One variant of the SX150X GPIO chip supports setting the pins in
open drain mode. This is currently available to set from platform
data, but completely unused in the kernel.
Activate the new .set_single_ended() callback so users can set
this up from e.g. device tree or board files using the new
GPIO descriptors.
As part of this, delete the platform data open drain setting
method.
Cc: Wei Chen <Wei.Chen@csr.com>
Cc: Peter Rosin <peda@axentia.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sx150x has some platform data definition in <linux/i2c/sx150x.h>
but this file is only included from the driver in the whole kernel
so move its contents into the driver.
Cc: Wei Chen <Wei.Chen@csr.com>
Cc: Peter Rosin <peda@axentia.se>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TPS65218 supports open drain mode on its three pins,
with one of them configurable also as push-pull. Use the
new .set_single_ended() callback to set this up properly
from the core, so the core actually see it can drive the
pin(s) as open drain, and does not attempt to emulate
open drain by switching the pin to an input.
Acked-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If GPIO hog configuration failed while adding OF based
gpiochip() then return the error instead of ignoring it.
This helps of properly handling the gpio driver dependency.
When adding the gpio hog nodes for NVIDIA's Tegra210 platforms,
the gpio_hogd() fails with EPROBE_DEFER because pinctrl is not
ready at this time and gpio_request() for Tegra GPIO driver
returns error. The error was not causing the Tegra GPIO driver
to fail as the error was getting ignored.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Benoit Parrot <bparrot@ti.com>
Cc: Alexandre Courbot <acourbot@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Galileo Gen2 board uses the PCAL9535 as the GPIO expansion,
it is different from PCA9535 and includes interrupt mask/status registers,
The current driver does not support the interrupt registers configuration,
it causes some gpio pins cannot trigger interrupt events,
this patch fix this issue.
The original patch was submitted by
Josef Ahmad <josef.ahmad@linux.intel.com>
http://git.yoctoproject.org/cgit/cgit.cgi/meta-intel-quark/tree/recipes-kernel/linux/files/0015-Quark-GPIO-1-2-quark.patch
Signed-off-by: Yong Li <yong.b.li@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pm_runtime_disable is called only in remove it is missed
out in the error path.
Fix the same.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current implementation only uses the first byte in val,
the second byte is always 0. Change it to use cpu_to_le16
to write the two bytes into the register
Cc: stable@vger.kernel.org
Signed-off-by: Yong Li <sdliyong@gmail.com>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit ff2b135922 ("gpio: make the gpiochip a real device"),
attempts to add a gpio chip prior to gpiolib initialization cause
the system to crash. This happens because gpio_bus_type has not been
registered yet. Defer creating gpio devices until after gpiolib has
been initialized to fix the problem.
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is possible that a gpio chip is registered before the gpiolib
initialization code has run. This means we can not use devm_ functions
to allocate memory at that time. Do it the old fashioned way.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In legacy pxa builds, ie. non device-tree and platform-data only builds,
pinctrl is not yet available. As a consequence, the pinctrl gpio
direction change function is a stub, returning always success.
In the current state, the gpio driver direction function believes the
pinctrl direction change was successful, and exits without actually
changing the gpio direction.
This patch changes the logic :
- if the pinctrl direction function fails, gpio direction will report
that failure
- if the pinctrl direction function succeeds, gpio direction is changed
by the gpio driver anyway.
This is sub optimal in the pinctrl aware case, as the gpio direction
will be changed twice: once by pinctrl function and another time by
the gpio direction function.
Yet it should be acceptable in this form, as this is functional for all
pxa platforms (device-tree and platform-data), and moreover changing a
gpio direction is very very seldom, usually in machine initialization,
seldom in drivers probe, and an exception for ac97 reset bug.
Fixes: a770d94637 ("gpio: pxa: add pin control gpio direction and request")
Reported-by: Guenter Roeck <guenter@roeck-us.net>
Tested-by: Guenter Roeck <guenter@roeck-us.net>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When firmware does not use _DSD properties that allow properly name GPIO
resources, the kernel falls back on parsing _CRS resources, and will
return entries described as GpioInt() as general purpose GPIOs even
though they are meant to be used simply as interrupt sources for the
device:
Device (ETSA)
{
Name (_HID, "ELAN0001")
...
Method(_CRS, 0x0, NotSerialized)
{
Name(BUF0,ResourceTemplate ()
{
I2CSerialBus(
0x10, /* SlaveAddress */
ControllerInitiated, /* SlaveMode */
400000, /* ConnectionSpeed */
AddressingMode7Bit, /* AddressingMode */
"\\_SB.I2C1", /* ResourceSource */
)
GpioInt (Edge, ActiveLow, ExclusiveAndWake, PullNone,,
"\\_SB.GPSW") { BOARD_TOUCH_GPIO_INDEX }
} )
Return (BUF0)
}
...
}
This gives troubles with drivers such as Elan Touchscreen driver
(elants_i2c) that uses devm_gpiod_get to look up "reset" GPIO line and
decide whether the driver is responsible for powering up and resetting
the device, or firmware is. In the above case the lookup succeeds, we
map GPIO as output and later fail to request client->irq interrupt that
is mapped to the same GPIO.
Let's ignore resources described as GpioInt() while parsing _CRS when
requesting output GPIOs (but allow them when requesting GPIOD_ASIS or
GPIOD_IN as some drivers, such as i2c-hid, do request GPIO as input and
then map it to interrupt with gpiod_to_irq).
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_TPS6586X
drivers/gpio/Kconfig: bool "TPS6586X GPIO"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_TPS65910
drivers/gpio/Kconfig: bool "TPS65910 GPIO"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Graeme Gregory <gg@slimlogic.co.uk>
Cc: Jorge Eduardo Candelaria <jedu@slimlogic.co.uk>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_PALMAS
drivers/gpio/Kconfig: bool "TI PALMAS series PMICs GPIO"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_SX150X
drivers/gpio/Kconfig: bool "Semtech SX150x I2C GPIO expander"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Gregory Bean <gbean@codeaurora.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_TC3589X
drivers/gpio/Kconfig: bool "TC3589X GPIOs"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Hanumath Prasad <hanumath.prasad@stericsson.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_RC5T583
drivers/gpio/Kconfig: bool "RICOH RC5T583 GPIO"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes use of the new .set_single_ended() callback to
set the GPIO line as open drain/open source using hardware.
The TC3589x can do this by either disabling the N-MOS
transistor (open drain) or the P-MOS transistor (open source)
of the output driver stage, in the first case making the signal
drive actively low and high impedance as "high" and in the second
case actively high and high impedance, which is as close to native
open drain support as we come.
Cc: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switch to use BIT(n) instead of (1 << n) which is less
to the point. Most GPIO drivers do this to avoid mistakes.
Also switch from using <linux/gpio.h> to the apropriate
<linux/gpio/driver.h> include.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO controllers has a special hardware bit we can flip
to support open drain / source. This means that on these hardwares
we do not need to emulate OD/OS by setting the line to input
instead of actively driving it high/low. Add an optional vtable
callback to the driver set_single_ended() so that driver can
implement this in hardware if they have it.
We may need a pinctrl_gpio_set_config() call at some point to
propagate this down to a backing pin control device on systems
with split GPIO/pin control.
Reported-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i2c_smbus_write_byte_data() can fail. To ensure the
cached buffer has consistent status with h/w status, don't
update the cached gpio->buffer if write fails.
Also refactor the code a bit by adding a tpic2810_set_mask_bits()
helper and use it to simplify the code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config GPIO_ZX
bool "ZTE ZX GPIO support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Jun Nie <jun.nie@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_XGENE
drivers/gpio/Kconfig: bool "APM X-Gene GPIO controller support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Feng Kan <fkan@apm.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_STA2X11
drivers/gpio/Kconfig: bool "STA2x11/ConneXt GPIO support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading
the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig for this driver is currently:
config GPIO_PL061
bool "PrimeCell PL061 GPIO support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_MVEBU
drivers/gpio/Kconfig: def_bool y
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_MOXART
drivers/gpio/Kconfig: bool "MOXART GPIO support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular references so that when reading
the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Jonas Jensen <jonas.jensen@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
drivers/gpio/Kconfig:config GPIO_MC9S08DZ60
drivers/gpio/Kconfig: bool "MX35 3DS BOARD MC9S08DZ60 GPIO functions"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_i2c_driver() uses the same init level priority as
builtin_i2c_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Wu Guoxing <b39297@freescale.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig for this driver is currently:
config GPIO_MB86S7X
bool "GPIO support for Fujitsu MB86S7x Platforms"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Kconfig currently controlling compilation of this code is:
config GPIO_BCM_KONA
bool "Broadcom Kona GPIO"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Ray Jui <rjui@broadcom.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These chips seem to have a 9th GPIO block (thus supporting 72 GPIOs)
which is configured through SuperIO register 0xd2 (output enable) and
0xd3 (simple I/O). This is also the reason why io_size is larger than
on IT8728 / IT8732. Unfortunately I don't have hardware to test this 9th
GPIO block.
I am also not sure about not configuring the Simple I/O registers as the
hardware I have only uses GPIO block 8. Reading back the values of
0xc0-0xc7 (as configured by the BIOS/EFI on my board) shows that all
have 0xff set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt for the corresponding pin is configured to trigger when the
pin state changes compared to a preconfigured state (Bit set in INTCON).
This state is set by setting/clearing the bit in DEFVAL.
In the interrupt handler we need also to check if the bit in INTCON is set
for level triggered interrupts.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The chip is also an 8 bit shift register which works out of the box as a GPO
expander with this patch
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code calls irq_domain_alloc_irqs_parent() in .alloc,
so it should call irq_domain_free_irqs_parent() accordingly in .free.
Fix it by switching to use irq_domain_free_irqs_common() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_resource() can return NULL, thus add NULL test to prevent NULL
pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code uses a uninitialized spin lock.
bgpio_init() already initialized a spin lock, so let's switch to use
&gc->bgpio_lock instead and remove the lock from struct men_z127_gpio.
Fixes: f436bc2726 "gpio: add driver for MEN 16Z127 GPIO controller"
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds a new ACPI HID, AMDIF030, in the pt_gpio_acpi_match.
Signed-off-by: YD Tseng<Yd_Tseng@asmedia.com.tw>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use gpio-generic to simplify this driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: YD Tseng <Yd_Tseng@asmedia.com.tw>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When using the GPIOLIB_IRQCHIP the gpiolib provides a
straight-forward implementation of request/release resources,
rely on that instead.
