Add SSID information to the net-detect indication to userspace. Fetch
the matched profiles from the firmware in order to find the correct
SSIDs in the profiles that matched.
Since the net-detect information is stored in cfg80211, and in theory
it could change while we are waking up and reading the matched
profiles, we need to save it when we enter D3 so it is available
during resume.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A following patche will use trans_pcie->cmd_in_flight
for reference accounting as well. get ready for it.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
IWL_MVM_REF_PROTECT_CSA is missing from the ref strings
used by debugfs.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this TLV flag set.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
All the supported firmwares have this TLV flag set.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This firmware is not supported anymore.
Stop loading this firmware - and remove the code that
handled older versions.
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Query the firmware for scan offload matches when waking up in order to
report net detect as the reason for the wake up.
This requires a new command API to be implemented. Additionally,
remove some net detect command entries that are not valid anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware file-format is described in iwl-fw-file.h, while the
internal handling structures and functions are in iwl-fw.h.
Fix the separation between the files by moving file format
definitions to iwl-fw-file.h.
Also add a missing description for a kernel-doc member, and it's
not needed to include iwl-fw-file.h again from the code (thanks
to Liad Kaufman).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a new SDIO card id intended for the new 4165 series.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of channel switch, we need to teardown the TDLS peers.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver knows whether an rx frame was beamformed and marks
it in the radiotap VHT flags. However it should also declare
that it knows to extract this info otherwise this gets discarded
by sniffers like Wireshark.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add suspend/resume trans ops that will be called from
mac80211's suspend/resume ops.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the device wakes up due to netdetect, we need to query different
things from the firmware than when it wakes up with a normal WoWLAN.
To make this easier, separate the netdetect wake up handling from the
rest. For now, we don't send netdetect as a wake up reason, treating
it as a non-wireless wake up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor the iwl_mvm_query_wakeup_reasons() function to split the part
that gets the firmware status from the part that sets up the WoWLAN
status. This will allow netdetect to reuse the code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to send a WOWLAN_CONFIGURATION command also for netdetect and
configure the rfkill release trigger if needed. To do so, refactor
the code that configures wowlan and netdetect when suspending and send
the WOWLAN_CONFIGURATION command also for net_detect.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add the net detect WoWLAN flag to indicate support and use the
nd_config from the WoWLAN configuration to start net detect, if it is
set. The WoWLAN configuration takes precedence over the debugfs
configuration.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When another vif is also running during a channel switch, we need to
use a session protection when we move to the new channel, so that we
don't miss the beacons. Without this, sometimes the other vif
repeatedly gets time exactly when we should be hearing the beacons,
preventing channel switch from completing. Adding a session
protection that lasts from the moment the channel changes until 2
TBTTs later, ensures that we will hear the beacons on the destination
channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
If setting the CSA time event fails, we must clear the TE data,
otherwise we'll try to remove it when, for instance, a disconnection
occurs, causing a SYSASSERT.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
After a channel switch, transmission on the new channel is only
started once we see a beacon on it. Thus, beacon filtering needs to
be disabled during channel switch so that mac80211 receives this
beacon and finishes the process.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We need to call ieee80211_chswitch_done() ourselves just when the
absence TE started, so we perform the actual context switch early
enough. To do so, add a dummy channel_switch op, which will cause
mac80211 to skip the countdown timer and allow us to call
ieee80211_chswitch_done() to complete the operation.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Now that mac80211 waits for the first beacon on the new channel before
calling post_channel_switch, the reconfiguration of the firmware
should be done in the post_channel_switch operation instead of when
assigning the vif to the new context.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Instead of using a hardcoded number of TUs before beacon 0 as the time
to start the absence and actual channel switch, calculate it in
relation to the beacon interval. We use 10 TUs + beacon interval
before beacon 0 to target a bit before beacon 1. This gives us enough
time to switch to the new channel before the AP/GO switches.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Add an absent time event when pre_channel_switch is called and use the
time event started indication to set the disable_tx bit instead of
doing it in unassign_vif(). This is done so that the firmware queues
are stopped before the actual switch takes place to avoid losing
packets while the AP/GO is performing its actual switch.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Now that all CSA flows are using the switch_vif_chanctx op, we can
rely on the switching_chanctx boolean that is passed to the
__iwl_mvm_assign_vif_chanctx() and __iwl_mvm_unassign_vif_chanctx()
functions to decide whether the context switch flows need to be
executed. In this way we make the chanctx switch flow more generic,
without having to rely on the csa_active flag being set.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Disable PS when pre_channel_switch is called and add the
post_channel_switch operation to re-enable PS when the channel switch
is completed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
The spec requires to decrement the CSA counters based on TBTT,
regardless if the beacon was actually transmitted. Previously, the fw
would send beacon notifications only for successfully transmitted
beacons. This behavior resulted in inaccurate CSA countdown. In order
to address this issue, the fw was changed to send beacon
notifications also for not transmitted beacons. Such notifications
have TX_STATUS_INTERNAL_ABORT (0x92).
