Fix build fault when CONFIG_HWMON is a module, and CONFIG_VIDEO_I2C
as builtin. This is due to 'imply hwmon' in the respective Kconfig.
Issue build log:
ld: drivers/media/i2c/video-i2c.o: in function `amg88xx_hwmon_init':
video-i2c.c:(.text+0x2e1): undefined reference to `devm_hwmon_device_register_with_info
Cc: rdunlap@infradead.org
Fixes: acbea67989 (media: video-i2c: add hwmon support for amg88xx)
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As of `s5c73m3.h` the auto focus cluster in `s5c73m3_ctrls` has 5 and not 6
controls.
Signed-off-by: Sebastian Gross <sebastian.gross@emlix.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The pad is now checked by v4l2_subdev_call_wappers
call_g_frame_interval-> check_frame_interval-> check_pad
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1
The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The debug output for tvp5150_selmux() isn't really intuitive. Register
values are printed decimal formatted and the input/output driver states
are printed as enum. Even more the "normal" output enum mapps to zero so
a active output will printing output=0 and a inactive output=1.
Change this by brinting the register values hex formatted and the states
as more readable string.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video
data and is able to auto-detect the input signal. The auto-detection
does not work if the connector does not receive an input signal and the
tvp5150 might not be configured correctly. This misconfiguration leads
into wrong decoded video streams if the tvp5150 gets powered on before
the video signal is present.
Limit the supported sdtv standards according to the actual selected
connector to avoid a misconfiguration.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Bring the device into a working state upon a open/close call. Currently
this involves only the interrupt enable/disable process but can be
extended in the future.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the driver notifies internal subdevs if the signal is locked
or not. This information is also useful for userpace applications e.g. to
switch to another input device upon a signal lost event.
This commit adds the support for the userspace to subscribe to the
V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
As documented in [1] the runtime-pm ops are used to set the device into
a fully 'workable' state. Therefore it can be used to enable or disable
the irqs.
[1] https://www.kernel.org/doc/html/latest/power/runtime_pm.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
There are several debug prints in the tvp5150_parse_dt() function, which
do not print the prefix, because the v4l2_subdev is not initialized, yet.
Initialize the v4l2_subdev before parsing the device tree to fix the
debug messages.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Since commit 10d5509c8d ("[media] v4l2: remove g/s_crop from video ops")
the 'which' field for set/get_selection must be FORMAT_ACTIVE. There is
no way to try different selections. The patch adds a helper function to
select the correct selection memory space (sub-device file handle or
driver state) which will be set/returned.
The selection rectangle is updated if the format is FORMAT_ACTIVE and
the rectangle position and/or size differs from the current set
rectangle.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently a local copy of sel->r is made and adapted to the hardware
constraints. After the adaption the value is applied to the hardware but
the driver forgot to reflect the adapted value to the user space.
Drop the local copy and work directly on the requested rectangle
instead to fix this.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch adds the of_graph support to describe the tvp input connections.
Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result
of discussion [1],[2] the device-tree maps these ports 1:1. Look at the
Documentation for more information. Since the TVP5150 is a converter/bridge
the device-tree must contain at least 1-input and 1-output port. The
mc-connectors and mc-links are only created if the device-tree contains the
corresponding connector nodes. If more than one connector is available the
media_entity_operations.link_setup() callback ensures that only one
connector is active.
[1] https://www.spinics.net/lists/linux-media/msg138545.html
[2] https://www.spinics.net/lists/linux-media/msg138546.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Commit f7b4b54e63 ("[media] tvp5150: add HW input connectors support")
added input signals support for the tvp5150, but the approach was found
to be incorrect so the corresponding DT binding commit 82c2ffeb21
("[media] tvp5150: document input connectors DT bindings") was reverted.
This left the driver with an undocumented (and wrong) DT parsing logic,
so lets get rid of this code as well until the input connectors support
is implemented properly.
It's a partial revert due other patches added on top of mentioned commit
not allowing the commit to be reverted cleanly anymore. But all the code
related to the DT parsing logic and input entities creation are removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[m.felsch@pengutronix.de: rm TVP5150_INPUT_NUM define]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
include/media/i2c/smiapp.h was meant to serve systems where the sensor is
enumerated through platform data. That's no longer necessary, hopefully
not even in out-of-tree use cases. Move the definitions to the appropriate
headers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Combine the two trivial functions reading limits into one. Also rename
smiapp_get_all_limits() as smiapp_read_all_smia_limits().
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Instead of direct array access, turn accessing limit information into a
function. Going forward, more elaborate CCS limits will replace most SMIA
limits, and conversion will be less complicated this way.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use get_unaligned_be* and put_unaligned_be* functions to convert register
values to CPU endianness. Consequently, two instances of BUG() are
removed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use the only8 boolean to determine whether 8-bit access is required for
reading.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Adds a driver for the 8MPix Sony IMX219 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
8MPix @ 15fps, 1080P @ 30fps (cropped FOV), and 1640x1232 (2x2 binned)
@ 30fps are currently supported.