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This switches the mcp23s08 driver to use the gpiolib irqchip
helpers.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to set multiple outputs using a single SPI transfer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows to set multiple outputs using a single register write.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set it once is enough, so remove the second platform_set_drvdata() call.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
- New Device Support
- Supply device PCI IDs for Intel Broxton
- Fix-ups
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
- Bug Fixes
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gTBA
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
The mcp23s18 is configurable on clearing the interrupt on either reading
INTCAP or GPIO. Since driver reads INTCAP in IRQ and not the GPIO reg need
to set control byte for this mode.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pca953x_gpio_set_multiple() divides by 4 to convert from longs to bytes,
which assumes a 32-bit platform, and is not correct on 64-bit platforms.
Use "sizeof(...)" instead to fix this.
Cc: stable@vger.kernel.org
Fixes: b4818afeac ("gpio: pca953x: Add set_multiple to allow multiple bits to be set in one write.")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The standby GPIO controller can be used as a interrupt controller.
Select GPIOLIB_IRQCHIP when compiling this driver. Otherwise we get
a compilation error:
drivers/gpio/gpio-xgene-sb.c: In function 'xgene_gpio_sb_probe':
drivers/gpio/gpio-xgene-sb.c:312:10: error: 'struct gpio_chip'
has no member named 'irqdomain'
priv->gc.irqdomain = priv->irq_domain;
^
scripts/Makefile.build:295: recipe for target
'drivers/gpio/gpio-xgene-sb.o' failed
make[2]: *** [drivers/gpio/gpio-xgene-sb.o] Error 1
Fixes: 1013fc41 "gpio: xgene: Enable X-Gene standby GPIO as interrupt controller"
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the TPS65086 PMIC GPOs.
TPS65086 has four configurable GPOs that can be used for several
purposes. These are output only.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
I screwed up while merging the immutable branch for TPS65912,
so fixing it unbroken again.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO chip structure already has "parent" field which is used for the
same purpose as "dev" field in gpio_bank structure - store pointer on
GPIO device.
Hence, drop duplicated "dev" field from gpio_bank structure.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting gc->direction_output to gc->direction_output looks strange.
I think this change makes the intention more clear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
*read_reg and *write_reg can be removed because at all the places to call
them, we can just use gc->read_reg/gc->write_reg instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For devtype with specific gpio_dir_out implementation, current code is
wrong because below code sets both gc->direction_output and
mpc8xxx_gc->direction_output to the same function.
gc->direction_output = devtype->gpio_dir_out ?: gc->direction_output;
mpc8xxx_gc->direction_output = gc->direction_output;
Set mpc8xxx_gc->direction_output = gc->direction_output first to fix it.
This way mpc8xxx_gc->direction_output actually calls the standard
bgpio_dir_out() to update register.
Fixes: commit 42178e2a1e ("drivers/gpio: Switch gpio-mpc8xxx to use gpio-generic")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the mcp23s18 which is very similar to
the mcp23s17. A couple of control bits are not the same.
Notable IOCON_HAEN (s17 only) & IOCON_INTCC. Which can be ignored.
Patch changes the following:
- Add mcp23s18 types.
- Always set mirror bit if the dts defines mcp23s18. regardless of type.
Mirror bit is ignored on 8 bit devices anyway.
- In mcp23s08_probe use chip.ngpio instead of logic based on type
to determine number of gpio lins to increment by. This is set
appropiately by the call to mcp23s08_probe_one.
- Add mcp23s18 to device tree documentation.
- Remove statement that irqs don't work for spi. They do.
Tested with mcp23s18.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 16Z127 is a 32bit GPIO controller on a MCB FPGA.
Every single line can be configured as input and output.
Push pull and open drain are supported as well as setting
a debounce value for the input lines.
Signed-off-by: Andreas Werner <andy@wernerandy.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The implementation of lp3943_gpio_request/lp3943_gpio_free test pin_used
for tracing the pin usage. However, gpiolib already checks FLAG_REQUESTED
flag for the same purpose. So remove the redundant implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace calls to devm_request_mem_region and devm_ioremap with a
direct call to devm_ioremap_resource instead and modify error
handling.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more
clear.
A simplified version of the Coccinelle semantic patch that is used to
make this change is as follows:
//<smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size,e1,e;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\)))
{
- ...
- return ...;
-}
... when != res->start = e1
e =
-devm_ioremap(dev,res->start,size);
+devm_ioremap_resource(dev,res);
if
-(e == NULL)
+(IS_ERR(e))
{
...
-return ...;
+return PTR_ERR(e);
}
//</smpl>
Further, updated error handling by hand as devm_ioremap_resource
gives appropriate error messages, so remove unnecessary error
messages.
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TS-4800 is an i.MX515 board. Its GPIO driver should only be compiled
for this CPU or for test builds.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original code of gpiodev_add_to_list is not very clear which
lead to bugs or compiling warning, reference the following patches:
Bugs:
1. Commit ef7c755303 ("gpiolib: improve overlap check of range of
gpio").
2. Commit 96098df125 ("gpiolib: fix chip order in gpio list")
Warning:
1. Commit e28ecca6ea ("gpio: fix warning about iterator").
of gpio").
There is a off-list discussion about how to improve it consequently.
This commit try to follow this by rewriting the whole functions.
Tested pass with my gpio mockup driver and test scripts[1].
[1] http://www.spinics.net/lists/linux-gpio/msg09598.html
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These fields are initialized by bgpio_init() with exactly the same settings
so remove the redundant code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I named the field representing the current user of GPIO line as
"label" but this is too vague and ambiguous. Before anyone gets
confused, rename it to "consumer" and indicate clearly in the
documentation that this is a string set by the user of the line.
Also clean up leftovers in the documentation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We started to assign the gpio_device as parent for the sysfs
but this changes the expected layout of sysfs. Restore the
previous behaviour.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no build dependency for this driver, so enable COMPILE_TEST to get
better build coverage.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver has .can_sleep flag set.
So the pisosr_gpio_get() can be called from contexts that can sleep.
Thus use the cansleep() variant in pisosr_gpio_refresh().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio->load_gpio is optional, so use devm_gpiod_get_optional instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ret variable can contain error values and is compared with zero.
Its type must be signed.
The problem has been detected using coccinelle script
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both chip->base and chip->label are correctly set by bgpio_init().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use list_for_each_entry to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the code checking valid gpio count to cover both DT and non-DT cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio->load_gpio is optional, so use devm_gpiod_get_optional instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ret variable can contain error values and is compared with zero.
Its type must be signed.
The problem has been detected using coccinelle script
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Both chip->base and chip->label are correctly set by bgpio_init().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use list_for_each_entry to simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the code checking valid gpio count to cover both DT and non-DT cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R-Car GPIO driver handles Runtime PM for requested GPIOs only.
When using a GPIO purely as an interrupt source, no Runtime PM handling
is done, and the GPIO module's clock may not be enabled.
To fix this:
- Add .irq_request_resources() and .irq_release_resources() callbacks
to handle Runtime PM when an interrupt is requested,
- Add irq_bus_lock() and sync_unlock() callbacks to handle Runtime PM
when e.g. disabling/enabling an interrupt, or configuring the
interrupt type.
Fixes: d5c3d84657 "net: phy: Avoid polling PHY with PHY_IGNORE_INTERRUPTS"
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_get_gpiod_from_child() tries several property suffixes to find a
GPIO descriptor. If all suffixes fail and no probe deferral has been
detected, it returns the error of the last try.
However, if any but the last try fails with a real error (e.g. -EBUSY),
this error is not propagated, and -ENOENT will be returned.
This confuses drivers that e.g. want to detect if a GPIO is already in
use.
To fix this, change the loop logic to continue on -ENOENT, which
indicates the property was not found and the next suffix should be
tried, and propagate all other detected errors.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Support Opensource <support.opensource@diasemi.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call of gpiochip_remove() from error path.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Use devm_gpiochip_add_data() for GPIO registration.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Ray Jui <rjui@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: patches@opensource.wolfsonmicro.com
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call for gpiochip_remove() from remove callback.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call for gpiochip_remove() from error path.
Also remove the need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call for gpiochip_remove() from error path.
Also remove the need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Use devm_gpiochip_add_data() for GPIO registration and remove the
call for gpiochip_remove() from error path.
Also remove the need of driver callback .remove.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Alexander Shiyan <shc_work@mail.ru>
Add device managed APIs devm_gpiochip_add_data() and
devm_gpiochip_remove() for the APIs gpiochip_add_data()
and gpiochip_remove().
This helps in reducing code in error path and sometimes
removal of .remove callback for driver unbind.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
This fixes the wrongly indicated lines in the userspace
ABI: test for the right BITS, do not treat bit numbers as
bitmasks.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If spi_read() fails then we just returned but we missed unlocking the
mutex.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable X-Gene standby GPIO controller as interrupt controller to provide
its own resources. This avoids ambiguity where GIC interrupt resource is
use as X-Gene standby GPIO interrupt resource in user driver.
Signed-off-by: Y Vo <yvo@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a GPIO line ABI for getting name, label and a few select
flags from the kernel.
This hides the kernel internals and only tells userspace what it
may need to know: the different in-kernel consumers are masked
behind the flag "kernel" and that is all userspace needs to know.
However electric characteristics like active low, open drain etc
are reflected to userspace, as this is important information.
We provide information on all lines on all chips, later on we will
likely add a flag for the chardev consumer so we can filter and
display only the lines userspace actually uses in e.g. lsgpio,
but then we first need an ABI for userspace to grab and use
(get/set/select direction) a GPIO line.
Sample output from "lsgpio" on ux500:
GPIO chip: gpiochip7, "8011e000.gpio", 32 GPIO lines
line 0: unnamed unlabeled
line 1: unnamed unlabeled
(...)
line 25: unnamed "SFH7741 Proximity Sensor" [kernel output open-drain]
line 26: unnamed unlabeled
(...)
Tested-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio_chip label is useful for userspace to understand what
kind of GPIO chip it is dealing with. Let's store a copy of this
label in the gpio_device, add it to the struct passed to userspace
for GPIO_GET_CHIPINFO_IOCTL and modify lsgpio to show it.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Just as it says: after adding the proper interfaces to gpiolib,
this is no longer needed.
Suggested-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ks8695 gpio driver has its own copy of the irq_to_gpio()
function. This is completely unused in the mainline kernel
after we converted all remaining users several years ago,
so we can remove the definition as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The use of kmalloc() to allocate the gpio_device leaves the contained struct
device object in an unknown state. Calling dev_set_name() on a struct device
of unknown state can trigger the free() of an invalid pointer, as seen in the
following backtrace (collected by Tony Lindgren):
kfree
kobject_set_name_vargs
dev_set_name
gpiochip_add_data
omap_gpio_probe
platform_drv_probe
...
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Michael Welling <mwelling@ieee.org>
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Michael Welling <mwelling@ieee.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Josh Cartwright <joshc@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since devm_kzalloc can be failed in memory pressure,
it needs to check and return -ENOMEM
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .direction_output callback should set proper output level.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .direction_output callback should set proper output level.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
My left hand merges code to privatize the descriptor handling
while my right hand merges drivers that poke around and
disrespect with the same gpiolib internals.
