto: sha3-generic - simplify code
crypto: sha3-generic - rewrite KECCAK transform to help the compiler optimize
crypto: sha3-generic - fixes for alignment and big endian operation
crypto: aesni - handle zero length dst buffer
crypto: artpec6 - remove select on non-existing CRYPTO_SHA384
hwrng: bcm2835 - Remove redundant dev_err call in bcm2835_rng_probe()
crypto: stm32 - remove redundant dev_err call in stm32_cryp_probe()
crypto: axis - remove unnecessary platform_get_resource() error check
crypto: testmgr - test misuse of result in ahash
crypto: inside-secure - make function safexcel_try_push_requests static
crypto: aes-generic - fix aes-generic regression on powerpc
crypto: chelsio - Fix indentation warning
crypto: arm64/sha1-ce - get rid of literal pool
crypto: arm64/sha2-ce - move the round constant table to .rodata section
...
- Misc small driver fixups to
bnxt_re/hfi1/qib/hns/ocrdma/rdmavt/vmw_pvrdma/nes
- Several major feature adds to bnxt_re driver: SRIOV VF RoCE support,
HugePages support, extended hardware stats support, and SRQ support
- A notable number of fixes to the i40iw driver from debugging scale up
testing
- More work to enable the new hip08 chip in the hns driver
- Misc small ULP fixups to srp/srpt//ipoib
- Preparation for srp initiator and target to support the RDMA-CM
protocol for connections
- Add RDMA-CM support to srp initiator, srp target is still a WIP
- Fixes for a couple of places where ipoib could spam the dmesg log
- Fix encode/decode of FDR/EDR data rates in the core
- Many patches from Parav with ongoing work to clean up inconsistencies
and bugs in RoCE support around the rdma_cm
- mlx5 driver support for the userspace features 'thread domain', 'wallclock
timestamps' and 'DV Direct Connected transport'. Support for the firmware
dual port rocee capability
- Core support for more than 32 rdma devices in the char dev allocation
- kernel doc updates from Randy Dunlap
- New netlink uAPI for inspecting RDMA objects similar in spirit to 'ss'
- One minor change to the kobject code acked by GKH
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=sMXV
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull RDMA subsystem updates from Jason Gunthorpe:
"Overall this cycle did not have any major excitement, and did not
require any shared branch with netdev.
Lots of driver updates, particularly of the scale-up and performance
variety. The largest body of core work was Parav's patches fixing and
restructing some of the core code to make way for future RDMA
containerization.
Summary:
- misc small driver fixups to
bnxt_re/hfi1/qib/hns/ocrdma/rdmavt/vmw_pvrdma/nes
- several major feature adds to bnxt_re driver: SRIOV VF RoCE
support, HugePages support, extended hardware stats support, and
SRQ support
- a notable number of fixes to the i40iw driver from debugging scale
up testing
- more work to enable the new hip08 chip in the hns driver
- misc small ULP fixups to srp/srpt//ipoib
- preparation for srp initiator and target to support the RDMA-CM
protocol for connections
- add RDMA-CM support to srp initiator, srp target is still a WIP
- fixes for a couple of places where ipoib could spam the dmesg log
- fix encode/decode of FDR/EDR data rates in the core
- many patches from Parav with ongoing work to clean up
inconsistencies and bugs in RoCE support around the rdma_cm
- mlx5 driver support for the userspace features 'thread domain',
'wallclock timestamps' and 'DV Direct Connected transport'. Support
for the firmware dual port rocee capability
- core support for more than 32 rdma devices in the char dev
allocation
- kernel doc updates from Randy Dunlap
- new netlink uAPI for inspecting RDMA objects similar in spirit to 'ss'
- one minor change to the kobject code acked by Greg KH"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (259 commits)
RDMA/nldev: Provide detailed QP information
RDMA/nldev: Provide global resource utilization
RDMA/core: Add resource tracking for create and destroy PDs
RDMA/core: Add resource tracking for create and destroy CQs
RDMA/core: Add resource tracking for create and destroy QPs
RDMA/restrack: Add general infrastructure to track RDMA resources
RDMA/core: Save kernel caller name when creating PD and CQ objects
RDMA/core: Use the MODNAME instead of the function name for pd callers
RDMA: Move enum ib_cq_creation_flags to uapi headers
IB/rxe: Change RDMA_RXE kconfig to use select
IB/qib: remove qib_keys.c
IB/mthca: remove mthca_user.h
RDMA/cm: Fix access to uninitialized variable
RDMA/cma: Use existing netif_is_bond_master function
IB/core: Avoid SGID attributes query while converting GID from OPA to IB
RDMA/mlx5: Avoid memory leak in case of XRCD dealloc failure
IB/umad: Fix use of unprotected device pointer
IB/iser: Combine substrings for three messages
IB/iser: Delete an unnecessary variable initialisation in iser_send_data_out()
IB/iser: Delete an error message for a failed memory allocation in iser_send_data_out()
...
