Might be able to merge this back in at some point, but we're seeing bugs
with ADPA based detection, so keep it separate for now with explicit
hotplug trigger usage.
v2: drop superfluous debug message
v3: comment forced detection, need to debug (Eugeni)
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VGA hotplug detection "works" by measuring the resistance across
certain pins. A lot of kvm switches fumble this and wire up cheap
resistors with the wrong resistance or don't bother at all.
To accomodate these, also try to detect a connected monitor by trying
to grab the edid. Contrary to !HAS_HOTPLUG platforms we don't bother
with an actual load-detection cycle when the output is life - that
would be actual work to implement because things moved around. This is
the big difference to Chris Wilson's original approach:
commit 9e612a008f
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu May 31 13:08:53 2012 +0100
drm/i915/crt: Do not rely upon the HPD presence pin
This blew up on Linus' machine because it errornously detected a vga
screen (without and edid and hence only the default modes), leading to
it's prompt removal:
commit 8f53369b75
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Fri Jun 8 14:53:06 2012 -0700
Revert "drm/i915/crt: Do not rely upon the HPD presence pin"
Some digging around in Bspec shows the reason why load detect doesn't work on
newer chips - the legacy VGA load detect bit isn't wired up any longer:
Public Snb Bspec, Vol3 Part1, 1.1.1 ST00 Input Status 0, bit4:
"RGB Comparator / Sense. This bit is here for compatibility and will
always return one. Monitor detection must be done be done through the
programming of registers in the MMIO space.
0 = Below threshold
1 = Above threshold"
v2: Add a comment in the code that load detect on hotplug capable
machines is broken and pimp the commit message with a quote of Bspec
to show why.
Reported-and-tested-by: Matthieu LAVIE <boiteamadmax@hotmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=50501
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Haswell, only one pipe can work in FDI mode, so this patch prevents
messing with wrong registers when FDI is being used by non-first pipe. And
to prevent this, we also specify that the VGA can only be used on pipe 0
for now in the crtc_mask value.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPpvY9AAoJEHm+PkMAQRiGpEoIAJgbu+Y8gITnBK/wh9O6zy3S
5jie5KK4YWdbJsvO58WbNr3CyVIwGIqQ2dUZLiU59aBVLarlGw8xor0MmW+cZwhp
6fBHaf0qDYAV0MZjD+mnnExOiCRyISa2lPmsfu9dAWywh5KGe6/oAP6/qcXIyok3
KZyl3qQf4ENpaZPHwZPXCEkUvtuyHgNiszN+QXEadA3s19Ot4VGe9A3VGw+GNrSm
JqFIq3acQAbKa5BYaqf7TQC02v2FI7//eqt6QHxTqbE6a7LGbTvLfX3HlJ2mnfqa
1R6QHhM4y4OZDHbaMT2raHZ8WuLXzhehJzhP8Co7AHFOKwVKOb5XbcUr2RrukMU=
=HkMd
-----END PGP SIGNATURE-----
Merge tag 'v3.4-rc6' into drm-intel-next
Conflicts:
drivers/gpu/drm/i915/intel_display.c
Ok, this is a fun story of git totally messing things up. There
/shouldn't/ be any conflict in here, because the fixes in -rc6 do only
touch functions that have not been changed in -next.
The offending commits in drm-next are 14415745b2..1fa611065 which
simply move a few functions from intel_display.c to intel_pm.c. The
problem seems to be that git diff gets completely confused:
$ git diff 14415745b2..1fa611065
is a nice mess in intel_display.c, and the diff leaks into totally
unrelated functions, whereas
$git diff --minimal 14415745b2..1fa611065
is exactly what we want.
Unfortunately there seems to be no way to teach similar smarts to the
merge diff and conflict generation code, because with the minimal diff
there really shouldn't be any conflicts. For added hilarity, every
time something in that area changes the + and - lines in the diff move
around like crazy, again resulting in new conflicts. So I fear this
mess will stay with us for a little longer (and might result in
another backmerge down the road).
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow we have a fast-path that tries to avoid going through
the load-detect code when the encode already has a crtc associated.
But this fails horribly when the crtc is off. The load detect pipe
itself manages this case well (and also does not forget to restore the
dpms state), so just rip out this special case.
