Pull networking fixes from David Miller:
1) Use netif_rx_ni() when necessary in batman-adv stack, from Jussi
Kivilinna.
2) Fix loss of RTT samples in rxrpc, from David Howells.
3) Memory leak in hns_nic_dev_probe(), from Dignhao Liu.
4) ravb module cannot be unloaded, fix from Yuusuke Ashizuka.
5) We disable BH for too lokng in sctp_get_port_local(), add a
cond_resched() here as well, from Xin Long.
6) Fix memory leak in st95hf_in_send_cmd, from Dinghao Liu.
7) Out of bound access in bpf_raw_tp_link_fill_link_info(), from
Yonghong Song.
8) Missing of_node_put() in mt7530 DSA driver, from Sumera
Priyadarsini.
9) Fix crash in bnxt_fw_reset_task(), from Michael Chan.
10) Fix geneve tunnel checksumming bug in hns3, from Yi Li.
11) Memory leak in rxkad_verify_response, from Dinghao Liu.
12) In tipc, don't use smp_processor_id() in preemptible context. From
Tuong Lien.
13) Fix signedness issue in mlx4 memory allocation, from Shung-Hsi Yu.
14) Missing clk_disable_prepare() in gemini driver, from Dan Carpenter.
15) Fix ABI mismatch between driver and firmware in nfp, from Louis
Peens.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (110 commits)
net/smc: fix sock refcounting in case of termination
net/smc: reset sndbuf_desc if freed
net/smc: set rx_off for SMCR explicitly
net/smc: fix toleration of fake add_link messages
tg3: Fix soft lockup when tg3_reset_task() fails.
doc: net: dsa: Fix typo in config code sample
net: dp83867: Fix WoL SecureOn password
nfp: flower: fix ABI mismatch between driver and firmware
tipc: fix shutdown() of connectionless socket
ipv6: Fix sysctl max for fib_multipath_hash_policy
drivers/net/wan/hdlc: Change the default of hard_header_len to 0
net: gemini: Fix another missing clk_disable_unprepare() in probe
net: bcmgenet: fix mask check in bcmgenet_validate_flow()
amd-xgbe: Add support for new port mode
net: usb: dm9601: Add USB ID of Keenetic Plus DSL
vhost: fix typo in error message
net: ethernet: mlx4: Fix memory allocation in mlx4_buddy_init()
pktgen: fix error message with wrong function name
net: ethernet: ti: am65-cpsw: fix rmii 100Mbit link mode
cxgb4: fix thermal zone device registration
...
When an ISM device is removed, all its linkgroups are terminated,
i.e. all the corresponding connections are killed.
Connection killing invokes smc_close_active_abort(), which decreases
the sock refcount for certain states to simulate passive closing.
And it cancels the close worker and has to give up the sock lock for
this timeframe. This opens the door for a passive close worker or a
socket close to run in between. In this case smc_close_active_abort() and
passive close worker resp. smc_release() might do a sock_put for passive
closing. This causes:
[ 1323.315943] refcount_t: underflow; use-after-free.
[ 1323.316055] WARNING: CPU: 3 PID: 54469 at lib/refcount.c:28 refcount_warn_saturate+0xe8/0x130
[ 1323.316069] Kernel panic - not syncing: panic_on_warn set ...