So let's expose the proper APIs for drivers to ask the gpiolib
core if a line is marked as open drain or open source and
get some order around things so this driver compiles again.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a possible NULL pointer deference in the function,
davinci_gpio_probe due to the function, gpio2regs being able
to return a NULL pointer if it rans to get the registers for
the gpio devices on a davinci board. Furthermore if this does
arise return -ENXIO to signal callers that this case has arisen
and avoiding setting the regs or other pointer values on the
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most arches have an asm/gpio.h that merely includes linux/gpio.h. The
others select ARCH_HAVE_CUSTOM_GPIO_H, and when that's selected,
linux/gpio.h includes asm/gpio.h.
Therefore, code should include linux/gpio.h instead of including asm/gpio.h
directly.
Remove includes of asm/gpio.h, adding an include of linux/gpio.h when
necessary.
This is a follow-on to 7563bbf89d ("gpiolib/arches: Centralise
bolierplate asm/gpio.h").
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No flags are required for bgpio_init in the TS-4800 gpio driver. This
patch set zero instead. The driver will have the same behaviour since
the & operator between the flags already resulted to zero.
Fixes: 5041e79144 ("gpio: add TS-4800 fpga GPIO support")
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We move to manage this pointer under gpiolib control rather than
leave it in the subdevice's gpio_chip. We can not NULL it after
gpiochip_remove so at to keep things tight.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of keeping this reference to the pin ranges in the
client driver-supplied gpio_chip, move it to the internal
gpio_device as the drivers have no need to inspect this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the WinSystems WS16C48 GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the SMSC SCH311x GPIO driver, a
corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the Intel ICH series GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the AMD 8111 GPIO driver, a
corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the ACCES 104-IDIO-16 GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the ACCES 104-IDI-48 GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By the time request_region is called in the ACCES 104-DIO-48E GPIO
driver, a corresponding device structure has already been allocated. The
devm_request_region function should be used to help simplify the cleanup
code and reduce the possible points of failure.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO driver copyright boilerplate lacks the "or
later" verbiage regarding GPL compliant distribution. The MODULE_LICENSE
string should reflect the actual copyright license terms used.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Every time a descriptor is retrieved from the gpiolib, we issue
module_get() to reference count the module supplying the GPIOs.
We also need to call device_get() and device_put() as we also
reference the backing gpio_device when doing this.
Since the sysfs GPIO interface is using gpiod_get() this will
also reference count the sysfs requests until all GPIOs are
unexported.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some information about the GPIO chip need to stay around also
after the gpio_chip has been removed and only the gpio_device
persist. The base and ngpio are such things, for example we
don't want a new chip arriving to overlap the number space
of a dangling gpio_device, and the chardev may still query
the device for the number of lines etc.
Note that the code that assigns base and insert gpio_device
into the global list no longer check for a missing gpio_chip:
we respect the number space allocated by any other gpio_device.
As a consequence of the gdev being referenced directly from
the gpio_desc, we need to verify it differently from all
in-kernel API calls that fall through to direct queries to
the gpio_chip vtable: we first check that desc is !NULL, then
that desc->gdev is !NULL, then, if desc->gdev->chip is NULL,
we *BAIL OUT* without any error, so as to manage the case
where operations are requested on a device that is gone.
These checks were non-uniform and partly missing in the past:
so to simplify: create the macros VALIDATE_DESC() that will
return -EINVAL if the desc or desc->gdev is missing and just
0 if the chip is gone, and conversely VALIDATE_DESC_VOID()
for the case where the function does not return an error.
By using these macros, we get warning messages about missing
gdev with reference to the right function in the kernel log.
Despite the macro business this simplifies the code and make
it more readable than if we copy/paste the same descriptor
checking code into all code ABI call sites (IMHO).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This kind of hacks disturbs the refactoring of the gpiolib.
The descriptor table belongs to the gpiolib, if we want to know
something about something in it, use or define the proper accessor
functions. Let's add this gpiochip_lins_is_irq() to do what the
sunxi driver is trying at so we can privatize the descriptors
properly.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need gpio_device to hold the descriptors so that they can
be lifecycled with the struct gpio_device held from userspace.
Move the descriptor array into gpio_device. Also rename it from
"desc" (singularis) to "descs" (pluralis) to reflect the fact
that it is an array.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since gpio_device is the struct that survives if the backing
gpio_chip is removed, move the sysfs mock device to this state
container so it becomes part of the dangling state of the
GPIO device on removal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When the device core reference count for the device goes to
0 and it calls .release() we free resources and so can also
finally free up the GPIO state container, struct gpio_device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for the TPS65912 PMIC GPIOs.
TPS65912 has five configurable GPIOs that can be used for several
purposes.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old tps65912 driver is being replaced, delete old driver.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Driver for the GPIO block found in ti's tps65218 pmics.
The device has two GPIOs and one GPO pin which can be configured as follows:
GPIO1:
-general-purpose, open-drain output controlled by GPO1 user bit and/or
sequencer
-DDR3 reset input signal from SOC. Signal is either latched or
passed-trough to GPO2 pin. See below for details.
GPO2:
-general-purpose output controlled by GPO2 user bit
-DDR3 reset output signal. Signal is controlled by GPIO1 and PGOOD.
See below for details.
-Output buffer can be configured as open-drain or push-pull.
GPIO3:
-general-purpose, open-drain output controlled by GPO3 user bit and/or
sequencer
-reset input-signal for DCDC1 and DCDC2.
The input configurations are not meant to be used by the user so the driver
only offers GPOs.
v2: Added request routine that evaluates the fw config flags and removed module
owner
v3: Added .direction_input() routine, and took care of all Linus Walleij
suggestions (clamp to bool, use proper include)
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add driver for TI TPIC2810 8-Bit LED Driver with I2C Interface.
The TPIC2810 has 8 open-drain outputs that can but used to drive
LEDs and other low-side switched resistive loads.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add generic parallel-in/serial-out shift register GPIO driver.
This includes SPI compatible devices like SN74165 serial-out shift
registers and the SN65HVS88x series of industrial serializers that can
be read over the SPI bus and used for GPI (General Purpose Input).
Signed-off-by: Andrew F. Davis <afd@ti.com>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add myself to the copyright list and remove the reference to Atheros'
BSP as nothing is left of this code.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the interrupt controller using GPIOLIB_IRQCHIP.
Both edges isn't supported by the chip and has to be emulated
by switching the polarity on each interrupt.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we now allow the driver to be built as a module it should be
removable.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To allow building the driver in compile tests we must drop the
dependency on asm/mach-ath79/ar71xx_regs.h. For this we replace the
include with local definition of the registers needed for this driver.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop most of the code in favor of the generic MMIO GPIO driver.
As the driver now depend on CONFIG_GPIO_GENERIC also add a Kconfig
entry to make the driver optional.
We leave the base pointer and lock in the data struct because they are
needed for the IRQ support.
Signed-off-by: Alban Bedel <albeu@free.fr>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Driver only needs to allocate for [ngpio / 32] controllers,
as each controller handles 32 gpios. But the current driver
allocates for ngpio of which the extra allocated are unused.
Fix it be registering only the required number of controllers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the first parameter of irq_domain_add_legacy is NULL.
irq_find_host function returns NULL when we do not populate the of_node
and hence irq_of_parse_and_map call fails whenever we want to request a
gpio irq. This fixes the request_irq failures for gpio interrupts.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A new chardev that is to be used for userspace GPIO access is
added in this patch. It is intended to gradually replace the
horribly broken sysfs ABI.
Using a chardev has many upsides:
- All operations are per-gpiochip, which is the actual
device underlying the GPIOs, making us tie in to the
kernel device model properly.
- Hotpluggable GPIO controllers can come and go, as this
kind of problem has been know to userspace for character
devices since ages, and if a gpiochip handle is held in
userspace we know we will break something, whereas the
sysfs is stateless.
- The one-value-per-file rule of sysfs is really hard to
maintain when you want to twist more than one knob at a time,
for example have in-kernel APIs to switch several GPIO
lines at the same time, and this will be possible to do
with a single ioctl() from userspace, saving a lot of
context switching.
We also need to add a new bus type for GPIO. This is
necessary for example for userspace coldplug, where sysfs is
traversed to find the boot-time device nodes and create the
character devices in /dev.
This new chardev ABI is *non* *optional* and can be counted
on to be present in the future, emphasizing the preference
of this ABI.
The ABI only implements one single ioctl() to get the name
and number of GPIO lines of a chip. Even this is debatable:
see it as a minimal example for review. This ABI shall be
ruthlessly reviewed and etched in stone.
The old /sys/class/gpio is still optional to compile in,
but will be deprecated.
Unique device IDs are created using IDR, which is overkill
and insanely scalable, but also well tested.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use the new struct device inside gpio_chip to related debug
prints and warnings, and we also add it to the debugfs dump.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO chips have been around for years, but were never real devices,
instead they were piggy-backing on a parent device (such as a
platform_device or amba_device) but this was always optional.
GPIO chips could also exist without any device at all, with its
struct device *parent (ex *dev) pointer being set to null.
When sysfs was in use, a mock device would be created, with the
optional parent assigned, or just floating orphaned with NULL
as parent.
If sysfs is active, it will use this device as parent.
We now create a gpio_device struct containing a real
struct device and move the subsystem over to using that. The
list of struct gpio_chip:s is augmented to hold struct
gpio_device:s and we find gpio_chips:s by first looking up
the struct gpio_device.
The struct gpio_device is designed to stay around even if the
gpio_chip is removed, so as to satisfy users in userspace
that need a backing data structure to hold the state of the
session initiated with e.g. a character device even if there is
no physical chip anymore.
From this point on, gpiochips are devices.
Cc: Johan Hovold <johan@kernel.org>
Cc: Michael Welling <mwelling@ieee.org>
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The new Layerscape platforms has the same ip block/controller
as GPIO on PowerPC platforms(MPC8XXX), but the GPIO registers
may be big or little endian. So the code needs to get the
endian property from DTB, then make additional functions to
fit all the PowerPC/Layerscape GPIO register read/write
operations.
gpio-generic.c provides an universal infrastructure for both
big and little endian register operations. So switch the
gpio-mpc8xxx to use gpio-generic can simplify the driver and
reduce a lot of code.
The IRQ and some workaround parts in gpio-mpc8xxx.c will be
updated with the new API interfaces but following the
original functionalities.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The TS-4800 GPIO driver provide support for the GPIOs available
on the Technologic Sytems board FPGA. It allows to set
direction and read/write states.