The issue seems to go back all the way to the commit that originally
introduced load-detection on the vga output:
commit e4a5d54f92
Author: Ma Ling <ling.ma@intel.com>
Date: Tue May 26 11:31:00 2009 +0800
drm/i915: Add support for VGA load detection (pre-945).
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=43020
Reported-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the PCH split occurred, hw dropped support for separate hsync and
vsync disable in the VGA DAC. So add a PCH specific DPMS function that
just uses the port enable bit for controlling DPMS states.
Before this fix, when anything other than a full DPMS off occurred,
the VGA port would be left enabled and scanning out while all the other
heads would turn off as expected.
v2: duplicate encoder helper vtable into pch and gmch versions (Daniel)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=48491
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/intel_crt_dpms/gmch_crt_dpms as suggested by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And add informational dmesg output where it does not yet exist.
In case a quirk matches too much, this information is crucial for
debugging such a bug report.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of letting other modules directly access the ->gmbus array,
introduce intel_gmbus_get_adapter() for looking up an i2c_adapter
for a given gmbus port identifier. This will enable later refactoring
of the gmbus port list.
Note: Before requesting an adapter for a given gmbus port number, the
driver must first check its validity using i2c_intel_gmbus_is_port_valid().
If this check fails, a call to intel_gmbus_get_adapter() will WARN_ON and
return NULL. This is relevant for parts of the driver that read a port
from VBIOS, which might be improperly initialized and contain an invalid
port. In these cases, the driver must fall back to using a safer default
port.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
gen2 doesn't support it, so be a bit more paranoid and add a check to
ensure that we never ever set an unsupported interlaced bit.
Ensure that userspace can't set an interlaced mode by resetting
interlace_allowed for the crt on gen2. dvo and lvds are the only other
encoders that gen2 supports and these already disallow interlaced
modes.
Reviewed-by: Eugeni Dodonov <eugeni.dodonov@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the method used to override LVDS in intel_lvds and appears to be
an effective way to ensure that the driver does not enable VGA hotplug.
This is the same patch from 2.6.32 kernel in R12 but ported to 2.6.38,
will send upstream next.
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
BUG=chrome-os-partner:117
TEST=Check PORT_HOTPLUG_EN to see if hotplug interrupt is disabled.
Run the following command as root, specifically looking at bit 9:
mmio_read32 $[$(pci_read32 0 2 0 0x10) + 0x61110] = 0x00000000
Change-Id: Id8240f9fb31d058d8d79ee72f7b4615c43893f5a
Reviewed-on: http://gerrit.chromium.org/gerrit/1390
Reviewed-by: Olof Johansson <olofj@chromium.org>
Tested-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
Various issues involved with the space character were generating
warnings in the checkpatch.pl file. This patch removes most of those
warnings.
Signed-off-by: Akshay Joshi <me@akshayjoshi.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Rather than proceed on and silently return false by default, mention why
we rejected the presence of an EDID as implying the presence of a VGA
monitor. (The question arises whether there is a broken EDID which falsely
reports a digital connection when attached by VGA.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
Keep all the state required for undoing and restoring the previous pipe
configuration together in a single struct passed from
intel_get_load_detect_pipe() to intel_release_load_detect_pipe() rather
than stuffing them inside the common encoder structure.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
... and so remove the confusion as to whether to use the returned crtc
or intel_encoder->base.crtc with the subsequent load-detection. Even
though they were the same, the two instances of load-detection code
disagreed over which was the more correct.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Keith Packard <keithp@keithp.com>
This is a moral revert of 6ec3d0c0e9.
Following the fix to reset the GMBUS controller after a NAK, we finally
utilize the 0xa0 probe for a CRT connection. And discover that the code
is broken. Shock.
There are a number of issues, but following a key insight from Dave
Airlie, that 0xA0 is an invalid address on a 7-bit bus (though not if we
were to enable 10-bit addressing), and would look like the EDID port
0x50, it is possible to see where the confusion starts.
In short, a write to 0xA0 is accepted by the GMBUS controller which we
interpreted as meaning the existence of a connection (a slave on the
other end of the wire ACKing the write). That was false.