[ 1323.316084] CPU: 3 PID: 54469 Comm: uperf Not tainted 5.9.0-20200826.rc2.git0.46328853ed20.300.fc32.s390x+debug #1
[ 1323.316096] Hardware name: IBM 2964 NC9 702 (z/VM 6.4.0)
[ 1323.316108] Call Trace:
[ 1323.316125] [<00000000c0d4aae8>] show_stack+0x90/0xf8
[ 1323.316143] [<00000000c15989b0>] dump_stack+0xa8/0xe8
[ 1323.316158] [<00000000c0d8344e>] panic+0x11e/0x288
[ 1323.316173] [<00000000c0d83144>] __warn+0xac/0x158
[ 1323.316187] [<00000000c1597a7a>] report_bug+0xb2/0x130
[ 1323.316201] [<00000000c0d36424>] monitor_event_exception+0x44/0xc0
[ 1323.316219] [<00000000c195c716>] pgm_check_handler+0x1da/0x238
[ 1323.316234] [<00000000c151844c>] refcount_warn_saturate+0xec/0x130
[ 1323.316280] ([<00000000c1518448>] refcount_warn_saturate+0xe8/0x130)
[ 1323.316310] [<000003ff801f2e2a>] smc_release+0x192/0x1c8 [smc]
[ 1323.316323] [<00000000c169f1fa>] __sock_release+0x5a/0xe0
[ 1323.316334] [<00000000c169f2ac>] sock_close+0x2c/0x40
[ 1323.316350] [<00000000c1086de0>] __fput+0xb8/0x278
[ 1323.316362] [<00000000c0db1e0e>] task_work_run+0x76/0xb8
[ 1323.316393] [<00000000c0d8ab84>] do_exit+0x26c/0x520
[ 1323.316408] [<00000000c0d8af08>] do_group_exit+0x48/0xc0
[ 1323.316421] [<00000000c0d8afa8>] __s390x_sys_exit_group+0x28/0x38
[ 1323.316433] [<00000000c195c32c>] system_call+0xe0/0x2b4
[ 1323.316446] 1 lock held by uperf/54469:
[ 1323.316456] #0: 0000000044125e60 (&sb->s_type->i_mutex_key#9){+.+.}-{3:3}, at: __sock_release+0x44/0xe0
The patch rechecks sock state in smc_close_active_abort() after
smc_close_cancel_work() to avoid duplicate decrease of sock
refcount for the same purpose.
Fixes: 611b63a127 ("net/smc: cancel tx worker in case of socket aborts")
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMC tries to make use of SMCD first. If a problem shows up,
it tries to switch to SMCR. If the SMCD initializing problem shows
up after the SMCD connection has already been initialized, field
rx_off keeps the wrong SMCD value for SMCR, which results in corrupted
data at the receiver.
This patch adds an explicit (re-)setting of field rx_off to zero if the
connection uses SMCR.
Fixes: be244f28d2 ("net/smc: add SMC-D support in data transfer")
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Older SMCR implementations had no link failover support and used one
link only. Because the handshake protocol requires to try the
establishment of a second link the old code sent a fake add_link message
and declined any server response afterwards.
The current code supports multiple links and inspects the received fake
add_link message more closely. To tolerate the fake add_link messages
smc_llc_is_local_add_link() needs an improved check of the message to
be able to separate between locally enqueued and fake add_link messages.
And smc_llc_cli_add_link() needs to check if the provided qp_mtu size is
invalid and reject the add_link request in that case.
Fixes: c48254fa48 ("net/smc: move add link processing for new device into llc layer")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__smc_diag_dump() is potentially copying uninitialized kernel stack memory
into socket buffers, since the compiler may leave a 4-byte hole near the
beginning of `struct smcd_diag_dmbinfo`. Fix it by initializing `dinfo`
with memset().
Fixes: 4b1b7d3b30 ("net/smc: add SMC-D diag support")
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the maximum dmb buffer limit for an ism device is reached no more
dmb buffers can be registered. When this happens the reason code is set
to SMC_CLC_DECL_MEM indicating out-of-memory. This is the same reason
code that is used when no memory could be allocated for the new dmb
buffer.
This is confusing for users when they see this error but there is more
memory available. To solve this set a separate new reason code when the
maximum dmb limit exceeded.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework the remaining setsockopt code to pass a sockptr_t instead of a
plain user pointer. This removes the last remaining set_fs(KERNEL_DS)
outside of architecture specific code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org> [ieee802154]
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a current limit of 1920 registered dmb buffers per ISM device
for smc-d. One link group can contain 255 connections, each connection
is using one dmb buffer. When the connection is closed then the
registered buffer is held in a queue and is reused by the next
connection. When a link group is 'full' then another link group is
created and uses an own buffer pool. The link groups are added to a
list using list_add() which puts a new link group to the first position
in the list.