It uses the generic gpio driver.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio-mpc8xxx.c should can support qoriq and
Layerscape platforms.
Signed-off-by: Liu Gang <Gang.Liu@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add F81866 GPIO supports
Fintek F81866 is a SuperIO. It contains HWMON/GPIO/Serial Ports.
and it has totally 72(9x8 sets) gpio pins.
Here is the PDF spec:
http://www.alldatasheet.com/datasheet-pdf/pdf/459085/FINTEK/F81866AD-I.html
The control method is the same with F7188x, but we should care the address
of GPIO8x.
GPIO address is below:
GPIO0x based: 0xf0
GPIO1x based: 0xe0
GPIO2x based: 0xd0
GPIO3x based: 0xc0
GPIO4x based: 0xb0
GPIO5x based: 0xa0
GPIO6x based: 0x90
GPIO7x based: 0x80
GPIO8x based: 0x88 <-- not 0x70.
Signed-off-by: Peter Hung <hpeter+linux_kernel@gmail.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E device provides 48 lines digital I/O via two
Programmable Peripheral Interface (PPI) chips of type 82C55. Bit C3 at
each 24-bit Group can be used as an external interrupt, triggered by a
rising edge.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the dio_48e_base module parameter. The interrupt line number for the
device may be configured via the dio_48e_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WinSystems WS16C48 device provides 48 lines of digital I/O. In
addition, the first 24 lines may be used for interrupt-handled edge
detection; rising edge detection and falling edge detection are
supported.
This driver provides GPIO and IRQ support for these 48 channels of
digital I/O. The base port address for the device may be configured via
the ws16c48_base module parameter. The interrupt line number for the
device may be configured via the ws16c48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDI-48 can differentiate between its own and other
devices' interrupt requests. Therefore, IRQ sharing is possible and
should be permitted.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On failure to setup the irq altera_gpio_probe would return an error
but not go to cleanup. This resulted in kernel fault
"Unable to handle kernel paging request at virtual address xxxxxxxx"
later on in of_gpiochip_find_and_xlate.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings several
of the more minor and older platforms we have closer to multiplatform
support. Among these are MMP, S3C64xx, Orion5x, mv78xx0 and realview
Much of this is moving around header files from old mach directories,
but there are also some cleanup patches of debug_ll (lowlevel debug
per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=z1AW
-----END PGP SIGNATURE-----
Merge tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform code updates from Arnd Bergmann:
"This branch is the culmination of 5 years of effort to bring the ARMv6
and ARMv7 platforms together such that they can all be enabled and
boot the same kernel. It has been a tremendous amount of cleanup and
refactoring by a huge number of people, and creation of several new
(and major) subsystems to better abstract out all the platform details
in an appropriate manner.
The bulk of this branch is a large patchset from Arnd that brings
several of the more minor and older platforms we have closer to
multiplatform support. Among these are MMP, S3C64xx, Orion5x, mv78xx0
and realview Much of this is moving around header files from old mach
directories, but there are also some cleanup patches of debug_ll
(lowlevel debug per-platform options) and other parts.
Linus Walleij also has some patchs to clean up the older ARM Realview
platforms by finally introducing DT support, and Rob Herring has some
for ARM Versatile which is now DT-only. Both of these platforms are
now multiplatform.
Finally, a couple of patches from Russell for Dove PMU, and a fix from
Valentin Rothberg for Exynos ADC, which were rebased on top of the
series to avoid conflicts"
* tag 'armsoc-multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: realview: don't select SMP_ON_UP for UP builds
ARM: s3c: simplify s3c_irqwake_{e,}intallow definition
ARM: s3c64xx: fix pm-debug compilation
iio: exynos-adc: fix irqf_oneshot.cocci warnings
ARM: realview: build realview-dt SMP support only when used
ARM: realview: select apropriate targets
ARM: realview: clean up header files
ARM: realview: make all header files local
ARM: no longer make CPU targets visible separately
ARM: integrator: use explicit core module options
ARM: realview: enable multiplatform
ARM: make default platform work for NOMMU
ARM: debug-ll: move DEBUG_LL_UART_EFM32 to correct Kconfig location
ARM: defconfig: use correct debug_ll settings
ARM: versatile: convert to multi-platform
ARM: versatile: merge mach code into a single file
ARM: versatile: switch to DT only booting and remove legacy code
ARM: versatile: add DT based PCI detection
ARM: pxa: mark ezx structures as __maybe_unused
ARM: pxa: mark raumfeld init functions as __maybe_unused
...
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better reflect
the fact that this is not the GPIO struct device abstraction. We will
add that soon so this would be totallt confusing.
- It was noted that the driver .get_value() callbacks was
sometimes reporting negative -ERR values to the gpiolib core, expecting
them to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than zero"
to indicate that a line was active. As some would have bit 31 set to
indicate "line active" it clashed with negative error codes. This is
fixed by the largeish series clamping values in all drivers with
!!value to [0,1] and then augmenting the code to propagate error codes
to consumers. (Includes some ACKed patches in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of() design
pattern is indeed very nice, but we want to reform the struct gpio_chip
to be a non-volative, stateless business, and keep states internal to
the gpiolib to be able to hold on to the state when adding a proper
userspace ABI (character device) further down the road. To achieve this,
drivers need a handle at the internal state that is not dependent on
their struct gpio_chip() so we add gpiochip_add_data() and
gpiochip_get_data() following the pattern of many other subsystems.
All the "use gpiochip data pointer" patches transforms drivers to this
scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that removed.
Instead of having a separate mm_gpio_chip struct for these generic
drivers, merge that into struct gpio_chip, simplifying the code and
removing the need for separate and confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from the
OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir, but
the branch is merged here too to account for infrastructural changes).
- The sx150x driver now supports the sx1502.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=63rR
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"Here is the bulk of GPIO changes for v4.5.
Notably there are big refactorings mostly by myself, aimed at getting
the gpio_chip into a shape that makes me believe I can proceed to
preserve state for a proper userspace ABI (character device) that has
already been proposed once, but resulted in the feedback that I need
to go back and restructure stuff. So I've been restructuring stuff.
On the way I ran into brokenness (return code from the get_value()
callback) and had to fix it. Also, refactored generic GPIO to be
simpler.
Some of that is still waiting to trickle down from the subsystems all
over the kernel that provide random gpio_chips, I've touched every
single GPIO driver in the kernel now, oh man I didn't know I was
responsible for so much...
Apart from that we're churning along as usual.
I took some effort to test and retest so it should merge nicely and we
shook out a couple of bugs in -next.
Infrastructural changes:
- In struct gpio_chip, rename the .dev node to .parent to better
reflect the fact that this is not the GPIO struct device
abstraction. We will add that soon so this would be totallt
confusing.
- It was noted that the driver .get_value() callbacks was sometimes
reporting negative -ERR values to the gpiolib core, expecting them
to be propagated to consumer gpiod_get_value() and gpio_get_value()
calls. This was not happening, so as there was a mess of drivers
returning negative errors and some returning "anything else than
zero" to indicate that a line was active. As some would have bit
31 set to indicate "line active" it clashed with negative error
codes. This is fixed by the largeish series clamping values in all
drivers with !!value to [0,1] and then augmenting the code to
propagate error codes to consumers. (Includes some ACKed patches
in other subsystems.)
- Add a void *data pointer to struct gpio_chip. The container_of()
design pattern is indeed very nice, but we want to reform the
struct gpio_chip to be a non-volative, stateless business, and keep
states internal to the gpiolib to be able to hold on to the state
when adding a proper userspace ABI (character device) further down
the road. To achieve this, drivers need a handle at the internal
state that is not dependent on their struct gpio_chip() so we add
gpiochip_add_data() and gpiochip_get_data() following the pattern
of many other subsystems. All the "use gpiochip data pointer"
patches transforms drivers to this scheme.
- The Generic GPIO chip header has been merged into the general
<linux/gpio/driver.h> header, and the custom header for that
removed. Instead of having a separate mm_gpio_chip struct for
these generic drivers, merge that into struct gpio_chip,
simplifying the code and removing the need for separate and
confusing includes.
Misc improvements:
- Stabilize the way GPIOs are looked up from the ACPI legacy
specification.
- Incremental driver features for PXA, PCA953X, Lantiq (patches from
the OpenWRT community), RCAR, Zynq, PL061, 104-idi-48
New drivers:
- Add a GPIO chip to the ALSA SoC AC97 driver.
- Add a new Broadcom NSP SoC driver (this lands in the pinctrl dir,
but the branch is merged here too to account for infrastructural
changes).
- The sx150x driver now supports the sx1502"
* tag 'gpio-v4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (220 commits)
gpio: generic: make bgpio_pdata always visible
gpiolib: fix chip order in gpio list
gpio: mpc8xxx: Do not use gpiochip_get_data() in mpc8xxx_gpio_save_regs()
gpio: mm-lantiq: Do not use gpiochip_get_data() in ltq_mm_save_regs()
gpio: brcmstb: Allow building driver for BMIPS_GENERIC
gpio: brcmstb: Set endian flags for big-endian MIPS
gpio: moxart: fix build regression
gpio: xilinx: Do not use gpiochip_get_data() in xgpio_save_regs()
leds: pca9532: use gpiochip data pointer
leds: tca6507: use gpiochip data pointer
hid: cp2112: use gpiochip data pointer
bcma: gpio: use gpiochip data pointer
avr32: gpio: use gpiochip data pointer
video: fbdev: via: use gpiochip data pointer
gpio: pch: Optimize pch_gpio_get()
Revert "pinctrl: lantiq: Implement gpio_chip.to_irq"
pinctrl: nsp-gpio: use gpiochip data pointer
pinctrl: vt8500-wmt: use gpiochip data pointer
pinctrl: exynos5440: use gpiochip data pointer
pinctrl: at91-pio4: use gpiochip data pointer
...
Pull input updates from Dmitry Torokhov:
- new driver for eGalaxTouch serial touchscreen
- new driver for TS-4800 touchscreen
- an update for Goodix touchscreen driver
- PS/2 mouse module was reworked to limit number of protocols we try on
pass-through ports to speed up their detection time
- wacom_w8001 touchscreen driver now reports pen and touch via separate
instances of input devices
- other driver changes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (42 commits)
Input: elantech - mark protocols v2 and v3 as semi-mt
Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE
Input: gpio-keys - fix check for disabling unsupported keys
Input: omap-keypad - remove dead check
Input: ti_am335x_tsc - fix HWPEN interrupt handling
Input: omap-keypad - set tasklet data earlier
Input: rohm_bu21023 - fix handling of retrying firmware update
Input: ALPS - report v3 pinnacle trackstick device only if is present
Input: ALPS - detect trackstick presence for v7 protocol
Input: pcap_ts - use to_delayed_work
Input: bma150 - constify bma150_cfg structure
Input: i8042 - add Fujitsu Lifebook U745 to the nomux list
Input: egalax_ts_serial - fix potential NULL dereference on error
Input: uinput - sanity check on ff_effects_max and EV_FF
Input: uinput - rework ABS validation
Input: uinput - add new UINPUT_DEV_SETUP and UI_ABS_SETUP ioctl
Input: goodix - use "inverted_[xy]" flags instead of "rotated_screen"
Input: goodix - add axis swapping and axis inversion support
Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
Input: goodix - add power management support
...