Don't start the CSA countdown before first successfully transmitted
beacon, in order to guarantee that the CSA is announced for a
required period.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
We have code to recover and go back to the original channel context if
something fails in the middle of switch_vif_chanctx, but we return the
error code of the recover calls instead of the original code, so if
the recovery succeeds, we will return 0 (success). Fix this by not
assigning the return value of the recovery calls to ret.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Add support to reassign vif in switch_vif_chanctx. This is similar to
the existing CHANCTX_SWMODE_SWAP_CONTEXTS mode, but doesn't delete the
old context nor creates a new one, doing to switch between two
existing contexts.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Currently we only support the CHANCTX_SWMODE_SWAP_CONTEXTS mode, but
we need to support other modes as well. Spin a new function off in
order to make it easier to support other modes.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
We only need the csa_vif in AP/GO modes, and assigning for other
interfaces may cause problems, because csa_vif is never cleared. To
prevent this, only assign the value if the iftype is
NL80211_IFTYPE_AP. Use a switch to do this, even though, for now,
only the AP interface type is handled, because soon other interface
types will be added as well.
Additionally, convert the WARN() in the error case when a
channel-switch is already running to WARN_ONCE().
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
A new callback has been added to prepare the device for a channel
switch. Use the new callback instead of the old channel_switch_beacon
operation.
This makes it possible to remove the channel_switch_beacon operation
from mac80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Maintain a TDLS channel-switch state and update it according to
notifications from FW and timeouts. Explicitly check all state
transitions are valid.
When switching is initiated by mac80211, use a delayed work to
periodically reschedule it from iwlwifi.
Give the FW mac80211 generated TDLS channel-switch request/response
templates. It will change appropriate values (switch timings) and Tx
them at appropriate times.
Enable the channel switch wiphy capability bit when the FW supports it.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Block TID 4 (VI) on a vif when using TDLS. This TID will be used by FW
for TDLS channel-switch requests and PTI requests.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When adding a TDLS station, allocate 4 new queues for it. Configure them
to FW and enable them. On station removal, drain the queues if needed
and disable them when empty.
Make sure to flush all packets in the private queues of TDLS stations in
the mac80211 flush() callback.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TDLS peers are present the FW will send packets on a dedicated
TID vs. the peer when performing TDLS channel-switches. The driver
configures the TID on connection to the peer and the FW is responsible
for maintaining the state of QoS seqno and PN/IV for encryption.
If the FW asserts, the driver cannot correctly reconfigure the starting
seqno/PN to the reloaded FW, thus forcing us to reconnect the peer.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
TDLS stations will have private queues, so consider them as well when
allocating a new one. Consolidate the HW-queue iterating code into
a single exported function, to be used by the TDLS code in the future.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Send a dedicated TDLS_CONFIG command when a TDLS peer joins/leaves. The
fields for the command are mostly place-holders, as most of the FW
functionality is not implemented. In the future the dedicated FW TID
will be used for channel-switching and buffer-sta functionality.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a channel-switch command and a switch-start notification. Also add a
FW TLV bit indicating TDLS channel switching support.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver/FW combination now support TDLS.
Check the FW support with the TLV bit.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we pre-populate the skb->head for the stack, we only pull
in the 802.11 header including crypto (assuming the packet isn't
short enough to be in there completely.) This is fine, but in
ieee80211_data_to_8023() we later unconditionally pull 8 more
bytes for the SNAP header and ethertype field (except for mesh
or 4-addr, where it's even more, but we don't care as much about
them).
