This is based on a similar patch from Alexandre Demers.
While fixing up some warnings with that patch I saw some
additional cleanups that could be applied. This patch
simplifies the logic for patching the power state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Alexandre Demers <alexandre.f.demers@gmail.com>
With CONFIG_ACPI=n the following build warning is seen:
drivers/gpu/drm/radeon/ni_dpm.c:3448:31: warning: unused variable 'eg_pi' [-Wunused-variable]
Move the definition of eg_pi inside the CONFIG_ACPI 'if' block.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
filter out mclk and sclk levels higher than listed in the clk
voltage dependency tables. Supporting these clocks will require
additional driver tweaking that isn't supported yet.
See bug:
https://bugs.freedesktop.org/show_bug.cgi?id=68235
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calling force_performance_level() from set_power_state()
doesn't work on some asics because the current power
state pointer has not been properly updated at that point.
Move the calls to force_performance_level() out of the
asic specific set_power_state() functions and into
the main power state sequence.
Fixes dpm resume on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check to make sure the dc limits are valid before using them.
Some systems may not have a dc limits table. In that case just
use the ac limits. This fixes hangs on systems when the power
state is changed when on battery (dc) due to invalid performance
state parameters.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=68708
v2: fix up limits in dpm_init()
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
According to the internal teams, we never hit the limit for
mclk switching on these asics, so we can disable the check.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check for engine and memory clock ss separately
and only enable dynamic ss if either of them are found.
This should fix systems which have a ss table, but do
not have entries for engine or memory. On those systems
we may enable dynamic spread spectrum without enabling
it on the engine or memory clocks which can lead to a
hang in some cases.
fixes some systems reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
v2: fix typo
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On rv770 and newer, clock gating is not required
for thermal protection. The only requirement is that
the design utilizes a thermal sensor.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Was disabled due to stability issues on certain boards
caused by the a bug in the parsing of the atom mc reg tables.
That's fixed now so re-enable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for SI asics. This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2/gen3 switching
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: enable hainan support, rebase
v3: guard acpi stuff
v4: fix 64 bit math
v5: fix 64 bit div harder
v6: fix thermal interrupt check noticed by Jerome
v7: attempt fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Validate the voltages against the voltage requirements of the
dispclk. We currently don't adjust the disp clock so it never
changes, but we need to filter out voltage levels that are too
low none the less.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This properly implemented dynamic state adjustment by
using a working copy of the requested and current
power states.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for cayman asics. This includes:
- clockgating
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2 switching (requires additional acpi support)
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: fold in tdp fix
v3: fix indentation
v4: fix 64 bit div
v5: attempt to fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