* pci/misc:
PCI: Add dummy pci_irqd_intx_xlate() for CONFIG_PCI=n build
PCI: Add wrappers for dev_printk()
PCI: Remove unnecessary messages for memory allocation failures
PCI: Add #defines for Completion Timeout Disable feature
hinic: Replace PCI pool old API
net: e100: Replace PCI pool old API
block: DAC960: Replace PCI pool old API
MAINTAINERS: Include more PCI files
PCI: Remove unneeded kallsyms include
powerpc/pci: Unroll two pass loop when scanning bridges
powerpc/pci: Use for_each_pci_bridge() helper
Driver check the wrong register bit in rtl_ocp_tx_cond() that keep driver
waiting until timeout.
Fix this by waiting for the right register bit.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Quectel EP06 is a Cat. 6 LTE modem. It uses the same interface as
the EC20/EC25 for QMI, and requires the same "set DTR"-quirk to work.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this cycle were:
- Updates to use cond_resched() instead of cond_resched_rcu_qs()
where feasible (currently everywhere except in kernel/rcu and in
kernel/torture.c). Also a couple of fixes to avoid sending IPIs to
offline CPUs.
- Updates to simplify RCU's dyntick-idle handling.
- Updates to remove almost all uses of smp_read_barrier_depends() and
read_barrier_depends().
- Torture-test updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
torture: Save a line in stutter_wait(): while -> for
torture: Eliminate torture_runnable and perf_runnable
torture: Make stutter less vulnerable to compilers and races
locking/locktorture: Fix num reader/writer corner cases
locking/locktorture: Fix rwsem reader_delay
torture: Place all torture-test modules in one MAINTAINERS group
rcutorture/kvm-build.sh: Skip build directory check
rcutorture: Simplify functions.sh include path
rcutorture: Simplify logging
rcutorture/kvm-recheck-*: Improve result directory readability check
rcutorture/kvm.sh: Support execution from any directory
rcutorture/kvm.sh: Use consistent help text for --qemu-args
rcutorture/kvm.sh: Remove unused variable, `alldone`
rcutorture: Remove unused script, config2frag.sh
rcutorture/configinit: Fix build directory error message
rcutorture: Preempt RCU-preempt readers more vigorously
torture: Reduce #ifdefs for preempt_schedule()
rcu: Remove have_rcu_nocb_mask from tree_plugin.h
rcu: Add comment giving debug strategy for double call_rcu()
tracing, rcu: Hide trace event rcu_nocb_wake when not used
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJabj6pAAoJEHm+PkMAQRiGs8cIAJQFkCWnbz86e3vG4DuWhyA8
CMGHCQdUOxxFGa/ixhIiuetbC0x+JVHAjV2FwVYbAQfaZB3pfw2iR1ncQxpAP1AI
oLU9vBEqTmwKMPc9CM5rRfnLFWpGcGwUNzgPdxD5yYqGDtcM8K840mF6NdkYe5AN
xU8rv1wlcFPF4A5pvHCH0pvVmK4VxlVFk/2H67TFdxBs4PyJOnSBnf+bcGWgsKO6
hC8XIVtcKCH2GfFxt5d0Vgc5QXJEpX1zn2mtCa1MwYRjN2plgYfD84ha0xE7J0B0
oqV/wnjKXDsmrgVpncr3txd4+zKJFNkdNRE4eLAIupHo2XHTG4HvDJ5dBY2NhGU=
=sOml
-----END PGP SIGNATURE-----
Merge tag v4.15 of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6.git
To resolve conflicts in:
drivers/infiniband/hw/mlx5/main.c
drivers/infiniband/hw/mlx5/qp.c
From patches merged into the -rc cycle. The conflict resolution matches
what linux-next has been carrying.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
- First part of an overhaul of the NuBus subsystem, to bring it up to
modern driver model standards,
- A race condition fix for Mac,
- Defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PZNx