During testing with a broken GMBUS implementation, which never reset an
earlier NAK, this test always reported a NAK and so we proceeded on to
the next test.
Reported-and-tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=35904
Reported-and-tested-by: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32612
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Keith Packard <keithp@keithp.com>
We had some conversions over to the _PIPE macros, but didn't get
everything. So hide the per-pipe regs with an _ (still used in a few
places for legacy) and add a few _PIPE based macros, then make sure
everyone uses them.
[update: remove usage of non-existent no-op macro]
[update 2: keep modesetting suspend/resume code, update to new reg names]
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[ickle: stylistic cleanups for checkpatch and taste]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Upon resume, like after a cold boot, we need to forcibly probe the
analog connector and cannot rely on the hotplug status.
Based on a patch by Takashi Iwai.
Reported-by: Stefan Dirsch <sndirsch@suse.de>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=26952
Tested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Since Linux 2.6.36 the digital output on my system (855GME + DVI-I) is
not working any longer. The analog output is always activated
regardless of the type of monitor attached.
The culprit seems to be intel_crt_detect_ddc(), which returns true as
soon as an ACK from the EDID device is received. Obviously this
approach does not work with DVI-I where the analog and digital outputs
share a common DDC bus.
In a similar manner to the shared DDC wire, ala the "Mac Mini Hack", we
need an additional check to make sure that there really is an analog
device attached to the DDC.
Signed-off-by: David Müller <d.mueller@elsoft.ch>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Both IBX and CPT have an automatic hotplug detection mode which appears to work reliably enough
that we can dispense with the manual force hotplug trigger stuff. This means that
hotplug detection is as simple as reading the current hotplug register values.
The first time the hotplug detection is activated, the code synchronously waits for a hotplug
sequence in case the hardware hasn't bothered to do a detection cycle since being initialized.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We will use this structure in future patches to store CRT specific
information on the encoder.
Split out and tweaked from a patch by Keith Packard.
Signed-off-by: Keith Packard <keithp@kithp.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
After disabling the hotplug interrupts for VGA detection on Ironlake, be
sure to re-enable them again afterwards.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=30378
Signed-off-by: Yuanhan Liu <yuanhan.liu@intel.com>
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The BIOS writer's guide suggests that a VGA connection will ACK a write
to address 0xA0 and that this should be used before doing legacy
load-detection. Considering the extreme cost of load-detection,
performing an extra DDC seems a risk worth taking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Use the GMBUS interface rather than direct bit banging to grab the EDID
over DDC (and for other forms of auxiliary communication with external
display controllers). The hope is that this method will be much faster
and more reliable than bit banging for fetching EDIDs from buggy monitors
or through switches, though we still preserve the bit banging as a
fallback in case GMBUS fails.
Based on an original patch by Jesse Barnes.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
These are not fatal errors, so do not alarm the user by filling the
logs with *** ERROR ***. Especially as we know that g4x CRT detection
is a little sticky.
On the one hand the errors are valid since they are warning us of a
stall -- we poll the register whilst holding the mode lock so not even
the mouse will update. On the other hand, those stalls were already present
yet nobody complained.
Reported-by: Andi Kleen <andi@firstfloor.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=18332
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Later initialisation of the encoder often requires that
drm_encoder_init() has already been called, for instance, initialiasing
the DDC buses.
Yet another recent regression, as 819f3fb7 depended upon these fixes
which I missed when cherry-picking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
The SDVO proxy i2c adapter wants to be able to use information stored in
the encoder, so pass that through intel_i2c rather than iterate over all
known encoders every time.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
v2: Julien Cristau pointed out that @nondestructive results in
double-negatives and confusion when trying to interpret the parameter,
so use @force instead. Much easier to type as well. ;-)
And fix the miscompilation of vmgfx reported by Sedat Dilek.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Destructive load-detection is very expensive and due to failings
elsewhere can trigger system wide stalls of up to 600ms. A simple
first step to correcting this is not to invoke such an expensive
and destructive load-detection operation automatically.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=29536
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16265
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Currently we have a exact mapping of a connector onto an encoder for its
whole lifetime. Make this an explicit property of the structure and so
simplify the code.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[Patch is slightly larger than is strictly necessary to fixup
surrounding checkpatch.pl errors.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we don't flush the write then we can not be sure that the border
colour will have taken effect by the time we try to read it back.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Jesse's feedback from using the wait_for() macro was that the msleep
argument was that it was superfluous and made the macro more difficult
to use and to read. As the actually amount of time to sleep is not
critical, the crucial part is to sleep and let the processor schedule
something else whilst we wait for the event, replace the argument with a
hardcoded value.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Like on Sandybridge, disabling the DAC here when doing CRT load detect
avoids forever hangs waiting on the hardware.
