Convert the per cpu topology cpu masks to a per cpu variable.
At least for machines which do have less possible cpus than NR_CPUS this can
save a bit of memory (z/VM: max 64 vs 512 for performance_defconfig).
This reduces the kernel image size by 100k.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
There is no reason to initialize the topology cpu masks already while
setup_arch() is being called. It is sufficient to initialize the masks
before the scheduler becomes SMP aware.
Therefore a pre-SMP initcall aka early_initcall is suffucient.
This also allows to convert the cpu_topology array into a per cpu
variable with a later patch. Without this patch this wouldn't be
possible since the per cpu memory areas are not allocated while setup_arch
is executed.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The multi-threading facility is introduced with the z13 processor family.
This patch adds code to detect the multi-threading facility. With the
facility enabled each core will surface multiple hardware threads to the
system. Each hardware threads looks like a normal CPU to the operating
system with all its registers and properties.
The SCLP interface reports the SMT topology indirectly via the maximum
thread id. Each reported CPU in the result of a read-scp-information
is a core representing a number of hardware threads.
To reflect the reduced CPU capacity if two hardware threads run on a
single core the MT utilization counter set is used to normalize the
raw cputime obtained by the CPU timer deltas. This scaled cputime is
reported via the taskstats interface. The normal /proc/stat numbers
are based on the raw cputime and are not affected by the normalization.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We replace the old way to configure the scheduler topology with a new method
which enables a platform to declare additionnal level (if needed).
We still have a default topology table definition that can be used by platform
that don't want more level than the SMT, MC, CPU and NUMA ones. This table can
be overwritten by an arch which either wants to add new level where a load
balance make sense like BOOK or powergating level or wants to change the flags
configuration of some levels.
For each level, we need a function pointer that returns cpumask for each cpu,
a function pointer that returns the flags for the level and a name. Only flags
that describe topology, can be set by an architecture. The current topology
flags are:
SD_SHARE_CPUPOWER
SD_SHARE_PKG_RESOURCES
SD_NUMA
SD_ASYM_PACKING
Then, each level must be a subset on the next one. The build sequence of the
sched_domain will take care of removing useless levels like those with 1 CPU
and those with the same CPU span and no more relevant information for
load balancing than its children.
Signed-off-by: Vincent Guittot <vincent.guittot@linaro.org>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Reviewed-by: Preeti U Murthy <preeti@linux.vnet.ibm.com>
Reviewed-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Jason Low <jason.low2@hp.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux390@de.ibm.com
Cc: linux-ia64@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Link: http://lkml.kernel.org/r/1397209481-28542-2-git-send-email-vincent.guittot@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mainly merge all different per-cpu arrays into a single array which
holds all topology information per logical cpu.
Also fix the broken core vs socket variable naming and simplify the
locking a bit.
When running in environments without topology information also
invent book, socket and core ids, so that not all ids are zero.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current topology code confuses core id vs physical package id.
In other words /sys/devices/system/cpu/cpuX/topology/core_id
displays the physical_package_id (aka socket id) instead of the
core id.
The physical_package_id sysfs attribute always displays "-1"
instead of the socket id.
Fix this mix-up with a small patch which defines and initializes
topology_physical_package_id correctly and fixes the broken
core id handling.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The cpu polarization member is the only per cpu state that is not part
of the pcpu structure. So add it there and have everything in one place.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Any change to sysinfo.h causes a whole kernel recompile since sysinfo.h is
included by topology.h, which again is used nearly everywhere.
So remove that include and add a forward declaration instead.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Increase cpu topology change poll frequency if a change is anticipated.
Otherwise a user might be a bit confused to have to wait up to a minute
in order to see a change this should be visible immediatly.
However there is no guarantee that the change will happen during the
time frame the poll frequency is increased.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove all ifdefs from topology code and also only compile it for the
CONFIG_SCHED_BOOK case. The new code selects SCHED_MC if SCHED_BOOK is
selected. SCHED_MC without SCHED_BOOK is not possible anymore.
Furthermore various sysfs attributes are not available anymore for the
!SCHED_BOOK case. In particular all attributes that correspond to
CPU polarization.
But since all real world kernels have SCHED_BOOK selected anyway this
doesn't matter too much.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Both functions take an int instead of an unsigned int. Fixes these
compile warnings:
kernel/sched.c:7167:2: warning: initialization from incompatible pointer type
kernel/sched.c:7170:2: warning: initialization from incompatible pointer type
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Export the cpu configuration topology via sysinfo. Two new lines are
introduced:
CPU Topology HW: 0 0 0 4 6 4
CPU Topology SW: 0 0 0 0 4 24
The HW line describes the cpu topology nesting levels when the maximum
nesting level is used to get the corresponding SYSIB.
The SW line describes what Linux is actually using. In this case it
supports only two levels (CONFIG_SCHED_BOOK off) and therefore the
hardware folded the two lower levels in the SYSIB response block.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the extended cpu topology information that z11 machines provide
to improve the scheduler's decision making.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20100831082844.604956770@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use default MC sched domain initializer, since performance meassurements
finally showed that this is indeed better.
Besides the fact that the powersavings flags functions didn't make too
much sense, but were unused anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Provide a topology_core_id define which makes sure that the contents of
/sys/devices/system/cpu/cpuX/topology/core_id
indeed do contain the core id and not always 0.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Impact: cleanup
cpu_coregroup_mask is the New Hotness.
As S/390 uses theirs internally, so we just make it static.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The default values for SD_MC_INIT cause an additional cpu usage of up
to 40% on some network benchmarks compared to the plain SD_CPU_INIT
values. So just define SD_MC_INIT to SD_CPU_INIT.
More tuning needs to be done.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Impact: New API
The old topology_core_siblings() and topology_thread_siblings() return
a cpumask_t; these new ones return a (const) struct cpumask *.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Like cpu_coregroup_map, but returns a (const) pointer.
Compile-tested on s390 (defconfig).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