In some situations the gpio_list order is not correct.
As a consequence gpiochip_find_base returns the same
base number twice. This happens when a first ship is added
with manual base number, then other ships are added using
automatic base number.
To prevent this behaviour, this patch add the new chip after
the last element of the gpio list.
Signed-off-by: Julien Grossholtz <julien.grossholtz@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 709d71a17c ("gpio: mpc8xxx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.
Fixes: 709d71a17c ("gpio: mpc8xxx: use gpiochip data pointer")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 6aa7dbfa28 ("gpio: mm-lantiq: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). However, the data
pointer is not yet set by the time the save_regs function is called.
Fixes: 6aa7dbfa28 ("gpio: mm-lantiq: use gpiochip data pointer")
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The CS47L24 and WM1831 codecs only have two GPIO lines, but are
otherwise similar to the WM8280.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
BMIPS_GENERIC (arch/mips/bmips) is the Kconfig symbol associated with
Broadcom MIPS-based STB chips. Since this driver is perfectly usable on
these platforms as well, allow using it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Broadcom MIPS-based STB chips endianness is configured by boot strap,
which also reverses all bus endianness (i.e., big-endian CPU + big
endian bus ==> native endian I/O).
Other architectures (e.g., ARM) either do not support big endian, or
else leave I/O in little endian mode.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A cleanup patch replaced bgpio_chip with gpio_chip but missed
two references to the bgpio_chip:
drivers/gpio/gpio-moxart.c:60:19: error: use of undeclared identifier 'bgc'; did you mean 'gc'?
gc->bgpio_data = bgc->read_reg(bgc->reg_set);
drivers/gpio/gpio-moxart.c:35:20: note: 'gc' declared here
drivers/gpio/gpio-moxart.c:60:33: error: use of undeclared identifier 'bgc'; did you mean 'gc'?
gc->bgpio_data = bgc->read_reg(bgc->reg_set);
This adds the missing change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0f4630f372 ("gpio: generic: factor into gpio_chip struct")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 097d88e94c ("gpio: xilinx: use gpiochip data pointer") replaces
the use of container_of() with gpiochip_get_data(). Unfortunately, the
data pointer is not yet set by the time xgpio_save_regs() is called,
causing a system hang.
Fixes: 097d88e94c ("gpio: xilinx: use gpiochip data pointer")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The double negation is costly and can be avoided by shifting the
register value before masking the requested bit.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For completion, sweep the floor from all gpiochip_add() usage so
we can remove that function and get rid of the function wrapper
gpiochip_add().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Kamlakant Patel <kamlakant.patel@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Feng Kan <fkan@apm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: patches@opensource.wolfsonmicro.com
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Cc: Margarita Olaya <magi@slimlogic.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-By: Rhyland Klein <rklein@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Daniel Mack <zonque@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Thierry Reding <treding@nvidia.com>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Markus Pargmann <mpa@pengutronix.de>
Cc: Toby Smith <toby@tismith.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Andrew Chew <achew@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Reviewed-by: David Daney <david.daney@cavium.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Cc: John Crispin <blogic@openwrt.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Feng Tang <feng.tang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: wu guoxing <b39297@freescale.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-By: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Nicholas Krause <xerofoify@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Roland Stigge <stigge@antcom.de>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Milo Kim <milo.kim@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Brunner Michael <Michael.Brunner@kontron.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Andreas Bofjall <andreas@gazonk.org>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Zhu, Lejun <lejun.zhu@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Michael Buesch <m@bues.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Markus Mayer <markus.mayer@linaro.org>
Cc: Tim Kryger <tim.kryger@linaro.org>
Cc: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Cc: Mark Brown <broonie@kernel.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: YD Tseng <ltyu101@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Tien Hock Loh <thloh@altera.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Cc: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the data pointer added to the gpio_chip
to store a pointer to the state container instead of relying on
container_of().
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The separate struct bgpio_chip has been a pain to handle, both
by being confusingly similar in name to struct gpio_chip and
for being contained inside a struct so that struct gpio_chip
is contained in a struct contained in a struct, making several
steps of dereferencing necessary.
Make things simpler: include the fields directly into
<linux/gpio/driver.h>, #ifdef:ed for CONFIG_GENERIC_GPIO, and
get rid of the <linux/basic_mmio_gpio.h> altogether. Prefix
some of the member variables with bgpio_* and add proper
kerneldoc while we're at it.
Modify all users to handle the change and use a struct
gpio_chip directly. And while we're at it: replace all
container_of() dereferencing by gpiochip_get_data() and
registering the gpio_chip with gpiochip_add_data().
Cc: arm@kernel.org
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Rabin Vincent <rabin@rab.in>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: bcm-kernel-feedback-list@broadcom.com
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Liviu Dudau <Liviu.Dudau@arm.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the same spirit as we add an optional void *data argument
to the gpiochip_add_data() call, we need this also for
of_mm_gpiochip_add().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a void * pointer to gpio_chip so that driver can
assign and retrieve some states. This is done to get rid of
container_of() calls for gpio_chips embedded inside state
containers, so we can remove the need to have the gpio_chip
or later (planned) struct gpio_device be dynamically allocated
at registration time, so that its struct device can be properly
reference counted and not bound to its parent device (e.g.
a platform_device) but instead live on after unregistration
if it is opened by e.g. a char device or sysfs.
The data is added with the new function gpiochip_add_data()
and for compatibility we add static inline wrapper function
gpiochip_add() that will call gpiochip_add_data() with
NULL as argument. The latter will be removed once we have
exorcised gpiochip_add() from the kernel.
gpiochip_get_data() is added as a static inline accessor
for drivers to quickly get their data out.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cppcheck reports this:
(style) int result is returned as long value. If the return
value is long to avoid loss of information, then you have
loss of information.
This can be fixed with (1UL << pin) but that is the same
as using <linux/bitops.h> that already use 1UL so take
this approach.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a GPIO is used as an interrupt in ACPI, the irq_type was not
available for device driver.
Make available polarity and triggering information in acpi_find_gpio by
renaming acpi_gpio_info field active_low to polarity and adding triggering
field (edge/level).
For sanity, in gpiolib.c replace info.active_low by
"info.polarity == GPIO_ACTIVE_LOW".
Set the irq_type if necessary in acpi_dev_gpio_irq_get.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
We were getting build warning about "iterator" being used uninitialized.
Use iterator properly to fix the build warning and in the process remove
the variable "pos" which is not required now.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 45ad7db90b.
We have fixed all the drivers that were returning ambious values
not clamped to [0,1] or an error code, so return the error
propagating behaviour of the API.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
This also makes the driver start to return the error code, as the
end of the series make this work.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
This also starts to propagate the error code from the I2C
transaction as the end of the series adds support for that.
Cc: Wei Chen <Wei.Chen@csr.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Also start returning the error code if something fails, as the
end of the series augment the core to support this.
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Feng Tang <feng.tang@intel.com>
Cc: Tomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Also start to propagate the error code here as the end of the
series fixes this to work for all drivers.
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by:Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Roland Stigge <stigge@antcom.de>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Brunner Michael <Michael.Brunner@kontron.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Acked-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Magnus Damm <damm@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we want gpio_chip .get() calls to be able to return negative
error codes and propagate to drivers, we need to go over all
drivers and make sure their return values are clamped to [0,1].
We do this by using the ret = !!(val) design pattern.
Cc: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Performing a read operation on the IRQ Status register will clear the
IRQ latch. Since a read operation on the IRQ Status register must be
performed in the IRQ handler in order to determine if the IRQ was in
fact generated by the device, the IRQ latch is consequently cleared by
the IRQ handler. A spinlock is used to guarantee that each IRQ is
serviced in the order it was received.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
The commit "gpio: pxa: change the interrupt management" should have
taken care of moving an ifdef to not englobe irqdomain related
structures anymore, as they are used now for all builds.
This repairs the broken builds where CONFIG_OF=n.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit e20538b82f
("gpio: Propagate errors from chip->get()")
started to propagate errors from the .get() functions since
we can get errors from the infrastructure of e.g. slowbus
GPIO expanders.
However it turns out a bunch of drivers relied on the core
to clamp the value, so we need to revert to the old behaviour
and go over all drivers and fix them to conform to the
expectations of the core before we go back to propagating
the error code.
Cc: stable@vger.kernel.org # 4.3+
Cc: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Fixes: e20538b82f ("gpio: Propagate errors from chip->get()")
Reported-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bgpio_get_set() call should return a value clamped to [0,1],
the current code will return a negative value if reading
bit 31, which turns the value negative as this is a signed value
and thus gets interpreted as an error by the gpiolib core.
Found on the gpio-mxc but applies to any MMIO driver.
Cc: stable@vger.kernel.org # 4.3+
Cc: kernel@pengutronix.de
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Fixes: e20538b82f ("gpio: Propagate errors from chip->get()")
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 1cfadea8f3
"gpio: pch: allow use from device tree"
makes the driver not compile unless CONFIG_OF_GPIO is set.
Fix it.
Cc: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a pin control driver is available, use it to change the gpio
direction. If not fallback to directly manipulating the gpio direction
register.
The reason to use the pin control driver first is that pin control in
pxa2xx architecture implies changing the gpio direction, even for non
gpio functions. In order to do it atomically, only one driver should
control the gpio direction, and if a pin controller is available, it has
to be him.
There is a small catch : if CONFIG_PINCTRL is selected, then a pinctrl
driver has to be probed. If not, gpio_request() will return
-EPROBE_DEFER as pinctrl_request_gpio() returns it in that case.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PL061 supports interrupts and those can be wakeup interrupts. We
need to provide support for configuring those interrupts as wakeup
sources.
This patch adds irq_set_wake callback for PL061 so that GPIO interrupts
can be configured as wakeup.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO hogs registration is call at the end of gpiochip_add() function.
Calling sequence is:
gpiochip_add -> of_gpiochip_add -> of_gpiochip_scan_hogs ->
gpiod_hog -> gpiochip_request_own_desc -> __gpiod_request ->
chip->request -> zynq_gpio_request which calls pm_runtime_get_sync()
which returns -13 because PM is not initialized yet.
