Commit c9a5eccac1 ("kvm/eventfd: add arch-specific set_irq",
2015-10-16) added the possibility for architecture-specific code
to handle the generation of virtual interrupts in atomic context
where possible, without having to schedule a work function.
Since we can easily generate virtual interrupts on XICS without
having to do anything worse than take a spinlock, we define a
kvm_arch_set_irq_inatomic() for XICS. We also remove kvm_set_msi()
since it is not used any more.
The one slightly tricky thing is that with the new interface, we
don't get told whether the interrupt is an MSI (or other edge
sensitive interrupt) vs. level-sensitive. The difference as far
as interrupt generation is concerned is that for LSIs we have to
set the asserted flag so it will continue to fire until it is
explicitly cleared.
In fact the XICS code gets told which interrupts are LSIs by userspace
when it configures the interrupt via the KVM_DEV_XICS_GRP_SOURCES
attribute group on the XICS device. To store this information, we add
a new "lsi" field to struct ics_irq_state. With that we can also do a
better job of returning accurate values when reading the attribute
group.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add two counters to count how often we generate real-mode ICS resend
and reject events. The counters provide some performance statistics
that could be used in the future to consider if the real mode functions
need further optimizing. The counters are displayed as part of IPC and
ICP state provided by /sys/debug/kernel/powerpc/kvm* for each VM.
Also added two counters that count (approximately) how many times we
don't find an ICP or ICS we're looking for. These are not currently
exposed through sysfs, but can be useful when debugging crashes.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Replaces the ICS mutex lock with a spin lock since we will be porting
these routines to real mode. Note that we need to disable interrupts
before we take the lock in anticipation of the fact that on the guest
side, we are running in the context of a hard irq and interrupts are
disabled (EE bit off) when the lock is acquired. Again, because we
will be acquiring the lock in hypervisor real mode, we need to use
an arch_spinlock_t instead of a normal spinlock here as we want to
avoid running any lockdep code (which may not be safe to execute in
real mode).
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add counters to track number of times we switch from guest real mode
to host virtual mode during an interrupt-related hyper call because the
hypercall requires actions that cannot be completed in real mode. This
will help when making optimizations that reduce guest-host transitions.
It is safe to use an ordinary increment rather than an atomic operation
because there is one ICP per virtual CPU and kvmppc_xics_rm_complete()
only works on the ICP for the current VCPU.
The counters are displayed as part of IPC and ICP state provided by
/sys/debug/kernel/powerpc/kvm* for each VM.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes some inaccuracies in the state machine for the virtualized
ICP when implementing the H_IPI hcall (Set_MFFR and related states):
1. The old code wipes out any pending interrupts when the new MFRR is
more favored than the CPPR but less favored than a pending
interrupt (by always modifying xisr and the pending_pri). This can
cause us to lose a pending external interrupt.
The correct code here is to only modify the pending_pri and xisr in
the ICP if the MFRR is equal to or more favored than the current
pending pri (since in this case, it is guaranteed that that there
cannot be a pending external interrupt). The code changes are
required in both kvmppc_rm_h_ipi and kvmppc_h_ipi.
2. Again, in both kvmppc_rm_h_ipi and kvmppc_h_ipi, there is a check
for whether MFRR is being made less favored AND further if new MFFR
is also less favored than the current CPPR, we check for any
resends pending in the ICP. These checks look like they are
designed to cover the case where if the MFRR is being made less
favored, we opportunistically trigger a resend of any interrupts
that had been previously rejected. Although, this is not a state
described by PAPR, this is an action we actually need to do
especially if the CPPR is already at 0xFF. Because in this case,
the resend bit will stay on until another ICP state change which
may be a long time coming and the interrupt stays pending until
then. The current code which checks for MFRR < CPPR is broken when
CPPR is 0xFF since it will not get triggered in that case.
Ideally, we would want to do a resend only if
prio(pending_interrupt) < mfrr && prio(pending_interrupt) < cppr
where pending interrupt is the one that was rejected. But we don't
have the priority of the pending interrupt state saved, so we
simply trigger a resend whenever the MFRR is made less favored.
3. In kvmppc_rm_h_ipi, where we save state to pass resends to the
virtual mode, we also need to save the ICP whose need_resend we
reset since this does not need to be my ICP (vcpu->arch.icp) as is
incorrectly assumed by the current code. A new field rm_resend_icp
is added to the kvmppc_icp structure for this purpose.
Signed-off-by: Suresh Warrier <warrier@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This makes it possible to use IRQFDs on platforms that use the XICS
interrupt controller. To do this we implement kvm_irq_map_gsi() and
kvm_irq_map_chip_pin() in book3s_xics.c, so as to provide a 1-1 mapping
between global interrupt numbers and XICS interrupt source numbers.
For now, all interrupts are mapped as "IRQCHIP" interrupts, and no
MSI support is provided.
This means that kvm_set_irq can now get called with level == 0 or 1
as well as the powerpc-specific values KVM_INTERRUPT_SET,
KVM_INTERRUPT_UNSET and KVM_INTERRUPT_SET_LEVEL. We change
ics_deliver_irq() to accept all those values, and remove its
report_status argument, as it is always false, given that we don't
support KVM_IRQ_LINE_STATUS.
This also adds support for interrupt ack notifiers to the XICS code
so that the IRQFD resampler functionality can be supported.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This adds the API for userspace to instantiate an XICS device in a VM
and connect VCPUs to it. The API consists of a new device type for
the KVM_CREATE_DEVICE ioctl, a new capability KVM_CAP_IRQ_XICS, which
functions similarly to KVM_CAP_IRQ_MPIC, and the KVM_IRQ_LINE ioctl,
which is used to assert and deassert interrupt inputs of the XICS.
The XICS device has one attribute group, KVM_DEV_XICS_GRP_SOURCES.
Each attribute within this group corresponds to the state of one
interrupt source. The attribute number is the same as the interrupt
source number.
This does not support irq routing or irqfd yet.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds support for the ibm,int-on and ibm,int-off RTAS calls to the
in-kernel XICS emulation and corrects the handling of the saved
priority by the ibm,set-xive RTAS call. With this, ibm,int-off sets
the specified interrupt's priority in its saved_priority field and
sets the priority to 0xff (the least favoured value). ibm,int-on
restores the saved_priority to the priority field, and ibm,set-xive
sets both the priority and the saved_priority to the specified
priority value.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds an implementation of the XICS hypercalls in real mode for HV
KVM, which allows us to avoid exiting the guest MMU context on all
threads for a variety of operations such as fetching a pending
interrupt, EOI of messages, IPIs, etc.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This adds in-kernel emulation of the XICS (eXternal Interrupt
Controller Specification) interrupt controller specified by PAPR, for
both HV and PR KVM guests.
The XICS emulation supports up to 1048560 interrupt sources.
Interrupt source numbers below 16 are reserved; 0 is used to mean no
interrupt and 2 is used for IPIs. Internally these are represented in
blocks of 1024, called ICS (interrupt controller source) entities, but
that is not visible to userspace.
Each vcpu gets one ICP (interrupt controller presentation) entity,
used to store the per-vcpu state such as vcpu priority, pending
interrupt state, IPI request, etc.
This does not include any API or any way to connect vcpus to their
ICP state; that will be added in later patches.
This is based on an initial implementation by Michael Ellerman
<michael@ellerman.id.au> reworked by Benjamin Herrenschmidt and
Paul Mackerras.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
[agraf: fix typo, add dependency on !KVM_MPIC]
Signed-off-by: Alexander Graf <agraf@suse.de>