In the situation that many connections are opened (>1920) and a few of
them stay open while others are closed quickly we end up with at least 8
link groups. For a new connection a matching link group is looked up,
iterating over the list of link groups. The trailing 7 link groups
all have registered dmb buffers which could be reused, while the first
link group has only a few dmb buffers and then hit the 1920 limit.
Because the first link group is not full (255 connection limit not
reached) it is chosen and finally the connection falls back to TCP
because there is no dmb buffer available in this link group.
There are multiple ways to fix that: using list_add_tail() allows
to scan older link groups first for free buffers which ensures that
buffers are reused first. This fixes the problem for smc-r link groups
as well. For smc-d there is an even better way to address this problem
because smc-d does not have the 255 connections per link group limit.
So fix the problem for smc-d by allowing large link groups.
Fixes: c6ba7c9ba4 ("net/smc: add base infrastructure for SMC-D and ISM")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To get a send slot smc_wr_tx_get_free_slot() is called, which might
wait for a free slot. When smc_wr_tx_get_free_slot() returns there is a
check if the connection was killed in the meantime. In that case don't
only return an error, but also put back the free slot.
Fixes: b290098092 ("net/smc: cancel send and receive for terminated socket")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just check for a NULL method instead of wiring up
sock_no_{get,set}sockopt.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a listen socket is closed then all non-accepted sockets in its
accept queue are to be released. Inside __smc_release() the helper
smc_restore_fallback_changes() restores the changes done to the socket
without to check if the clcsocket has a file set. This can result in
a crash. Fix this by checking the file pointer first.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f536dffc0b ("net/smc: fix closing of fallback SMC sockets")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two buffers are allocated for each SMC connection. Each buffer is
added to a buffer list after creation. When the second buffer
allocation fails, the first buffer is freed but not deleted from
the list. This might result in crashes when another connection picks
up the freed buffer later and starts to work with it.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 6511aad3f0 ("net/smc: change smc_buf_free function parameters")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma related ...sync_sg... functions check the link state before the
dma function is actually called. But the check in smc_link_usable()
allows links in ACTIVATING state which are not yet mapped to dma memory.
Under high load it may happen that the sync_sg functions are called for
such a link which results in an debug output like
DMA-API: mlx5_core 0002:00:00.0: device driver tries to sync
DMA memory it has not allocated [device address=0x0000000103370000]
[size=65536 bytes]
To fix that introduce a helper to check for the link state ACTIVE and
use it where appropriate. And move the link state update to ACTIVATING
to the end of smcr_link_init() when most initial setup is done.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: d854fcbfae ("net/smc: add new link state and related helpers")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As smc client the delete link requests are assigned to the flow when
_any_ flow is active. This may break other flows that do not expect
delete link requests during their handling. Fix that by assigning the
request only when an add link flow is active. With that fix the code
for smc client and smc server is the same, so remove the separate
handling.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 9ec6bf19ec ("net/smc: llc_del_link_work and use the LLC flow for delete link")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new ib device is up smc will send an add link invitation to the
peer if needed. This is currently done with rudimentary flow control.
Under high workload these add link invitations can disturb other llc
flows because they arrive unexpected. Fix this by integrating the
invitations into the normal llc event flow and handle them as a flow.
While at it, check for already assigned requests in the flow before
the new add link request is assigned.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1f90a05d9f ("net/smc: add smcr_port_add() and smcr_link_up() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be save from unexpected or late llc response messages check if the
arrived message fits to the current flow type and drop out-of-flow
messages. And drop it when there is already a response assigned to
the flow.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: ef79d439cd ("net/smc: process llc responses in tasklet context")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before an smc ib device is used the first time for an smc link it is
lazily initialized. When there are 2 active link groups and a new ib
device is brought online then it might happen that 2 link creations run
in parallel and enter smc_ib_setup_per_ibdev(). Both allocate new send
and receive completion queues on the device, but only one set of them
keeps assigned and the other leaks.