Initialize PM before gpiochip_add is called to fix this issue.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should not fall back to the legacy unnamed gpio lookup style if the
driver requests gpios with different names, because we'll give out the same
gpio twice. Let's keep track of the names that were used for the device and
only do the fallback for the first name used.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enum is used in the gpiolib.h header file, yet
<linux/gpio/consumer.h> is not included so plainly including this
file (and some drivers do) will raise compile problems.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the Renesas R-Car GPIO driver cannot find a functional clock, it
prints a warning, .e.g.
gpio_rcar ffc40000.gpio: unable to get clock
and continues, as the clock is optional, depending on the SoC type.
This warning may confuse users.
To fix this, add a flag to indicate that the clock is mandatory or
optional:
- If the clock is mandatory (on R-Car Gen2 and Gen3), a missing clock
is now treated as a fatal error,
- If the clock is optional (on R-Car Gen1), the warning is no longer
printed.
Suggested-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds. The driver doesn't need to use platform data
anymore, hence remove platform data configuration.
Make gpio_rcar_priv.has_both_edge_trigger a boolean for consistency with
gpio_rcar_info.has_both_edge_trigger.
Move gpio_rcar_priv.irq_parent down while we're at it, to prevent gaps
on 64-bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These new helpers simplify implementing multi-driver modules and
properly handle failure to register one driver by unregistering all
previously registered drivers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 uses a single interrupt to indicate a possible
change-of-state in any of the digital input lines. As such, only a
single write to the device's "Clear Interrupt" register is necessary to
acknowledge the IRQ for all respective GPIO.
This patch moves the "Clear Interrupt" register write operation from the
irq_ack callback to the IRQ handler function, wherefore each interrupt
may be cleared respectively by executing a single outb call at the end
of the idio_16_irq_handler function, rather than multiple redundant outb
calls as a result of the generic_handle_irq call for each masked GPIO.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCI/USB expander menus already depend on PCI/USB, drop subdependecies
on individual drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
[Rebased to the GPIO tree]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow GPIOs from the gpio-pch driver to be referenced from device tree
by simply setting the struct gpio_chip of_node pointer to that of the
struct pci_dev.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow the pch_gpio driver to be built for MIPS platforms, in preparation
for use on the MIPS Boston board.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the 74x164 driver assembles an SPI message from an array of
one-byte SPI transfers, one for each daisy-chained shift register, as
the first byte sent will end up in the last register.
This array is allocated and deallocated on each GPIO write access.
By storing the data in the internal buffer in reverse order, we can
use a single SPI transfer with the internal buffer directly, simplifying
the code a lot, and avoiding memory (de)allocations.
This also avoids transient values on the GPIO outputs when using an SPI
master that cannot keep the hardware chip select asserted in between
multiple transfers (and would need cs-gpios for proper operation).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Mark Brown <broonie@kernel.org>
[Rebased changing .dev to .parent]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
By moving the internal buffer to the end of struct gen_74x164_chip and
converting it from a pointer to a zero-sized array, it can be allocated
together with gen_74x164_chip, reducing the number of managed
allocations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt management is changed by this patch to rely on chip data
instead of chained interrupts.
The main goal is to loosen the dependency on the global pxa chip
structure in favor of the passed chip data. The secondary goal is to
better show in /proc/interrupts the difference between interrupts for
gpio0 and gpio1 (directly wired to interrupt controller), and the other
gpios (wired onto a third line in the interrupt controller).
The last advantage of this patch is that the interrupt is actually
requested, so that another driver cannot steal this line, or overwrite
the handler.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the device managed ioremap to simplify the probe function.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pxa gpio IP is provided by one chip, which holds multiple banks.
Another reason the driver should register only one gpiochip instead of
multiple gpiochips (ie. 1 per each bank) is that for pincontrol and
devicetree integration (think gpio-ranges), it's impossible to have the
contiguous pin range 0..127 mapped to gpios 0..127.
This patch, amongst other thinks, paves the path to loosen the bond with
the global structure variable pxa_gpio_chip.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After adding the DT matching in
commit 6f29c9afbe
"gpio: pca935x: fix of-only probed devices"
compilation fails like this:
CC [M] drivers/gpio/gpio-pca953x.o
gpio-pca953x.c: In function ‘pca953x_probe’:
gpio-pca953x.c:693:11: error: implicit declaration of
function ‘of_match_device’ [-Werror=implicit-function-declaration]
match = of_match_device(pca953x_dt_ids, &client->dev);
^
gpio-pca953x.c:693:9: warning: assignment makes pointer from
integer without a cast [-Wint-conversion]
match = of_match_device(pca953x_dt_ids, &client->dev);
^
cc1: some warnings being treated as errors
../scripts/Makefile.build:264: recipe for target
'drivers/gpio/gpio-pca953x.o' failed
After removing the conditional inclusion guards compilation
works fine again. Might be a module problem so that
fix.
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pca953x device is probed from OF using the proper OF probing then
the i2c-client will be NULL and the device probe will fail as id is NULL
and it isn't an ACPI device (previous drivers would simply OOPS out).
Add support for the of_device_id table having the same data as the others
so that the correct paths will be taken when registering a device.
An example of current valid of node which did not work:
gpio@38 {
compatible = "onsemi,pca9654", "nxp,pca9534";
reg = <0x38>;
interrupt-parent = <&gpio5>;
interrupts = <25 IRQ_TYPE_LEVEL_LOW>;
};
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add onsemi,pca9654 which is also compatible with the nxp,pca9524 as it
is an 8bit expander with an interrupt output.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I missed to convert this driver properly to use .parent to
point to the parent device. ARMv7 multiplatform would not
compile.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio-samsung driver is special in the sense that it
interacts directly in multiple ways with the legacy platform
code for the s3c24xx and s3c64xx platforms. In contrast,
all devicetree based machines for Samsung, including the
ones on those two SoC families use a different driver.
The header files that define the interface between the platform
code and the gpio driver are not visible when building a
kernel for ARCH_MULTIPLATFORM, which prevents us from
turning on this option for s3c64xx.
To work around this, we now move the driver back into platform
code, from where it was originally moved to as part of commit
1b39d5f2cc ("gpio/samsung: gpio-samsung.c to support
Samsung GPIOs").
The long-term plan for this driver would be to remove it
entirely, after all Samsung machines have been converted
over to boot from DT, but there is currently no timeline
for when that might happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
The ACCES 104-IDI-48 family of PC/104 utility boards feature 48
individually optically isolated digital inputs. Enabled inputs feature
change-of-state detection capability; if change-of-state detection is
enabled, an interrupt is fired off if a change of input level
(low-to-high or high-to-low) is detected. Change-of-state IRQs are
enabled/disabled on 8-bit boundaries, for a total of six boundaries.
This driver provides GPIO and IRQ support for these 48 channels of
digital input. The base port address for the device may be configured
via the idi_48_base module parameter. The interrupt line number for the
device may be configured via the idi_48_irq module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Nizam Haider <nijamh@cdac.in>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IRQ should be disabled on device probe so that the device IRQ is in a
known starting state. If IRQ is not disabled, interrupts may be reported
as handled by the IRQ handler, despite no irq_unmask calls made by the
user.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Originally OMAP MPUIO GPIO irqchip was implemented using Generic irq
chip, but after set of reworks Generic irq chip code was replaced by
common OMAP GPIO implementation and finally removed by
commit d2d05c65c4 ("gpio: omap: Fix regression for MPUIO interrupts").
Unfortunately, above commit left .irq_mask/unmask callbacks assigned
as below for MPUIO GPIO case:
irqc->irq_mask = irq_gc_mask_set_bit;
irqc->irq_unmask = irq_gc_mask_clr_bit;
This now causes boot failure on OMAP1 platforms, after
commit 450fa54cfd ("gpio: omap: convert to use generic irq handler")
which forces these callbacks to be called during GPIO IRQs mapping
from gpiochip_irq_map:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 75 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.4.0-rc1-e3-los_afe0c+-00002-g25379c0-dirty #1
Hardware name: Amstrad E3 (Delta)
task: c1836000 ti: c1838000 task.ti: c1838000
PC is at irq_gc_mask_set_bit+0x1c/0x60
LR is at __irq_do_set_handler+0x118/0x15c
pc : [<c004848c>] lr : [<c0047d4c>] psr: 600000d3
sp : c1839c90 ip : c1862c64 fp : c1839c9c
r10: 00000000 r9 : c0411950 r8 : c0411bbc
r7 : 00000000 r6 : c185c310 r5 : c00444e8 r4 : c185c300
r3 : c1854b50 r2 : 00000000 r1 : 00000000 r0 : c185c310
Flags: nZCv IRQs off FIQs off Mode SVC_32 ISA ARM Segment kernel
Control: 0000317f Table: 10004000 DAC: 00000057
Process swapper (pid: 1, stack limit = 0xc1838190)
Stack: (0xc1839c90 to 0xc183a000)
[...]
Backtrace:
[<c0048470>] (irq_gc_mask_set_bit) from [<c0047d4c>] (__irq_do_set_handler+0x118/0x15c)
[<c0047c34>] (__irq_do_set_handler) from [<c0047dd4>] (__irq_set_handler+0x44/0x5c)
r6:00000000 r5:c00444e8 r4:c185c300
[<c0047d90>] (__irq_set_handler) from [<c0047e1c>] (irq_set_chip_and_handler_name+0x30/0x34)
r7:00000050 r6:00000000 r5:c00444e8 r4:00000050
[<c0047dec>] (irq_set_chip_and_handler_name) from [<c01b345c>] (gpiochip_irq_map+0x3c/0x8c)
r7:00000050 r6:00000000 r5:00000050 r4:c1862c64
[<c01b3420>] (gpiochip_irq_map) from [<c0049670>] (irq_domain_associate+0x7c/0x1c4)
r5:c185c310 r4:c185cb00
[<c00495f4>] (irq_domain_associate) from [<c0049894>] (irq_domain_add_simple+0x98/0xc0)
r8:c0411bbc r7:c185cb00 r6:00000050 r5:00000010 r4:00000001
[<c00497fc>] (irq_domain_add_simple) from [<c01b3328>] (_gpiochip_irqchip_add+0x64/0x10c)
r7:c1862c64 r6:c0419280 r5:c1862c64 r4:c1854b50
[<c01b32c4>] (_gpiochip_irqchip_add) from [<c01b79f4>] (omap_gpio_probe+0x2fc/0x63c)
r5:c1854b50 r4:c1862c10
[<c01b76f8>] (omap_gpio_probe) from [<c01fcf58>] (platform_drv_probe+0x2c/0x64)
r10:00000000 r9:c03e45e8 r8:00000000 r7:c0419294 r6:c0411984 r5:c0419294
r4:c0411950
[<c01fcf2c>] (platform_drv_probe) from [<c01fb668>] (really_probe+0x160/0x29c)
Hence, fix it by remove obsolete callbacks assignment. After this
change omap_gpio_mask_irq()/omap_gpio_unmask_irq() will be used
for MPUIO IRQs masking, but this now happens anyway from
omap_gpio_irq_startup/shutdown().