Avoid the additional later pull by pulling in those 8 bytes here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we pre-populate the skb->head for the stack, we only pull
in the 802.11 header (assuming the packet isn't short enough to
be in there completely.) This is fine, but in many cases we'll
pull in the crypto headers pretty much immediately afterwards,
so to avoid that pull in the crypto header early.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of building the rx_status on the stack and then
copying it to the skb, allocate the skb a bit earlier
and then build the rx_status in place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: IdoX Yariv <ido@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the original driver, we decided to not implement WEP RX hardware
offload because of a quirk with the firmware API - it allows setting
global WEP keys that then get used for all virtual interfaces, which
is clearly wrong if more than one exists, and it allows setting per-
station keys but then separates multicast and unicast keys.
In order to implement WEP RX hardware offload, work around these
limitations by uploading each WEP key twice, once as multicast and
once as unicast, but point them both to the same key slot (offset)
and use the same key material so the slot overwrite on the second
upload doesn't actually change anything. Upon removal, also remove
the key twice so the station no longer references it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor the key add/remove functions to be able to reuse parts
of them later for RX WEP keys, which need to be uploaded twice.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a flow that handles the requests to cancel the roc time event,
that has been triggered via the aux framework.
The roc for bss is different than the roc for p2p devices, and is done
via the aux framework using the aux queue, thus requires a different flow
to cancel the time event.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove warning on scan complete with unknown ID, since this
scan could be already cleared in abort flow.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The ssid_bitmap should be unsigned, though it doesn't matter
much as the high bits aren't used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Identify 7265-D devices using the hardware revision (they have the
same PCI IDs as 7265) and change the configuration for them taking
the differences (currently only the firmware image) into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Older firmwares do not provide support for the HOT_SPOT_CMD command.
Check for the appropriate TLV flag that declares hotspot support in
the firmware to prevent a firmware assertion failure that can be
triggered from the userspace,
Cc: stable@vger.kernel.org [3.17+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Toggle the LMPM_CHICK register when writing chunks into the FW's extended
SRAM. This tells the FW to put the chunk into a different memory space.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no reason to pass every 50th beacon if
nothing was changed.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of allocating nd_ies separately, make it part of the iwl_mvm
structure so it's easier to handle its lifetime.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We were toggling the wrong bit when we reset the device,
fix that. Moreover, since the reset can take time, we need
to wait before we set the rfkill interrupt. Not doing so
can be racy since the driver is enabling the rfkill
interrupt while the device is resetting which will clear
all the registers including the CSR_INT_MASK.
This can basically lead to a situation where we don't
enable the rfkill interrupt. If that happens, the user will
not be able to re-enable the device when de-asserting
rfkill.
This scenario happened to the submitter of:
https://bugzilla.kernel.org/show_bug.cgi?id=87191
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For background and scheduled scan, using the new unified scan API,
support random MAC address scanning.
Unfortunately, the firmware right now doesn't support randomising
itself, so for now do it on the host - we'll change this once the
firmware supports randomising the address for each scan iteration
using the address/mask.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
LMAC TLV bit may be on in FWs that support UMAC scan; so check
for UMAC TLV bit first.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The fw now indicates missing BA with ampdu_ack_len=0.
This will make the whole aggregation being marked
as failed, although it's most likely not the case (and
only the BA itself was failed).
Consider this case as a single tx failure.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The TTC and RRC features are supported by the newer
firmwares. It allows to reach better overall WiFi and BT
performance. When the RRC is enabled, we don't need to force
the AP to send SISO frames, but it can keeps sending MIMO
frames.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This API uses second CPU scan commands, and can support multiple
simultaneous scans.
Adding the new API, and adding new mechanisms to deal with up to
8 simultaneous scans instead of the old scan status.
New scan API requires scan configuration for default scan parameters,
adding it in _up flow. Also updating scan configuration after updating
valid scan antennas via debugfs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The driver must set the keep alive period regardless of power
management state. The keep alive period must be greater or equal to
both the NIC's maximum sleep period, and the listen interval.
However, we were confusing time units (TU) and msec, so fix that.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our firmware scheduler suffers from false wake-up on 500 time units.
that is if the dtim interval exceeds 500 time units, the fw wakes up,
understands that the next wake-up event is still ahead, and if this event
is more than 10msec in the future - goes back to sleep, otherwise - stay
awake. For example, say that the beacon interval is 101 and the dtim
period is 5, the dtim interval is 101 x 5 = 505, and we will stay awake
for those extra 5msec.
So on the one hand the dtim interval should be congruent to the beacon
interval times the dtim period, and on the other should minimize
the false wake-ups event.