Fix that by protecting the setup and cleanup code using a mutex.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f3c1deddb2 ("net/smc: separate function for link initialization")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new rdma connections the SMC server assigns the link and sends the
link data in the clc accept message. To match the correct link use not
only the qp_num but also the gid and the mac of the links. If there are
equal qp_nums for different links the wrong link would be chosen.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 0fb0b02bd6 ("net/smc: adapt SMC client code to use the LLC flow")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a link-down condition we notify the SMC server and expect that the
server will finally trigger the link clear processing on the client
side. This could fail when anything along this notification path goes
wrong. Clear the link as part of SMC client link-down processing to
prevent dangling links.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 541afa10c1 ("net/smc: add smcr_port_err() and smcr_link_down() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A delete link could arrive during confirm link processing. Handle this
situation directly in smc_llc_srv_conf_link() rather than using the
logic in smc_llc_wait() to avoid the unexpected message handling there.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1551c95b61 ("net/smc: final part of add link processing as SMC server")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CLC proposal messages of future SMCD versions could be larger than SMCD
V1 CLC proposal messages.
To enable toleration in SMC V1 the receival of CLC proposal messages
is adapted:
* accept larger length values in CLC proposal
* check trailing eye catcher for incoming CLC proposal with V1 length only
* receive the whole CLC proposal even in cases it does not fit into the
V1 buffer
Fixes: e7b7a64a84 ("smc: support variable CLC proposal messages")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The similar smc_ib_devices spinlock has been converted to a mutex.
Protecting the smcd_dev_list by a mutex is possible as well. This
patch converts the smcd_dev_list spinlock to a mutex.
Fixes: c6ba7c9ba4 ("net/smc: add base infrastructure for SMC-D and ISM")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tests showed this BUG:
[572555.252867] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:935
[572555.252876] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 131031, name: smcapp
[572555.252879] INFO: lockdep is turned off.
[572555.252883] CPU: 1 PID: 131031 Comm: smcapp Tainted: G O 5.7.0-rc3uschi+ #356
[572555.252885] Hardware name: IBM 3906 M03 703 (LPAR)
[572555.252887] Call Trace:
[572555.252896] [<00000000ac364554>] show_stack+0x94/0xe8
[572555.252901] [<00000000aca1f400>] dump_stack+0xa0/0xe0
[572555.252906] [<00000000ac3c8c10>] ___might_sleep+0x260/0x280
[572555.252910] [<00000000acdc0c98>] __mutex_lock+0x48/0x940
[572555.252912] [<00000000acdc15c2>] mutex_lock_nested+0x32/0x40
[572555.252975] [<000003ff801762d0>] mlx5_lag_get_roce_netdev+0x30/0xc0 [mlx5_core]
[572555.252996] [<000003ff801fb3aa>] mlx5_ib_get_netdev+0x3a/0xe0 [mlx5_ib]
[572555.253007] [<000003ff80063848>] smc_pnet_find_roce_resource+0x1d8/0x310 [smc]
[572555.253011] [<000003ff800602f0>] __smc_connect+0x1f0/0x3e0 [smc]
[572555.253015] [<000003ff80060634>] smc_connect+0x154/0x190 [smc]
[572555.253022] [<00000000acbed8d4>] __sys_connect+0x94/0xd0
[572555.253025] [<00000000acbef620>] __s390x_sys_socketcall+0x170/0x360
[572555.253028] [<00000000acdc6800>] system_call+0x298/0x2b8
[572555.253030] INFO: lockdep is turned off.
Function smc_pnet_find_rdma_dev() might be called from
smc_pnet_find_roce_resource(). It holds the smc_ib_devices list
spinlock while calling infiniband op get_netdev(). At least for mlx5
the get_netdev operation wants mutex serialization, which conflicts
with the smc_ib_devices spinlock.
This patch switches the smc_ib_devices spinlock into a mutex to
allow sleeping when calling get_netdev().
