Implement ndo_udp_tunnel_{add,del} to update the NIC's list of VXLAN and
GENEVE UDP ports. Also reset the port list to empty on driver load and
on driver unload, with appropriate flag set on the unload case.
These port numbers are used for RX inner checksum offload, and in future
will also be used for TX inner checksum offload and encapsulated TSO.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function wasn't being called in this particular case when the MC
reboots. This caused resource reallocations to not be handled properly
and often ended up disabling the interface.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is mainly to prepare for a future overlay networking patch that
could cause an MC reset at probe time if the UDP tunnel port list is
set immediately upon driver load.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the csum_level for encapsulated packets where the encapsulation
type, l3 class and l4 class are sets that need it.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RX checksum offload of encapsulated packets. This
essentially just means paying attention to the inner checksum flags
in the RX event, and if *either* checksum flag indicates a fail then
don't tell the kernel that checksum offload was successful.
Also, count these checksum errors and export the counts to ethtool -S.
Test the most common "good" case of RX events with a single bitmask
instead of a series of ifs. Move the more specific error checking
in to a separate function for clarity, and don't use unlikely() there
since we know at least one of the bits is bad.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The kernel resolves the nexthops for a given route using
FIB_LOOKUP_IGNORE_LINKSTATE which means a notification can be sent for a
route with one of its nexthops being LINKDOWN.
In case IGNORE_ROUTES_WITH_LINKDOWN is set for the nexthop netdev, then
we shouldn't reflect the nexthop to the device's table.
Once the nexthop netdev's carrier goes up we'll be notified using NH_ADD
and reflect it to the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the last IP address is removed from a netdev, its RIF is deleted.
However, if user didn't first remove neighbours and nexthops using this
interface, then they would still be present in the device's tables.
Therefore, whenever a RIF is deleted, make sure all the neighbours and
nexthops (adjacency entries) using it are removed from the relevant
tables as well.
The action associated with any route using this RIF would be refreshed,
most likely to trap. If the kernel decides to remove the route (f.e.,
because all the nexthops are now DEAD), then an event would be sent,
causing the route to be removed from the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a packet hits a multipath route in the device's routing table, a
hash is computed over its headers, which is then used to select the
appropriate nexthop from the device's adjacency table.
There are situations in which the kernel removes a nexthop from a
multipath route (e.g., no carrier) and the device should do the same.
Upon the reception of NH_{ADD,DEL} events, add or remove a nexthop from
the device's adjacency table and refresh all the routes using the
nexthop group. If all the nexthops of a multipath route are invalid,
then any packet hitting the route would be trapped to the CPU for
forwarding.
If all the nexthops are DEAD, then the kernel would remove the route
entirely. On the other hand, if all the nexthops are merely LINKDOWN,
then the kernel would keep the route and forward any incoming packet
using a different route.
While the last case might sound like a problem, it's expected that a
routing daemon running in user space would remove such a route from the
FIB as it's dumped with the DEAD flag set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device can have one of three actions associated with a route:
1) Remote - packets continue to the adjacency table
2) Local - packets continue to the neighbour table
3) Trap - packets continue to the CPU
The first two actions can also trap packets to the CPU, but they do so
using a different trap ID, which has a lower traffic class and less
allotted bandwidth.
We currently use the third action for both RTN_{LOCAL,BROADCAST} routes
and RTN_UNICAST routes not pointing to the switch ports.
However, packets that merely need to be forwarded by the switch are
likely not control packets and can be therefore scheduled towards the
CPU using a lower traffic class.
Achieve the above by assigning the third action only to local and
broadcast routes and have any other route use either of the first two
actions, based on whether the route is gatewayed or not.
This will also allow us to refresh routes using the local action and
have them trap packets when their RIF is no longer valid following a
NH_DEL event.
One side effect of this patch is that we no longer give special
treatment to multipath routes using both switch and non-switch ports
towards their nexthops. If at least one of the nexthops can be resolved,
then the device will forward the packets instead of trapping them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous patch introduced a generic function to determine whether a
route should be offloaded or not. Make use of it here.
In the future we're going to add more conditions to this test (e.g.,
whether TOS is non-zero), so it makes sense to centralize it instead of
open coding it in a few places.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently set the RTNH_F_OFFLOAD flag for all routes using remote
action, but this isn't always correct. If none of the nexthops
associated with a gatewayed route can be offloaded into the device, then
any packet hitting it would be trapped to the CPU and forwarded by the
kernel.