This change applies only to D0/D3 power modes.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The deferred d0i3 exit is currently implemented in the
resume op, which is called when mac80211 starts its
resume process.
However, mac80211 still doesn't handle frames at this stage,
which results in frames being dropped.
Move the deferred d0i3 handling to the reconfig_complete
callback, in order to make sure mac80211 is fully available
at this point.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
After the corresponding mac80211 patch, we can now report the airtime
used for each transmitted packet and mac80211 will be able to implement
WMM-AC with that information.
To support WMM-AC in the driver then, report the airtime and advertise
support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add two new parameters to iwl_cfg:
max_ht_ampdu_exponent and max_vht_ampdu_exponent.
These parameters, if set, will set new values to the maximum of
HT and VHT A-MPDU exponent for the A-MPDU length exponent.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since it's too complicated for the fw to insert a DS Parameter Set
element in the middle of the frame, it was decided that it should be
done by the host. The fw will only parse the frame and update the
current channel field.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When aborting d0i3 due to taken refs, other threads might
already wait on d0i3_exit_waitq for IWL_MVM_STATUS_IN_D0I3
to get cleared (it's somewhat likely, as synchronize_rcu()
might take a while), so make sure to wake them up.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some rare cases, the firmware can put the device to
sleep after the driver requested the access. This is
because the access request can take a short time to be
propagated to the firmware.
If that happens, the driver may think that it has access
since the firmware hasn't put the device to sleep yet, but
right after the driver's check, the firmware might put the
device to sleep.
Warn when this happens by allowing the firmware to finish
the "put the device sleep" flow so that the driver will
not get access to the device. This will make the issue
visible.
This still doesn't fix the race, but at least it makes
it more visible.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently, the firmware only sends temperature notificaitions inside
RX statistics notifications, which are tied to beacon filtering. This
is a problem because beacon filtering is not used with vifs that don't
receive beacons (e.g. P2P GO and AP), so the driver doesn't receive
temperature notifications in those cases. To solve that, the firmware
will be changed so that it sends DTS_MEASUREMENT_NOTIFICATIONs,
independently from the beacon filtering flows.
To support that, the driver needs to also handle unsolicited
DTS_MEASUREMENT_NOTIFICATIONs, that are not triggered by
DTS_TRIGGER_CMD_FLAGS_TEMP requests.
This change is backwards compatible and will simply not be used with
firmware versions that do not send the notifications.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Refactor the temperature handling code so that it is easier to reuse
it with other notification flows.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The code to capture firmware errors works during the reconfiguration
phase after an error. As the D3->D0 transition uses the same flow to
get the D0 image reconfigured, this triggered and caused a firmware
coredump to be collected. This in turn, if it isn't picked up by
userspace, can cause module unloading to fail, which is how the bug
was detected.
To fix this issue, introduce a new status flag (D3_RECONFIG) and use
it to detect that during reconfiguration no coredump should be taken
and reported.
Reported-by: Avi Kraif <avix.kraif@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When we need only one antenna, we should refrain from using
the antenna that is shared with BT if BT load is high.
Fix this.
Reviewed-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When Tx STBC is being used and RS switches to a search column
using the alternate antenna from the current one there is a
problem with using rs_rate_match to figure out which table
is the active and which one is the search one. The root cause
is because in STBC the antenna mask in the ucode rate is set
to ANT_AB and in this specific scenario it matches both the
active and search table (e.g. SISO_ANT_A and SISO_ANT_B).
This leads to tx stats being updated in the wrong table and later
on to getting stuck in a test window and not moving on to other
columns. If this happens during the initial search cycle we
never end it and therefore never enable aggregation which leads
naturally to severe througput degradation.
Fix it by deducing which table is which by knowing whether we're
in a search or not like it's being done in rs_rate_scale_perform
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Other contexts might call iwl_mvm_ref_sync() right before
we set IWL_MVM_STATUS_IN_D0I3, and then assume the fw/bus
is not in d0i3 state.
However, since we currently don't check for held references
in the d0i3_enter flow, we might enter d0i3 although there
is an active reference.
Solve it by aborting the d0i3 enter flow if there is an
active reference. Since users are assumed to use
iwl_mvm_ref_sync, which takes a ref before checking the
flag, we don't need further locking.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This was taken care of in case we're doing STBC with HT
but not when working with VHT.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Even if running the driver with param init_dbg=1 - on INIT
image error - iwl_trans_stop_device() was still called. This
patch fixes that and calls iwl_trans_stop_device() on INIT
image failure only if init_dbg=0.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The length counting previously done had an error in it, causing
the length down the data dumping function to be shorter than it
should be, causing the end of the data to get truncated off and
lost.
