[Why]
It fixes the failure to create stream for sink in the scenario
when hotplug SST and MST in sequence, and disconnect MST.
[How]
Add the fake sink back after the majority of MST rework is done.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Setting monitor refresh rate below freesync range would cause the
monitor to go blank indefinitely with freesync enabled
[How]
Set vrr_supported and ignore_msa_timing_param according to whether
the refresh rate is above or below the minimum freesync frequency.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This provides little debug value and creates a lot of dmesg noise.
[How]
Remove it.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The stream_update struct is left unitialized but DC will access
its fields. This usually results in global state validation occur
during any atomic commit with state->allow_modeset = true.
[How]
Initialize the struct to zero for every stream we check.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The indenting for this function is a few levels too deep and can be
simplified a fair bit. This patch is in preparation for functional
changes that fix update type determination to occur less frequently
and more accurately.
[How]
Place checks early and exit/continue when possible. This isn't
a functional change.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were always passing the first surface on the stream status for
flip updates when we should be using the surface associated with
the plane.
[How]
Use the dc_plane_state from the plane that's being updated.
FreeSync should also only keep track of updates from the primary
plane, so the check needed to be updated.
The acrtc->stream state doesn't need to be checked for NULL before
updating FreeSync either since there needs to be a stream to be
inside this function as a prerequisite.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Most surface updates weren't propagated onto the surface during
dc_commit_updates_for_stream. This makes it more difficult for DC to
determine the actual surface update type required.
[How]
Use copy_surface_update_to_plane to propagate the changes. The FreeSync
surface timing information update for BTR has been moved out of
amdgpu_dm.c into this function as well.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When CONFIG_DEBUG_FS isn't defined then amdgpu_dm_crtc_set_crc_source
is NULL. This causes a compilation error since it's being called
unconditionally.
[How]
Guard the call based on CONFIG_DEBUG_FS - CRC capture isn't supported
without this.
Cc: Leo Li <sunpeng.li@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Fixes: 43a6a02eb3 ("drm/amd/display: Re-enable CRC capture following modeset")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:2314:38:
warning: suggest braces around initialization of subobject
[-Wmissing-braces]
struct dc_surface_dcc_cap output = {0};
^
{}
Previous efforts to fix this type of warning by adding or removing
braces have been met with some pushback in favor of using memset [1][2].
Do that here, mirroring commit 05794eff1a ("drm/amdgpu/gmc: fix
compiler errors [-Werror,-Wmissing-braces] (V2)") in this tree.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
Fixes: 7df7e505e8 ("drm/amd/display: Set requested plane state DCC params for GFX9")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns:
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5089:60:
warning: suggest braces around initialization of subobject
[-Wmissing-braces]
struct dc_surface_update dummy_updates[MAX_SURFACES] = { 0 };
^
{}
Previous efforts to fix this type of warning by adding or removing
braces have been met with some pushback in favor of using memset [1][2].
Do that here, mirroring commit 05794eff1a ("drm/amdgpu/gmc: fix
compiler errors [-Werror,-Wmissing-braces] (V2)") in this tree.
[1]: https://lore.kernel.org/lkml/022e41c0-8465-dc7a-a45c-64187ecd9684@amd.com/
[2]: https://lore.kernel.org/lkml/20181128.215241.702406654469517539.davem@davemloft.net/
Fixes: 02d6a6fcdf ("drm/amd/display: Simplify underscan and ABM commit")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The flip and full structures were allocated but never freed.
[How]
Free them at the end of the function. There's a small behavioral
change here with the function returning early if the allocation fails
but we wouldn't should be doing anything in that case anyway.
Fixes: c00e0cc0fdc0 ("drm/amd/display: Call into DC once per multiplane flip")
Fixes: ea39594e0855 ("drm/amd/display: Perform plane updates only when needed")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During any modeset the CRTC stream is removed and a new stream is added.
This new stream doesn't carry over CRC capture state if it was
previously set.
[How]
Re-program the stream for CRC capture. The existing DRM callback can
be re-used here for the most part - the only modification needed is
additional locking now that it's called from within commit tail.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In order to read CRC events when CRC capture is enabled the vblank
interrput handler needs to be running for the CRTC. The handler is
enabled while there is an active vblank reference.
When running IGT tests there will often be no active vblank reference
but the test expects to read a CRC value. This is valid usage (and
works on i915 since they have a CRC interrupt handler) so the reference
to the vblank should be grabbed while capture is active.