Solve this by pushing the setting of the offload flag to after the route
was programmed into the device, thereby allowing us to take all the
parameters into account.
This change will also help us further in the patchset, when we refresh
routes following the reception of NH_{ADD,DEL} events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nexthop init and de-init functions both have symmetric parts
concerned with the reflection of the neighbour entry into the device's
adjacency table, in case it's used by a gatewayed route.
These sections of code also need to be called when a nexthop is marked
as valid / invalid following NH_{ADD,DEL} events. Break these out into
appropriate functions, so that they could be invoked following the
reception of above events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the previous changes, the FIB info is embedded in every nexthop
group struct, which in turn is embedded in every FIB entry struct.
We can therefore safely remove the FIB info from the entry struct. This
has the added advantage of making the router-related structs more
generic and suitable for use with IPv6 offloads.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, the only FIB entries that were associated with a nexthop
group were routes to remote networks where all the nexthop devices had a
valid router interface (RIF). This is in contrast to the FIB code,
where all the routes are associated with a FIB info. The same design
choice needs to be applied to the driver's cache.
Based on the NH_{ADD,DEL} events which will be added later in the
patchset, we need to be able to change the action (forward / trap)
associated with all the routes using the nexthop group. However, if we
can't link between the nexthop and the routes using it, then the above
is impossible.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch is going to generalize the way in which we store routes.
Instead of attaching a nexthop group only to gatewayed routes, one will
be attached to each route, in a similar way to the way the FIB code
stores its routes.
The above means that any function operating on a nexthop group cannot
assume the group represents only gatewayed nexthops. One such function
is the one that refreshes a nexthop group and updates the adjacency
table following nexthop changes.
For a nexthop group that doesn't represent any gateways this function
would essentially be a NOP, but it would be useful if it did update the
action associated with any route using it. This will allow us to later
consolidate code paths when a nexthop changes following NH_{ADD,DEL}
events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use the scope of the FIB info to distinguish between a
direct unicast route and a gatewayed one. However, the kernel is
perfectly happy to configure a route with scope UNIVERSE to a directly
connected network.
Instead, we can rely on the first nexthop's scope to check if the route
is gatewayed or not.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Later in the patchset we'll add the NH_{ADD,DEL} events which will let
us know when a nexthop is considered to be dead. Based on these events
we need to be able to add or remove the nexthop from the device's
tables.
Therefore, store the private nexthop structs in a hash table and use the
kernel's fib_nh struct as the key, so that we'll be able to easily find
them when the events are received.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we're notified about a new RTN_UNICAST route we perform
a lookup on the nexthop group list looking for a group with a matching
configuration to that found in the FIB info. This is quite inefficient.
Instead, we can simply rely on the kernel to consolidate several FIB
configurations into the same FIB info and use the FIB info as the key
for our private nexthop group struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we invalidate a nexthop we should also invalidate its neighbour
entry pointer as it might be destroyed later on. This makes the nexthop
de-init function symmetric with its init and also ensures nobody will
try to access the neighbour entry.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No rollback is needed since the chain is in consistent state and
mlxsw_afa_block_destroy() will take care of putting it away. So remove
the one we have now which is wrong. Also move the set of 'finished' flag
to the beginning of the function, because the block is certainly unusable
for future action addition no matter if the function succeeds or not.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 4cda7d8d70 ("mlxsw: core: Introduce flexible actions support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch complains about two unsigned without type after.
Since the value return is u32, it is simpler to replace it by u32 instead
of "unsigned int"
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The u64 x variable in sysfs_display_ring is unused.
This patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit cf32deec16 ("stmmac: add tx_skbuff_dma to save descriptors used by PTP"),
the struct dma_desc *p in stmmac_tx_clean was not used at all.
This patch remove this dead code.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a PHY is found, printing which one was found (and which type/model) is
a good information to know.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool stat counter rx_crc from stmmac is mis-named, the name
seems to speak about the number of RX CRC done, but in fact it is about
errors.
This patch rename it to rx_crc_errors, just like the same ifconfig
counter.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rewrite two test against NULL value with correct style.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The message about invalid speed does not state 1000 as a valid speed.