Cc: <stable@vger.kernel.org> [3.17+]
Fixes: 67c65f2cf7 ("iwlwifi: dump periphery registers to fw-error-dump")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The variable 'tid' is already defined in this function, so use
just 't' for the new one. As we return from the function just
overwriting 'tid' would be acceptable, but less obvious to the
reader.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Mostly functions related to building Tx-commands for sending to FW.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The status variable should be unsigned as the function call
requires a u32 not int pointer, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions
-----BEGIN PGP SIGNATURE-----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=6GIj
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-11-04' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This relatively large batch of changes is comprised of the
following:
* large mac80211-hwsim changes from Ben, Jukka and a bit myself
* OCB/WAVE/11p support from Rostislav on behalf of the Czech Technical
University in Prague and Volkswagen Group Research
* minstrel VHT work from Karl
* more CSA work from Luca
* WMM admission control support in mac80211 (myself)
* various smaller fixes, spelling corrections, and minor API additions"
Conflicts:
drivers/net/wireless/ath/wil6210/cfg80211.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the RFkill interrupt fires while we calibrate, it would
make the firmware fail and the driver wasn't able to recover.
Change the flow so that the driver will kill the firmware
in that case.
Since we have now two flows that are calling
trans_stop_device (the RFkill interrupt and the
op_mode_mvm_start function) - we need to better sync this.
Use the STATUS_DEVICE_ENABLED in the pcie transport in an
atomic way to achieve this.
This fixes: https://bugzilla.kernel.org/show_bug.cgi?id=86231
CC: <stable@vger.kernel.org> [3.10+]
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix my mistake while sending Johannes's
commit aadede6e9f
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Oct 9 17:01:36 2014 +0200
iwlwifi: mvm: port to devcoredump framework
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scan reference wasn't released in case of offloaded scan,
causing the refcount to go wrong and prevent the device
from going into d0i3.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
STBC is enabled on HT/VHT SISO rates in case we don't care
about power consumption and it won't hurt BT.
This is done only in case the peer and our chip support STBC
of course.
While at it fixed a bug which was causing bw and ldpc
flags to be set incorrectly in the rate scale table in case
we are switching to a legacy Tx column. This had no real impact.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Scan condition iterator assumes that an interface is associated if
phy_ctxt is assigned, but this isn't the sutuation in P2P device.
OTOH P2P device is never associated so we can simply ignore it.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwlwifi features a debug mechanism that allows to dump
binary data which is helpful to debug the firmware.
Until now, this data was made available for the userspace
through debugfs. For this exact purpose, devcoredump was
created. Move to the new infrastructure.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These chips support STBC in both Tx and Rx.
Given that we've added STBC Tx support enable it.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mvm->cur_ucode wasn't set before we actually load the
firmware. This caused issues when we boot in RFKILL since
we get an RFKILL interrupt upon boot even before we load
any firmware.
This leads to issues since iwl_mvm_set_hw_rfkill_state
(the RFKILL interrupts handler in mvm) relies on this
variable.
Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Precedence of & and >> is not the same and is not left to right.
shift has higher precedence and should be done after the mask.
Add parentheses around the mask.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We used to need to include some headers in order to read the registers
and do all the calculations by ourselves, but this is not done anymore
(i.e. we let the firmware do this for us), so we don't need to include
those headers anymore.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
For WMM-AC we may have to be changing QoS parameters while the
queues are being flushed. This is not relevant in the "drop"
case, but matters when we wait for the device to finish the
transmissions.
To allow this, do the actual waiting without holding the mutex.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The warning gives no information about the frame, and presents
the flags so that one might think they're the frame. Clarify
and add more information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is unused and won't be available in some future invocations of the
function.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The MVM_FW_BCAST_FILTER_PASS_ALL option defined in iwl-dbg-cfg.ini
configuration file allows to enable/disable FW broadcast filtering.
If MVM_FW_BCAST_FILTER_PASS_ALL is not defined in iwl-dbg-cfg.ini or
its value is 0, the mvm broadcast filtering is enabled.