This issue was found running:
igt@kms_plane_multiple@atomic-pipe-b-tiling-none
The pipe-b is the only one in the initial commit and was not previously
active so no vblank reference is grabbed. The vblank interrupt is
not enabled and the test times out.
[How]
Keep a reference to the vblank as long as CRC capture is enabled.
If userspace never explicitly disables it then the reference is
also dropped when removing the CRTC from the context (stream = NULL).
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On current design, driver cannot handle the interrupt for
down reply when link training is processing. The DOWN REQ
send before link training will keep in the pending DOWN REP
state in the queue.
It makes the next DOWN REQ be queued until time out.
[How]
To add a polling sequence before clear payload allocation table
to make sure the pending DOWN REP can be handled.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We were assuming that any commit with allow_modeset == false
was a pageflip. This was against drm intention and only
worked by sheer luck
[How]
A pageflip is the change from one framebuffer to another
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Our old logic: if pageflip, update freesync and plane address.
Otherwise, update everything.
This over-updated on non-pageflip cases, and it failed to
update if pageflip and non-pageflip changes occurred on
the same commit
[How]
Update flip_addrs on pageflips.
Update scaling_info when it changes.
Update color fields on color changes.
Updates plane_info always because we don't have a good way of
knowing when it needs to be updated.
Unfortunately, this means that every stream commit involves two
calls into DC. In particular, on pageflips there is a second,
pointless update that changes nothing but costs several
microseconds (about a 50% increase in time taken). The update is
fast, but there are comparisons and some useless programming.
Leave TODOs indicating dissatisfaction.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
amdgpu_dm_commit_planes was performing multi-plane
flips incorrectly:
It waited for vblank once per flipped plane
It prepared flip ISR and acquired the corresponding vblank ref
once per plane, although it closed ISR and put the ref once
per crtc
It called into dc once per flipped plane, duplicating some work
[How]
Wait for vblank, get vblank ref, prepare flip ISR, and call into
DC only once, and only if there is a pageflip
Make freesync continue to update planes even if vrr information
has already been changed
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underscan and ABM are connector properties but require updates
to DC stream state. Previously, on updates to these properties
the affected stream and all its planes were committed.
This is unnecessary; only a few fields on the stream need
to be changed.
[How]
If scaling or ABM have changed, change the stream and
create a stream update with those changes. Call
DC with only those fields.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Replace kzalloc() function with its 2-factor argument form, kcalloc().
This patch replaces cases of:
kzalloc(a * b, gfp)
with:
kcalloc(a, b, gfp)
Also, improve the coding style and the use of sizeof during
allocation by changing sizeof(struct dc_surface_update) and
sizeof(struct dc_plane_state) to sizeof(*updates) and
sizeof(*surfaces), correspondingly.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check if crtc state is changed so that mode set is
required before trying to create new stream.
It deals with the MST hotplug use case when plug back to the
same connector where the failure to create new stream for the
inactive crtc on the old connector.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] clarify dal input parameters to pplib interface, remove
un-used parameters. dal knows exactly which parameters needed
and their effects at pplib and smu sides.
current dal sequence for dcn1_update_clock to pplib:
1.smu10_display_clock_voltage_request for dcefclk
2.smu10_display_clock_voltage_request for fclk
3.phm_store_dal_configuration_data {
set_min_deep_sleep_dcfclk
set_active_display_count
store_cc6_data --- this data never be referenced
new sequence will be:
1. set_display_count --- need add new pplib interface
2. set_min_deep_sleep_dcfclk -- new pplib interface
3. set_hard_min_dcfclk_by_freq
4. set_hard_min_fclk_by_freq
after this code refactor, smu10_display_clock_voltage_request,
phm_store_dal_configuration_data will not be needed for rv.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
aux_payload should be the struct used inside dc to start
aux transactions. This will allow the old aux interface
to be seamlessly replaced.
[How]
Add three fields to aux_payload: reply, mot, defer_delay
This will mean that aux_payload has all data required
to submit a request. Shift dc_link to use this struct
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 717276b925.
The reverted patch was a workaround that addressed an issue fixed by:
4364bcb2cd ("drm: Get ref on CRTC commit object when waiting for
flip_done")
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes a stuttering issue that occurs when moving a hardware cursor
when VRR is enabled.
Previously when VRR is enabled atomic check will grab the connector
state for every atomic update. This has to lock the connector in order
to do so. The locking is bad enough by itself for performance, but
it gets worse with what we do just below that - add all the planes
for the CRTC to the commit.