-----END PGP SIGNATURE-----
Merge tag 'm68k-for-v4.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k updates from Geert Uytterhoeven:
- first part of an overhaul of the NuBus subsystem, to bring it up to
modern driver model standards
- a race condition fix for Mac
- defconfig updates
* tag 'm68k-for-v4.16-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
MAINTAINERS: Add NuBus subsystem entry
m68k/mac: Fix race conditions in OSS interrupt dispatch
nubus: Add support for the driver model
nubus: Add expansion_type values for various Mac models
nubus: Adopt standard linked list implementation
nubus: Rename struct nubus_dev
nubus: Rework /proc/bus/nubus/s/ implementation
nubus: Generalize block resource handling
nubus: Clean up whitespace
nubus: Remove redundant code
nubus: Call proc_mkdir() not more than once per slot directory
nubus: Validate slot resource IDs
nubus: Fix log spam
nubus: Use static functions where possible
nubus: Fix up header split
nubus: Avoid array underflow and overflow
m68k/defconfig: Update defconfigs for v4.15-rc1
Wait for a response from the VNIC server before exiting after setting
the MAC address. The resolves an issue with bonding a VNIC client in
ALB or TLB modes. The bonding driver was changing the MAC address more
rapidly than the device could respond, causing the following errors.
"bond0: the hw address of slave eth2 is in use by the bond;
couldn't find a slave with a free hw address to give it
(this should not have happened)"
If the function waits until the change is finalized, these errors are
avoided.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle HRESP error by doing a SW reset of RX and TX and
re-initializing the descriptors, RX and TX queue pointers.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On TTC table creation, the indirection TIRs should be used instead of
the inner indirection TIRs.
Fixes: 1ae1df3a11 ("net/mlx5e: Refactor RSS related objects and code")
Signed-off-by: Gal Pressman <galp@mellanox.com>
Reviewed-by: Shalom Lagziel <shaloml@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When compared to ixgbe and other previous Intel drivers the i40e and i40evf
drivers actually reserve 2 additional descriptors in maybe_stop_tx for
cache line alignment. We need to update DESC_NEEDED to reflect this as
otherwise we are more likely to return TX_BUSY which will cause issues with
things like xmit_more.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure to cancel any pending work that might update driver coalesce
settings when taking down an interface.
Fixes: 6a8788f256 ("bnxt_en: add support for software dynamic interrupt moderation")
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the frame check sequence (FCS) is split across the last two frames
of a fragmented packet, part of the FCS gets counted twice, once when
subtracting the FCS, and again when subtracting the previously received
data.
For example, if 1602 bytes are received, and the first fragment contains
the first 1600 bytes (including the first two bytes of the FCS), and the
second fragment contains the last two bytes of the FCS:
'skb->len == 1600' from the first fragment
size = lstatus & BD_LENGTH_MASK; # 1602
size -= ETH_FCS_LEN; # 1598
size -= skb->len; # -2
Since the size is unsigned, it wraps around and causes a BUG later in
the packet handling, as shown below:
kernel BUG at ./include/linux/skbuff.h:2068!