Setting MVM_FW_BCAST_FILTER_PASS_ALL=1 in iwl-dbg-cfg.ini blocks sending
of BCAST_FILTER_CMD to FW.
Signed-off-by: Max Stepanov <Max.Stepanov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the new format the "CSS section" has the same TLV type
as the "mem section". So we need to run the secured flow
for all the 8000 products.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the ARC is reset when we exit from Sx in case we had
WoWLAN running, we can't access the prph before we reset
the NIC.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A few slave bus devices show better performance when we
reduce the size of the Tx A-MPDU.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Getting the BSS station vif is something that may be needed by other
parts of the code. So, instead of having an iterator specifically for
d3, change it into a generic one in utils.c. Additionally, add a
iwl_mvm_get_bss_vif() function to make it easier to retrieving it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Before we get all the chain (ie. mac80211, cfg80211, nl80211 and
userspace) changed to support net-detect, we can use this debugfs
entry for easy testing and as a proof of concept.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The net-detect feature will require a scan offload to be started in
the same way it is done now for scheduled scan. Spin a new function
off of the sched_scan_start op code for reuse. Additionally,
restructure the function a bit for more readability.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of checking if we are associated when suspending with wowlan
enabled in the interface iterator, allow it to return an unassociated
vif and move the check to the main suspend function. This will be
needed by netdetect, since it should also work when we are not
associated but the vif is active.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Take the WoWLAN handling code out of the main suspend function,
dividing it into three parts: get_config (which is used before the
firmware is switched), switch_to_d3 (which handles the rebooting of
the hardware with the D3 firmware) and config (which configures the D3
firmware for WoWLAN operation). This is necessary to prepare for the
net-detect implementation, which will use only the switch_to_d3 part
of this flow.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
mac80211 will never call rate_control_tx_status with a NULL
pointer for sta. Remove the superfluous check. This check
misled smatch.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The current TLC isn't optimized for low latency and some devices
have issues with MIMO. This kind of combo creates latency issues.
Allow to temporarily disable MIMO for tests in order to solve
the latency issues without the added complexity of MIMO.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_poll_bit may return a strictly positive value when the
poll doesn't match on the first try.
This was caught when WoWLAN started failing upon resume
even if the poll_bit actually succeeded.
Also change a wrong print. If we reach the end of
iwl_pcie_prepare_card_hw, it means that we couldn't
get the devices.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When mac80211 wants to ensure that a frame is sent, it calls
the flush() callback. Until now, iwldvm implemented this by
waiting that all the frames are sent (ACKed or timeout).
In case of weak signal, this can take a significant amount
of time, delaying the next connection (in case of roaming).
Many users have reported that the flush would take too long
leading to the following error messages to be printed:
iwlwifi 0000:03:00.0: fail to flush all tx fifo queues Q 2
iwlwifi 0000:03:00.0: Current SW read_ptr 161 write_ptr 201
iwl data: 00000000: 00 00 00 00 00 00 00 00 fe ff 01 00 00 00 00 00
[snip]
iwlwifi 0000:03:00.0: FH TRBs(0) = 0x00000000
[snip]
iwlwifi 0000:03:00.0: Q 0 is active and mapped to fifo 3 ra_tid 0x0000 [9,9]
[snip]
Instead of waiting for these packets, simply drop them. This
significantly improves the responsiveness of the network.
Note that all the queues are flushed, but the VO one. This
is not typically used by the applications and it likely
contains management frames that are useful for connection
or roaming.
This bug is tracked here:
https://bugzilla.kernel.org/show_bug.cgi?id=56581
But it is duplicated in distributions' trackers.
A simple search in Ubuntu's database led to these bugs:
https://bugs.launchpad.net/ubuntu/+source/linux-firmware/+bug/1270808https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1305406https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1356236https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1360597https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1361809
Cc: <stable@vger.kernel.org>
Depends-on: 77be2c54c5 ("mac80211: add vif to flush call")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Don't add the time event to the list. We added it several
times the same time event, which leads to an infinite loop
when walking the list.
Since we (currently) don't support more than one ROC for STA
vif at a time, enforce this and don't add the time event
to any list.
We were also missing the locking of the mutex which led to
a lockdep splat - fix that.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The tx power should be limited from many reasons.
currently, setting the tx power is available by the mvm only for
station interface. Adding the tx power condition to
bss_info_changed_ap_ibss make it available also for AP.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
I changed the string but forgot to update the fix also to
MODULE_FIRMWARE().