This prevents the cursor fast path from working - there's more than one
plane now. With state->allow_modeset = true on top of this, it also
adds and removes all the planes from the DC context triggering a full
(very slow) update in DC.
[How]
We need the connector state to get the VRR min/max capbilities, but we
only need them when there's a CRTC mode change or when VRR is toggled.
The condition has been updated accordingly.
Fixes: 3cc22f281318 ("drm/amdgpu: Set FreeSync state using drm VRR properties")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To reduce indent in dm_update_crtcs, and to make it operate on single
instances.
[How]
Move iteration of plane states into atomic_check.
No functional change is intended.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To reduce indentation of dm_update_planes, and to make it operate on
single plane instances.
[How]
Move iteration of plane states into atomic_check.
No functional change is intended.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardware support for Delta Color Compression (DCC) decompression is
available in DC for GFX9 but there's no way for userspace to enable
the feature.
Enabling the feature can provide improved GFX performance and
power savings in many situations.
[How]
The GFX9 DCC parameters are passed to amdgpu_dm from AMDGPU via the
amdgpu_bo tiling_flags. The plane capability is queried and the
parameters are set accordingly.
The DCC address is given via a 256 byte aligned offset on the
framebuffer address. The DCC address is updated whenever the buffer
address changes.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function dc_commit_updates_for_stream had a parameter called
plane_states. It was never used. It was getting in the way
of some cleanup work
[How]
Remove it
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This fixes an regression introduced by:
drm/amd/display: add stream ID and otg instance in dc_stream_state
During driver initialization, a null pointer deref is raised. This is
caused by searching for a stream status in the dc->current_state before
the dc_state swap happens at the end of dc_commit_state_no_check().
Since the swap has not happened, the dc_state to be swapped in should
be searched, and not dc->current_state.
[How]
Add a function that searches for the stream status within the given
dc_state, instead of dc->current_state. Use that before the state swap
happens in dc_commit_state_no_check().
Also remove duplicate occurrences of this function in amdgpu_dm.c.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Users would like more accurate pixel clocks, especially for fractional
"TV" frame rates like 59.94 Hz.
[How]
Store and communicate pixel clocks with 100 Hz accuracy from
dc_crtc_timing through to BIOS command table setpixelclock call.
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
ABM enablement testing can be automated if a way of reading
target and current hardware backlight is available
[How]
Expand debugfs interface with two new entries.
Hook directly into dc interface. Units are as
a fraction of 0x1000 = 100%
Use the built-in amdgpu function for creating
read-only debugfs files
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Backlight is conceptually a property of links, not streams.
All backlight programming is done on links, but there is a
stream property bl_pwm_level that is used to restore backlight
on dpms on and s3 resume. This is unnecessary, as backlight
is already restored by hardware with no driver intervention.
[How]
Remove bl_pwm_level, and the stream argument to set_backlight
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_stream_state containing a pointer to sink is poor design.
Sink describes the display, and the specifications or capabilities
it has. That information is irrelevant for dc_stream_state, which describes
hardware state, and is generally used for hardware programming. It
could further be argued that dc_sink itself is just a convenience dc
provides, and DC should be perfectly capable of programming hardware
without any dc_sinks (for example, emulated sinks).
[how]
Phase 1:
Deprecate use of dc_sink pointer in dc_stream. Most references are trivial
to remove, but some call sites are risky (such as is_timing_changed) with
no obvious logical replacement. These will be removed in follow up change.
Add dc_link pointer to dc_stream. This is the typical reason DC really needed
sink pointer, and most call sites are replaced with this.