Oops: Exception in kernel mode, sig: 5 [#1]
...
NIP [c021ec60] skb_pull+0x24/0x44
LR [c01e2fbc] gfar_clean_rx_ring+0x498/0x690
Call Trace:
[df7edeb0] [c01e2c1c] gfar_clean_rx_ring+0xf8/0x690 (unreliable)
[df7edf20] [c01e33a8] gfar_poll_rx_sq+0x3c/0x9c
[df7edf40] [c023352c] net_rx_action+0x21c/0x274
[df7edf90] [c0329000] __do_softirq+0xd8/0x240
[df7edff0] [c000c108] call_do_irq+0x24/0x3c
[c0597e90] [c00041dc] do_IRQ+0x64/0xc4
[c0597eb0] [c000d920] ret_from_except+0x0/0x18
--- interrupt: 501 at arch_cpu_idle+0x24/0x5c
Change the size to a signed integer and then trim off any part of the
FCS that was received prior to the last fragment.
Fixes: 6c389fc931 ("gianfar: fix size of scatter-gathered frames")
Signed-off-by: Andy Spencer <aspencer@spacex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was found that ethtool provides unexisting module name while
it queries the specified network device for associated driver
information. Then user tries to unload that module by provided
module name and fails.
This happens because ethtool reads value of DRV_NAME macro,
while module name is defined at the driver's Makefile.
This patch is to correct Cavium CN88xx Thunder NIC driver names
(DRV_NAME macro) 'thunder-nicvf' to 'nicvf' and 'thunder-nic'
to 'nicpf', sync bgx and xcv driver names accordingly to their
module names.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lockless access to __ptr_ring_full is only legal if ring is
never resized, otherwise it might cause use-after free errors.
Simply drop the lockless test, we'll drop the packet
a bit later when produce fails.
Fixes: 362899b8 ("macvtap: switch to use skb array")
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
mt76
* validate CCMP PN from received frames to avoid replay attacks
qtnfmac
* support 64-bit network stats
* report more hardware information to kernel log and some via ethtool
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJaa1x7AAoJEG4XJFUm622bdc8H/3JSWFnXlkrQvjZzL1NWR0Hn
vUYou/W04mgzYtXIcscNL3otDa9TGwLW6Sr5wP0MDH/TGU9zXoEZxBxnYy4zq4np
7ZP7M6VsOzOhlNNsTcNAiMGyObtIT4btrfKlmp2yvf3Sra7nHNJJmprFeuyH3f02
vk5ZQWjMcEAe0afBGPcHrzndoAvVqIHHOAbM/w694n/8cdT8edcQeQ8rwlFO6ENU
db9yqkr4RvjWv9oJwa2us6d0lolJDk8ATWhDTyZL40X9yk84XR7E0jMdN5LQ/CJj
CCCMWsDYjUpEDUJVmwLdXzGavgo43QAs9a+O+z7MDJ4uwqYkZh3rzQZay+dYLKk=
=D4LX
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.16
Major changes:
wil6210
* add PCI device id for Talyn
* support flashless device
ath9k
* improve RSSI/signal accuracy on AR9003 series
mt76
* validate CCMP PN from received frames to avoid replay attacks
qtnfmac
* support 64-bit network stats
* report more hardware information to kernel log and some via ethtool
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
efx_default_channel_want_txqs() is only used in efx.c, while
efx_ptp_want_txqs() and efx_ptp_channel_type (a struct) are only used
in ptp.c. In all cases these symbols should be static.
Fixes: 2935e3c382 ("sfc: on 8000 series use TX queues for TX timestamps")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[ecree@solarflare.com: rewrote commit message]
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