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The LTR is the handshake between the device and the root
complex about the latency allowed when the bus exits power
save. This configuration was missing and this led to high
latency in the link power up. The end user could experience
high latency in the network because of this.
Cc: <stable@vger.kernel.org> [3.10+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Channel switch with multiple channel contexts should now work fine.
Remove check that disallows switches when multiple contexts are in
use.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move iwl_mvm_max_scan_ie_len function to scan.c and fix the
implementation to conform with the LMAC scan API.
Since the correct implementation would leave us with unacceptably
tiny probes, add a workaround which returns a larger value.
In current implementation it's possible that unified_scan_lmac and
unified_sched_scan_lmac would return -ENOBUFS.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of traffic on multiple TIDs where one is aggregated
and the other is not RS would toggle between considering
traffic vs. the station as aggregated and not aggregated.
Instead consider the sta state as aggregated as long as
there's at least one TID aggregated.
This limitation is because the rates table is kept per
station and not per TID.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently BA notifications which don't reclaim any frames
would not cause the RS to be called as no skbs are passed
to mac80211. This is not optimal as RS can benefit from the
statistics of sent vs. acked of such a BA. This can improve the
reaction time of the RS algorithm. Also, an upcoming change in
the firmware would cause BA timeout to be reported as a BA notif
with 0 acked so this change is required for that as well.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 8000 HW series also includes the revision in the FW
name.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Align the trans->hw_rev variable format with previous series
format.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This is a tradeoff between enabling better throughput for
bursty traffic and low latency. The number 6 was found to be
a good tradeoff for the Miracast use case which is the
major use case for low latency.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Enable RS to get updated directly via iwl_mvm_rs_tx_status
which will be called by the driver and not via mac80211
rate control. This is required for a following patch to
report on BAs which do not cause the BA window to progress.
Also this is a first step in decoupling rs from the
mac80211 rate control.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Improve the initial tx rate and antenna selection to be based on
the rssi of the last rx. This avoids starting at the lowest legacy
rate always and requiring more tx traffic to "climb" up the rates.
Since this option might cause trouble in certain setups, allow to
disable it by default.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In the past when schedule scan was started while connected on one of
interfaces FW crashes were observed. In the newest FW this issue is
solved, so remove limitaion after examining corresponding TLV flag.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When read, this new debugfs entry requests the current temperature
from the firmware and outputs it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The scheduler is a HW sub-block that directs the work of the Flow
Handler by issuing requests for frame transfers, specifying source
and destination. Its primary function is to allocate flows into the
TX FIFOs based upon a pre-determined mapping.
The driver has some responsibilities to the scheduler, namely
initialising and maintaining the hardware registers. This is
currently done by directly accessing them, which can cause races
with the firmware also accessing the registers.
To address this problem, change the driver to no longer directly
access the registers but go through the firmware for this if the
firmware has support for DQA and thus the new command.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Set RRM_ENABLED (bit 6) flag in scan commands. When this flag is set
the fw will add WFA vendor-specific TPC report and DS parameter set
IEs into probe requests.
This bit is set for SCAN_OFFLOAD_REQUEST_CMD(0x51).
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add a ucode capability flag for support of Quiet Period (part of RRM).
If this flag is set, advertise device support.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Introduce new tx command flag (TX_CMD_FLG_WRITE_TX_POWER) which requests the
fw to update the tx power value at some constant offset.
Set this flag when transmitting either TPC report or Link measurement report
action frames.
In addition, introduce new tlv which indicates whether the fw supports power
insertion (IWL_UCODE_TLV_CAPA_TXPOWER_INSERTION_SUPPORT) and publish the
corresponding nl80211 feature.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Since tx skbs are not modified by the driver, let mac80211 know the
driver can handle cloned skbs.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed.
-----BEGIN PGP SIGNATURE-----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=OPIp
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-john-2014-09-12' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg <johannes@sipsolutions.net> says:
"This time, I have some rate minstrel improvements, support for a very
small feature from CCX that Steinar reverse-engineered, dynamic ACK
timeout support, a number of changes for TDLS, early support for radio
resource measurement and many fixes. Also, I'm changing a number of
places to clear key memory when it's freed and Intel claims copyright
for code they developed."
Conflicts:
net/mac80211/iface.c
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time event used for CSA GO will also be used by CSA client.
Rename the symbols to something more generic and aligned with the
firmware code.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