DMs also need minor updates, as all 3 DMs leverage stream->sink for
some functionality. this is replaced instead by a pointer to private data
inside dc_stream_state, which is used by DMs as a quality of life improvment
for some key functionality. it allows DMs to set pointers have to their own objects
which associate OS objects to dc_stream_states (such as DisplayTarget
and amdgpu_dm_connector). Without the private pointer, DMs would be
forced to perform a lookup for callbacks.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXDOTqAAKCRDj7w1vZxhR
xZ8QAQD4j8m9Ea3bzY5Rr8BYUx1k+Cjj6Y6abZmot2rSvdyOHwD+JzJFIFAPZjdd
uOKhLnDlubaaoa6OGPDQShjl9p3gyQE=
=WQGO
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-01-07-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
Cross-subsystem Changes:
- Turn dma-buf fence sequence numbers into 64 bit numbers
Core Changes:
- Move to a common helper for the DP MST hotplug for radeon, i915 and
amdgpu
- i2c improvements for drm_dp_mst
- Removal of drm_syncobj_cb
- Introduction of an helper to create and attach the TV margin properties
Driver Changes:
- Improve cache flushes for v3d
- Reflection support for vc4
- HDMI overscan support for vc4
- Add implicit fencing support for rockchip and sun4i
- Switch to generic fbdev emulation for virtio
Signed-off-by: Dave Airlie <airlied@redhat.com>
[airlied: applied amdgpu merge fixup]
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190107180333.amklwycudbsub3s5@flea
-----BEGIN PGP SIGNATURE-----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=hFld
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Happy New Year, just decloaking from leave to get some stuff from the
last week in before rc1:
core:
- two regression fixes for damage blob and atomic
i915 gvt:
- Some missed GVT fixes from the original pull
amdgpu:
- new PCI IDs
- SR-IOV fixes
- DC fixes
- Vega20 fixes"
* tag 'drm-next-2019-01-05' of git://anongit.freedesktop.org/drm/drm: (53 commits)
drm: Put damage blob when destroy plane state
drm: fix null pointer dereference on null state pointer
drm/amdgpu: Add new VegaM pci id
drm/ttm: Use drm_debug_printer for all ttm_bo_mem_space_debug output
drm/amdgpu: add Vega20 PSP ASD firmware loading
drm/amd/display: Fix MST dp_blank REG_WAIT timeout
drm/amd/display: validate extended dongle caps
drm/amd/display: Use div_u64 for flip timestamp ns to ms
drm/amdgpu/uvd:Change uvd ring name convention
drm/amd/powerplay: add Vega20 LCLK DPM level setting support
drm/amdgpu: print process info when job timeout
drm/amdgpu/nbio7.4: add hw bug workaround for vega20
drm/amdgpu/nbio6.1: add hw bug workaround for vega10/12
drm/amd/display: Optimize passive update planes.
drm/amd/display: verify lane status before exiting verify link cap
drm/amd/display: Fix bug with not updating VSP infoframe
drm/amd/display: Add retry to read ddc_clock pin
drm/amd/display: Don't skip link training for empty dongle
drm/amd/display: Wait edp HPD to high in detect_sink
drm/amd/display: fix surface update sequence
...
Resolves __udivdi3 missing errors when building for i386.
Fixes: 6378ef012ddc ("drm/amd/display: Add below the range support for FreeSync")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When the flip-rate is below the minimum supported variable refresh rate
range for the monitor the front porch wait will timeout and be
frequently misaligned resulting in stuttering and/or flickering.
The FreeSync module can still maintain a smooth and flicker free
image when the monitor has a refresh rate range such that the maximum
refresh > 2 * minimum refresh by utilizing low framerate compensation,
"below the range".
[How]
Hook up the pre-flip and post-flip handlers from the FreeSync module.
These adjust the minimum/maximum vrr range to duplicate frames
when appropriate by tracking flip timestamps.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The behavior of drm_atomic_helper_cleanup_planes differs depending on
whether the commit was asynchronous or not. When it's called from
amdgpu_dm_atomic_commit_tail during a typical atomic commit the
plane state has been swapped so it calls cleanup_fb on the old plane
state.
However, in the asynchronous commit codepath the call to
drm_atomic_helper_commit also calls dm_plane_helper_cleanup_fb after
atomic_async_update has been called. Since the plane state is updated
in place and has not been swapped the cleanup_fb call affects the new
plane state.
This results in a use after free for the given sequence:
- Fast update, fb1 pin/ref, fb1 unpin/unref
- Fast update, fb2 pin/ref, fb2 unpin/unref
- Slow update, fb1 pin/ref, fb2 unpin/unref
- Fast update, fb2 pin/ref -> use after free. bug
[How]
Disallow framebuffer changes in the fast path. Since this includes
a NULL framebuffer, this means that only framebuffers that have
been previously pin+ref at least once will be used, preventing a
use after free.
This has a significant throughput reduction for cursor updates where
the framebuffer changes. For most desktop usage this isn't a problem,
but it does introduce performance regressions for two specific IGT
tests:
- cursor-vs-flip-toggle
- cursor-vs-flip-varying-size
Fixes: 2cc751931afc ("drm/amd/display: Add fast path for cursor plane updates")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Legacy cursor plane updates from drm helpers go through the full
atomic codepath. A high volume of cursor updates through this slow
code path can cause subsequent page-flips to skip vblank intervals
since each individual update is slow.