test procedure on HP 2740p:
boot with no VGA plugged in, start X,
plug in VGA monitor (1280x1024)
chvt 3
machine hangs waiting forever.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Waiting for a hard coded 20ms isn't always enough to make sure a vblank
period has actually occurred, so add code to make sure we really have
passed through a vblank period (or that the pipe is off when disabling).
This prevents problems with mode setting and link training, and seems to
fix a bug like https://bugs.freedesktop.org/show_bug.cgi?id=29278, but
on an HP 8440p instead. Hopefully also fixes
https://bugs.freedesktop.org/show_bug.cgi?id=29141.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a new macro, wait_for, to simplify the act of waiting on a register
to change state. wait_for() takes three arguments, the condition to
inspect on every loop, the maximum amount of time to wait and whether to
yield the cpu for a length of time after each check.
v2: Upgrade failure messages to DRM_ERROR on the suggestion of
Eric Anholt. We do not expect to hit these conditions as they reflect
programming errors, so if we do we want to be notified.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Subclass intel_encoder to reduce the pointer dance through
intel_encoder->dev_priv.
10 files changed, 896 insertions(+), 997 deletions(-)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Commit 7a772c492f has two bugs which
made the hotplug problems on my laptop worse instead of better.
First, it did not, in fact, disable the CRT plug interrupt -- it
disabled all the other hotplug interrupts. It seems rather doubtful
that that bit of the patch fixed anything, so let's just remove it.
(If you want to add it back, you probably meant ~CRT_HOTPLUG_INT_EN.)
Second, on at least my GM45, setting CRT_HOTPLUG_ACTIVATION_PERIOD_64
and CRT_HOTPLUG_VOLTAGE_COMPARE_50 (when they were previously unset)
causes a hotplug interrupt about three seconds later. The old code
never restored PORT_HOTPLUG_EN so this could only happen once, but
they new code restores those registers. So just set those bits when
we set up the interrupt in the first place.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable the CRT plug interrupt while doing the force cycle, explicitly
clear any CRT interrupt we may have generated, and restore when done.
Should mitigate interrupt storms from hotplug detection.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This doesn't change the clock limits (minimums), i.e. it won't make it
output 720x576 PAL nor 720x480 NTSC, but it will work with modes like
1080i etc. (including GLX and textured Xvideo, not sure about the
overlay).
Tested on i915 + analog VGA, it would be worth checking if newer chips
(and which ones) still support interlaced mode.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Eric Anholt <eric@anholt.net>
After thinking it over a lot it made more sense for the core to deal with
the output polling especially so it can notify X.
v2: drop plans for fake connector - per Michel's comments - fix X patch sent to xorg-devel, add intel polled/hpd setting, add initial nouveau polled/hpd settings.
v3: add config lock take inside polling, add intel/nouveau poll init/fini calls
v4: config lock was a bit agressive, only needed around connector list reading.
otherwise it could re-enter.
glisse: discard drm_helper_hpd_irq_event
v3: Reviewed-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
To make CRT force detect reliable on Cougarpoint, we need to
disable DAC before force detect, and restore back when trigger
is completed.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cougarpoint is the new PCH for Sandybridge CPU. This one resolves the
chipset change for display pipeline compared to previous Ibexpeak PCH.
Sandybridge/Cougarpoint has different FDI training parameters, so this also
makes seperate FDI training functions for IBX and CPT. Other change includes
new transcoder DPLL select function to set which DPLL for transcoder to pick
up.
And with another new transcoder C introduced in Cougarpoint, each connector
has new transcoder select bits. This one adds that change to light up VGA.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