Cc: Tony Lindgren <tony@atomide.com>
Fixes: commit d2d05c65c4 ("gpio: omap: Fix regression for MPUIO interrupts")
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit f4d566a8a0e6 ("gpio: change member .dev to .parent") changes
member of gpiochip from .dev to .parent. Update the corresponding
comment.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit c0017ed719 ("gpio: Introduce gpio descriptor 'name'") causes
OOPS on boot on LPC32xx boards:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
CPU: 0 PID: 1 Comm: swapper Not tainted 4.3.0+ #707
Hardware name: LPC32XX SoC (Flattened Device Tree)
task: c381baa0 ti: c381e000 task.ti: c381e000
PC is at strcmp+0x10/0x40
LR is at gpiochip_add+0x3d0/0x4d4
pc : [<>] lr : [<>] psr: a0000093
sp : c381fd60 ip : c381fd70 fp : c381fd6c
[snip]
Backtrace:
[<>] (strcmp) from [<>] (gpiochip_add+0x3d0/0x4d4)
[<>] (gpiochip_add) from [<>] (lpc32xx_gpio_probe+0x44/0x60)
[<>] (lpc32xx_gpio_probe) from [<>] (platform_drv_probe+0x40/0x8c)
[<>] (platform_drv_probe) from [<>] (driver_probe_device+0x110/0x294)
[<>] (driver_probe_device) from [<>] (__driver_attach+0x70/0x94)
[<>] (__driver_attach) from [<>] (bus_for_each_dev+0x74/0x98)
[<>] (bus_for_each_dev) from [<>] (driver_attach+0x20/0x28)
[<>] (driver_attach) from [<>] (bus_add_driver+0xd4/0x1f0)
[<>] (bus_add_driver) from [<>] (driver_register+0xa4/0xe8)
[<>] (driver_register) from [<>] (__platform_driver_register+0x38/0x4c)
[<>] (__platform_driver_register) from [<>] (lpc32xx_gpio_driver_init+0x18/0x20)
[<>] (lpc32xx_gpio_driver_init) from [<>] (do_one_initcall+0x108/0x1c8)
[<>] (do_one_initcall) from [<>] (kernel_init_freeable+0x10c/0x1d4)
[<>] (kernel_init_freeable) from [<>] (kernel_init+0x10/0xec)
[<>] (kernel_init) from [<>] (ret_from_fork+0x14/0x24)
This is caused by the fact that at the moment some GPIO names are set
to NULL, there is a hole in linear representation of one GPI bank, see
drivers/gpio/gpio-lpc32xx.c / gpi_p3_names[] for details.
The same problem most probably affects also gpio-cs5535.c, see
cs5535_gpio_names[].
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prevent confusion, and to match the existing coding style used in
other GPIO drivers, symbol names within the 104-idio-16 GPIO driver
should be lowercase.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to check if number of gpio is positive if there is no
such check in devicetree or acpi or whatever called before
gpiochip_add.
I suppose that devicetree and acpi do not allow insert gpiochip
with zero number but I do not know if it is enough to ignore
this check in gpiochip_add.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are limitations for the current checker:
1. Could not check the overlap if the new gpiochip is the secondly
gpiochip.
2. Could not check the overlap if the new gpiochip is overlap
with the left of gpiochip. E.g. if we insert [c, d] between
[a,b] and [e, f], and e >= c + d, it will successful even if
c < a + b.
3. Allow overlap of base of different gpiochip.
This patch fix these issues by checking the overlap of both right and
left gpiochip in the same loop statement.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
[Tweaked to remove unnecessary ret variable]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The commit f881bab038 ("gpio: keep the GPIO line names internal")
change the error to warning in gpiochip_set_desc_names. Update the
comment accordingly.
Signed-off-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is a second attempt at what was previously in commit
6c7e660a27 ("gpio: pxa: set initcall level to module init").
The goal is the same : enable gpio & pinctrl driver to work
together. As pinctrl driver will be initialized at device level, the
gpio should be as well, so that the deferring mechanism is honored.
Yet this patch should also respect the legacy platforms, so the set of
constraints is :
- in legacy platforms (ie. non dt), gpio_[gs]et_*() should be available
for machine code => core initcall
- in new platforms (ie. dt based), pinctrl will be available and no
machine code => device initcall
In order to fullfill all these constraints, the initcall level is either
postcore for non devicetree platforms, and device for devicetree platforms.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should not fall back to the legacy unnamed gpio lookup style if the
driver requests gpios with different names, because we'll give out the same
gpio twice. Let's keep track of the names that were used for the device and
only do the fallback for the first name used.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 series offers Change-of-State detection interrupt
functionality; if Change-of-State detection is enabled, an interrupt is
fired off if any input line changes state (i.e. goes from low to high,
or from high to low). This patch adds support to handle these interrupts
and allows the user to mask which GPIO lines are affected. The interrupt
line number for the device may be set via the idio_16_irq module
parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The name .dev in a struct is normally reserved for a struct device
that is let us say a superclass to the thing described by the struct.
struct gpio_chip stands out by confusingly using a struct device *dev
to point to the parent device (such as a platform_device) that
represents the hardware. As we want to give gpio_chip:s real devices,
this is not working. We need to rename this member to parent.
This was done by two coccinelle scripts, I guess it is possible to
combine them into one, but I don't know such stuff. They look like
this:
@@
struct gpio_chip *var;
@@
-var->dev
+var->parent
and:
@@
struct gpio_chip var;
@@
-var.dev
+var.parent
and:
@@
struct bgpio_chip *var;
@@
-var->gc.dev
+var->gc.parent
Plus a few instances of bgpio that I couldn't figure out how
to teach Coccinelle to rewrite.
This patch hits all over the place, but I *strongly* prefer this
solution to any piecemal approaches that just exercise patch
mechanics all over the place. It mainly hits drivers/gpio and
drivers/pinctrl which is my own backyard anyway.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Alek Du <alek.du@intel.com>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The tegra gpio driver creates the debugfs entry irrespective of
whether the device exists or not. This is enabled on an arm64_defconfig
and leaves an entry in debugfs on all platforms where it is not
useful. This patch fixes the issue by creating the entry only when
a device exists.
Signed-off-by: Suzuki K. Poulose <suzuki.poulose@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
Reported-by: coverity (CID 1130700)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later at line 199:
priv->flags = of_id->data;
Reported-by: coverity (CID 1324140)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_match_device could return NULL, and so cause a NULL pointer
dereference later at line 132:
priv->flags = (uintptr_t) of_id->data;
Reported-by: coverity (CID 1324141)
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The asm-generic changes for 4.4 are mostly a series from Christoph Hellwig
to clean up various abuses of headers in there. The patch to rename the
io-64-nonatomic-*.h headers caused some conflicts with new users, so I
added a workaround that we can remove in the next merge window.
The only other patch is a warning fix from Marek Vasut
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=dQKG
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic cleanups from Arnd Bergmann:
"The asm-generic changes for 4.4 are mostly a series from Christoph
Hellwig to clean up various abuses of headers in there. The patch to
rename the io-64-nonatomic-*.h headers caused some conflicts with new
users, so I added a workaround that we can remove in the next merge
window.
The only other patch is a warning fix from Marek Vasut"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
asm-generic: temporarily add back asm-generic/io-64-nonatomic*.h
asm-generic: cmpxchg: avoid warnings from macro-ized cmpxchg() implementations
gpio-mxc: stop including <asm-generic/bug>
n_tracesink: stop including <asm-generic/bug>
n_tracerouter: stop including <asm-generic/bug>
mlx5: stop including <asm-generic/kmap_types.h>
hifn_795x: stop including <asm-generic/kmap_types.h>
drbd: stop including <asm-generic/kmap_types.h>
move count_zeroes.h out of asm-generic
move io-64-nonatomic*.h out of asm-generic
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface)
and a few fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2)
support along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated
by the specification) to avoid confusion on systems with more than
255 logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges
on x86 and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when
it has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume
handling in some cases and the changes include a couple of users
of it (the i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up
the system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that
code (Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common
cpufreq policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states
range to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization
to make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=1gaH
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"Quite a new features are included this time.
First off, the Collaborative Processor Performance Control interface
(version 2) defined by ACPI will now be supported on ARM64 along with
a cpufreq frontend for CPU performance scaling.
Second, ACPI gets a new infrastructure for the early probing of IRQ
chips and clock sources (along the lines of the existing similar
mechanism for DT).
Next, the ACPI core and the generic device properties API will now
support a recently introduced hierarchical properties extension of the
_DSD (Device Specific Data) ACPI device configuration object. If the
ACPI platform firmware uses that extension to organize device
properties in a hierarchical way, the kernel will automatically handle
it and make those properties available to device drivers via the
generic device properties API.
It also will be possible to build the ACPICA's AML interpreter
debugger into the kernel now and use that to diagnose AML-related
problems more efficiently. In the future, this should make it
possible to single-step AML execution and do similar things.
Interesting stuff, although somewhat experimental at this point.
Finally, the PM core gets a new mechanism that can be used by device
drivers to distinguish between suspend-to-RAM (based on platform
firmware support) and suspend-to-idle (or other variants of system
suspend the platform firmware is not involved in) and possibly
optimize their device suspend/resume handling accordingly.
In addition to that, some existing features are re-organized quite
substantially.
First, the ACPI-based handling of PCI host bridges on x86 and ia64 is
unified and the common code goes into the ACPI core (so as to reduce
code duplication and eliminate non-essential differences between the
two architectures in that area).
Second, the Operating Performance Points (OPP) framework is
reorganized to make the code easier to find and follow.
Next, the cpufreq core's sysfs interface is reorganized to get rid of
the "primary CPU" concept for configurations in which the same
performance scaling settings are shared between multiple CPUs.
Finally, some interfaces that aren't necessary any more are dropped
from the generic power domains framework.
On top of the above we have some minor extensions, cleanups and bug
fixes in multiple places, as usual.
Specifics:
- ACPICA update to upstream revision 20150930 (Bob Moore, Lv Zheng).
The most significant change is to allow the AML debugger to be
built into the kernel. On top of that there is an update related
to the NFIT table (the ACPI persistent memory interface) and a few
fixes and cleanups.
- ACPI CPPC2 (Collaborative Processor Performance Control v2) support
along with a cpufreq frontend (Ashwin Chaugule).
This can only be enabled on ARM64 at this point.
- New ACPI infrastructure for the early probing of IRQ chips and
clock sources (Marc Zyngier).
- Support for a new hierarchical properties extension of the ACPI
_DSD (Device Specific Data) device configuration object allowing
the kernel to handle hierarchical properties (provided by the
platform firmware this way) automatically and make them available
to device drivers via the generic device properties interface
(Rafael Wysocki).