Fixes: a4cf0443c4 ("smc: introduce SMC as an IB-client")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wait for pending sends only when smc_switch_conns() found a link to move
the connections to. Do not wait during link freeing, this can lead to
permanent hang situations. And refuse to provide a new tx slot on an
unusable link.
Fixes: c6f02ebeea ("net/smc: switch connections to alternate link")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There might be races in scenarios where both SMC link groups are on the
same system. Prevent that by creating separate wait queues for LLC flows
and messages. Switch to non-interruptable versions of wait_event() and
wake_up() for the llc flow waiter to make sure the waiters get control
sequentially. Fine tune the llc_flow_lock to include the assignment of
the message. Write to system log when an unexpected message was
dropped. And remove an extra indirection and use the existing local
variable lgr in smc_llc_enqueue().
Fixes: 555da9af82 ("net/smc: add event-based llc_flow framework")
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
A few large, long discussed works this time. The RNBD block driver has
been posted for nearly two years now, and the removal of FMR has been a
recurring discussion theme for a long time. The usual smattering of
features and bug fixes.
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and a
mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block RDMA
device specific to ionos's cloud environment. It brings strong multipath
and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs and
drivers. FRWR should be preferred for at least a decade now.
-----BEGIN PGP SIGNATURE-----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=9zTe
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma
Pull rdma updates from Jason Gunthorpe:
"A more active cycle than most of the recent past, with a few large,
long discussed works this time.
The RNBD block driver has been posted for nearly two years now, and
flowing through RDMA due to it also introducing a new ULP.
The removal of FMR has been a recurring discussion theme for a long
time.
And the usual smattering of features and bug fixes.
Summary:
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and
a mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block
RDMA device specific to ionos's cloud environment. It brings strong
multipath and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple
async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs
and drivers. FRWR should be preferred for at least a decade now"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (247 commits)
RDMA/cm: Spurious WARNING triggered in cm_destroy_id()
RDMA/mlx5: Return ECE DC support
RDMA/mlx5: Don't rely on FW to set zeros in ECE response
RDMA/mlx5: Return an error if copy_to_user fails
IB/hfi1: Use free_netdev() in hfi1_netdev_free()
RDMA/hns: Uninitialized variable in modify_qp_init_to_rtr()
RDMA/core: Move and rename trace_cm_id_create()
IB/hfi1: Fix hfi1_netdev_rx_init() error handling
RDMA: Remove 'max_map_per_fmr'
RDMA: Remove 'max_fmr'
RDMA/core: Remove FMR device ops
RDMA/rdmavt: Remove FMR memory registration
RDMA/mthca: Remove FMR support for memory registration
RDMA/mlx4: Remove FMR support for memory registration
RDMA/i40iw: Remove FMR leftovers
RDMA/bnxt_re: Remove FMR leftovers
RDMA/mlx5: Remove FMR leftovers
RDMA/core: Remove FMR pool API
RDMA/rds: Remove FMR support for memory registration
RDMA/srp: Remove support for FMR memory registration
...
Pull networking updates from David Miller:
1) Allow setting bluetooth L2CAP modes via socket option, from Luiz
Augusto von Dentz.
2) Add GSO partial support to igc, from Sasha Neftin.
3) Several cleanups and improvements to r8169 from Heiner Kallweit.
4) Add IF_OPER_TESTING link state and use it when ethtool triggers a
device self-test. From Andrew Lunn.
5) Start moving away from custom driver versions, use the globally
defined kernel version instead, from Leon Romanovsky.
6) Support GRO vis gro_cells in DSA layer, from Alexander Lobakin.
7) Allow hard IRQ deferral during NAPI, from Eric Dumazet.
8) Add sriov and vf support to hinic, from Luo bin.
9) Support Media Redundancy Protocol (MRP) in the bridging code, from
Horatiu Vultur.
10) Support netmap in the nft_nat code, from Pablo Neira Ayuso.
11) Allow UDPv6 encapsulation of ESP in the ipsec code, from Sabrina
Dubroca. Also add ipv6 support for espintcp.