[Sakari Ailus: make imx219_check_hwcfg static]
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
'GRABBER' is a weird name, all other types map to the /dev
device names. Rename to 'VIDEO' to be consistent with the
other types.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add a init_cfg pad operation so that configurations allocated with
v4l2_subdev_alloc_pad_config() are initialized.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The mt9v111_def_fmt structure is only copied into another structure,
so make it const.
The opportunity for this change was found using Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Acked-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This driver supports both the mt9v032 (color) and the mt9v022 (mono)
sensors. Depending on which sensor is used, the format from the sensor is
different. The format.code inside the dev struct holds this information.
The enum mbus and enum frame sizes need to take into account both type of
sensors, not just the color one. To solve this, use the format.code in
these functions instead of the hardcoded bayer color format (which is only
used for mt9v032).
[Sakari Ailus: rewrapped commit message]
Suggested-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The variable _rate is by ov5640_compute_sys_clk() which returns
zero if the PLL exceeds 1GHz. Unfortunately, the check to see
if the max PLL1 output is checking 'rate' and not '_rate' and
'rate' does not ever appear to be 0.
This patch changes the check against the returned value of
'_rate' to determine if the PLL1 output exceeds 1GHz.
Fixes: aa2882481c ("media: ov5640: Adjust the clock based on the expected rate")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Currently the various modes are placed into a table, but when
ov5640_find_mode is called, it has to double check whether
or not the requested framerate is tolerated by the mode.
The determination is based on checking hact, vact, and frame rate.
Only 640x480 is allowed at 60fps and QSXGA is limited to 15fps, but
as the number of permitted frame rates change, this will begin to
add more and more complexity to the check.
This patch simplifies the check by adding the max framerate
allowed for each mode into the table of modes. It then compares
the requested framerate to the max permitted in the mode's table.
This reduces the number of comparisions to one down from three
at run-time.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
If there was an error in starting streaming, put the runtime usage count
of the device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Instead of keeping track of the power state ourselves, let runtime PM
handle it.
This also splits handling controls between side effect management and
writing the new configuration to the sensor's registers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
The AD7611 chip supports the same Deep Color Mode settings as the AD7604.
This change extends support for this feature to the AD7611 by adding a
wrapper function for the `read_hdmi_pixelclock` hook and adding the same
frequency adjustment logic.
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enclose multiple macro parameters in parentheses in order to
make such macros safer and fix the Clang warning below:
drivers/media/i2c/adv748x/adv748x-afe.c:452:12: warning: operator '?:'
has lower precedence than '|'; '|' will be evaluated first
[-Wbitwise-conditional-parentheses]
ret = sdp_clrset(state, ADV748X_SDP_FRP, ADV748X_SDP_FRP_MASK, enable
? ctrl->val - 1 : 0);
Fixes: 3e89586a64 ("media: i2c: adv748x: add adv748x driver")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
This patch corrects the SPDX License Identifier style
in header files related to I2C controlled media codec drivers.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46
and some manual changes.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initialize ret to 0 to fix this smatch error:
drivers/media/i2c/ov6650.c:853 ov6650_video_probe() error: uninitialized symbol 'ret'.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a V4L2 sub-device driver for Hynix Hi-556 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 2592x1944 at 30FPS
+ 1296x972 at 30FPS
[sakari.ailus@linux.intel.com: Remove MEDIA_CAMERA_SUPPORT from Kconfig dependencies]
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Replace F* word with something less offensive.
[hverkuil: dropped 'Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")' tag since nothing was broken]
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Don't populate the array input_vals on the stack but instead make it
static. Makes the object code smaller by 106 bytes.
Before:
text data bss dec hex filename
11744 3536 128 15408 3c30 drivers/media/i2c/vpx3220.o
After:
text data bss dec hex filename
11574 3600 128 15302 3bc6 drivers/media/i2c/vpx3220.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
We added two new error paths to smiapp_start_streaming(), but we can't
return directly without dropping the "sensor->mutex" lock.
Fixes: f8c4352c1b ("media: smiapp: Move binning configuration to streaming start")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Rename the confusingly named smiapp_update_mode() function as
smiapp_pll_blanking_update(). The function is used to calculate new PLL
and blanking configuration after binning or scaling configuration has been
changed.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Earlier it was possible that the parts of the driver that assumed runtime
PM was enabled were being called before runtime PM was enabled in the
driver's probe function. So enable runtime PM before registering the
sub-device.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use non-binned limits when binning is disabled and binned when they're
enabled.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The sensor configuration since it was previously powered off was not
changed, so no need to update the PLL configuration etc. What is necessary
though is to re-apply the configuration to the sensor's registers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Only write the binning configuration at stream start. It has no effect
otherwise.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The driver implementation assumed the binning limits could change
dynamically based on the binning configuration. This is not actually the
case; these limits are static and suitable to be used with all binning
configurations but possibly not optimal limit for many of those
configurations.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Destroy the mutex initialised by the driver in probe.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The interface supports probing for the NVM size but this was not
implemented in the driver. Do that now.
This will also make nokia,nvm-size property redundant.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