- Generic device properties API extension to obtain an index of
certain string value in an array of strings, along the lines of
of_property_match_string(), but working for all of the supported
firmware node types, and support for the "dma-names" device
property based on it (Mika Westerberg).
- ACPI core fix to parse the MADT (Multiple APIC Description Table)
entries in the order expected by platform firmware (and mandated by
the specification) to avoid confusion on systems with more than 255
logical CPUs (Lukasz Anaczkowski).
- Consolidation of the ACPI-based handling of PCI host bridges on x86
and ia64 (Jiang Liu).
- ACPI core fixes to ensure that the correct IRQ number is used to
represent the SCI (System Control Interrupt) in the cases when it
has been re-mapped (Chen Yu).
- New ACPI backlight quirk for Lenovo IdeaPad S405 (Hans de Goede).
- ACPI EC driver fixes (Lv Zheng).
- Assorted ACPI fixes and cleanups (Dan Carpenter, Insu Yun, Jiri
Kosina, Rami Rosen, Rasmus Villemoes).
- New mechanism in the PM core allowing drivers to check if the
platform firmware is going to be involved in the upcoming system
suspend or if it has been involved in the suspend the system is
resuming from at the moment (Rafael Wysocki).
This should allow drivers to optimize their suspend/resume handling
in some cases and the changes include a couple of users of it (the
i8042 input driver, PCI PM).
- PCI PM fix to prevent runtime-suspended devices with PME enabled
from being resumed during system suspend even if they aren't
configured to wake up the system from sleep (Rafael Wysocki).
- New mechanism to report the number of a wakeup IRQ that woke up the
system from sleep last time (Alexandra Yates).
- Removal of unused interfaces from the generic power domains
framework and fixes related to latency measurements in that code
(Ulf Hansson, Daniel Lezcano).
- cpufreq core sysfs interface rework to make it handle CPUs that
share performance scaling settings (represented by a common cpufreq
policy object) more symmetrically (Viresh Kumar).
This should help to simplify the CPU offline/online handling among
other things.
- cpufreq core fixes and cleanups (Viresh Kumar).
- intel_pstate fixes related to the Turbo Activation Ratio (TAR)
mechanism on client platforms which causes the turbo P-states range
to vary depending on platform firmware settings (Srinivas
Pandruvada).
- intel_pstate sysfs interface fix (Prarit Bhargava).
- Assorted cpufreq driver (imx, tegra20, powernv, integrator) fixes
and cleanups (Bai Ping, Bartlomiej Zolnierkiewicz, Shilpasri G
Bhat, Luis de Bethencourt).
- cpuidle mvebu driver cleanups (Russell King).
- OPP (Operating Performance Points) framework code reorganization to
make it more maintainable (Viresh Kumar).
- Intel Broxton support for the RAPL (Running Average Power Limits)
power capping driver (Amy Wiles).
- Assorted power management code fixes and cleanups (Dan Carpenter,
Geert Uytterhoeven, Geliang Tang, Luis de Bethencourt, Rasmus
Villemoes)"
* tag 'pm+acpi-4.4-rc1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (108 commits)
cpufreq: postfix policy directory with the first CPU in related_cpus
cpufreq: create cpu/cpufreq/policyX directories
cpufreq: remove cpufreq_sysfs_{create|remove}_file()
cpufreq: create cpu/cpufreq at boot time
cpufreq: Use cpumask_copy instead of cpumask_or to copy a mask
cpufreq: ondemand: Drop unnecessary locks from update_sampling_rate()
PM / Domains: Merge measurements for PM QoS device latencies
PM / Domains: Don't measure ->start|stop() latency in system PM callbacks
PM / clk: Fix broken build due to non-matching code and header #ifdefs
ACPI / Documentation: add copy_dsdt to ACPI format options
ACPI / sysfs: correctly check failing memory allocation
ACPI / video: Add a quirk to force native backlight on Lenovo IdeaPad S405
ACPI / CPPC: Fix potential memory leak
ACPI / CPPC: signedness bug in register_pcc_channel()
ACPI / PAD: power_saving_thread() is not freezable
ACPI / PM: Fix incorrect wakeup IRQ setting during suspend-to-idle
ACPI: Using correct irq when waiting for events
ACPI: Use correct IRQ when uninstalling ACPI interrupt handler
cpuidle: mvebu: disable the bind/unbind attributes and use builtin_platform_driver
cpuidle: mvebu: clean up multiple platform drivers
...
Pull irq updates from Thomas Gleixner:
"The irq departement delivers:
- Rework the irqdomain core infrastructure to accomodate ACPI based
systems. This is required to support ARM64 without creating
artificial device tree nodes.
- Sanitize the ACPI based ARM GIC initialization by making use of the
new firmware independent irqdomain core
- Further improvements to the generic MSI management
- Generalize the irq migration on CPU hotplug
- Improvements to the threaded interrupt infrastructure
- Allow the migration of "chained" low level interrupt handlers
- Allow optional force masking of interrupts in disable_irq[_nosysnc]
- Support for two new interrupt chips - Sigh!
- A larger set of errata fixes for ARM gicv3
- The usual pile of fixes, updates, improvements and cleanups all
over the place"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (71 commits)
Document that IRQ_NONE should be returned when IRQ not actually handled
PCI/MSI: Allow the MSI domain to be device-specific
PCI: Add per-device MSI domain hook
of/irq: Use the msi-map property to provide device-specific MSI domain
of/irq: Split of_msi_map_rid to reuse msi-map lookup
irqchip/gic-v3-its: Parse new version of msi-parent property
PCI/MSI: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Use of_msi_get_domain instead of open-coded "msi-parent" parsing
of/irq: Add support code for multi-parent version of "msi-parent"
irqchip/gic-v3-its: Add handling of PCI requester id.
PCI/MSI: Add helper function pci_msi_domain_get_msi_rid().
of/irq: Add new function of_msi_map_rid()
Docs: dt: Add PCI MSI map bindings
irqchip/gic-v2m: Add support for multiple MSI frames
irqchip/gic-v3: Fix translation of LPIs after conversion to irq_fwspec
irqchip/mxs: Add Alphascale ASM9260 support
irqchip/mxs: Prepare driver for hardware with different offsets
irqchip/mxs: Panic if ioremap or domain creation fails
irqdomain: Documentation updates
irqdomain/msi: Use fwnode instead of of_node
...
- Relax dependencies on SPI_MASTER for drivers in the SPI menu
that already has this dependency.
- Move out the expander that would be hidden for I2C access if
SPI_MASTER was not selected. Tentatively create a separate
menu for this.
- Move the ZX SoC driver to memory-mapped drivers, this must be
a mistake and only worked because the system has an SPI master
enabled at the same time.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C expander menu already depends on I2C, drop subdependecies
on individual drivers. Keep the instances of depends on I2C=y
though, so these are still restricted to the compiled-in case.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Port-mapped I/O depends on X86 already, so individual drivers need
not specify this dependency.
Suggested-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In Microsoft Surface3 the GPIO detecting lid state is shared between GPIO
event and operation region. Below is simplied version of the DSDT from
Surface3 including relevant parts:
Scope (GPO0)
{
Name (_AEI, ResourceTemplate ()
{
GpioInt (Edge, ActiveBoth, Shared, PullNone, 0x0000,
"\\_SB.GPO0", 0x00, ResourceConsumer, ,
)
{ // Pin list
0x004C
}
})
OperationRegion (GPOR, GeneralPurposeIo, Zero, One)
Field (GPOR, ByteAcc, NoLock, Preserve)
{
Connection (
GpioIo (Shared, PullNone, 0x0000, 0x0000,
IoRestrictionNone, "\\_SB.GPO0", 0x00,
ResourceConsumer,,)
{ // Pin list
0x004C
}
),
HELD, 1
}
Method (_E4C, 0, Serialized) // _Exx: Edge-Triggered GPE
{
If ((HELD == One))
{
^^LID.LIDB = One
}
Else
{
^^LID.LIDB = Zero
Notify (LID, 0x80) // Status Change
}
Notify (^^PCI0.SPI1.NTRG, One) // Device Check
}
}
When GPIO 0x4c changes we call ASL method _E4C which tries to read HELD
field (the same GPIO). This triggers following error on the console:
ACPI Error: Method parse/execution failed [\_SB.GPO0._E4C]
(Node ffff88013f4b4438), AE_ERROR (20150930/psparse-542)
The error happens because ACPI GPIO operation region handler
(acpi_gpio_adr_space_handler()) tries to acquire the very same GPIO which
returns an error (-EBUSY) because the GPIO is already reserved for the GPIO
event.
Fix this so that we "borrow" the event GPIO if we find the GPIO belongs to
an event. Allow this only for GPIOs that are read.
To be able to go through acpi_gpio->events list for operation region access
we need to make sure the list is properly initialized whenever GPIO chip is
registered.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=106571
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create a Kconfig submenu for drivers using X86 port-mapped I/O
and depend on X86 for this.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: Andreas Bofjall <andreas@gazonk.org>
Cc: Diego Elio Pettenò <flameeyes@flameeyes.eu>
Cc: Daniel Krueger <daniel.krueger@systec-electronic.com>
Cc: Bruno Randolf <br1@einfach.org>
Cc: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver does not have any real architecture dependencies. To avoid
listing each architecture that might use this driver on some
FPGA-enabled platform, drop these dependencies.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Acked-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Returning an error instead of NULL in bgpio_map if
platform_get_resource_byname does not find a resource was introduced with
commit cf3f2a2c8b ("gpio: generic: improve error handling in bgpio_map").
This results in several qemu runtime failures with default and non-default
configurations, if attempts are made to boot from mmcblk0. Examples for
failures with multi_v7_defconfig are
Machine: vexpress-a9 dtb: vexpress-v2p-ca9
Machine: vexpress-a15 dtb: vexpress-v2p-ca15-tc1
Crash:
VFS: Cannot open root device "mmcblk0" or unknown-block(0,0): error -6
Please append a correct "root=" boot option; here are the available partitions:
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Looking into the code, always returning an error if bgpio_map fails
does not appear to make much sense, since the code in bgpio_setup_io
specifically supports some of the resources to be NULL.
Fixes: cf3f2a2c8b ("gpio: generic: improve error handling in bgpio_map")
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 family of PC/104 utility boards feature 16
optically isolated inputs and 16 optically isolated FET solid state
outputs. This driver provides GPIO support for these 32 channels of
digital I/O. Change-of-State detection interrupts are not supported.
GPIO 0-15 correspond to digital outputs 0-15, while GPIO 16-31
correspond to digital inputs 0-15. The base port address for the device
may be set via the idio_16_base module parameter.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