12) Lots of ReST conversions of the networking documentation, from Mauro
Carvalho Chehab.
13) Support configuration of ethtool rxnfc flows in bcmgenet driver,
from Doug Berger.
14) Allow to dump cgroup id and filter by it in inet_diag code, from
Dmitry Yakunin.
15) Add infrastructure to export netlink attribute policies to
userspace, from Johannes Berg.
16) Several optimizations to sch_fq scheduler, from Eric Dumazet.
17) Fallback to the default qdisc if qdisc init fails because otherwise
a packet scheduler init failure will make a device inoperative. From
Jesper Dangaard Brouer.
18) Several RISCV bpf jit optimizations, from Luke Nelson.
19) Correct the return type of the ->ndo_start_xmit() method in several
drivers, it's netdev_tx_t but many drivers were using
'int'. From Yunjian Wang.
20) Add an ethtool interface for PHY master/slave config, from Oleksij
Rempel.
21) Add BPF iterators, from Yonghang Song.
22) Add cable test infrastructure, including ethool interfaces, from
Andrew Lunn. Marvell PHY driver is the first to support this
facility.
23) Remove zero-length arrays all over, from Gustavo A. R. Silva.
24) Calculate and maintain an explicit frame size in XDP, from Jesper
Dangaard Brouer.
25) Add CAP_BPF, from Alexei Starovoitov.
26) Support terse dumps in the packet scheduler, from Vlad Buslov.
27) Support XDP_TX bulking in dpaa2 driver, from Ioana Ciornei.
28) Add devm_register_netdev(), from Bartosz Golaszewski.
29) Minimize qdisc resets, from Cong Wang.
30) Get rid of kernel_getsockopt and kernel_setsockopt in order to
eliminate set_fs/get_fs calls. From Christoph Hellwig.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2517 commits)
selftests: net: ip_defrag: ignore EPERM
net_failover: fixed rollback in net_failover_open()
Revert "tipc: Fix potential tipc_aead refcnt leak in tipc_crypto_rcv"
Revert "tipc: Fix potential tipc_node refcnt leak in tipc_rcv"
vmxnet3: allow rx flow hash ops only when rss is enabled
hinic: add set_channels ethtool_ops support
selftests/bpf: Add a default $(CXX) value
tools/bpf: Don't use $(COMPILE.c)
bpf, selftests: Use bpf_probe_read_kernel
s390/bpf: Use bcr 0,%0 as tail call nop filler
s390/bpf: Maintain 8-byte stack alignment
selftests/bpf: Fix verifier test
selftests/bpf: Fix sample_cnt shared between two threads
bpf, selftests: Adapt cls_redirect to call csum_level helper
bpf: Add csum_level helper for fixing up csum levels
bpf: Fix up bpf_skb_adjust_room helper's skb csum setting
sfc: add missing annotation for efx_ef10_try_update_nic_stats_vf()
crypto/chtls: IPv6 support for inline TLS
Crypto/chcr: Fixes a coccinile check error
Crypto/chcr: Fixes compilations warnings
...
Pre-fetch send buffer for the CDC validation message before entering the
send_lock. Without that the send call might fail with -EBUSY because
there are no free buffers and waiting for buffers is not possible under
send_lock.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netlink policies are generally declared as const.
This is safer and prevents potential bugs.
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
net/smc/smc_llc.c: In function 'smc_llc_cli_conf_link':
net/smc/smc_llc.c:753:31: warning:
variable 'del_llc' set but not used [-Wunused-but-set-variable]
struct smc_llc_msg_del_link *del_llc;
^
net/smc/smc_llc.c: In function 'smc_llc_process_srv_delete_link':
net/smc/smc_llc.c:1311:33: warning:
variable 'del_llc_resp' set but not used [-Wunused-but-set-variable]
struct smc_llc_msg_del_link *del_llc_resp;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a client is added it isn't allowed to fail, but all the client's have
various failure paths within their add routines.