This problem is particularly noticeable for the compton compositor.
[How]
A fast path for cursor plane updates is added by using DRM asynchronous
commit support provided by async_check and async_update. These don't do
a full state/flip_done dependency stall and they don't block other
commit work.
However, DC still expects itself to be single-threaded for anything
that can issue register writes. Screen corruption or hangs can occur
if write sequences overlap. Every call that potentially perform
register writes needs to be guarded for asynchronous updates to work.
The dc_lock mutex was added for this.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=106175
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These properties aren't being carried over when the atomic state.
This tricks atomic check and commit tail into performing underscan
and scaling operations when they aren't needed.
With the patch that forced scaling/RMX_ASPECT on by default this
results in many unnecessary surface updates and hangs under certain
conditions.
[How]
Duplicate the properties.
Fixes: 91b66c47ba ("drm/amd/display: Set RMX_ASPECT as default")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the "max bpc" isn't explicitly set in the atomic state then it
have a value of 0. This has the correct behavior of limiting a panel
to 8bpc in the case where the panel supports 8bpc. In the case of eDP
panels this isn't a true assumption - there are panels that can only
do 6bpc.
Banding occurs for these displays.
[How]
Initialize the max_bpc when the connector resets to 8bpc. Also carry
over the value when the state is duplicated.
Bugzilla: https://bugs.freedesktop.org/108825
Fixes: 307638884f72 ("drm/amd/display: Support amdgpu "max bpc" connector property")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 91b66c47ba.
Forcing RMX_ASPECT as default uses the preferred/native mode's timings
for any mode the user selects and scales the image. This provides a
a consistently nicer result in the case where the selected mode's
refresh rate matches the native mode's refresh but this isn't always
the case.
For example, if the monitor is 1080p@144Hz and the preferred mode is
60Hz then even if the user selects 1080p@144Hz as their selected mode
they'll get 1080p@60Hz.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When everyone implements it exactly the same way, among all 4
implementations, there's not really a need to overwrite this at all.
Aside: drm_kms_helper_hotplug_event is pretty much core functionality
at this point. Probably should move it there.
Reviewed-by: Lyude Paul <lyude@redhat.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181128221234.15054-1-daniel.vetter@ffwll.ch
[Why]
Tracing is a useful and cheap debug functionality
[How]
This creates a new trace system amdgpu_dm, currently with
three trace events
amdgpu_dc_rreg and amdgpu_dc_wreg report the address and value
of any dc register reads and writes
amdgpu_dc_performance requires at least one of those two to be
enabled. It counts the register reads and writes since the
last entry
v2: Don't check for NULL before kfree
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
New GCC warnings for stringop-truncation and stringop-overflow help
catch common misuse of strncpy. This patch suppresses these warnings
by fixing bugs identified by them.
[How]
Since the parameter passed for name in amdpgu_dm_create_common_mode has
no fixed length, if the string is >= DRM_DISPLAY_MODE_LEN then
mode->name will not be null-terminated.
The truncation in fill_audio_info won't actually occur (and the string
will be null-terminated since the buffer is initialized to zero), but
the warning can be suppressed by using the proper buffer size.
This patch fixes both issues by using the real size for the buffer and
making use of strscpy (which always terminates).
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When running igt@kms_plane@pixel-format-pipe-* tests the CRC read will
time out and the test will fail.
This is because the CRTC is duplicated but the crc_enabled parameter
isn't copied over to the new dm_crtc_state. CRC reads will time out
because amdgpu_dm_crtc_handle_crc_irq will no longer call
drm_crtc_add_crc_entry.
[How]
Copy crc_enabled when duplicating the state.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Use provided infopacket in stream (if valid) instead of reconstructing
in set_vendor_info_packet()
* Use proper format for enums
* Use dc info packet struct instead
Signed-off-by: Harmanprit Tatla <Harmanprit.Tatla@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
With scaling, underscan and abm changes we can end up calling
commit_planes_to_stream in commit_tail. This call uses dm_state->context
which can be NULL if the commit was a fast update.
[How]
Use dc_state instead since that can't be NULL unless the system ran
out of memory.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108912
Fixes: e64abff2f133 ("drm/amd/display: Use private obj helpers for dm_atomic_state")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