It is much simpler to said that the speed is invalid.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As said by checkpatch ENOSYS means 'invalid syscall nr' and nothing
else.
This patch replace ENOSYS by the more appropriate value EINVAL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dwmac_dma_reset function use an open coded of readl_poll_timeout().
Replace the open coded handling with the proper function.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_mdio_busy_wait() function do the same job than
readl_poll_timeout().
So is is better to replace it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch complains about some code style problem on stmmac_mdio.c.
This patch fix them.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about asm/io.h.
Sorting all includes in the process.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the checkpatch warning about free software address.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix some typos in comments.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bus_setup function pointer is not used at all, this patch remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the define MAC_RNABLE_RX have a typo, rename it to MAC_ENABLE_RX
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We have many gro cells users, so lets move the code to avoid
duplication.
This creates a CONFIG_GRO_CELLS option.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qualcomm/emac/emac-ethtool.c:155:49-50: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Timur Tabi <timur@codeaurora.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LED Mode:
Microsemi PHY support 2 LEDs (LED[0] and LED[1]) to display different
status information that can be selected by setting LED mode.
LED Mode parameter (vsc8531, led-0-mode) and (vsc8531, led-1-mode) get
from Device Tree.
Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch doesn't affect how the code works.
My static checker complains that the mask and shift doesn't make sense
because 0xffffff << 16 goes beyond the end of 32 bits. It should be
0xffff instead but the existing code won't cause runtime bugs.
Also the casting here is not needed and not consistent with the rest of
the code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix smatch errors by not dereferencing iq pointer if it's NULL.
See http://marc.info/?l=kernel-janitors&m=148637299004834&w=2
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Load correct firmware in rtl8192ce wireless driver, from Jurij
Smakov.
2) Fix leak of tx_ring and tx_cq due to overwriting in mlx4 driver,
from Martin KaFai Lau.
3) Need to reference count PHY driver module when it is attached, from
Mao Wenan.
4) Don't do zero length vzalloc() in ethtool register dump, from
Stanislaw Gruszka.
5) Defer net_disable_timestamp() to a workqueue to get out of locking
issues, from Eric Dumazet.
6) We cannot drop the SKB dst when IP options refer to them, fix also
from Eric Dumazet.
7) Incorrect packet header offset calculations in ip6_gre, again from
Eric Dumazet.
8) Missing tcp_v6_restore_cb() causes use-after-free, from Eric too.
9) tcp_splice_read() can get into an infinite loop with URG, and hey
it's from Eric once more.
10) vnet_hdr_sz can change asynchronously, so read it once during
decision making in macvtap and tun, from Willem de Bruijn.
11) Can't use kernel stack for DMA transfers in USB networking drivers,
from Ben Hutchings.
12) Handle csum errors properly in UDP by calling the proper destructor,
from Eric Dumazet.
13) For non-deterministic softirq run when scheduling NAPI from a
workqueue in mlx4, from Benjamin Poirier.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
sctp: check af before verify address in sctp_addr_id2transport
sctp: avoid BUG_ON on sctp_wait_for_sndbuf
mlx4: Invoke softirqs after napi_reschedule
udp: properly cope with csum errors
catc: Use heap buffer for memory size test
catc: Combine failure cleanup code in catc_probe()
rtl8150: Use heap buffers for all register access
pegasus: Use heap buffers for all register access
macvtap: read vnet_hdr_size once
tun: read vnet_hdr_sz once
tcp: avoid infinite loop in tcp_splice_read()
hns: avoid stack overflow with CONFIG_KASAN
ipv6: Fix IPv6 packet loss in scenarios involving roaming + snooping switches
ipv6: tcp: add a missing tcp_v6_restore_cb()
nl80211: Fix mesh HT operation check
mac80211: Fix adding of mesh vendor IEs
mac80211: Allocate a sync skcipher explicitly for FILS AEAD
mac80211: Fix FILS AEAD protection in Association Request frame
ip6_gre: fix ip6gre_err() invalid reads
netlabel: out of bound access in cipso_v4_validate()
...
This bug is harmless because it's just a sanity check and we always
pass valid values for "encap_type" but the test is off by one.
Fixes: 9b41080125 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for enabling or disabling the lane swapping (called
"port mirroring" in PHY's CFG4 register) feature of the DP83867 TI's PHY
device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as off
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