This creates the very fringe condition where the client was added, failed
during add and didn't set the client_data. The core code will then still
call other client_data centric ops like remove(), rename(), get_nl_info(),
and get_net_dev_by_params() with NULL client_data - which is confusing and
unexpected.
If the add() callback fails, then do not call any more client ops for the
device, even remove.
Remove all the now redundant checks for NULL client_data in ops callbacks.
Update all the add() callbacks to return error codes
appropriately. EOPNOTSUPP is used for cases where the ULP does not support
the ib_device - eg because it only works with IB.
Link: https://lore.kernel.org/r/20200421172440.387069-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Acked-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
commit bac6de7b63 ("net/smc: eliminate cursor read and write calls")
left behind this.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print to system log when SMC links are available or go down, link group
state changes or pnetids are applied to and removed from devices.
The log entries are triggered by either user configuration actions or
adapter activation/deactivation events and are not expected to happen
often. The entries help SMC users to keep track of the SMC link group
status and to detect when actions are needed (like to add replacements
for failed adapters).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During SMC-R link establishment the peers exchange the link_uid that
is used for debugging purposes. Save the peer link_uid in smc_link so it
can be retrieved by the smc_diag netlink interface.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link_uid of an SMC-R link is exchanged between SMC peers and its
value can be used for debugging purposes. Create a unique link_uid
during link initialization and use it in communication with SMC-R peers.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper smcr_lgr_link_deactivate_all() and eliminate duplicate code.
In smc_lgr_free(), clear the smc-r links before smc_lgr_free_bufs() is
called so buffers are already prepared for free. The usage of the soft
parameter in __smc_lgr_terminate() is no longer needed, smc_lgr_free()
can be called directly. smc_lgr_terminate_sched() and
smc_smcd_terminate() set lgr->freeing to indicate that the link group
will be freed soon to avoid unnecessary schedules of the free worker.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to set the reason code for the link group termination, and set
meaningful values before termination processing is triggered. This
reason code is sent to the peer in the final delete link message.
When the LLC request or response layer receives a message type that was
not handled, drop a warning and terminate the link group.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New connections must not be assigned to asymmetric links. Add asymmetric
link tagging using new link variable link_is_asym. The new helpers
smcr_lgr_set_type() and smcr_lgr_set_type_asym() are called to set the
state of the link group, and tag all links accordingly.
smcr_lgr_conn_assign_link() respects the link tagging and will not
assign new connections to links tagged as asymmetric link.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new connections, assign a link from the link group, using some
simple load balancing.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_llc_send_message_wait() which uses smc_wr_tx_send_wait() to send
an LLC message and waits for the message send to complete.
smc_llc_send_link_delete_all() calls the new function to send an
DELETE_LINK,ALL LLC message. The RFC states that the sender of this type
of message needs to wait for the completion event of the message
transmission and can terminate the link afterwards.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce smc_wr_tx_send_wait() to send an IB message and wait for the
tx completion event of the message. This makes sure that the message is
no longer in-flight when the function returns.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call smc_cdc_msg_validate() when a CDC message with the failover
validation bit enabled was received. Validate that the sequence number
sent with the message is one we already have received. If not, messages
were lost and the connection is terminated using a new abort_work.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a connection is switched to a new link then a link validation
message must be sent to the peer over the new link, containing the
sequence number of the last CDC message that was sent over the old link.
The peer will validate if this sequence number is the same or lower then
the number he received, and abort the connection if messages were lost.
Add smcr_cdc_msg_send_validation() to send the message validation
message and call it when a connection was switched in
smc_switch_cursor().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add smc_switch_conns() to switch all connections from a link that is
going down. Find an other link to switch the connections to, and
switch each connection to the new link. smc_switch_cursor() updates the
cursors of a connection to the state of the last successfully sent CDC
message. When there is no link to switch to, terminate the link group.
Call smc_switch_conns() when a link is going down.
And with the possibility that links of connections can switch adapt CDC
and TX functions to detect and handle link switches.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
